0364 - Config. Data Checksum Mismatch

This indicates the OAP configuration data does not match the OAP configuration data stored in the system database. There is a mismatch between the system and OAP databases.

Example

RLGHNCXA21W 94-02-07 12:01:43 EST EAGLE 35.0.0
* 0014.0364  * OAP A   Config. Data checksum mismatch

Alarm Level: Minor

Recovery

1. Enter the following command to retrieve the OAP configuration data stored in the system:
   rtrv-oap-config

   The output of the rtrv-oap-config command displays different fields depending on whether the SEAS feature is on, the LNP feature is on, or both features are on. The following output example shows both the SEAS and LNP features on.

   rtrv-oap-config
       RLGHNCXA03W 99-01-07 00:57:31 EST EAGLE 35.0.0
       OAP CONFIGURATION REPORT
   DATA               OAP A                  OAP B
   Hostname           tekelec-8              tekelec-9
   IP Address         128.132.064.015        128.132.064.016
   IP Netmask         <Not Configured>       <Not Configured>
   Default Router     <Not Configured>       <Not Configured>
   Config             dual                   dual
   SEAC CLLI          SEASNJPYRRC            SEASNJPYRRC
   X25 Packet Size    7                      7
   X25 Mode           DTE                    DTE
   Active LSMS        shadow                 shadow
   Main LSMS NSAP     198.089.039.022        198.089.039.022
   Main LSMS SSEL     emss                   emss
   Main LSMS PSEL     emsp                   emsp
   Shadow LSMS NSAP   198.089.039.023        198.089.039.023
   Shadow LSMS SSEL   emss                   emss
   Shadow LSMS PSEL   emsp                   emsp

2. Review the retrieved information, looking for errors or unprovisioned parameters.
   Table 3-4 lists OAP configuration parameters from the above output that must be provisioned if a given feature is on.

   Table 3-4 OAP Configuration Parameters

   Output	Legend	Feature
   Hostname	Host name of OAP A or OAP B	LNP or SEAS
   IP Address	IP address of OAP A or OAP B	LNP
   IP Netmask	The netmask for OAP A or OAP B	Not required
   Default Router	The IP address of the default router assigned to OAP A or OAP B	Not required
   Config	The number of OAPs configured (single or dual)	LNP or SEAS
   SEAC CLLI	The common language location identifier (CLLI) of the SEAC to which the OAP connects.	SEAS
   X25 Packet Size	The X.25 package size for the link to the SEAC (7 or 8)	SEAS
   X25 Mode	The mode of the X.25 link to the SEAC (DTE or DTC)	SEAS
   Active LSMS	The LSMS associated with the OAP (main or shadow)	LNP
   Main LSMS NSAP	The network service access point of the main LSMS (If lsms=shadow, this parameter set is not mandatory.)	LNP
   Main LSMS SSEL	The session selector of the main LSMS (If lsms=shadow, this parameter set is not mandatory.)	LNP
   Main LSMS PSEL	The presentation selector of the main LSMS (If lsms=shadow, this parameter set is not mandatory.)	LNP
   Shadow LSMS NSAP	The network service access point of the shadow LSMS (If lsms=main, this parameter set is not mandatory.)	LNP
   Shadow LSMS SSEL	The session selector of the shadow LSMS (If lsms=main, this parameter set is not mandatory.)	LNP
   Shadow LSMS PSEL	The presentation selector of the shadow LSMS (If lsms=main, this parameter set is not mandatory.)	LNP

   Note:

   If you find no errors or provision omissions, go to 4. If you find errors or provision omissions, contact your IS department to obtain the correct values and contact My Oracle Support (MOS).
3. Enter the following command to update the OAP database:
   act-oap-config
4. If the fault does not clear, contact My Oracle Support (MOS).