| Oracle® Communications EAGLE Database Administration - SS7 User's Guide Release 46.8 F11884 Revision 1 |
|
 Previous |
 Next |
| Oracle® Communications EAGLE Database Administration - SS7 User's Guide Release 46.8 F11884 Revision 1 |
|
|
Previous |
Next |
This procedure is used to add an exception route to the database using the ent-rtx command. The ent-rtx command uses these parameters.
:dpc/dpca/dpci/dpcn/dpcn24 – The destination point code of the node that the traffic is being sent to.
:opc/opca/opci/opcn/opcn24 – The originating point code of the node sending traffic to the EAGLE.
Note:
See Point Code Formats for a definition of the point code types that are used on the EAGLE and for a definition of the different formats that can be used for ITU national point codes.:ilsn – The name of the linkset carrying incoming traffic to the EAGLE.
:lsn – The name of the linkset that will carry the traffic to the node specified by the destination point code.
:si – The service indicator value that will be assigned to the exception route. The value of the si parameter is 3 to 15.
:cic – The circuit identification code (CIC) value that will be assigned to an exception route containing a single CIC entry or the CIC value that begins a range of CICs that will be assigned to the exception route. The value of the cic parameter is 0 to 16383.
:ecic – The circuit identification code value that ends the range of CICs that will be assigned to the exception route. The value of the ecic parameter is 0 to 16383.
:rc – The relative cost value (priority) that will be assigned to the exception route. The value of the rc parameter is 0 to 99.
:force – This parameter allows an exception route to be added to the database even if the ilsn parameter value is the same as the lsn parameter value. This parameter has only one value, yes.
The combinations of these parameters that can be used with the ent-rtx command are shown in Table 3-27.
To add an exception route to the database, the Origin-Based MTP Routing feature must be enabled and turned on. If error message E4584 is displayed after the rtrv-rtx command is executed, the Origin-Based MTP Routing feature is not enabled or turned on.
E4584 Cmd Rej: MTP Origin Based Routing Feature must be ON
If the Origin-Based MTP Routing feature is not enabled or turned on, perform the Activating the Origin-Based MTP Routing Feature procedure to enable, if required, and turn on the Origin-Based MTP Routing feature.
The DPC value assigned to the exception route must be assigned to a route. If the required route is not shown in the rtrv-rte output, perform on of these procedures to add the required route.
The names of the linksets required specified for the lsn and ilsn parameters must be provisioned in the database. This can be verified by entering the rtrv-ls command. If the required linkset is not in the database, perform one of these procedures to add the linkset.
The linkset must be added according to the rules shown in the "Adding Linksets for Exception Routes" section.
Adding Linksets for Exception Routes
The linkset must be added according to the following rules:
dpc value of the exception route entry is an ANSI point code, the adjacent point code of the lsn value must be an ANSI point code. opc parameter value cannot be the adjacent point code of the linkset that is specified by the lsn parameter value. dpc value of the exception route entry is an ITU-I point code, the adjacent point code of the lsn value must be an ITU-I point code. If the linkset contains an SAPC (secondary adjacent point code), the adjacent point code of the lsn value can be either an ITU-N or ITU-N24 point code if the sapc value is an ITU-I point code. If the adjacent point code of the lsn value is an ITU-N point code with a group code, when the exception route is added, the group code of the adjacent point code of the linkset does not have to be the same as the group code of the opcn value. If an ITU-N linkset is specified for the ilsn parameter, the group code of the adjacent point code of the ilsn value does not have to match the group code of the adjacent point code of the lsn value. dpc value of the exception route entry is an ITU-N point code, the adjacent point code of the lsn value must be an ITU-N point code. dpc value of the exception route entry is an ITU-N point code with no group code assigned to the ITU-N point code, the adjacent point code of the lsn value or the adjacent point code of all the linksets in the routeset can be an ITU-I point code if the sapc (secondary adjacent point code) value is an ITU-N point code. dpc value of the exception route entry is an ITU-N point code with a group code, the adjacent point code of the lsn value can be an ITU-I point code if the sapc value is an ITU-N point code. When the exception route is added, the group code of the dpcn value and the opcn value must be the same. The group code of the adjacent point code of the lsn value and the ilsn value must be the same. The group code of the dpcn value must be the same as the group code of either the adjacent point code of the lsn value or the sapc (secondary adjacent point code) assigned to the lsn value. dpc value of the exception route entry is an ITU-N24 point code, the adjacent point code of the lsn value must be an ITU-N24 point code. If the linkset contains an SAPC (secondary adjacent point code), the adjacent point code of the lsn value can be an ITU-I point code if the sapc value is an ITU-N24 point code. The SAPC values assigned to the linksets can be verified by entering the rtrv-ls:lsn=<linkset name> command.
rtrv-rtx command. This is an example of the possible output.
rlghncxa03w 08-02-11 11:43:04 GMT EAGLE5 38.0.0
DPCA RTX-CRITERIA LSN RC APC
003-003-003 OPCA
009-009-009 lsn1 3 002-002-002
010-010-010 lsn1 2 002-002-002
ILSN
lsn3 lsn2 2 002-002-003
lsn4 lsn2 1 002-002-003
CIC - ECIC
15 15 lsn2 1 002-002-003
17 17 lsn2 7 002-002-003
18 30 lsn1 8 002-002-002
SI
3 lsn2 5 002-002-003
5 lsn2 5 002-002-003
DPCI RTX-CRITERIA LSN RC APC
0-123-7 OPCI
1-222-3 lsn3 10 1-234-5
1-222-4 lsn3 11 1-234-5
1-222-5 lsn4 11 2-145-6
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 12
TOTAL DPC(s): 32
CAPACITY (% FULL): 2%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
If the rtrv-rtx output contains any entries, the Origin-Based MTP Routing feature is enabled. Continue the procedure with 3.
If error message E4584 is displayed after the rtrv-rtx command is executed, the Origin-Based MTP Routing feature is not turned on.
E4584 Cmd Rej: MTP Origin Based Routing Feature must be ON
If error message E4584 is displayed, perform the Activating the Origin-Based MTP Routing Feature procedure to enable, if required, and turn on the Origin-Based MTP Routing feature. After the Origin-Based MTP Routing feature is turned on, continue the procedure with 2.
rtrv-dstn command with the msar=only parameter. This is an example of the possible output.
rlghncxa03w 08-02-11 11:43:04 GMT EAGLE5 38.0.0
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 12
TOTAL DPC(s): 32
CAPACITY (% FULL): 2%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
ent-dstn command and the number of exception routes provisioned by ent-rtx command. The number of entries in the EAGLE’s routing table cannot exceed the number of DPCs allocated in the routing table, shown in the DESTINATION ENTRIES ALLOCATED: row of the rtrv-rtx and rtrv-dstn output. The EAGLE can contain a maximum of 10,000 entries in the routing table. The total number of entries provisioned in the routing table is shown in the TOTAL DPC(s): row of the rtrv-dstn or rtrv-rtx output. If adding the new exception route entry would exceed the number of DPCs allocated in the routing table, perform one of these actions:
After either these actions are performed, continue the procedure with 4.
Note:
If adding the new exception route entry would exceed the number of DPCs allocated in the routing table and neither of these actions are performed, this procedure cannot be performed. If the number of DPCs provisioned in the routing table is10,000, the only action that can be performed that would allow the addition of new exception routes is to remove existing entries from the routing table.If adding the new exception route entry would not exceed the number of DPCs allocated in the routing table, continue the procedure with 4.
rtrv-rte command. If the new exception route entry will be added to an existing DPC shown in the rtrv-rtx output, continue the procedure with 5.
This is an example of the possible output.
rlghncxa03w 10-12-10 11:43:04 GMT EAGLE5 43.0.0
Extended Processing Time may be Required
DPCA ALIASI ALIASN/N24 LSN RC APCA
002-002-002 ---------- -------------- ---------- -- -----------
RTX:No CLLI=-----------
002-002-003 ---------- -------------- ---------- -- -----------
RTX:No CLLI=-----------
003-003-003 ---------- -------------- lsn1 1 002-002-002
lsn2 2 002-002-003
RTX:Yes CLLI=-----------
004-004-004 ---------- -------------- ---------- -- -----------
RTX:No CLLI=-----------
005-005-005 ---------- -------------- ---------- -- -----------
RTX:No CLLI=-----------
006-006-006 ---------- -------------- lsn11 1 004-004-004
lsn12 2 005-005-006
RTX:No CLLI=-----------
DPCI ALIASN/N24 ALIASA LSN RC APC
0-123-7 -------------- -------------- lsn3 1 1-234-5
lsn4 2 2-145-6
RTX:Yes CLLI=-----------
1-234-5 -------------- -------------- ---------- -- -----------
RTX:No CLLI=-----------
2-145-6 -------------- -------------- ---------- -- -----------
RTX:No CLLI=-----------
3-025-6 -------------- -------------- lsn13 1 1-100-5
lsn14 2 4-139-4
RTX:No CLLI=-----------
1-100-5 -------------- -------------- ---------- -- -----------
RTX:No CLLI=-----------
4-139-4 -------------- -------------- ---------- -- -----------
RTX:No CLLI=-----------
DPCN ALIASA ALIASI LSN RC APC
00002 -------------- ---------- ---------- -- -----------
RTX:No CLLI=-----------
00003 -------------- ---------- ---------- -- -----------
RTX:Yes CLLI=-----------
00004 -------------- ---------- lsn5 1 00002
lsn6 2 00003
RTX:No CLLI=-----------
11302 -------------- ---------- ---------- -- -----------
RTX:No CLLI=-----------
12567 -------------- ---------- ---------- -- -----------
RTX:No CLLI=-----------
09852 -------------- ---------- lsn15 1 11302
lsn16 2 12567
RTX:No CLLI=-----------
DPCN24 ALIASA ALIASI LSN RC APC
rtrv-rte output, perform one of these procedures to add the required route.
After the required routes have been configured, continue the procedure with 5.
rtrv-ls command. This is an example of the possible output.
rlghncxa03w 06-10-10 11:43:04 GMT EAGLE5 38.0.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsn1 002-002-002 none 1 1 no B 2 off off off no off
lsn2 002-002-003 none 1 1 no B 3 off off off no off
lsn11 004-004-004 none 1 1 no B 1 off off off no off
lsn12 005-005-005 none 1 1 no B 4 off off off no off
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsn3 1-234-5 none 1 2 no B 2 off off off --- off
lsn4 2-145-6 none 1 2 no B 2 off off off --- off
lsn13 1-100-5 none 1 2 no B 1 off off off --- off
lsn14 4-139-4 none 1 2 no B 1 off off off --- off
L3T SLT GWS GWS GWS
LSN APCN (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsn5 00002 none 1 2 no B 2 off off off --- off
lsn6 00003 none 1 2 no B 2 off off off --- off
lsn15 11302 none 1 2 no B 2 off off off --- off
lsn16 12567 none 1 2 no B 2 off off off --- off
Link set table is (12 of 1024) 1% full.
If the required linkset is not in the database, perform one of these procedures to add the linkset.
The linkset must be added according to the rules shown in the "Adding Linksets for Exception Routes" section.
Note:
If the DPC exception route entry is an ANSI DPC, the adjacent point code of thelsn value must be an ANSI point code. If the DPC exception route entry is an ANSI DPC, continue the procedure with7. rtrv-ls command with the name of the linkset. For this example, enter these commands.
rtrv-ls:lsn=lsn13
This is an example of the possible output.
rlghncxa03w 08-02-11 11:43:04 GMT EAGLE5 38.0.0
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsn13 1-100-5 none 1 2 no B 1 off off off --- off
CLLI TFATCABMLQ MTPRSE ASL8 SLSOCBIT SLSRSB MULTGC
----------- 1 no --- none 7 no
ITUTFR RANDSLS
off all
IPGWAPC MATELSN IPTPS LSUSEALM SLKUSEALM GTTMODE
no ---------- --- --- --- CdPA
LOC LINK SLC TYPE IPLIML2
1301 A 0 IPLIMI M2PA
SAPCN
11211
Link set table is (12 of 1024) 1% full.
rtrv-ls:lsn=lsn16
This is an example of the possible output.
rlghncxa03w 08-02-11 11:43:04 GMT EAGLE5 38.0.0
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsn16 12567 none 1 2 no B 2 off off off --- off
CLLI TFATCABMLQ MTPRSE ASL8 SLSOCBIT SLSRSB MULTGC
----------- 1 no --- none 7 no
ITUTFR RANDSLS
off all
IPGWAPC MATELSN IPTPS LSUSEALM SLKUSEALM GTTMODE
no ---------- --- --- --- CdPA
LOC LINK SLC TYPE IPLIML2
1301 A 0 IPLIMI M2PA
SAPCI
5-067-1
Link set table is (12 of 1024) 1% full.
If the linkset does not meet the criteria shown in the "Adding Linksets for Exception Routes" section, either choose another linkset from the rtrv-ls output in 5 and repeat this step, or add a new linkset by performing one of these procedures:
rtrv-rtx command in 1, continue the procedure with 14. rtrv-rtx command in 1, continue the procedure with 13. rtrv-dstn command. Note:
If cluster point codes are displayed in thertrv-rtx orrtrv-rte outputs, skip this step and continue the procedure with8. This is an example of the possible output.
rlghncxa03w 10-12-10 11:43:04 GMT EAGLE5 43.0.0
Extended Processing Time may be Required
DPCA CLLI BEI ELEI ALIASI ALIASN/N24 DMN
002-002-002 ----------- no --- ---------- -------------- SS7
002-002-003 ----------- no --- ---------- -------------- SS7
003-003-003 ----------- no --- ---------- -------------- SS7
004-004-004 ----------- no --- ---------- -------------- SS7
005-005-005 ----------- no --- ---------- -------------- SS7
006-006-006 ----------- no --- ---------- -------------- SS7
DPCI CLLI BEI ELEI ALIASA ALIASN/N24 DMN
1-234-5 ----------- no --- -------------- -------------- SS7
2-145-6 ----------- no --- -------------- -------------- SS7
0-123-7 ----------- no --- -------------- -------------- SS7
3-025-6 ----------- no --- -------------- -------------- SS7
1-100-5 ----------- no --- -------------- -------------- SS7
4-139-4 ----------- no --- -------------- -------------- SS7
5-067-1 ----------- no --- -------------- -------------- SS7
DPCN CLLI BEI ELEI ALIASA ALIASI DMN
00002 ----------- no --- -------------- ---------- SS7
00003 ----------- no --- -------------- ---------- SS7
00004 ----------- no --- -------------- ---------- SS7
09852 ----------- no --- -------------- ---------- SS7
11211 ----------- no --- -------------- ---------- SS7
11302 ----------- no --- -------------- ---------- SS7
12567 ----------- no --- -------------- ---------- SS7
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 12
TOTAL DPC(s): 32
CAPACITY (% FULL): 2%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
If a cluster point code is not shown in the rtrv-dstn output, continue the procedure with 12.
If a cluster point code is shown in the rtrv-dstn output, and the DPC of the exception route is not a member of a cluster point code, continue the procedure with 12.
If a cluster point code is shown in the rtrv-dstn output, and the DPC of the exception route is a member of a cluster point code, continue the procedure with 8.
rtrv-dstn command with the cluster point code. For this example, enter this command.
rtrv-dstn:dpca=010-010-*
This is an example of the possible output.
rlghncxa03w 10-12-10 11:43:04 GMT EAGLE5 43.0.0
DPCA CLLI BEI ELEI ALIASI ALIASN/N24 DMN
010-010-* ----------- no no ---------- -------------- SS7
SPCA NCAI RCAUSE NPRST SPLITIAM HMSMSC HMSCP SCCPMSGCNV
----------- yes none off none no no none
Destination table is (33 of 2000) 1% full
Alias table is (0 of 12000) 0% full
The DPC of an exception route cannot be a member of a cluster point code unless the NCAI value of the cluster point code is yes. If the NCAI value of the cluster point code is yes, continue the procedure with 12.
If the NCAI value of the cluster point code is no, continue the procedure with 9.
rtrv-feat command. The entry NCR = on in the rtrv-feat command output shows that the NCR feature is on.
Note:
Thertrv-feat command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by thertrv-feat command, see the rtrv-feat command description in Commands User's Guide. If the NCR feature is on, continue the procedure with 11.
If the NCR feature is off, continue the procedure with 10.
chg-feat:ncr=onNote:
Once the NCR feature is turned on with thechg-feat command, it cannot be turned off.The NCR feature must be purchased before you turn the feature on with the chg-feat command. If you are not sure if you have purchased the NCR feature, contact your Sales Representative or Account Representative.
When this command has successfully completed, this message should appear.
rlghncxa03w 06-10-10 11:43:04 GMT EAGLE5 38.0.0 CHG-FEAT: MASP A - COMPLTD
NCAI value for the cluster point code from no to yes by entering the chg-dstn command with the cluster point code and the ncai=yes parameter. For this example, enter this command. chg-dstn:dpca=010-010-*:ncai=yes.
When this command has successfully completed, this message should appear.
rlghncxa03w 08-02-11 15:35:05 GMT EAGLE5 38.0.0
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 12
NETWORK DPC(s): 0
CLUSTER DPC(s): 1
TOTAL DPC(s): 33
CAPACITY (% FULL): 1%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
X-LIST ENTRIES ALLOCATED: 500
CHG-DSTN: MASP A - COMPLTD
Note:
If theopc/opca parameter will not be specified with theent-rtx command, continue the procedure with12. opc/opca value of the exception route can be specified with the network cluster and network cluster member values of the point code as asterisks (*). If the network cluster and network cluster member values of the opc/opca value will not be specified as asterisks, continue the procedure by performing one of the steps shown at the end of this step.
If the network cluster and network cluster member values of the opc/opca value will be specified as asterisks, and the network indicator value of the opc/opca value is 6 or greater, continue the procedure by performing one of the steps shown at the end of this step.
If the network cluster and network cluster member values of the opc/opca value will be specified as asterisks, and the network indicator value of the opc/opca value will be 1 through 5, the PCTYPE value shown in the rtrv-sid output must be OTHER. Enter the rtrv-sid command to verify the PCTYPE value.
This is an example of the possible output.
rlghncxa03w 06-10-10 11:43:04 GMT EAGLE5 38.0.0 PCA PCI PCN CLLI PCTYPE 001-001-001 1-001-1 00001 rlghncxa03w OTHER CPCA 002-002-004 002-002-005 002-002-006 002-002-007 002-002-008 002-002-009 004-002-001 004-003-003 050-060-070 CPCI 1-001-2 1-001-3 1-001-4 1-002-1 1-002-2 1-002-3 1-002-4 2-001-1 7-222-7 CPCN 00050 00060 00070 00100 00080 00090
If the PCTYPE value shown in the rtrv-sid output is OTHER, continue the procedure by performing one of the steps shown at the end of this step.
If the PCTYPE value shown in the rtrv-sid output is ANSI, Change the PCTYPE value of the self-identification of the EAGLE to OTHER by performing the Changing the Self-Identification of the EAGLE procedure. After the PCTYPE value is changed, continue the procedure by performing one of the steps shown at the end of this step.
rtrv-rtx command in 1, continue the procedure with 14. rtrv-rtx command in 1, continue the procedure with 13. lsn parameter value), the 6-Way Loadsharing on Routesets feature must be enabled and turned on. To verify the status of the 6-Way Loadsharing on Routesets feature, enter this command.
rtrv-ctrl-feat:partnum=893019801
The following is an example of the possible output.
rlghncxa03w 09-05-28 21:15:37 GMT EAGLE5 41.0.0 The following features have been permanently enabled: Feature Name Partnum Status Quantity 6-Way LS on Routesets 893019801 on ---- The following features have been temporarily enabled: Feature Name Partnum Status Quantity Trial Period Left Zero entries found. The following features have expired temporary keys: Feature Name Partnum Zero entries found.
If the 6-Way Loadsharing on Routesets feature is not enabled or not turned on, perform the Activating the 6-Way Loadsharing on Routesets Feature procedure to enable and turn on the 6-Way Loadsharing on Routesets feature.
After the 6-Way Loadsharing on Routesets feature has been enabled and turned on, or if the rtrv-ctrl-feat output shows that the 6-Way Loadsharing on Routesets feature is enabled and turned on, continue this procedure with 14.
ent-rtx command and specifying the parameter combinations shown in Table 3-27 for the exception route criteria being assigned to the exception route. Table 3-27 Add Exception Route Parameter Combinations
| OPC- Based Exception Lists | ILSN- Based Exception Lists | SI- Based Exception Lists | Single CIC- Based Exception Lists | Range of CICs- Based Exception Lists |
|---|---|---|---|---|
:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the |
:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the |
:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the |
:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the |
:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the |
:opc/opca/ opci/opcn/ opcn24 = OPC value of the exception route (See Notes 5, 6, and 9) |
:ilsn = incoming linkset name shown in the |
:si = service indicator, 3 - 15 |
:cic = circuit identification code, 0 - 16383 (See Note 8) |
:cic = the circuit identification code value beginning a range of CICs, 0 - 16383 (See Note 8) |
:lsn = linkset name shown in the |
:lsn = linkset name shown in the |
:lsn = linkset name shown in the |
:lsn = linkset name shown in the |
:ecic = the circuit identification code value ending a range of CICs, 0 - 16383 (See Notes 7 and 8) |
:rc = 0 - 99 |
:rc = 0 - 99 |
:rc = 0 - 99 |
:rc = 0 - 99 |
:lsn = linkset name shown in the |
:force=yes (See Note 6) |
:force=yes (See Note 6) |
:rc = 0 - 99 |
||
Notes: 1. The DPC of an exception route entry can contain only a maximum of two entries with the same RC value and with either the same OPC value, the same ILSN value, the same SI value, the same CIC value, or range of CIC values if the 6-Way Loadsharing on Routesets feature is not enabled or turned on. If the 6-Way Loadsharing on Routesets feature is enabled and turned on, the DPC of an exception route entry can contain more than two entries with the same RC value and with either the same OPC value, the same ILSN value, the same SI value, the same CIC value, or range of CIC values, the LSN value for each entry must be different. 2. Each DPC can contain a maximum of six entries with either the same OPC value, the same ILSN value, the same SI value, or the same range of CIC values. The LSN value for each entry must be different. If the 6-Way Loadsharing on Routesets feature is not enabled or turned on, the DPC of a route exception entry can contain only one entry with a single CIC value. If the 6-Way Loadsharing on Routesets feature is enabled and turned on, the DPC of a route exception entry can contain more than one entry with a single CIC value. 4. The linksets specified in this step must meet the criteria shown in the "Adding Linksets for Exception Routes" section. 5. The DPC value cannot be the same as the OPC value. 6. The 7. The 8. The range of CIC values cannot overlap an existing range of CIC values. A single CIC value cannot be within a range of CIC values provisioned for another exception route entry. The 9. Asterisks can be used as the values for the network cluster and network cluster member portions of an ANSI point code value for the |
||||
For this example, enter these commands.
ent-rtx:dpca=006-006-006:opca=125-150-175:lsn=lsn11:rc=10
ent-rtx:dpca=006-006-006:opci=2-103-1:lsn=lsn11:rc=20
ent-rtx:dpca=006-006-006:ilsn=lsn12:lsn=lsn11:rc=11
ent-rtx:dpca=006-006-006:ilsn=lsn13:lsn=lsn11:rc=12
ent-rtx:dpca=006-006-006:si=5:lsn=lsn12:rc=10
ent-rtx:dpca=006-006-006:cic=250:lsn=lsn12:rc=15
ent-rtx:dpca=006-006-006:cic=300:ecic=500:lsn=lsn12:rc=25
ent-rtx:dpci=3-025-6:opca=135-102-089:lsn=lsn13:rc=10
ent-rtx:dpci=3-025-6:opci=4-054-0:lsn=lsn13:rc=15
ent-rtx:dpci=3-025-6:opcn=00503:lsn=lsn13:rc=45
ent-rtx:dpci=3-025-6:ilsn=lsn2:lsn=lsn14:rc=20
ent-rtx:dpci=3-025-6:ilsn=lsn4:lsn=lsn13:rc=25
ent-rtx:dpci=3-025-6:ilsn=lsn16:lsn=lsn16:rc=50:force=yes
ent-rtx:dpci=3-025-6:si=3:lsn=lsn13:rc=30
ent-rtx:dpci=3-025-6:cic=100:lsn=lsn14:rc=35
ent-rtx:dpci=3-025-6:cic=50:ecic=75:lsn=lsn13:rc=40
ent-rtx:dpcn=09852:opca=127-063-048:lsn=lsn15:rc=10
ent-rtx:dpcn=09852:opci=3-037-1:lsn=lsn16:rc=15
ent-rtx:dpcn=09852:opcn=00409:lsn=lsn13:rc=20
ent-rtx:dpcn=09852:ilsn=lsn13:lsn=lsn15:rc=25
ent-rtx:dpcn=09852:ilsn=lsn4:lsn=lsn16:rc=30
ent-rtx:dpcn=09852:si=4:lsn=lsn15:rc=35
ent-rtx:dpcn=09852:cic=1000:lsn=lsn16:rc=40
ent-rtx:dpcn=09852:cic=2000:ecic=3000:lsn=lsn15:rc=45
When each of these commands have successfully completed, this message should appear.
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 ENT-RTX: MASP A - COMPLTD
rtrv-rtx command, specifying these parameters depending on the exception route criteria specified in 14. opc/opca/opci/opcn/opcn24 parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, opc/opca/opci/opcn/opcn24, and lsn. ilsn parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, ilsn, and lsn. si parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, si, and lsn. cic parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, cic, and lsn. cic and ecic parameters were specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, cic, ecic, and lsn. For this example, enter these commands.
rtrv-rtx:dpca=006-006-006:opca=125-150-175:lsn=lsn11
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCA RTX-CRITERIA LSN RC APC
006-006-006 OPCA
125-150-175 lsn11 10 004-004-004
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:opci=2-103-1:lsn=lsn11
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCA RTX-CRITERIA LSN RC APC
006-006-006 OPCI
2-103-1 lsn11 20 004-004-004
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:ilsn=lsn12:lsn=lsn11
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCA RTX-CRITERIA LSN RC APC
006-006-006 ILSN
lsn12 lsn11 11 004-004-004
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:ilsn=lsn13:lsn=lsn11
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCA RTX-CRITERIA LSN RC APC
006-006-006 ILSN
lsn13 lsn11 12 004-004-004
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:si=5:lsn=lsn12
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCA RTX-CRITERIA LSN RC APC
006-006-006 SI
5 lsn12 10 005-005-005
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:cic=250:lsn=lsn12
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCA RTX-CRITERIA LSN RC APC
006-006-006 CIC - ECIC
250 250 lsn12 15 005-005-005
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:cic=300:ecic=500:lsn=lsn12
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCA RTX-CRITERIA LSN RC APC
006-006-006 CIC - ECIC
250 250 lsn12 15 005-005-005
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:opca=135-102-089:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCI RTX-CRITERIA LSN RC APC
3-025-6 OPCA
135-102-089 lsn13 10 1-100-5
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:opci=4-054-0:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCI RTX-CRITERIA LSN RC APC
3-025-6 OPCI
4-054-0 lsn13 15 1-100-5
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:opcn=00503:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCI RTX-CRITERIA LSN RC APC
3-025-6 OPCN
00503 lsn11 15 1-100-5
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:ilsn=lsn2:lsn=lsn14
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCI RTX-CRITERIA LSN RC APC
3-025-6 ILSN
lsn2 lsn14 45 4-139-4
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:ilsn=lsn4:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCI RTX-CRITERIA LSN RC APC
3-025-6 ILSN
lsn4 lsn13 25 1-100-5
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:ilsn=lsn16:lsn=lsn16
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCI RTX-CRITERIA LSN RC APC
3-025-6 ILSN
lsn16 lsn16 50 12567
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:si=3:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCI RTX-CRITERIA LSN RC APC
3-025-6 SI
3 lsn13 30 1-100-5
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:cic=100:lsn=lsn14
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCI RTX-CRITERIA LSN RC APC
3-025-6 CIC - ECIC
100 100 lsn14 35 4-139-4
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:cic=50:ecic=75:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCI RTX-CRITERIA LSN RC APC
3-025-6 CIC - ECIC
50 75 lsn13 40 1-100-5
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:opca=127-063-048:lsn=lsn15
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCN RTX-CRITERIA LSN RC APC
09852 OPCA
127-063-048 lsn15 10 11302
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:opci=3-037-1:lsn=lsn16
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCN RTX-CRITERIA LSN RC APC
09852 OPCI
3-037-1 lsn16 15 12567
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:opcn=00409:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCN RTX-CRITERIA LSN RC APC
09852 OPCN
00409 lsn13 20 1-100-5
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:ilsn=lsn13:lsn=lsn15
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCN RTX-CRITERIA LSN RC APC
09852 ILSN
lsn13 lsn15 25 11302
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:ilsn=lsn4:lsn=lsn16
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCN RTX-CRITERIA LSN RC APC
09852 ILSN
lsn4 lsn16 30 12567
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:si=4:lsn=lsn15
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCN RTX-CRITERIA LSN RC APC
09852 SI
4 lsn15 35 11302
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:cic=1000:lsn=lsn16
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCN RTX-CRITERIA LSN RC APC
09852 CIC - ECIC
1000 lsn16 40 12567
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:cic=2000:ecic=3000:lsn=lsn15
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0
DPCN RTX-CRITERIA LSN RC APC
09852 CIC - ECIC
2000 3000 lsn15 45 11302
DESTINATION ENTRIES ALLOCATED: 2000
FULL DPC(s): 20
EXCEPTION DPC(s): 36
TOTAL DPC(s): 56
CAPACITY (% FULL): 3%
ALIASES ALLOCATED: 12000
ALIASES USED: 0
CAPACITY (% FULL): 0%
chg-db:action=backup:dest=fixed command. These messages should appear, the active Maintenance and Administration Subsystem Processor (MASP) appears first.
BACKUP (FIXED) : MASP A - Backup starts on active MASP. BACKUP (FIXED) : MASP A - Backup on active MASP to fixed disk complete. BACKUP (FIXED) : MASP A - Backup starts on standby MASP. BACKUP (FIXED) : MASP A - Backup on standby MASP to fixed disk complete.
Figure 3-45 Adding an Exception Route Entry
Sheet 1 of 10
Sheet 2 of 10
Sheet 3 of 10
Sheet 4 of 10
Sheet 5 of 10
Sheet 6 of 10
Sheet 7 of 10
Sheet 8 of 10
Sheet 9 of 10
Sheet 10 of 10
