Go to primary content
Oracle® Communications EAGLE Database Administration - SS7 User's Guide
Release 46.6
E93318 Revision 1
Go To Table Of Contents
Contents

Previous
Previous
Next
Next

Using Proxy Point Codes and Secondary Point Codes when Adding a Linkset

This procedure is used to verify that the following items are configured in the database.
  • Proxy point codes for adding proxy linksets
  • Secondary point codes for adding multiple linksets with the same adjacent point code.

To add a proxy linkset, a proxy point code must be assigned to the APC of the linkset, a proxy point code must be assigned to the linkset with the ppc/ppca/ppci/ppcn/ppcn24 parameter, and the linkset type must be prx. A quantity of proxy point codes must be enabled with the enable-ctrl-feat command before a proxy point code and a proxy linkset can be added. The first time a proxy linkset is added, the proxy point code that is assigned to the linkset must be the same proxy point code that is assigned to the APC of the proxy linkset. A maximum of 10 linksets can be added using the same proxy point code. For more information on proxy point codes, refer to Proxy Point Codes.

To add more than one linkset with the same APC, the Multiple Linksets to Single Adjacent PC feature must be enabled and turned on. The database can contain a maximum of six linksets that have the same APC. If the linkset is not a proxy linkset (linkset types A, B, C, D, or E), a secondary point code (shown in the rtrv-spc output) must be specified with the linkset. The network type and format of the secondary point code must be the same as the APC of the linkset. Secondary point codes can also be assigned to the APC of the linkset when the point code is added in the database with the ent-dstn or chg-dstn commands. The secondary point code that is assigned to the linkset with the spc/spca/spci/spcn/spcn24 parameter cannot be the same secondary point code that is assigned to the APC of the linkset.

If the linkset is a proxy linkset (linkset type PRX), a proxy point code (shown in the rtrv-dstn output) must be specified with the linkset. The proxy point code is assigned to the linkset with the ppc/ppca/ppci/ppcn/ppcn24 parameter. The network type and format of the proxy point code must be the same as the APC of the linkset. If proxy linksets are added, the database must contain one proxy linkset with a proxy point code assigned to the APC of the linkset and the same proxy point code must be assigned to the linkset. The proxy point code that is assigned to the other proxy linksets using this APC cannot be the same as the proxy point code that is assigned to the APC of the linkset.

  1. Display the current linkset configuration using the rtrv-ls command.

    This is an example of the possible output.

    rlghncxa03w 08-12-10 11:43:04 GMT EAGLE5 40.0.0
    
                                     L3T SLT              GWS GWS GWS
    LSN           APCA   (SS7)  SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
    e1e2          001-207-000   none 1   1   no  B   6    off off off no    off
    ls1305        001-005-000   none 1   1   no  A   1    off off off no    off
    ls1307        001-007-000   none 1   1   no  A   1    off off off no    off
    e1m1s1        001-001-003   none 1   1   no  A   7    off off off no    off
    e1m1s2        001-001-002   none 1   1   no  A   7    off off off no    off
    
                                     L3T SLT              GWS GWS GWS
    LSN           APCI   (SS7)  SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
    e1e2i         1-207-0       none 1   1   no  B   4    off off off ---   on
    ls1315        0-015-0       none 1   1   no  A   1    off off off ---   off
    ls1317        0-017-0       none 1   1   no  A   1    off off off ---   on
    e1m2s1        1-011-1       none 1   1   no  A   7    off off off ---   off
    e1m2s2        1-011-2       none 1   1   no  A   7    off off off ---   off
    
    Link set table is (10 of 1024) 1% full.
    

    If the APC of the linkset is not being assigned to more than one linkset and a proxy linkset is being added, continue the procedure with 8.

    If the APC of the linkset is not being assigned to more than one linkset, and a proxy linkset is not being added, this procedure is finished.

    If the APC of the linkset is being assigned to more than one linkset, and multiple linksets with the same APC are shown in the rtrv-ls output in 1, continue the procedure with 3.

    If the APC of the linkset is being assigned to more than one linkset, and multiple linksets with the same APC are not shown in the rtrv-ls output in 1, continue the procedure with 2.

  2. Verify whether or not the Multiple Linksets to Single Adjacent PC feature is enabled and turned on by entering this command.

    rtrv-ctrl-feat:partnum=893017901

    This is an example of the possible output.

    rlghncxa03w 08-12-21 15:48:20 EST  40.0.0
    The following features have been permanently enabled:
    
    Feature Name              Partnum   Status Quantity
    Multiple Linkset to APC   893019701 on     ----
    
    
    The following features have been temporarily enabled:
    
    Feature Name              Partnum   Status Quantity   Trial Period Left
    Zero entries found.
    
    
    The following features have expired temporary keys:
    
    Feature Name              Partnum
    Zero entries found.

    If the Multiple Linksets to Single Adjacent PC feature is not enabled or turned on, perform Activating the Multiple Linksets to Single Adjacent PC (MLS) Feature to enable and turn on this feature. After this feature has been enabled and turned on, continue the procedure with 3.

    If the Multiple Linksets to Single Adjacent PC feature is enabled and turned on, continue the procedure with 3.

  3. Display the linksets that contain the APC for the new linkset by entering the rtrv-ls command with the APC of the linkset. For this example, enter this command.

    rtrv-ls:apca=001-001-002

    This is an example of the possible output.

    rlghncxa03w 08-12-22 08:09:26 EST  40.0.0
    
    APCA   =    001-001-002
    
                                     L3T SLT              GWS GWS GWS
    LSN           SPCA          SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
    e1m1s2        020-020-021   none 1   1   no  A   7    off off off no    off
    
    Link set table is (10 of 1024) 1% full.

    The maximum number of linksets that can use the same APC is six. If six linksets are shown in this step, the specified APC cannot be used with the new linkset. Select another APC from the rtrv-ls output in 1 and repeat this step.

    If one to five linksets are shown in this step and the linksets are proxy linksets (lst=prx), continue the procedure with 6.

    If one to five linksets are shown in this step and the linksets are not proxy linksets, continue the procedure with 4.

  4. To use an APC for more than one linkset, a secondary point code must be assigned to the linkset. The secondary point code that will be assigned to the new linkset cannot be assigned to any of the linksets shown in 3.

    The secondary point code that will be assigned to the linkset cannot be assigned to the APC of this linkset. Verify this by entering the rtrv-dstn command with the APC of the linkset shown in 3. For this example, enter this command.

    rtrv-dstn:dpca=001-001-002

    This is an example of the possible output.

    rlghncxa03w 10-12-22 08:09:26 EST  43.0.0
    
       DPCA          CLLI        BEI ELEI   ALIASI          ALIASN/N24    DMN
       001-001-002   ----------- no  --- ----------      --------------   SS7
    
       SPCA         NCAI PRX     RCAUSE NPRST SPLITIAM HMSMSC HMSCP SCCPMSGCNV
       020-020-020  ---- no      none   off   none     no     no    none
    
    Destination table is (37 of 2000) 2% full
    Alias table is (0 of 12000) 0% full
    PPC table is (13 of 20) 65% full
    

    If a secondary point code is shown in this step, this secondary point code cannot be assigned to the new linkset.

    Continue the procedure with 5.

  5. Display the secondary point codes by entering the rtrv-spc command. This is an example of the possible output.
    rlghncxa03w 08-12-22 09:39:30 EST  40.0.0
    SPC (Secondary Point Codes)
    
    SPCA
         020-020-020
         020-020-021
         021-021-021
         022-022-022
         026-026-026
         026-026-027
         026-026-028
         026-026-029
         200-010-000
    
    SPC-I
    
    none
    
    SPC-N
            00002
    
    SPC-N24
    
    none
    
    Secondary Point Code table is (10 of 40) 25% full.
    

    If the desired secondary point code is shown in this step, this procedure is finished.

    If the desired secondary point code is not shown in this step, perform Adding a Secondary Point Code to add the desired secondary point code. The network type of the new secondary point code must be the same as the APC of the linkset. After the secondary point code has been added, this procedure is finished.

  6. To use an APC for more than one proxy linkset, a proxy point code must be assigned to the linkset. The proxy point code that will be assigned to the new linkset cannot be assigned to any of the linksets shown in 3.

    The proxy point code that will be assigned to the linkset must be in the database. Verify the proxy point codes in the database by entering the rtrv-dstn:prx=yes command.

    This is an example of the possible output.

    rlghncxa03w 09-05-22 08:09:26 EST  41.0.0
    
    PRX = yes
    
       DPCA          CLLI        BEI ELEI   ALIASI          ALIASN/N24    DMN
       002-002-002   ----------- no  --- ----------      --------------   SS7
       006-006-006   ----------- no  --- ----------      --------------   SS7
       050-050-050   ----------- no  --- ----------      --------------   SS7
       100-100-100   ----------- no  --- ----------      --------------   SS7
       100-100-101   ----------- no  --- ----------      --------------   SS7
       100-100-102   ----------- no  --- ----------      --------------   SS7
       100-100-103   ----------- no  --- ----------      --------------   SS7
       100-100-104   ----------- no  --- ----------      --------------   SS7
       200-001-001   ----------- no  --- ----------      --------------   SS7
       200-001-002   ----------- no  --- ----------      --------------   SS7
    
       DPCI          CLLI        BEI ELEI   ALIASA          ALIASN/N24    DMN
       2-003-4       ----------- no  --- --------------  --------------   SS7
    
       DPCN          CLLI        BEI ELEI   ALIASA          ALIASI        DMN
       00003         ----------- no  --- --------------  ----------       SS7
       00004         ----------- no  --- --------------  ----------       SS7
    
    Destination table is (37 of 2000) 2% full
    Alias table is (0 of 12000) 0% full
    PPC table is (13 of 20) 65% full
    

    If the desired proxy point code is not shown in this step, perform Adding a Destination Point Code to add the desired proxy point code. The network type of the new proxy point code must be the same as the APC of the linkset. After the proxy point code has been added, this procedure is finished.

    If the desired proxy point code is shown in this step, continue the procedure with 7.

  7. A proxy point code can be assigned to a maximum of 10 linksets. Verify how many linksets are using the proxy point code by entering the rtrv-dstn command with the proxy point code shown in 6. For this example, enter this command.

    rtrv-dstn:dpca=002-002-002

    This is an example of the possible output.

    rlghncxa03w 10-12-22 10:08:11 EST  43.0.0
    
       DPCA          CLLI        BEI ELEI   ALIASI          ALIASN/N24    DMN
       002-002-002   ----------- no  --- ----------      --------------   SS7
    
       SPCA         NCAI PRX     RCAUSE NPRST SPLITIAM HMSMSC HMSCP SCCPMSGCNV
       026-026-029  ---- yes, 1  none   off   none     no     no    none
    
    Destination table is (37 of 2000) 2% full
    Alias table is (0 of 12000) 0% full
    PPC table is (13 of 20) 65% full
    

    The number of linksets using the proxy point code is the number shown in the PRX column. If 10 linksets are using the proxy point code, this proxy point code cannot be assigned to any other linkset. Repeat 6 and 7.

    If the number of linksets using the proxy point code is from 0 to 9, this procedure is finished.

  8. To add a proxy linkset, a linkset whose linkset type is PRX, a quantity of proxy point codes must be enabled. Verify whether or not a quantity of proxy point codes is enabled by entering the rtrv-ctrl-feat command.

    Note:

    If proxy linksets are shown in the rtrv-ls output in 1, then a quantity of proxy point codes has been enabled. If proxy linksets are shown in the rtrv-ls output in 1, this step does not have to be performed. Continue the procedure with 9.

    This is an example of the possible output.

    rlghncxa03w 08-12-22 10:58:06 EST  40.0.0
    The following features have been permanently enabled:
    
    Feature Name              Partnum   Status Quantity
    HC-MIM SLK Capacity       893012707 on     64
    Origin-Based MTP Routing  893014201 on     ----
    Multiple Linkset to APC   893019701 on     ----
    Proxy Point Code          893018702 on     20
    
    
    The following features have been temporarily enabled:
    
    Feature Name              Partnum   Status Quantity   Trial Period Left
    Zero entries found.
    
    
    The following features have expired temporary keys:
    
    Feature Name              Partnum
    Zero entries found.
    

    If a quantity of proxy point codes is enabled, continue the procedure with 9.

    If a quantity of proxy point codes is not enabled, perform Changing the Proxy Point Code Quantity to enable a quantity of proxy point codes. After the quantity of proxy point codes is enabled, perform Adding a Destination Point Code to add the desired proxy point code to the database, then assign the proxy point code to the destination point code that will be the APC of the proxy linkset. After Adding a Destination Point Code has been performed, this procedure is finished.

  9. The APC of a proxy linkset must be a destination point code that contains a proxy point code. Verify the proxy point codes in the database by entering the rtrv-dstn:prx=yes command.

    This is an example of the possible output.

    rlghncxa03w 09-05-22 08:09:26 EST  41.0.0
    
    PRX = yes
    
       DPCA          CLLI        BEI ELEI   ALIASI          ALIASN/N24    DMN
       002-002-002   ----------- no  --- ----------      --------------   SS7
       006-006-006   ----------- no  --- ----------      --------------   SS7
       050-050-050   ----------- no  --- ----------      --------------   SS7
       100-100-100   ----------- no  --- ----------      --------------   SS7
       100-100-101   ----------- no  --- ----------      --------------   SS7
       100-100-102   ----------- no  --- ----------      --------------   SS7
       100-100-103   ----------- no  --- ----------      --------------   SS7
       100-100-104   ----------- no  --- ----------      --------------   SS7
       200-001-001   ----------- no  --- ----------      --------------   SS7
       200-001-002   ----------- no  --- ----------      --------------   SS7
    
       DPCI          CLLI        BEI ELEI   ALIASA          ALIASN/N24    DMN
       2-003-4       ----------- no  --- --------------  --------------   SS7
    
       DPCN          CLLI        BEI ELEI   ALIASA          ALIASI        DMN
       00003         ----------- no  --- --------------  ----------       SS7
       00004         ----------- no  --- --------------  ----------       SS7
    
    Destination table is (37 of 2000) 2% full
    Alias table is (0 of 12000) 0% full
    PPC table is (13 of 20) 65% full
    
  10. Display the attributes of the proxy point that will be added to the proxy linkset by entering the rtrv-dstn command with a proxy point code shown in 9. For this example, enter this command.

    rtrv-dstn:ppca=002-002-002

    This is an example of the possible output.

    rlghncxa03w 09-05-22 13:57:23 EST  41.0.0
    
    PPCA   =    002-002-002
    
       DPCA          CLLI        BEI ELEI   ALIASI          ALIASN/N24    DMN
       004-004-004   ----------- no  --- ----------      --------------   SS7
    
    Destination table is (37 of 2000) 2% full
    Alias table is (0 of 12000) 0% full
    PPC table is (13 of 20) 65% full
    

    If destination point codes are displayed in this step, continue the procedure with 11.

    If destination are not shown in this step, then the proxy point code is not assigned to any destination point codes. Perform Adding a Destination Point Code to assign the proxy point code to a destination point code. The network type of the proxy point code must be the same as the APC of the linkset. After the proxy point code has been assigned to a destination point code, this procedure is finished.

  11. A proxy point code can be assigned to a maximum of 10 linksets. Verify how many linksets are using the proxy point code by entering the rtrv-dstn command with the proxy point code shown in 10. For this example, enter this command.

    rtrv-dstn:dpca=002-002-002

    This is an example of the possible output.

    rlghncxa03w 10-12-22 10:08:11 EST  43.0.0
    
       DPCA          CLLI        BEI ELEI   ALIASI          ALIASN/N24    DMN
       002-002-002   ----------- no  --- ----------      --------------   SS7
    
       SPCA         NCAI PRX     RCAUSE NPRST SPLITIAM HMSMSC HMSCP SCCPMSGCNV
       026-026-029  ---- yes, 1  none   off   none     no     no    none
    
    Destination table is (37 of 2000) 2% full
    Alias table is (0 of 12000) 0% full
    PPC table is (13 of 20) 65% full
    

    The number of linksets using the proxy point code is the number shown in the PRX column. If 10 linksets are using the proxy point code, this proxy point code cannot be assigned to any other linkset. Repeat 10 and 11.

    If the number of linksets using the proxy point code is from 0 to 9, this procedure is finished.

Figure 3-8 Using Proxy Point Codes and Secondary Point Codes when Adding a Linkset



Sheet 1 of 7



Sheet 2 of 7



Sheet 3 of 7



Sheet 4 of 7



Sheet 5 of 7



Sheet 6 of 7



Sheet 7 of 7