Adding an ATM High-Speed LIM

This procedure is used to add an ATM high-speed LIM to the database using the ent-card command.

The ent-card command uses these parameters.

:loc – The location of the card being added to the database.

:type – The type of card being added to the database.

:appl – The application software that is assigned to the card.

:force – If the global title translation feature is on, the force=yes parameter allows the LIM to be added to the database even if the current SCCP transactions-per-second threshold is unable to support the additional SCCP transaction-per-second capacity created by adding the LIM. This parameter is obsolete and is no longer used.

Note:

As of Release 46.6, E5-ATM refers to the E5-ATM-B (P/N 870-2972-xx) card.

Table C-9 shows the valid card type (type) and card application (appl) combinations for the ATM high-speed LIMs being added to the database and the names and part numbers of the hardware. This can be used to verify that the ATM high-speed LIM being added to the database matches the card physically installed in the EAGLE. See the Determining the Number of High-Speed and Low-Speed Signaling Links section for information on the maximum number of ATM high-speed LIMs that can be configured in the database.

Table C-9 ATM High-Speed LIM Card Type and Card Application Combinations

Card Name	Part Number	Card Type (:type)	Application Type (:appl)
E5-ATM-B	870-2972-01	limatm	atmansi
		lime1tam	atmitu

The shelf to which the card is to be added, must already be in the database. This can be verified with the rtrv-shlf command. If the shelf is not in the database, go to the Adding a Shelf procedure in the Database Administration - System Management User's Guide and add the shelf.

The examples in this procedure are used to add the cards shown in Table C-10 to the database.

Table C-10 Example Card Configuration

Card Type	Application	Card Location
limatm (E5-ATM)	atmansi	2207
lime1atm (E5-ATM)	atmitu	2205

Note:

If an E5-ATM is being added as the ATM high-speed LIM, verify the temperature alarm threshold settings for the E5-ATM card by performing the Changing the High-Capacity Card Temperature Alarm Thresholds procedure.

1. Display the cards in the database using the rtrv-card command.

   This is an example of the possible output.

   rlghncxa03w 09-05-28 09:12:36 GMT EAGLE5 41.0.0
   CARD   TYPE      APPL     LSET NAME   LINK SLC LSET NAME   LINK SLC
   1102   TSM       GLS     
   1113   GSPM      OAM
   1114   TDM-A
   1115   GSPM      OAM
   1116   TDM-B
   1117   MDAL
   1201   LIMDS0    SS7ANSI  sp2         A    0   sp1         B    0
   1203   LIMDS0    SS7ANSI  sp3         A    0   
   1204   LIMDS0    SS7ANSI  sp3         A    1   
   1206   LIMDS0    SS7ANSI  nsp3        A    1   nsp4        B    1
   1216   DCM       STPLAN   
   1301   DSM       VSCCP     
   1308   LIMDS0    SS7ANSI  sp6         A    1   sp7         B    0
   1314   LIMDS0    SS7ANSI  sp7         A    1   sp5         B    1
   1317   DCM       STPLAN   
   

   The cards should be distributed throughout the EAGLE for proper power distribution. Refer to Installation Guide for the shelf power distribution.

2. Using Table C-9 as a reference, verify that the card has been physically installed into the proper location.
   • If an E5-ATM card is not being provisioned in this procedure, continue the procedure with 7.
   • If an E5-ATM card is being provisioned in this procedure, continue the procedure with the next step.
3. Verify that HIPR2 cards are installed at card locations 9 and 10 in the shelf where the E5-ATM card will be installed. Enter this command..

   rept-stat-gpl:gpl=hipr2

   This is an example of the possible output.

   rlghncxa03w 09-07-05 08:12:53 GMT  41.1.0
   GPL        CARD      RUNNING            APPROVED      TRIAL
   HIPR2      1109      126-002-000        126-002-000   126-003-000
   HIPR2      1110      126-002-000        126-002-000   126-003-000
   HIPR2      1209      126-002-000        126-002-000   126-003-000
   HIPR2      1210      126-002-000        126-002-000   126-003-000
   HIPR2      1309      126-002-000        126-002-000   126-003-000
   HIPR2      1310      126-002-000        126-002-000   126-003-000
   HIPR2      2109      126-002-000        126-002-000   126-003-000
   HIPR2      2110      126-002-000        126-002-000   126-003-000
   Command Completed
   

   If HIPR2 cards are installed at card locations 9 and 10 in the shelf where the E5-ATM card will be installed, continue the procedure with 7.

   If HIPR2 cards are not installed at card locations 9 and 10 in the shelf where the E5-ATM card will be installed, go to Installation Guide and install the HIPR2 cards. Once the HIPR2 cards have been installed, continue the procedure with 7.

4. If the card is an EPM-B based card (E5-ATM-B), enter the rtrv-stpopts command to verify whether or not the MFC option is on. If the card is not an EPM-B based card, continue the procedure with 5

   This is an example of the possible output.

   
   rlghncxa03w 11-10-17 16:02:05 GMT EAGLE5 44.0.0
   STP OPTIONS         
   ---------------------------
   MFC                     off
   
   

   The rtrv-stpopts command output contains other fields that are not used by this procedure. To see all fields displayed by the rtrv-stpopts command, see the rtrv-stpopts command description in the Commands User's Guide.

   If the MFC option is off, perform the Configuring the MFC Option procedure in Database Administration - System Management User's Guide to turn on the MFC option.

   If the MFC option is on or the MFC Option procedure in Database Administration - System Management User's Guide was performed in this step, continue the procedure with 7.

5. The Fan feature must be turned on. If the fan feature is off, enter the rtrv-feat command to verify that the Fan feature is on.

   If the Fan feature is on, shown in the rtrv-feat output in this step, the FAN field should be set to on.

   The rtrv-feat command output contains other fields that are not used by this procedure. To see all fields displayed by the rtrv-feat command, see the rtrv-feat command description in Commands User's Guide.

   If the Fan feature is on, continue the procedure with 7.

   If the Fan feature is off, continue the procedure with 6.

6. Turn the Fan feature on by entering this command.

   chg-feat:fan=on

   Note:

   Once the Fan feature is turned on with thechg-feat command, it cannot be turned off.

   When the chg-feat has successfully completed, this message appears.

   rlghncxa03w 11-10-28 11:43:04 GMT EAGLE5 44.0.0
   CHG-FEAT: MASP A - COMPLTD
   

7. Add the card using the ent-card command. For this example, enter these commands.

   ent-card:loc=1318:type=limatm:appl=atmansi

   ent-card:loc=2101:type=lime1atm:appl=atmitu

   ent-card:loc=2207:type=limatm:appl=atmansi

   ent-card:loc=2205:type=lime1atm:appl=atmitu

   When each of these commands have successfully completed, this message should appear.

   rlghncxa03w 06-10-12 09:12:36 GMT  EAGLE5 36.0.0
   ENT-CARD: MASP A - COMPLTD
   

8. Verify the changes using the rtrv-card command with the card location specified.

   For this example, enter these commands.

   rtrv-card:loc=1318

   This is an example of the possible output.

   rlghncxa03w 06-10-28 09:12:36 GMT EAGLE5 36.0.0
   CARD   TYPE      APPL     LSET NAME   LINK SLC LSET NAME   LINK SLC
   1318   LIMATM    ATMANSI  
   

   rtrv-card:loc=2101

   This is an example of the possible output.

   rlghncxa03w 06-10-28 09:12:36 GMT EAGLE5 36.0.0
   CARD   TYPE      APPL     LSET NAME   LINK SLC LSET NAME   LINK SLC
   2101   LIME1ATM  ATMITU  
   

   rtrv-card:loc=2207

   This is an example of the possible output.

   rlghncxa03w 06-10-28 09:12:36 GMT EAGLE5 36.0.0
   CARD   TYPE      APPL     LSET NAME   LINK SLC LSET NAME   LINK SLC
   2207   LIMATM    ATMANSI  
   

   rtrv-card:loc=2205

   This is an example of the possible output.

   rlghncxa03w 06-10-28 09:12:36 GMT EAGLE5 36.0.0
   CARD   TYPE      APPL     LSET NAME   LINK SLC LSET NAME   LINK SLC
   2205   LIME1ATM  ATMITU  
   

9. Back up the new changes using the chg-db:action=backup:dest=fixed command.

   These messages should appear, the active Maintenance and Administration Subsystem Processor (MASP) appears first.

   BACKUP (FIXED) : MASP A - Backup starts on active MASP.
   BACKUP (FIXED) : MASP A - Backup on active MASP to fixed disk complete.
   BACKUP (FIXED) : MASP A - Backup starts on standby MASP.
   BACKUP (FIXED) : MASP A - Backup on standby MASP to fixed disk complete.
   

Figure C-11 Adding an ATM High-Speed LIM

Sheet 1 of 2

Sheet 2 of 2