Oracle® Communications EAGLE Database Administration - SS7 User's Guide Release 46.7 E97335 Revision 1 |
|
![]() Previous |
![]() Next |
There are two types of unsolicited messages that are generated, alarm messages (UAMs) and information messages (UIMs).
Link Unavailability UAMs
The signaling link UAM format includes a CLASS output. This identifies the corresponding link as either an MTP2 or SAAL link class (the SAAL link class is used for high-speed signaling links).
Example:
0044.0200 SLK 1201,A sp1 RCVRY-LKF: link available SLC=01 FECLLI=A1234567890 CLASS=SAAL 0044.0200 SLK 1202,A sp2 RCVRY-LKF: link available SLC=01 FECLLI=A1234567890 CLASS=MTP2
Table C-3 provides a summary of high-speed signaling link and low-speed signaling link unavailable reasons listed from highest priority to lowest.
Table C-7 shows the UAMs that correspond link failures on an high-speed signaling link. All signaling link alarms have a severity level of major, except for UAM 200, which shows that the link failure has been cleared. All alarms are output to the Link Maintenance output group.
Table C-7 Signaling Link Unsolicited Alarm Messages
Link Failure | UAM Number | UAM Text |
---|---|---|
Recovery: Link Available |
0200 |
RCVRY-LKF: link available |
Failure: Remote NE Loopback |
0201 |
REPT-LKF: remote NE loopback |
Failure: Hardware Problems |
0202 |
REPT-LKF: HWP - too many link interrupts |
Failure: Failed Remote FE Loopback |
0202 |
REPT-LKF: remote FE loopback |
Failure: MTP3 Changeover Order (COO) Message Received |
0218 |
REPT-LKF: COO - rcvd changeover order |
Management Inhibit: Remote |
0234 |
REPT-LKF: RMI remote inhibited |
Management Inhibit: Local |
0235 |
REPT-LINK-MGTINH: local inhibited |
Failure: Unresolved - Default failure reason |
0236 |
REPT-LKF: not aligned |
Failure: False Congestion Restart |
0236 |
REPT-LKF: false congestion restart |
Failure: MTP Link Restart Delayed |
0236 |
REPT-LKF: MTP link restart delayed |
Excessive Duration of Far End Receiving Congestion |
0237 |
REPT-LKF: LM Timer NO-CREDIT expired |
Excessive Delay of Acknowledgment |
0238 |
REPT-LKF: XDA - Timer NO-RESPONSE expired |
Local Processor Outage(management initiated) |
0239 |
REPT-LKF: MBL - local processor outage |
SSCF Remote Release: Remote Processor Outage |
0240 |
REPT-LKF: rcvd SSCOP END-proc. outage |
SSCF Remote Release: Out of Service |
0241 |
REPT-LKF: rcvd SSCOP END-out of service |
SSCF Remote Release: Protocol Error |
0242 |
REPT-LKF: rcvd SSCOP END-protocol error |
SSCF Remote Release: Management Initiated |
0243 |
REPT-LKF: rcvd SSCOP END-mgmnt initiated |
Facility Outage - DS1 Loss of Signal failure |
0244 |
REPT-LKF: FAC - DS1 LOS failure |
Facility Outage - DS1 Loss of Frame failure |
0245 |
REPT-LKF: FAC - DS1 LOF failure |
Facility Outage - DS1 Loss of Cell Delineation failure |
0246 |
REPT-LKF: FAC - DS1 LCD failure |
Excessive In Service Error Rate |
0247 |
REPT-LKF: XER - ISERM threshold exceeded |
UIMs
There are two types UIMs generated with ATM high-speed signaling links, UIMs for large MSUs and UIMs for the loopback tests. UIMs 1172 and 1173 are generated for MTP MSUs (1172) and SCCP MSUs (1173).
The large MSUs are discarded at the receiving ATM high-speed signaling link rather than the outbound link.
UIM 1172 Example
0018.1172 CARD 1103 INFO REPT-OVSZMSG: MTP MSU too large to route. LEN=279 SIO=03 DPC=001-001-001 OPC=002-002-002 LSN=A1234567 Report Date: 97-10-30 Time: 16:27:19
UIM 1173 Example
0018.1173 CARD 1103 INFO REPT-OVSZMSG: SCCP MSU too large to route. LEN=279 SIO=03 DPC=001-001-001 OPC=002-002-002 MSG TYPE=09 CDPA: AI=8B PC=003-003-003 SSN=005 TT=250 ADDR=1234567890 CGPA: AI=8B PC=004-004-004 SSN=006 TT=251 ADDR=0123456789 LSN=A1234567 Report Date: 97-10-30 Time: 16:27:19
The UIMs shown in Table C-8 are generated when loopback tests performed on the ATM high-speed signaling link are completed.
Table C-8 Loopback Test UIMs
UIM # | Severity | Message Text | UIM is Generated When … |
---|---|---|---|
1156 |
None |
Loopback success |
loopback test passes. |
1157 |
None |
Loopback failed |
loopback test failed. |
1158 |
None |
Loopback aborted |
request to activate link is received while running a loopback. |
1159 |
None |
Loopback in progress |
loopback request received while the same loopback test is already in progress. |
1170 |
None |
Loopback prevented |
loopback setup was not performed because the specified type of loopback requires a BOC to be transmitted and this function was prevented from transmitting a BOC. |
1171 |
None |
Loopback invalid |
loopback setup was not performed because invalid parameters were provided. |