IPv6 Address Configuration

This section calls out the configurations and parameters for which you can enter IPv6 addresses. In this first IPv6 implementation, the complete range of system configurations and their parameters are available for IPv6 use.

The Oracle® Enterprise Session Border Controller follows RFC 3513 its definition of IPv6 address representations. Quoting from that RFC, these are the two forms supported:

  • The preferred form is x:x:x:x:x:x:x:x, where the 'x's are the hexadecimal values of the eight 16-bit pieces of the address. Examples:

FEDC:BA98:7654:3210:FEDC:BA98:7654:3210

1080:0:0:0:8:800:200C:417A

Note that it is not necessary to write the leading zeros in an individual field, but there must be at least one numeral in every field (except for the case described in 2.).

  • Due to some methods of allocating certain styles of IPv6 addresses, it will be common for addresses to contain long strings of zero bits. In order to make writing addresses containing zero bits easier a special syntax is available to compress the zeros. The use of "::" indicates one or more groups of 16 bits of zeros. The "::" can only appear once in an address. The "::" can also be used to compress leading or trailing zeros in an address. For example, the following addresses: 1080:0:0:0:8:800:200C:417A a unicast address FF01:0:0:0:0:0:0:101 a multicast address

    0:0:0:0:0:0:0:1 the loopback address

    0:0:0:0:0:0:0:0 the unspecified addresses

    may be represented as:

    1080::8:800:200C:417A a unicast address

    FF01::101 a multicast address

    ::1 the loopback address

    :: the unspecified addresses

Note:

For ACLI parameters that support only IPv4, there are many references to that version as the accepted value for a configuration parameter or other IPv4-specific languages. For IPv6 support, these references have been edited. For example, rather than providing help that refers specifically to IPv4 addresses when explaining what values are accepted in an ACLI configuration parameter, you will now see an <ipAddr> note.

Access Control

These are the IPv6-enabled parameters in the access-control configuration.

Parameter Entry Format
source-address <ip-address>[/<num-bits>][:<port>[/<port-bits>]]
destination-address <ip-address>[/<num-bits>][:<port>[/<port-bits>]]

Host Route

These are the IPv6-enabled parameters in the host-route configuration.

Parameter Entry Format
dest-network <ipv4> | <ipv6>
netmask <ipv4> | <ipv6>
gateway <ipv4> | <ipv6>

Local Policy

These are the IPv6-enabled parameters in the local-policy configuration.

Parameter Entry Format
from-address <ipv4> | <ipv6> | POTS Number, E.164 Number, hostname, wildcard
to-address <ipv4> | <ipv6> | POTS Number, E.164 Number, hostname, wildcard

Network Interface

These are the IPv6-enabled parameters in the network-interface configuration.

Parameter Entry Format
hostname <ipv4> | <ipv6> | hostname
ip-address <ipv4> | <ipv6>
pri-utility-addr <ipv4> | <ipv6>
sec-utility-addr <ipv4> | <ipv6>
netmask <ipv4> | <ipv6>
gateway <ipv4> | <ipv6>
sec-gateway <ipv4> | <ipv6>
dns-ip-primary <ipv4> | <ipv6>
dns-ip-backup1 <ipv4> | <ipv6>
dns-ip-backup2 <ipv4> | <ipv6>
add-hip-ip <ipv4> | <ipv6>
remove-hip-ip <ipv4> | <ipv6>
add-icmp-ip <ipv4> | <ipv6>
remove-icmp-ip <ipv4> | <ipv6>

ENUM Server

These are the IPv6-enabled parameters in the enum-config.

Parameter Entry Format
enum-servers [<ipv4> | <ipv6>]:port

Realm Configuration

These are the IPv6-enabled parameters in the realm-config.

Parameter Entry Format
addr-prefix [<ipv4> | <ipv6>]/prefix

Session Agent

These are the IPv6-enabled parameters in the session-agent configuration.

Parameter Entry Format
hostname <ipv4> | <ipv6>
ip-address <ipv4> | <ipv6>

SIP Configuration

These are the IPv6-enabled parameters in the session-config.

Parameter Entry Format
registrar-host <ipv4> | <ipv6> | hostname | *

SIP Interface SIP Ports

These are the IPv6-enabled parameters in the sip-interface>sip-ports configuration.

Parameter Entry Format
address <ipv4> | <ipv6>

Steering Pool

These are the IPv6-enabled parameters in the steering-pool configuration.

Parameter Entry Format
ip-address <ipv4> | <ipv6>

System Configuration

These are the IPv6-enabled parameters in the system-config.

Parameter Entry Format
default-v6-gateway <ipv6>

TSCF Configuration

These are the IPv6-enabled parameters in the TSCF > tscf-address-pool > address-range > network-address.

Parameter Entry Format
network-address <ipv4> | <ipv6