- Database Administration - IP7 User's Guide
- IPSG M2PA and M3UA Configuration Procedures
- Changing the SCTP Checksum Algorithm Option for IPSG M2PA Associations
Changing the SCTP Checksum Algorithm Option for IPSG M2PA Associations
Use this procedure to change the SCTP checksum algorithm, either Adler-32 or CRC-32c, applied to traffic on SCTP associations. The
sctpcsum parameter of the chg-sg-opts command is used to change this option. The Adler-32 and CRC-32c checksum algorithms specified in this procedure applies to all the M2PA associations that are assigned to all the IP cards running the IPSG application. This option is a system-wide option. To apply this option to associations assigned to cards running the IPLIM, IPLIMI, SS7IPGW, or IPGWI applications, or to IPSG M3UA associations, perform these procedures.
The sctpcsum parameter contains another value, percard, that allows either the Adler-32 or CRC-32c SCTP checksum algorithm to be specified for the all the associations assigned to a specific card. With this option specified, the Adler-32 checksum algorithm can be specified for the associations on one card and the CRC-32c checksum algorithm can be specified for the associations on another card. Setting the sctpcsum parameter to percard changes the SCTP checksum algorithm for the associations assigned to a card to the SCTP checksum algorithm value for that card. The checksum algorithm for individual cards is provisioned by performing the Configuring an IP Link procedure.
Once the SCTP checksum option has been changed, the associations on each IP card need to be reset by changing the open parameter value for each association to no, then back to yes. This ensures that the associations on the IP card are using the new SCTP checksum algorithm.
Canceling the RTRV-ASSOC Command
Because the rtrv-assoc command used in this procedure can output information for a long period of time, the rtrv-assoc command can be canceled and the output to the terminal stopped. There are three ways that the rtrv-assoc command can be canceled.
- Press the
F9function key on the keyboard at the terminal where thertrv-assoccommand was entered. - Enter the
canc-cmdwithout thetrmparameter at the terminal where thertrv-assoccommand was entered. - Enter the
canc-cmd:trm=<xx>, where<xx>is the terminal where thertrv-assoccommand was entered, from another terminal other that the terminal where thertrv-assoccommand was entered. To enter thecanc-cmd:trm=<xx>command, the terminal must allow Security Administration commands to be entered from it and the user must be allowed to enter Security Administration commands. The terminal’s permissions can be verified with thertrv-secu-trmcommand. The user’s permissions can be verified with thertrv-userorrtrv-secu-usercommands.
For more information about the canc-cmd command, go to Commands User's Guide.
- Display the current IP options in the database by entering the
rtrv-sg-optscommand. The following is an example of the possible output.rlghncxa03w 06-10-28 21:16:37 GMT EAGLE5 36.0.0 SCTPCSUM: adler32The
rtrv-sg-optscommand output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by thertrv-sg-optscommand, see thertrv-sg-optscommand description in Commands User's Guide. - Display the cards in the EAGLE by entering the
rtrv-cardcommand. This is an example of the possible output.rlghncxa03w 09-10-15 16:34:56 GMT EAGLE5 41.0.0 CARD TYPE APPL LSET NAME LINK SLC LSET NAME LINK SLC 1101 DSM VSCCP 1102 TSM GLS 1104 DCM STPLAN 1113 GSPM EOAM 1114 TDM-A 1115 GSPM EOAM 1116 TDM-B 1117 MDAL 1201 LIMDS0 SS7ANSI lsn1 A 0 lsn2 B 1 1202 DCM IPLIM ipnode2 A 1 1203 LIMDS0 SS7ANSI lsn2 A 0 lsn1 B 1 1204 LIMATM ATMANSI atmgwy A 0 1205 DCM IPLIM ipnode1 A 0 ipnode3 B 1 1207 DCM IPLIM ipnode2 A 0 1303 DCM IPLIM ipnode3 A 0 ipnode1 B 1 1305 DCM IPLIM ipnode4 A 0 1308 ENET IPSG ipnode3 B 2 ipnode1 A1 2 ipnode4 B2 1 1315 DCM SS7IPGW ipgtwy1 A 1317 DCM IPGWI ipgtwy2 ARecord the card location, shown in the
LOCcolumn, and signaling link, shown in theLINKcolumn, information for all cards running the IPSG application. - Select one of the IPSG cards shown in 2. Display the associations assigned to the IPSG card by entering the r
rtrv-assoccommand and specifying the card location of the IPSG card. For this example, enter this command.rtrv-assoc:loc=1308The following is an example of the possible output.
rlghncxa03w 08-04-28 09:12:36 GMT EAGLE5 38.0.0 CARD IPLNK ANAME LOC PORT LINK ADAPTER LPORT RPORT OPEN ALW assoc2 1308 A A1 M2PA 2187 1025 YES YES assoc4 1308 A B M2PA 3290 1025 YES YES assoc5 1308 A B2 M2PA 1057 1025 YES YES IP Appl Sock/Assoc table is (9 of 4000) 1% full Assoc Buffer Space Used (600 KB of 3200 KB) on LOC = 1308If the
ADAPTERvalue of the associations shown in thertrv-assocoutput isM2PA, continue the procedure with 4.If the
ADAPTERvalue of the associations shown in thertrv-assocoutput isM3UA, do not perform the remainder of this procedure. Perform the Changing the SCTP Checksum Algorithm Option for IPSG M3UA Associations procedure to change the SCTP checksum algorithm for IPSG M3UA associations. - Change the SCTP checksum option in the database using the
chg-sg-optscommand. For this example, enter this command.chg-sg-opts:sctpcsum=crc32cWhen this command has successfully completed, the following message should appear.
rlghncxa03w 06-10-28 21:19:37 GMT EAGLE5 36.0.0 CHG-SG-OPTS: MASP A - COMPLTDContinue the procedure by performing one of these actions.- If the
sctpcsumparameter value was changed to eitheradler32orcrc32c, continue the procedure with 5. - If the
sctpcsumparameter value was changed topercard, perform the Configuring an IP Card procedure to assign an sctpcsum parameter value to all the cards containing IPSG M2PA associations. After the Configuring an IP Card procedure has been performed, continue the procedure with 6.
- If the
- Verify that the SCTP checksum algorithm was changed using the
rtrv-sg-optscommand. The SCTP checksum algorithm option value is shown in theSCTPCSUMparameter. The following is an example of the possible output.rlghncxa03w 06-10-28 21:16:37 GMT EAGLE5 36.0.0 SCTPCSUM: crc32cThe
rtrv-sg-optscommand output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by thertrv-sg-optscommand, see thertrv-sg-optscommand description in Commands User's Guide. - Place the signaling links assigned to the IPSG card out of service using the
dact-slkcommand, specifying theLOCandLINKvalues shown in 3. For this example, enter these commands.dact-slk:loc=1308:link=a1dact-slk:loc=1308:link=bdact-slk:loc=1308:link=b2When these commands have successfully completed, this message appears.
rlghncxa03w 06-10-12 09:12:36 GMT EAGLE5 36.0.0 Deactivate Link message sent to card - Change the value of the
openparameter of the associations shown in 3 tonoby specifying thechg-assoccommand with theopen=noparameter. For this example, enter this command.chg-assoc:aname=assoc2:open=nochg-assoc:aname=assoc4:open=nochg-assoc:aname=assoc5:open=noWhen this command has successfully completed, this message should appear.
rlghncxa03w 06-10-28 09:12:36 GMT EAGLE5 36.0.0 CHG-ASSOC: MASP A - COMPLTD; - Change the value of the
openparameter of the associations changed in 7 toyesby specifying thechg-assoccommand with theopen=yesparameter. For this example, enter this command.chg-assoc:aname=assoc2:open=yeschg-assoc:aname=assoc4:open=yeschg-assoc:aname=assoc5:open=yesWhen this command has successfully completed, this message should appear.
rlghncxa03w 06-10-28 09:12:36 GMT EAGLE5 36.0.0 CHG-ASSOC: MASP A - COMPLTD; - Verify the checksum algorithm that is assigned to the associations shown in 8 by entering the
sctp -apass command with the card location of the IP card specified in 6 and the name of the associations specified in 8. For this example, enter this command.pass:loc=1308:cmd=”sctp -a assoc2 ”The following is an example of the possible output.
rlghncxa03w 10-12-28 21:16:37 GMT EAGLE5 43.0.0 Aname Local Local Primary Remote IP Address Port Address Port assoc2 192.1.1.24 2187 192.168.112.4 1025 192.1.1.24 Configuration State Retransmission Mode = LIN State = OPEN Min. Retransmission Timeout = 10000 ULP association id = 18 Max. Retransmission Timeout = 800000 Number of nets = 2 Max. Number of Retries = 10 Inbound Streams = 1 Min. Congestion Window = 3000 Outbound Streams = 2 Inbound Streams = 2 Outbound Streams = 2 Checksum Algorithm = crc32c Send/Rcv Buffer Size = 204800 Nets Data IP Address 192.168.112.4 State Reachable Port 1025 Primary YES MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 IP Address 192.168.112.5 State Reachable Port 7777 Primary NO MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 Last Net Sent To = 192.168.112.4 Last Net Rcvd From = 192.168.112.4 Over All Eror Count = 0 Peers Rwnd = 13880 My Rwnd = 16384 Max Window = 16384 Initial Seq Number = 24130 Next Sending Seq Number = 124686 Last Acked Seq Number = 124669 Maximum Outbound Char Count = 16384 Current Outbound Char Count = 2112 Number Unsent Char Count = 0 Outbound Data Chunk Count = 16 Number Unsent = 0 Number To Retransmit = 0 ip datagrams rcvd = 155402 ip datagrams with data chunks rcvd = 120844 data chunks rcvd = 367908 data chunks read = 367900 dup tsns rcvd = 8 sacks rcvd = 38734 gap ack blocks rcvd = 3 heartbeat requests rcvd = 135 heartbeat acks rcvd = 52 heartbeat requests sent = 52 ip datagrams sent = 129254 ip datagrams with data chunks sent = 73084 data chunks sent = 396330 retransmit data chunks sent = 135 sacks sent = 64872 send failed = 0 retransmit timer count = 0 consecutive retransmit timeouts = 0 RTT between RMIN and RMAX inclusive = 6 RTT greater than RMAX = 0 fast retransmit count = 135 recv timer count = 0 heartbeat timer count = 244 none left tosend = 0 none left rwnd gate = 5 none left cwnd gate = 8 ; rlghncxa03w 10-12-28 21:16:37 GMT EAGLE5 43.0.0 SCTP command completerlghncxa03w 08-04-28 21:16:37 GMT EAGLE5 38.0.0 Aname Local Local Primary Remote IP Address Port Address Port assoc2 192.1.1.24 2187 192.168.112.4 1025 192.1.1.24 Configuration State Retransmission Mode = LIN State = OPEN Min. Retransmission Timeout = 10 ULP association id = 18 Max. Retransmission Timeout = 800 Number of nets = 2 Max. Number of Retries = 10 Inbound Streams = 1 Min. Congestion Window = 3000 Outbound Streams = 2 Inbound Streams = 2 Outbound Streams = 2 Checksum Algorithm = crc32c Nets Data IP Address 192.168.112.4 State Reachable Port 1025 Primary YES MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 IP Address 192.168.112.5 State Reachable Port 7777 Primary NO MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 Last Net Sent To = 192.168.112.4 Last Net Rcvd From = 192.168.112.4 Over All Eror Count = 0 Peers Rwnd = 13880 My Rwnd = 16384 Max Window = 16384 Initial Seq Number = 24130 Next Sending Seq Number = 124686 Last Acked Seq Number = 124669 Maximum Outbound Char Count = 16384 Current Outbound Char Count = 2112 Number Unsent Char Count = 0 Outbound Data Chunk Count = 16 Number Unsent = 0 Number To Retransmit = 0 ip datagrams rcvd = 155402 ip datagrams with data chunks rcvd = 120844 data chunks rcvd = 367908 data chunks read = 367900 dup tsns rcvd = 8 sacks rcvd = 38734 gap ack blocks rcvd = 3 heartbeat requests rcvd = 135 heartbeat acks rcvd = 52 heartbeat requests sent = 52 ip datagrams sent = 129254 ip datagrams with data chunks sent = 73084 data chunks sent = 396330 retransmit data chunks sent = 135 sacks sent = 64872 send failed = 0 retransmit timer count = 0 consecutive retransmit timeouts = 0 RTT between RMIN and RMAX inclusive = 6 RTT greater than RMAX = 0 fast retransmit count = 135 recv timer count = 0 heartbeat timer count = 244 none left tosend = 0 none left rwnd gate = 5 none left cwnd gate = 8 ; rlghncxa03w 08-04-28 21:16:37 GMT EAGLE5 38.0.0 SCTP command completepass:loc=1308:cmd=”sctp -a assoc4 ”The following is an example of the possible output.
rlghncxa03w 10-12-28 21:16:37 GMT EAGLE5 43.0.0 Aname Local Local Primary Remote IP Address Port Address Port assoc4 192.1.1.24 3290 192.168.112.4 1025 192.1.1.24 Configuration State Retransmission Mode = LIN State = OPEN Min. Retransmission Timeout = 10000 ULP association id = 18 Max. Retransmission Timeout = 800000 Number of nets = 2 Max. Number of Retries = 10 Inbound Streams = 1 Min. Congestion Window = 3000 Outbound Streams = 2 Inbound Streams = 2 Outbound Streams = 2 Checksum Algorithm = crc32c Send/Rcv Buffer Size = 204800 Nets Data IP Address 192.168.112.4 State Reachable Port 1025 Primary YES MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 IP Address 192.168.112.5 State Reachable Port 7777 Primary NO MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 Last Net Sent To = 192.168.112.4 Last Net Rcvd From = 192.168.112.4 Over All Eror Count = 0 Peers Rwnd = 13880 My Rwnd = 16384 Max Window = 16384 Initial Seq Number = 24130 Next Sending Seq Number = 124686 Last Acked Seq Number = 124669 Maximum Outbound Char Count = 16384 Current Outbound Char Count = 2112 Number Unsent Char Count = 0 Outbound Data Chunk Count = 16 Number Unsent = 0 Number To Retransmit = 0 ip datagrams rcvd = 155402 ip datagrams with data chunks rcvd = 120844 data chunks rcvd = 367908 data chunks read = 367900 dup tsns rcvd = 8 sacks rcvd = 38734 gap ack blocks rcvd = 3 heartbeat requests rcvd = 135 heartbeat acks rcvd = 52 heartbeat requests sent = 52 ip datagrams sent = 129254 ip datagrams with data chunks sent = 73084 data chunks sent = 396330 retransmit data chunks sent = 135 sacks sent = 64872 send failed = 0 retransmit timer count = 0 consecutive retransmit timeouts = 0 RTT between RMIN and RMAX inclusive = 6 RTT greater than RMAX = 0 fast retransmit count = 135 recv timer count = 0 heartbeat timer count = 244 none left tosend = 0 none left rwnd gate = 5 none left cwnd gate = 8 ; rlghncxa03w 10-12-28 21:16:37 GMT EAGLE5 43.0.0 SCTP command completerlghncxa03w 08-04-28 21:16:37 GMT EAGLE5 38.0.0 Aname Local Local Primary Remote IP Address Port Address Port assoc4 192.1.1.24 3290 192.168.112.4 1025 192.1.1.24 Configuration State Retransmission Mode = LIN State = OPEN Min. Retransmission Timeout = 10 ULP association id = 18 Max. Retransmission Timeout = 800 Number of nets = 2 Max. Number of Retries = 10 Inbound Streams = 1 Min. Congestion Window = 3000 Outbound Streams = 2 Inbound Streams = 2 Outbound Streams = 2 Checksum Algorithm = crc32c Nets Data IP Address 192.168.112.4 State Reachable Port 1025 Primary YES MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 IP Address 192.168.112.5 State Reachable Port 7777 Primary NO MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 Last Net Sent To = 192.168.112.4 Last Net Rcvd From = 192.168.112.4 Over All Eror Count = 0 Peers Rwnd = 13880 My Rwnd = 16384 Max Window = 16384 Initial Seq Number = 24130 Next Sending Seq Number = 124686 Last Acked Seq Number = 124669 Maximum Outbound Char Count = 16384 Current Outbound Char Count = 2112 Number Unsent Char Count = 0 Outbound Data Chunk Count = 16 Number Unsent = 0 Number To Retransmit = 0 ip datagrams rcvd = 155402 ip datagrams with data chunks rcvd = 120844 data chunks rcvd = 367908 data chunks read = 367900 dup tsns rcvd = 8 sacks rcvd = 38734 gap ack blocks rcvd = 3 heartbeat requests rcvd = 135 heartbeat acks rcvd = 52 heartbeat requests sent = 52 ip datagrams sent = 129254 ip datagrams with data chunks sent = 73084 data chunks sent = 396330 retransmit data chunks sent = 135 sacks sent = 64872 send failed = 0 retransmit timer count = 0 consecutive retransmit timeouts = 0 RTT between RMIN and RMAX inclusive = 6 RTT greater than RMAX = 0 fast retransmit count = 135 recv timer count = 0 heartbeat timer count = 244 none left tosend = 0 none left rwnd gate = 5 none left cwnd gate = 8 ; rlghncxa03w 08-04-28 21:16:37 GMT EAGLE5 38.0.0 SCTP command completepass:loc=1308:cmd=”sctp -a assoc5 ”The following is an example of the possible output.
rlghncxa03w 10-12-28 21:16:37 GMT EAGLE5 43.0.0 Aname Local Local Primary Remote IP Address Port Address Port assoc5 192.1.1.24 1057 192.168.112.4 1025 192.1.1.24 Configuration State Retransmission Mode = LIN State = OPEN Min. Retransmission Timeout = 10000 ULP association id = 18 Max. Retransmission Timeout = 800000 Number of nets = 2 Max. Number of Retries = 10 Inbound Streams = 1 Min. Congestion Window = 3000 Outbound Streams = 2 Inbound Streams = 2 Outbound Streams = 2 Checksum Algorithm = crc32c Send/Rcv Buffer Size = 204800 Nets Data IP Address 192.168.112.4 State Reachable Port 1025 Primary YES MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 IP Address 192.168.112.5 State Reachable Port 7777 Primary NO MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 Last Net Sent To = 192.168.112.4 Last Net Rcvd From = 192.168.112.4 Over All Eror Count = 0 Peers Rwnd = 13880 My Rwnd = 16384 Max Window = 16384 Initial Seq Number = 24130 Next Sending Seq Number = 124686 Last Acked Seq Number = 124669 Maximum Outbound Char Count = 16384 Current Outbound Char Count = 2112 Number Unsent Char Count = 0 Outbound Data Chunk Count = 16 Number Unsent = 0 Number To Retransmit = 0 ip datagrams rcvd = 155402 ip datagrams with data chunks rcvd = 120844 data chunks rcvd = 367908 data chunks read = 367900 dup tsns rcvd = 8 sacks rcvd = 38734 gap ack blocks rcvd = 3 heartbeat requests rcvd = 135 heartbeat acks rcvd = 52 heartbeat requests sent = 52 ip datagrams sent = 129254 ip datagrams with data chunks sent = 73084 data chunks sent = 396330 retransmit data chunks sent = 135 sacks sent = 64872 send failed = 0 retransmit timer count = 0 consecutive retransmit timeouts = 0 RTT between RMIN and RMAX inclusive = 6 RTT greater than RMAX = 0 fast retransmit count = 135 recv timer count = 0 heartbeat timer count = 244 none left tosend = 0 none left rwnd gate = 5 none left cwnd gate = 8 ; rlghncxa03w 10-12-28 21:16:37 GMT EAGLE5 43.0.0 SCTP command completerlghncxa03w 08-04-28 21:16:37 GMT EAGLE5 38.0.0 Aname Local Local Primary Remote IP Address Port Address Port assoc5 192.1.1.24 1057 192.168.112.4 1025 192.1.1.24 Configuration State Retransmission Mode = LIN State = OPEN Min. Retransmission Timeout = 10 ULP association id = 18 Max. Retransmission Timeout = 800 Number of nets = 2 Max. Number of Retries = 10 Inbound Streams = 1 Min. Congestion Window = 3000 Outbound Streams = 2 Inbound Streams = 2 Outbound Streams = 2 Checksum Algorithm = crc32c Nets Data IP Address 192.168.112.4 State Reachable Port 1025 Primary YES MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 IP Address 192.168.112.5 State Reachable Port 7777 Primary NO MTU 1500 cwnd 16384 ssthresh 16384 RTO 120 Last Net Sent To = 192.168.112.4 Last Net Rcvd From = 192.168.112.4 Over All Eror Count = 0 Peers Rwnd = 13880 My Rwnd = 16384 Max Window = 16384 Initial Seq Number = 24130 Next Sending Seq Number = 124686 Last Acked Seq Number = 124669 Maximum Outbound Char Count = 16384 Current Outbound Char Count = 2112 Number Unsent Char Count = 0 Outbound Data Chunk Count = 16 Number Unsent = 0 Number To Retransmit = 0 ip datagrams rcvd = 155402 ip datagrams with data chunks rcvd = 120844 data chunks rcvd = 367908 data chunks read = 367900 dup tsns rcvd = 8 sacks rcvd = 38734 gap ack blocks rcvd = 3 heartbeat requests rcvd = 135 heartbeat acks rcvd = 52 heartbeat requests sent = 52 ip datagrams sent = 129254 ip datagrams with data chunks sent = 73084 data chunks sent = 396330 retransmit data chunks sent = 135 sacks sent = 64872 send failed = 0 retransmit timer count = 0 consecutive retransmit timeouts = 0 RTT between RMIN and RMAX inclusive = 6 RTT greater than RMAX = 0 fast retransmit count = 135 recv timer count = 0 heartbeat timer count = 244 none left tosend = 0 none left rwnd gate = 5 none left cwnd gate = 8 ; rlghncxa03w 08-04-28 21:16:37 GMT EAGLE5 38.0.0 SCTP command completeIf the checksum algorithm shown in any of the associations displayed in this step do not match the checksum algorithm specified in 4, contact the Customer Care Center. Refer to My Oracle Support (MOS) for the contact information.
If the checksum algorithm shown in all of the associations displayed in this step match the checksum algorithm specified in 4, continue the procedure with 10.
- Put the signaling links that were placed out of service in 6 back into service using the
act-slkcommand. For example, enter this command.act-slk:loc=1308:link=a1act-slk:loc=1308:link=bact-slk:loc=1308:link=b2When these commands have successfully completed, this message appears.
rlghncxa03w 06-10-07 11:11:28 GMT EAGLE5 36.0.0 Activate Link message sent to card - Verify the in-service normal (IS-NR) status of the signaling link by using the
rept-stat-slkcommand and specifying the card location and link values specified in 10.For example, enter these commands.
rept-stat-slk:loc=1308:link=a1This message should appear.
rlghncxa03w 06-10-28 21:16:37 GMT EAGLE5 36.0.0 SLK LSN CLLI PST SST AST 1308,A1 ipnode1 ----------- IS-NR Avail ---- Command Completed.rept-stat-slk:loc=1308:link=bThis message should appear.
rlghncxa03w 06-10-28 21:16:37 GMT EAGLE5 36.0.0 SLK LSN CLLI PST SST AST 1308,B ipnode3 ----------- IS-NR Avail ---- Command Completed.rept-stat-slk:loc=1308:link=b2This message should appear.
rlghncxa03w 06-10-28 21:16:37 GMT EAGLE5 36.0.0 SLK LSN CLLI PST SST AST 1308,B2 ipnode4 ----------- IS-NR Avail ---- Command Completed. - Enter the
netstat -p sctppass command with the card location of the IP card to determine if any errors have occurred. For this example, enter this command.pass:loc=1308:cmd=”netstat -p sctp”The following is an example of the possible output.
rlghncxa03w 08-04-28 21:16:37 GMT EAGLE5 38.0.0 ip packets sent...................................... 1474882 ip packets sent with data chunk.................. 306354 control chunks (excluding retransmissions)....... 1172759 ordered data chunks (excluding retransmissions).. 1534350 unordered data chunks (excluding retransmissions) 0 user messages fragmented due to MTU.............. 0 retransmit data chunks sent...................... 4 sacks sent....................................... 496302 send failed...................................... 0 ip packets received.................................. 1816035 ip packets received with data chunk.............. 989957 control chunks (excluding duplicates)............ 833141 ordered data chunks (excluding duplicates)....... 989968 unordered data chunks (excluding duplicates)..... 0 user messages reassembled........................ 0 data chunks read................................. 988601 duplicate tsns received.......................... 0 sacks received................................... 153763 gap ack blocks received.......................... 0 out of the blue.................................. 4 with invalid checksum............................ 0 connections established.............................. 2954 by upper layer................................... 0 by remote endpoint............................... 2958 connections terminated............................... 4 ungracefully..................................... 2952 gracefully....................................... 0 associations dropped due to retransmits.............. 0 consecutive retransmit timeouts...................... 4 retransmit timer count............................... 6 fast retransmit count................................ 0 heartbeat requests received.......................... 330275 heartbeat acks received.............................. 340239 heartbeat requests sent.............................. 340258 associations supported............................... 50 milliseconds cookie life at 4-way start-up handshake. 5000 retransmission attempts allowed at start-up phase.... 8 ; rlghncxa03w 08-04-28 21:16:37 GMT EAGLE5 38.0.0 NETSTAT command completeIf errors are shown in the pass command output, contact the Customer Care Center. Refer to My Oracle Support (MOS) for the contact information.
- Repeat 6 through 12 to update the other IPSG cards in the EAGLE that contain IPSG M2PA associations with the new SCTP checksum algorithm.
- Back up the database by entering the
chg-db:action=backup:dest=fixedcommand. These messages should appear, the active Maintenance and Administration Subsystem Processor (MASP) appears first.BACKUP (FIXED) : MASP A - Backup starts on active MASP. BACKUP (FIXED) : MASP A - Backup on active MASP to fixed disk complete. BACKUP (FIXED) : MASP A - Backup starts on standby MASP. BACKUP (FIXED) : MASP A - Backup on standby MASP to fixed disk complete. - If the
rtrv-cardoutput in 2 shows cards running the SS7IPGW or IPGWI applications, perform the Changing the SCTP Checksum Algorithm Option for M3UA and SUA Associations procedure.If the
rtrv-cardoutput in 2 shows cards running the IPLIM or IPLIMI applications, perform the Changing the SCTP Checksum Algorithm Option for M2PA Associations procedure.If the
rtrv-cardoutput in 2 shows that there are no cards running theSS7IPGW,IPGWI,IPLIM, orIPLIMIapplications, this procedure is finished.
Figure 6-31 Changing the SCTP Checksum Algorithm Option for IPSG M2PA Associations
Sheet 1 of 3
Sheet 2 of 3
Sheet 3 of 3