Oracle® Communications EAGLE Database Administration - System Management User's Guide Release 46.6 E93319 Revision 1 |
|
![]() Previous |
![]() Next |
High-capacity cards that were issued before EAGLE Release 43.0 may not be loaded with the BLIXP GPL. This procedure updates the high-capacity card with the BLIXP GPL using the flash-card
command. The BLIXP GPL is a tar image of all the flash GPLs that are necessary to operate the high-capacity cards. The high-capacity cards are shown in Table 3-7. When the BLIXP GPL is downloaded to the card, the tar image is un-archived and the flash GPLs are loaded onto the card.
Table 3-7 High-Capacity Cards
HC MIM | E5-E1T1 | E5-ENET |
E5-STC | E5-SLAN | E5-SM4G |
E5-ATM | E5-TSM |
Caution:
Theflash-card
command cannot be entered if the IMT Rate Change sequence or the Extended Bit Error Rate Test (BERT) is being performed.The applications and entities supported by the high-capacity cards are shown in Table 3-8.
Table 3-8 High-Capacity Card Applications
High-Capacity Card | Card Name (as shown on the card label) | Application | Application GPL Running on the Card | Supported Entities |
---|---|---|---|---|
HC MIM | HC MIM | SS7ANSI, CCS71TU | SS7HC | E1 or T1 signaling links |
E5-E1T1 | E5-E1T1 | SS7ANSI, CCS71TU | SS7HC | E1 or T1 signaling links |
E5-ENET | E5-ENET | SS7IPGW, IPLIM, IPLIMI, IPGWI, IPSG | IPLHC, IPGHC, IPSG | IP signaling links |
E5-STC | E5-ENET | EROUTE | ERTHC | EAGLE 5 Integrated Monitoring Support |
E5-SM4G | E5-SM4G | VSCCP | SCCPHC | GTT-related features |
E5-SLAN | E5-ENET | STPLAN | SLANHC | TCP/IP data links for the STPLAN feature |
E5-ENET-B/SLIC | E5-ENET-B SLIC |
IPS | IPSHC | Telnet sessions for remote connections to the EAGLE and SEAS terminals for the SEAS over IP feature |
E5-ATM | E5-ATM | ATMANSI, ATMITU | ATMHC | ANSI and ITU ATM high-speed signaling links |
E5-TSM | E5-TSM | GLS | GLSHC | Gateway Screening related features |
Caution:
Before any high-capacity card can be updated with the BLIXP GPL, all the traffic hosted by the high-capacity card must be stopped, and the high-capacity card must be taken out of service.Canceling the REPT-STAT-SLK
and RTRV-SLK
Commands
Because the rept-stat-slk
and rtrv-slk
commands used in this procedure can output information for a long period of time, the rept-stat-slk
and rtrv-slk
commands can be canceled and the output to the terminal stopped. There are three ways that the rept-stat-slk
and rtrv-slk
commands can be canceled.
F9
function key on the keyboard at the terminal where the rept-stat-slk
or rtrv-slk
commands command were entered. canc-cmd
without the trm
parameter at the terminal where the rept-stat-slk
or rtrv-slk
commands were entered. canc-cmd:trm=<xx>
, where <xx>
is the terminal where the rept-stat-slk
or rtrv-slk
commands were entered, from another terminal other that the terminal where the rept-stat-slk
or rtrv-slk
commands were entered. To enter the canc-cmd:trm=<xx>
command, the terminal must allow Security Administration commands to be entered from it and the user must be allowed to enter Security Administration commands. The terminal’s permissions can be verified with the rtrv-secu-trm
command. The user’s permissions can be verified with the rtrv-user
or rtrv-secu-user
commands. For more information about the canc-cmd
command, go to Commands User's Guide.
rtrv-gpl:gpl=blixp
If E5-based control cards are installed in the EAGLE, this is an example of the possible output.
rlghncxa03w 10-12-01 11:34:04 GMT EAGLE5 43.0.0 GPL Auditing ON GPL CARD RELEASE APPROVED TRIAL REMOVE TRIAL BLIXP 1114 133-003-000 133-003-000 133-002-000 133-003-000 BLIXP 1116 133-003-000 133-003-000 133-002-000 133-003-000 BLIXP 1115 ----------- ----------- ----------- -----------
rept-stat-card
command and specifying the location of the card. For this example, enter this command.
rept-stat-card:loc=1303
For an HC MIM or E5-E1T1 card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 LIME1 SS7HC IS-NR Active ----- ALARM STATUS = No Alarms. IMTPCI GPL version = 133-002-000 BLCPLD GPL version = 133-002-000 BLDIAG6 GPL version = 133-002-000 BLBIOS GPL version = 133-002-000 BLVXW6 GPL version = 133-002-000 BLROM1 GPL version = 133-002-000 PLDPMC1 GPL version = 133-002-000 IMT BUS A = Conn IMT BUS B = Conn SIGNALING LINK STATUS SLK PST LS CLLI A IS-NR e11303a ----------- B IS-NR e11303b ----------- A1 IS-NR e11303a ----------- B3 IS-NR e11303b ----------- Command Completed.
For an E5-E1T1 card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 LIME1 SS7EPM IS-NR Active ----- ALARM STATUS = No Alarms. IMTPCI GPL version = 133-002-000 BLCPLD GPL version = 133-002-000 BLDIAG6 GPL version = 133-002-000 BLBEPM GPL version = 133-002-000 PLDPMC1 GPL version = 133-002-000 BLVXW6 GPL version = 133-002-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 32C ( 90F) [ALARM TEMP: 60C (140F)] PEAK TEMPERATURE: = 39C (103F) [06-05-02 13:40] SIGNALING LINK STATUS SLK PST LS CLLI A IS-NR e11303a ----------- B IS-NR e11303b ----------- A1 IS-NR e11303a ----------- B3 IS-NR e11303b ----------- Command Completed.
For an E5-ENET card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 DCM IPLHC IS-NR Active ----- ALARM STATUS = No Alarms. IMTPCI GPL version = 133-002-000 BLCPLD GPL version = 133-002-000 BLDIAG6 GPL version = 133-002-000 BLBEPM GPL version = 133-002-000 PLDPMC1 GPL version = 133-002-000 BLVXW6 GPL version = 133-002-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 32C ( 90F) [ALARM TEMP: 60C (140F)] PEAK TEMPERATURE: = 39C (103F) [06-05-02 13:40] SIGNALING LINK STATUS SLK PST LS CLLI A IS-NR e11303a ----------- B IS-NR e11303b ----------- A1 IS-NR e11303a ----------- B3 IS-NR e11303b ----------- Command Completed.
For an E5-STC card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 STC ERTHC IS-NR Active ----- ALARM STATUS = No Alarms. IMTPCI GPL version = 133-002-000 BLVXW6 GPL version = 133-002-000 BLDIAG6 GPL version = 133-002-000 BLBEPM GPL version = 133-002-000 BLCPLD GPL version = 133-002-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 61C (142F) PEAK TEMPERATURE: = 61C (142F) [00-02-14 10:33] EROUTE % OCCUP = 0% NTP broadcast = VALID STC IP PORT A: OOS-MT Unavail ----- ALARM STATUS = ** 0084 IP Connection Unavailable ERROR STATUS = DHCP Lease. Physical Link. STC IP PORT B: OOS-MT Unavail ----- ALARM STATUS = ** 0084 IP Connection Unavailable ERROR STATUS = DHCP Lease. Physical Link. Command Completed.
For an E5-SLAN card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 DCM SLANHC IS-NR Active ----- ALARM STATUS = No Alarms. IMTPCI GPL version = 133-002-000 BLVXW6 GPL version = 133-002-000 BLDIAG6 GPL version = 133-002-000 BLBEPM GPL version = 133-002-000 BLCPLD GPL version = 133-002-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 60C (140F) PEAK TEMPERATURE: = 63C (146F) [00-02-12 21:58] DLK A PST = IS-NR SST = Avail AST = ----- SLAN % EAGLE CAPACITY = 57% SLAN % HOST CAPACITY = 49% Command Completed.
For an E5-SM4G card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 DSM SCCPHC IS-NR Active ----- ALARM STATUS = No Alarms. IMTPCI GPL version = 133-002-000 BLVXW6 GPL version = 133-002-000 BLDIAG6 GPL version = 133-002-000 BLBSMG GPL version = 133-002-000 BLCPLD GPL version = 133-002-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 31C ( 88F) PEAK TEMPERATURE: = 32C ( 90F) [07-05-12 15:55] SCCP % OCCUP = 1% Command Completed.
For an E5-ENET-B/SLIC card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 IPSM IPSHC IS-NR Active ----- ALARM STATUS = No Alarms. IMTPCI GPL version = 133-002-000 BLVXW6 GPL version = 133-002-000 BLDIAG6 GPL version = 133-002-000 BLBEPM GPL version = 133-002-000 BLCPLD GPL version = 133-002-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 32C ( 90F) PEAK TEMPERATURE: = 39C (103F) [06-05-02 13:40] Command Completed.
For an E5-ATM card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 LIMATM ATMHC IS-NR Active ----- ALARM STATUS = No Alarms. IMTPCI GPL version = 133-002-000 BLVXW6 GPL version = 133-002-000 BLDIAG6 GPL version = 133-002-000 BLBEPM GPL version = 133-002-000 BLCPLD GPL version = 133-002-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 38C (101F) PEAK TEMPERATURE: = 38C (101F) [07-11-23 06:10] SIGNALING LINK STATUS SLK PST LS CLLI A IS-NR ls1 ----------- Command Completed.
For an E5-TSM card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 TSM GLSHC IS-NR Active ----- ALARM STATUS = No Alarms. IMTPCI GPL version = 133-002-000 BLVXW6 GPL version = 133-002-000 BLDIAG6 GPL version = 133-002-000 BLBEPM GPL version = 133-002-000 BLCPLD GPL version = 133-002-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 38C (101F) PEAK TEMPERATURE: = 38C (101F) [07-11-23 06:10] Command Completed.
Continue the procedure by performing one of these actions:
GPL
column in the rept-stat-card
output in 2), continue the procedure with 5. GPL
column in the rept-stat-card
output in 2), continue the procedure with 12. GPL
column in the rept-stat-card
output in 2), continue the procedure with 7. GPL
column in the rept-stat-card
output in 2), continue the procedure with 9. GPL
column in the rept-stat-card
output in 2), continue the procedure with 4. GPL
column in the rept-stat-card
output in 2), continue the procedure with 3. rept-stat-card:appl=gls
The output from this command will display the TSMs that are running the GLS GPL and the E5-TSMs that are running the GLSHC GPL.
This is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1207 133-003-000 TSM GLSHC IS-NR Active ----- 1211 133-003-000 TSM GLSHC IS-NR Active ----- 1303 133-003-000 TSM GLSHC IS-NR Active ----- Command Completed.
Continue the procedure with 12.
rept-stat-sccp
command.The output from this command will display the DSMs that are running the VSCCP GPL and the E5-SM4G cards that are running the SCCPHC GPL.
This is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION PST SST AST MSU USAGE CPU USAGE ----------------------------------------------------------------------------- 1303 133-003-000 IS-NR Active ----- 47% 81% 2103 133-003-000 IS-NR Active ----- 34% 50% 2111 133-003-000 IS-NR Active ----- 21% 29% 2115 133-003-000 IS-NR Active ----- 35% 52% 2117 133-003-000 IS-NR Active ----- 40% 71% ----------------------------------------------------------------------------- SCCP Service Average MSU Capacity = 36% Average CPU Capacity = 56% Command Completed.
Note:
Therept-stat-sccp
command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by the rept-stat-sccp
command, refer to the rept-stat-sccp
command description in Commands User's Guide.Continue the procedure with 12.
Enter the rtrv-slk
command with the card location specified in 2. For this example, enter this command.
rtrv-slk:loc=1303
This is an example of the possible output for an HC MIM or E5-E1T1 card.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 L2T PCR PCR E1 E1 LOC LINK LSN SLC TYPE SET BPS ECM N1 N2 LOC PORT TS 1303 A e11303a 0 LIME1 1 64000 PCR 76 3800 1303 2 12 1303 B e11303b 0 LIME1 1 56000 BASIC --- ----- 1303 1 2 1303 A1 e11303a 1 LIME1 1 56000 BASIC --- ----- 1303 1 3 1303 B3 e11303b 1 LIME1 1 56000 BASIC --- ----- 1303 1 7
This is an example of the possible output for an E5-ENET card.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 LOC LINK LSN SLC TYPE IPLIML2 1303 A e11303a 0 IPLIM M2PA 1303 B e11303b 0 IPLIM M2PA 1303 A1 e11303a 1 IPLIM M2PA 1303 B3 e11303b 1 IPLIM M2PA
This is an example of the possible output for an E5-ATM card.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 LP ATM LOC LINK LSN SLC TYPE SET BPS TSEL VCI VPI LL 1303 A ls2 2 LIMATM 1 1544000 LINE 5 0 0 1303 B ls1 3 LIMATM 1 1544000 LINE 5 0 0
dact-slk
command. For this example, enter these commands.
dact-slk:loc=1303:link=a
dact-slk:loc=1303:link=b
dact-slk:loc=1303:link=a1
dact-slk:loc=1303:link=b3
Caution:
These command examples place the signaling links on card 1303 out of service. This will interrupt service on the signaling links on card 1303 and allow the BLIXP GPL to be loaded on to card 1303.Caution:
If the EAGLE contains only signaling links assigned to the card that is specified in this step, deactivating all of the signaling links that are assigned to the card will take all of these signaling links out of service and will isolate the EAGLE from the network.When each of these commands have successfully completed, this message should appear.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Deactivate SLK message sent to card
Continue the procedure with 12.
rept-stat-dlk
command with the card location specified in 2. For this example, enter this command.
rept-stat-dlk:loc=1303
This is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 DLK PST SST AST 1303 IS-NR Active ---- Alarm Status = No Alarms. Command Completed.
canc-dlk
command. For this example, enter this command. canc-dlk:loc=1303
Caution:
This command example places the TCP/IP data link on card 1303 out of service. This will interrupt service on the TCP//IP data link on card 1303 and allow the flash GPL to be loaded onto card 1303.Caution:
If there is only one TCP/IP data link in the EAGLE, placing the card out of service will cause the STPLAN feature to be disabled.When this command has successfully completed, these messages should appear.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Deactivate Link message sent to card. Command Completed.
Continue the procedure with 12.
rtrv-trm
command. The Telnet terminals associated with the card shown in 9 must be taken out of service. The Telnet terminals are shown in the output with the entry TELNET
in the TYPE
field. This is an example of the possible output. In this example, the Telnet terminals that must be taken out of service are terminals 17 to 24.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 TRM TYPE COMM FC TMOUT MXINV DURAL 1 VT320 9600-7-E-1 SW 30 5 99:59:59 2 KSR 9600-7-E-1 HW 30 5 INDEF 3 PRINTER 4800-7-E-1 HW 30 0 00:00:00 4 VT320 2400-7-E-1 BOTH 30 5 00:30:00 5 VT320 9600-7-O-1 NONE 30 5 00:00:30 6 VT320 9600-7-O-1 NONE 30 5 00:00:30 7 PRINTER 9600-7-E–2 HW 30 5 00:30:00 8 KSR 19200-7-E-2 BOTH 30 5 00:30:00 9 VT320 9600-7-O-1 NONE 30 5 00:00:30 10 VT320 9600-7-E-1 HW 30 5 00:30:00 11 VT320 4800-7-E-1 HW 30 5 00:30:00 12 PRINTER 9600-7-E-1 HW 30 4 00:30:00 13 VT320 9600-7-O-1 NONE 30 5 00:30:00 14 VT320 9600-7-E-2 SW 30 8 00:30:00 15 VT320 9600-7-E–2 HW 30 5 00:30:00 16 VT320 9600-7-E-2 BOTH 30 3 00:30:00 TRM TYPE LOC TMOUT MXINV DURAL 17 TELNET 1303 60 5 00:30:00 18 TELNET 1303 60 5 00:30:00 19 TELNET 1303 60 5 00:30:00 20 TELNET 1303 60 5 00:30:00 21 TELNET 1303 60 5 00:30:00 22 TELNET 1303 60 5 00:30:00 23 TELNET 1303 60 5 00:30:00 24 TELNET 1303 60 5 00:30:00 25 TELNET 1203 60 5 00:30:00 26 TELNET 1203 60 5 00:30:00 27 TELNET 1203 60 5 00:30:00 28 TELNET 1203 60 5 00:30:00 39 TELNET 1203 60 5 00:30:00 30 TELNET 1203 60 5 00:30:00 31 TELNET 1203 60 5 00:30:00 32 TELNET 1203 60 5 00:30:00 33 TELNET 1208 60 5 00:30:00 34 TELNET 1208 60 5 00:30:00 35 TELNET 1208 60 5 00:30:00 36 TELNET 1208 60 5 00:30:00 37 TELNET 1208 60 5 00:30:00 38 TELNET 1208 60 5 00:30:00 39 TELNET 1208 60 5 00:30:00 40 TELNET 1208 60 5 00:30:00
Note:
Thertrv-trm
command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by the rtrv-trm
command, see the rtrv-trm
command description in Commands User's Guide. rept-stat-trm
command. This is an example of the possible output. rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 TRM PST SST AST 1 IS-NR Active ----- 2 IS-NR Active ----- 3 IS-NR Active ----- 4 IS-NR Active ----- 5 IS-NR Active ----- 6 IS-NR Active ----- 7 IS-NR Active ----- 8 IS-NR Active ----- 9 IS-NR Active ----- 10 IS-NR Active ----- 11 IS-NR Active ----- 12 IS-NR Active ----- 13 IS-NR Active ----- 14 IS-NR Active ----- 15 IS-NR Active ----- 16 IS-NR Active ----- 17 IS-NR Active ----- 18 IS-NR Active ----- 19 IS-NR Active ----- 20 IS-NR Active ----- 21 IS-NR Active ----- 22 IS-NR Active ----- 23 IS-NR Active ----- 24 IS-NR Active ----- 25 IS-NR Active ----- 26 IS-NR Active ----- 27 IS-NR Active ----- 28 IS-NR Active ----- 29 IS-NR Active ----- 30 IS-NR Active ----- 31 IS-NR Active ----- 32 IS-NR Active ----- 33 IS-NR Active ----- 34 IS-NR Active ----- 35 IS-NR Active ----- 36 IS-NR Active ----- 37 IS-NR Active ----- 38 IS-NR Active ----- 39 IS-NR Active ----- 40 IS-NR Active ----- Command Completed.
rmv-trm
or the inh-trm
command. The function of the rmv-trm
and the inh-trm
commands are the same. For this example, enter these commands. rmv-trm:trm=17
rmv-trm:trm=18
rmv-trm:trm=19
rmv-trm:trm=20
rmv-trm:trm=21
rmv-trm:trm=22
rmv-trm:trm=23
rmv-trm:trm=24
Note:
If the terminal that is being taken out of service is the last in service SEAS terminal, theforce=yes
parameter must be specified with thermv-trm
command for that terminal. Caution:
Placing the Telnet terminals out of service will disable any Telnet sessions running on these terminals.If the status of any of the terminals shown in the PST
field in 10 is OOS-MT-DSBLD (out-of-service maintenance disabled), the terminal is already out of service and the rmv-trm
command does not need to be executed for that terminal.
This message should appear when each of these commands have successfully completed.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Inhibit message sent to terminal rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Command Completed.
rmv-card
or inh-card
command. The function of the rmv-card
and the inh-card
commands are the same.For this example, enter this command.
rmv-card:loc=1303
When this command has successfully completed, this message should appear.
rlghncxa03w 10-12-01 11:11:28 GMT EAGLE5 43.0.0 Card has been inhibited.
force=yes
parameter must be specified in this step if any of these conditions exist.flash-card
command with the code=appr
and the card location parameters. Caution:
Theflash-card
command cannot be entered if the IMT Rate Change sequence or the Extended Bit Error Rate Test (BERT) is being performed. For this example, enter this command.
flash-card:code=appr:loc=1303
When this command has successfully completed, these messages should appear.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Flash Card: Downloading BLIXP on card 1303. ; rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Flash Card: Card 1303 download BLIXP complete. ; rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Flash Card: Activating BLIXP on card 1113. ; rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Flash Card: Card 1303 activation BLIXP complete. ; rrlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Command Completed.
rst-card
or alw-card
command. The function of the rst-card
and the alw-card
commands are the same.The rst-card
or alw-card
command also loads the approved version of the BLIXP GPL onto the card.
For this example, enter this command.
rst-card:code=appr:loc=1303
When this command has successfully completed, this message should appear.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Card has been allowed.
rept-stat-card
command. For this example, enter this command.
rept-stat-card:loc=1303
For an HC MIM or E5-E1T1 card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 LIME1 SS7HC IS-NR Active ----- ALARM STATUS = No Alarms. BLIXP GPL version = 133-003-000 IMT BUS A = Conn IMT BUS B = Conn SIGNALING LINK STATUS SLK PST LS CLLI A OOS-MT-DSBLD e11303a ----------- B OOS-MT-DSBLD e11303b ----------- A1 OOS-MT-DSBLD e11303a ----------- B3 OOS-MT-DSBLD e11303b ----------- Command Completed.
For an E5-E1T1 card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 IPLIM SS7EPM IS-NR Active ----- ALARM STATUS = No Alarms. BLIXP GPL version = 133-003-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 32C ( 90F) [ALARM TEMP: 60C (140F)] PEAK TEMPERATURE: = 39C (103F) [06-05-02 13:40] SIGNALING LINK STATUS SLK PST LS CLLI A IS-NR e11303a ----------- B IS-NR e11303b ----------- A1 IS-NR e11303a ----------- B3 IS-NR e11303b ----------- Command Completed.
For an E5-ENET card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 DCM IPLHC IS-NR Active ----- ALARM STATUS = No Alarms. BLIXP GPL version = 133-003-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 32C ( 90F) [ALARM TEMP: 60C (140F)] PEAK TEMPERATURE: = 39C (103F) [06-05-02 13:40] SIGNALING LINK STATUS SLK PST LS CLLI A IS-NR e11303a ----------- B IS-NR e11303b ----------- A1 IS-NR e11303a ----------- B3 IS-NR e11303b ----------- Command Completed.
For an E5-STC card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 STC ERTHC IS-NR Active ----- ALARM STATUS = No Alarms. BLIXP GPL version = 133-003-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 61C (142F) PEAK TEMPERATURE: = 61C (142F) [06-05-02 13:40] NTP broadcast = VALID STC IP PORT A: OOS-MT Unavail ----- ALARM STATUS = ** 0084 IP Connection Unavailable ERROR STATUS = DHCP Lease. Physical Link. STC IP PORT B: OOS-MT Unavail ----- ALARM STATUS = ** 0084 IP Connection Unavailable ERROR STATUS = DHCP Lease. Physical Link. Command Completed.
For an E5-SLAN card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 DCM SLANHC IS-NR Active ----- ALARM STATUS = No Alarms. BLIXP GPL version = 133-003-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 60C (140F) PEAK TEMPERATURE: = 63C (146F) [00-02-12 21:58] DLK A PST = IS-NR SST = Avail AST = ----- SLAN % EAGLE CAPACITY = 57% SLAN % HOST CAPACITY = 49% Command Completed.
For an E5-SM4G card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 DSM SCCPHC IS-NR Active ----- ALARM STATUS = No Alarms. BLIXP GPL version = 133-003-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 31C ( 88F) PEAK TEMPERATURE: = 32C ( 90F) [07-05-12 15:55] SCCP % OCCUP = 1% Command Completed.
For an E5-ENET-B or SLIC card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 IPSM IPSHC IS-NR Active ----- ALARM STATUS = No Alarms. BLIXP GPL version = 133-003-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 32C ( 90F) PEAK TEMPERATURE: = 39C (103F) [06-05-02 13:40] Command Completed.
For an E5-ATM card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 LIMATM ATMHC IS-NR Active ----- ALARM STATUS = No Alarms. BLIXP GPL version = 133-003-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 38C (101F) PEAK TEMPERATURE: = 38C (101F) [07-11-23 06:10] SIGNALING LINK STATUS SLK PST LS CLLI A IS-NR ls1 ----------- Command Completed.
For an E5-TSM card, this is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 1303 133-003-000 TSM GLSHC IS-NR Active ----- ALARM STATUS = No Alarms. BLIXP GPL version = 133-003-000 IMT BUS A = Conn IMT BUS B = Conn CURRENT TEMPERATURE = 38C (101F) PEAK TEMPERATURE: = 38C (101F) [07-11-23 06:10] Command Completed.
Note:
If the version number of the BLIXP GPL that is shown in this step is not the version specified in 1, contact the Customer Care Center. Refer to the My Oracle Support (MOS) section for the contact information.Continue the procedure by performing one of these actions.
GPL
column in the rept-stat-card
output in 15), continue the procedure with 16. GPL
column in the rept-stat-card
output in 15), continue the procedure with 22. GPL
column in the rept-stat-card
output in 15), continue the procedure with 18. GPL
column in the rept-stat-card
output in 15), continue the procedure with 20. act-slk
command. For this example, enter these commands.
act-slk:loc=1303:link=a
act-slk:loc=1303:link=b
act-slk:loc=1303:link=a1
act-slk:loc=1303:link=b3
When each of these commands have successfully completed, this message should appear.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Activate SLK message sent to card
rept-stat-slk
command with the card location and signaling link. For this example, enter these commands.
rept-stat-slk:loc=1303:link=a
This is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 SLK LSN CLLI PST SST AST 1303,A e11303a ----------- IS-NR Avail ---- ALARM STATUS = No Alarms. UNAVAIL REASON = --
rept-stat-slk:loc=1303:link=b
This is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 SLK LSN CLLI PST SST AST 1303,B e11303b ----------- IS-NR Avail ---- ALARM STATUS = No Alarms. UNAVAIL REASON = --
rept-stat-slk:loc=1303:link=a1
This is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 SLK LSN CLLI PST SST AST 1303,A1 e11303a ----------- IS-NR Avail ---- ALARM STATUS = No Alarms. UNAVAIL REASON = --
rept-stat-slk:loc=1303:link=b3
This is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 SLK LSN CLLI PST SST AST 1303,B3 e11303b ----------- IS-NR Avail ---- ALARM STATUS = No Alarms. UNAVAIL REASON = -- Command Completed.
Continue the procedure with 22.
act-dlk
command. For this example, enter this command. act-dlk:loc=1303
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Activate Link message sent to card.
rept-stat-dlk
command. For this example, enter this command. rept-stat-dlk:loc=1303
This is an example of the possible output.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 DLK PST SST AST 1303 IS-NR Active ---- Alarm Status = No Alarms. Command Completed.
Continue the procedure with 22.
rst-trm
or alw-trm
command. The function of the rst-trm
and the alw-trm
commands are the save. For this example, enter these commands. rst-trm:trm=17
rst-trm:trm=18
rst-trm:trm=19
rst-trm:trm=20
rst-trm:trm=21
rst-trm:trm=22
rst-trm:trm=23
rst-trm:trm=24
This message should appear when each of these commands have successfully completed.
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Allow message sent to terminal rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 Command Completed.
rept-stat-trm
command. This is an example of the possible output. rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 TRM PST SST AST 1 IS-NR Active ----- 2 IS-NR Active ----- 3 IS-NR Active ----- 4 IS-NR Active ----- 5 IS-NR Active ----- 6 IS-NR Active ----- 7 IS-NR Active ----- 8 IS-NR Active ----- 9 IS-NR Active ----- 10 IS-NR Active ----- 11 IS-NR Active ----- 12 IS-NR Active ----- 13 IS-NR Active ----- 14 IS-NR Active ----- 15 IS-NR Active ----- 16 IS-NR Active ----- 17 IS-NR Active ----- 18 IS-NR Active ----- 19 IS-NR Active ----- 20 IS-NR Active ----- 21 IS-NR Active ----- 22 IS-NR Active ----- 23 IS-NR Active ----- 24 IS-NR Active ----- 25 IS-NR Active ----- 26 IS-NR Active ----- 27 IS-NR Active ----- 28 IS-NR Active ----- 29 IS-NR Active ----- 30 IS-NR Active ----- 31 IS-NR Active ----- 32 IS-NR Active ----- 33 IS-NR Active ----- 34 IS-NR Active ----- 35 IS-NR Active ----- 36 IS-NR Active ----- 37 IS-NR Active ----- 38 IS-NR Active ----- 39 IS-NR Active ----- 40 IS-NR Active ----- Command Completed.
Figure 3-9 Updating a High-Capacity Card to Run the BLIXP GPL
Sheet 1 of 4
Sheet 2 of 4
Sheet 3 of 4
Sheet 4 of 4