TM-U200A
Table 39-57 DIP Switch 1
Switch No. | Function | ON | OFF | Default Settings |
---|---|---|---|---|
1 |
Data reception error |
Ignored |
Prints “?” |
Off |
2 |
Receive buffer capacity |
40 bytes |
ANK model: 1000 bytes Multilingual model: 512 bytes |
Off |
3 |
Handshaking |
XON/XOFF |
DTR/DSR |
Off |
4 |
Word length |
7 bit |
8 bit |
Off |
5 |
Parity check |
Yes |
No |
Off |
6 |
Parity selection |
Even |
Odd |
Off |
7 |
Baud rate selection |
4800 bps |
9600 bps |
Off |
8 |
BUSY condition |
Receive buffer-full |
Off-line Receive buffer-full |
Off |
Table 39-58 DIP Switch 2
Switch No. | Function | ON | OFF | Default Settings |
---|---|---|---|---|
1 |
Selects number of characters per line (cpl) 7x9 font / 9x9 font |
42 cpl / 35 cpl |
40 cpl / 33 cpl |
Off |
2 |
For internal use only (*1) (Autocutter) |
Enabled |
Disabled |
On |
3 |
For internal use only (*1) (Autocutter) |
Asynchronous |
Synchronous with clock |
Off |
4 |
Undefined |
– |
– |
Off |
5 |
For internal use only (*1) (Semi-autoloading) |
For type A |
For type B/D |
On |
6 |
For internal use only (*1) (Flash memory rewriting) |
Enabled |
Disabled |
Off |
7 |
Pin 6 reset signal |
Used |
Not used |
Off |
8 |
Pin 25 reset signal |
Used |
Not used |
Off |
Table 39-59 DIP Switch 1
Switch No. | Function | ON | OFF | Default Settings |
---|---|---|---|---|
1 |
Auto line feed |
Enabled |
Disabled |
Off |
2 |
Receive buffer |
40 bytes |
– |
Off |
3–7 |
Undefined |
– |
– |
Off |
8 |
Busy condition |
Receive buffer-full |
Off-line Receive buffer-full |
Off |
Table 39-60 DIP Switch 2
Switch No. | Function | ON | OFF | Default Settings |
---|---|---|---|---|
1 |
Selects number of characters per line (cpl) 7x9 font / 9x9 font |
42 cpl / 35 cpl |
40 cpl / 33 cpl |
Off |
2 |
For internal use only (*1) (Autocutter) |
Enabled |
Disabled |
On |
3 |
For internal use only (*1) (Interface synchronization) |
Asynchronous |
Synchronous with clock |
Off |
4 |
Undefined |
– |
– |
Off |
5 |
For internal use only (*1) (semi-autoloading) |
For Type A |
For type B/D |
On |
6 |
For internal use only (*1) (Flash memory rewriting) |
Enabled |
Disabled |
Off |
7 |
Undefined |
– |
– |
Off |
8 |
Pin 31 reset signal |
Used |
Not Used |
On |
TM-U200B/D
RS-232 serial interface model
Table 39-61 DIP Switch 1
Switch No. | Function | ON | OFF | Default B | Default D |
---|---|---|---|---|---|
1 |
Data reception error |
Ignored |
Prints “?” |
Off |
Off |
2 |
Receive buffer capacity |
40 bytes |
ANK model: 1000 bytes Multilingual model: 512 bytes |
Off |
Off |
3 |
Handshaking |
XON/XOFF |
DTR/DSR |
Off |
Off |
4 |
Word length |
7 bit |
8 bit |
Off |
Off |
5 |
Parity check |
Yes |
No |
Off |
Off |
6 |
Parity selection |
Even |
Odd |
Off |
Off |
7 |
Baud rate selection |
4800 bps |
9600 bps |
Off |
Off |
8 |
BUSY condition |
Receive buffer-full |
Off-line Receive buffer-full |
Off |
Off |
Table 39-62 DIP Switch 2
Switch No. | Function | ON | OFF | Default B | Default D |
---|---|---|---|---|---|
1 |
Selects number of characters per line (cpl) 7x9 font / 9x9 font |
42 cpl / 35 cpl |
40 cpl / 33 cpl |
Off |
Off |
2 |
For internal use only (*1) (Autocutter) |
Enabled |
Disabled |
On |
Off |
3 |
Pin 6 reset signal |
Used |
Not used |
Off |
Off |
4 |
Pin 25 reset signal |
Used |
Not used |
Off |
Off |
5 |
For internal use only (*1) (Semi-autoloading) |
For type A |
For type B/D |
Off |
Off |
6 |
For internal use only (*1) (Flash memory rewriting) |
Enabled |
Disabled |
Off |
Off |
7 |
For internal use only (*1) (Interface synchronization) |
Asynchronous |
Synchronous with clock |
Off |
Off |
8 |
Undefined |
– |
– |
Off |
Off |
*1: Do not change the settings of DIP switches 2–2, 2–5, 2–6, and 2–7.
Parallel interface model
Table 39-63 DIP Switch 1
Switch No. | Function | ON | OFF | Default B | Default D |
---|---|---|---|---|---|
1 |
Auto line feed |
Enabled |
Disabled |
Off |
Off |
2 |
Receive buffer |
40 bytes |
ANK Model: 1000 bytes Multilingual mode: 512 bytes |
Off |
Off |
3–7 |
Undefined |
– |
– |
Off |
Off |
8 |
Busy condition |
Receive buffer-full |
Off-line Receive buffer-full |
Off |
Off |
Table 39-64 DIP Switch 2
Switch No. | Function | ON | OFF | Default B | Default D |
---|---|---|---|---|---|
1 |
Selects number of characters per line (cpl) 7 x 9 / 9 x 9 font |
42 cpl / 35 cpl |
40 cpl / 33 cpl |
Off |
Off |
2 |
For internal use only (*1) (Autocutter) |
Enabled |
Disabled |
On |
Off |
3 |
Undefined |
– |
– |
Off |
Off |
4 |
Pin 31 reset signal |
Used |
Not used |
On |
On |
5 |
For internal use only (*1) (semi-autoloading) |
For type A |
For type B/D |
Off |
Off |
6 |
For internal use only (*1) (Flash memory rewriting) |
Enabled |
Disabled |
Off |
Off |
7 |
For internal use only (*1) (Interface synchronization) |
Asynchronous |
Synchronous with clock |
Off |
Off |
8 |
Undefined |
– |
– |
Off |
Off |
*1: Do not change the settings of DIP switches 2–2, 2–5, 2–6, and 2–7.
TM-U220A/B/D (STD)
Serial interface model
Table 39-65 DIP Switch 1
Switch No. | Function | ON | OFF | Default A | Default B | Default D |
---|---|---|---|---|---|---|
1 |
Data reception error |
Ignored |
Print “?” |
Off |
Off |
Off |
2 |
Receive buffer capacity |
40 bytes |
4 KB |
Off |
Off |
Off |
3 |
Handshaking |
XON/XOFF |
DTR/DSR |
Off |
Off |
Off |
4 |
Word length |
7 bits |
8 bits |
Off |
Off |
Off |
5 |
Parity check |
Yes |
No |
Off |
Off |
Off |
6 |
Parity selection |
Even |
Odd |
Off |
Off |
Off |
7 |
Transmission speed selection |
4800 bps |
9600 bps |
Off |
Off |
Off |
8 |
BUSY condition |
Receive buffer-full |
Offline Receive buffer-full |
Off |
Off |
Off |
Table 39-66 DIP Switch 2
Switch No. | Function | ON | OFF | Default A | Default B | Default D |
---|---|---|---|---|---|---|
1 |
Selects number of characters per line (cpl) (*) |
42 cpl / 35 cpl |
40 cpl / 33 cpl |
Off |
Off |
Off |
2 |
Reserved (Autocutter) |
Enabled |
Disabled |
On |
On |
Off |
3 |
Undefined |
— |
– |
Off |
Off |
Off |
4 |
Serial communication set selection |
By memory switch |
By DIP switch |
Off |
Off |
Off |
5 |
Undefined |
– |
— |
Off |
Off |
Off |
6 |
Reserved (Flash memory rewriting) |
Enabled |
Disabled |
Off |
Off |
Off |
7 |
Pin 6 reset signal |
Used |
Not used |
Off |
Off |
Off |
8 |
Pin 25 reset signal |
Used |
Not used |
Off |
Off |
Off |
(*) Selection of dots between characters: On = 2 half dots, Off = 3 half dots
The number of characters per line in the Table indicates for the 76 mm-width paper.
Parallel interface model
Table 39-67 DIP Switch 1
Switch No. | Function | ON | OFF | Default A | Default B | Default D |
---|---|---|---|---|---|---|
1 |
Auto line feed |
Enabled |
Disabled |
Off |
Off |
Off |
2 |
Receive buffer |
40 bytes |
4KB |
Off |
Off |
Off |
3 |
Undefined |
– |
– |
Off |
Off |
Off |
4 |
Undefined |
– |
– |
Off |
Off |
Off |
5 |
Undefined |
– |
– |
Off |
Off |
Off |
6 |
Undefined |
– |
– |
Off |
Off |
Off |
7 |
Undefined |
– |
– |
Off |
Off |
Off |
8 |
BUSY condition |
Receive buffer-full |
Offline Receive buffer-full |
Off |
Off |
Off |
Table 39-68 DIP Switch 2
Switch No. | Function | ON | OFF | Default A | Default B | Default D |
---|---|---|---|---|---|---|
1 |
Selects number of characters per line (cpl) (*) |
42 cpl / 35 cpl |
40 cpl / 33 cpl |
Off |
Off |
Off |
2 |
Reserved (Autocutter) |
Enabled |
Disabled |
On |
On |
Off |
3 |
Undefined |
– |
– |
Off |
Off |
Off |
4 |
Undefined |
– |
– |
Off |
Off |
Off |
5 |
Undefined |
– |
– |
Off |
Off |
Off |
6 |
Reserved (Flash memory rewriting) |
Enabled |
Disabled |
Off |
Off |
Off |
7 |
Undefined |
– |
– |
Off |
Off |
Off |
8 |
Pin 31 reset signal |
Used |
Not used |
On |
On |
On |
(*) Selection of dots between characters: On = 2 half dots, Off = 3 half dots.
The number of characters per line in the Table indicates for the 76 mm-width paper.
TM-U220B/D (US STD)
Serial interface model
Table 39-69 DIP Switch 1
Switch No. | Function | ON | OFF | Default B | Default D |
---|---|---|---|---|---|
1 |
Printing mode |
Right side up printing mode |
Normal printing mode |
Off |
Off |
2 |
Receive buffer capacity |
40 bytes |
4KB |
Off |
Off |
3 |
Handshaking |
XON/XOFF |
DTR/DSR |
Off |
Off |
4 |
Word length |
7 bits |
8 bits |
Off |
Off |
5 |
Parity check |
Yes |
No |
Off |
Off |
6 |
Parity selection |
Even |
Odd |
Off |
Off |
7 |
Transmission speed selection |
4800 bps |
9600 bps |
Off |
Off |
8 |
BUSY condition |
Receive buffer-full |
Offline Receive buffer-full |
Off |
Off |
Table 39-70 DIP Switch 2
Switch No. | Function | ON | OFF | Default B | Default D |
---|---|---|---|---|---|
1 |
Selects number of characters per line (cpl) (*) |
42 cpl / 35 cpl |
40 cpl / 33 cpl |
Off |
Off |
2 |
Reserved (Autocutter) |
Enabled |
Disabled |
On |
Off |
3 |
Pin 6 reset signal |
Used |
Not used |
Off |
Off |
4 |
Pin 25 reset signal |
Used |
Not used |
Off |
Off |
5 |
Undefined |
– |
– |
Off |
Off |
6 |
Reserved (Flash memory rewriting) |
Enabled |
Disabled |
Off |
Off |
7 |
Undefined |
– |
– |
Off |
Off |
8 |
Serial communication set selection |
By memory switch |
By DIP switch |
Off |
Off |
(*) Selection of dots between characters: On = 2 half dots, Off = 3 half dots.
The number of characters per line in the Table indicates for the 76 mm-width paper.
Parallel interface model
Table 39-71 DIP Switch 1
Switch No. | Function | ON | OFF | Default B | Default D |
---|---|---|---|---|---|
1 |
Printing mode |
Right side up printing mode |
Normal printing mode |
Off |
Off |
2 |
Receive buffer |
40 bytes |
4KB |
Off |
Off |
3 |
Undefined |
– |
– |
Off |
Off |
4 |
Undefined |
– |
– |
Off |
Off |
5 |
Undefined |
– |
– |
Off |
Off |
6 |
Undefined |
– |
– |
Off |
Off |
7 |
Undefined |
– |
– |
Off |
Off |
8 |
BUSY condition |
Receive buffer-full |
Offline Receive buffer-full |
Off |
Off |
Table 39-72 DIP Switch 2
Switch No. | Function | ON | OFF | Default B | Default D |
---|---|---|---|---|---|
1 |
Selects number of characters per line (cpl) (*) |
42 cpl / 35 cpl |
40 cpl / 33 cpl |
Off |
Off |
2 |
Reserved (Autocutter) |
Enabled |
Disabled |
On |
Off |
3 |
Undefined |
– |
– |
Off |
Off |
4 |
Pin 31 reset signal |
Used |
Not used |
On |
On |
5 |
Undefined |
– |
– |
Off |
Off |
6 |
Reserved (Flash memory rewriting) |
Enabled |
Disabled |
Off |
Off |
7 |
Undefined |
– |
– |
Off |
Off |
8 |
Undefined |
– |
– |
Off |
Off |
(*) Selection of dots between characters: On = 2 half dots, Off = 3 half dots.
The number of characters per line in the Table indicates for the 76 mm-width paper.
TM-T88III/IV/V
TM-T70
Serial interface specification
Table 39-73 DIP Switch 1
SW 1 | Function | ON | OFF | Factory Setting |
---|---|---|---|---|
1 |
Data reception error |
Ignored |
Prints “?” |
OFF |
2 |
Receive buffer capacity |
45 bytes |
4 KB |
OFF |
3 |
Handshaking |
XON/XOFF |
DTR/DSR |
OFF |
4 |
Word length |
7 bits |
8 bits |
OFF |
5 |
Parity check |
Yes |
No |
OFF |
6 |
Selection of parity |
Even |
Odd |
OFF |
7 |
Selection of transmission speed |
See Table 18 |
See Table 18 |
ON |
8 |
Selection of transmission speed |
See Table 18 |
See Table 18 |
OFF |
Table 39-74 Transmission Speed
Transmission speed (bps) | SW 1–7 | SW 1–8 |
---|---|---|
(*1) |
ON |
ON |
4800 |
OFF |
ON |
9600 |
ON |
OFF |
19200 |
OFF |
OFF |
bps: bits per second
Table 39-75 DIP Switch 2
SW 2 | Function | ON | OFF | Factory Setting |
---|---|---|---|---|
1 |
Handshaking (Condition or BUSY) |
Receive buffer full |
Offline Receive buffer-full |
OFF |
2 |
Reserved (Do not change settings) |
Fixed to OFF |
Fixed to OFF |
OFF |
3 |
Selects print density |
See Table 20 |
See Table 20 |
OFF |
4 |
Selects print density |
See Table 20 |
See Table 20 |
OFF |
5 |
Setting the conditions that cancel the receive buffer BUSY state (This function is effective when the receive buffer capacity is set to 4 KB.) |
Cancels the BUSY state when the remaining capacity of the receive buffer reaches 138 bytes. |
Cancels the BUSY state when the remaining capacity of the receive buffer reaches 256 bytes. |
OFF |
6 |
Reserved (Do not change settings) |
Fixed to OFF |
Fixed to OFF |
OFF |
7 |
I/F pin 6 reset signal |
Enabled |
Disabled |
OFF |
8 |
I/F pin 25 reset signal |
Enabled |
Disabled |
OFF |
Table 39-76 DIP Switch 2–3 and 2–4
Switch No. 3 | Switch No. 4 | Function |
---|---|---|
OFF |
OFF |
Print density (Standard) |
ON |
OFF |
Print density (Medium) |
OFF |
ON |
Print density (Dark) |
ON |
ON |
Prohibited |
Parallel interface specification
Table 39-77 DIP Switch 1
SW | Function | ON | OFF | Factory Setting |
---|---|---|---|---|
1 |
Auto line feed |
Always enabled |
Always disabled |
OFF |
2 |
Receive buffer capacity |
45 bytes |
4 KB |
OFF |
3 |
Selects paper sensors to output paper-end signals (default value of ESC c 3) |
Disabled |
Roll paper end sensor enabled; roll paper near-end sensor enabled |
OFF |
4 |
Sets error signal |
Disabled |
Enabled |
OFF |
5–8 |
Undefined |
– |
– |
OFF |
Table 39-78 DIP Switch 2
SW | Function | ON | OFF | Factory Setting |
---|---|---|---|---|
1 |
Handshaking (Condition for BUSY) |
Receive buffer full |
Offline Receive buffer full |
OFF |
2 |
Reserved (Do not change settings) |
Fixed to OFF |
Fixed to OFF |
OFF |
3 |
Selects print density |
See Table 23 |
See Table 23 |
OFF |
4 |
Selects print density |
See Table 23 |
See Table 23 |
OFF |
5 |
Setting the conditions that cancel the receive buffer BUSY state (this function is effective when the capacity of the receive buffer is set to 4 KB). |
Cancels the BUSY state when the remaining capacity of the receive buffer reaches 138 bytes. |
Cancels the BUSY state when the remaining capacity of the receive buffer reaches 256 bytes. |
OFF |
6 |
Reserved (Do not change settings) |
Fixed to OFF |
Fixed to OFF |
OFF |
7 |
Reserved (Do not change settings) |
Fixed to OFF |
Fixed to OFF |
OFF |
8 |
Interface pin 31 reset signal (Do not change settings) |
Fixed to ON |
Fixed to ON |
ON |
Table 39-79 DIP Switch 2–3 and 2–4
3 | 4 | Function |
---|---|---|
OFF |
OFF |
Print density (Standard) |
ON |
OFF |
Print density (Medium) |
OFF |
ON |
Print density (Dark) |
ON |
ON |
Prohibited |
TM-T70II
Table 39-80 Memory Switch 1
Memory Switch | Function | Setting Value — 48 (OFF) | Setting Value — 49 (ON) | Defaults |
---|---|---|---|---|
1–1 |
(Reserved) |
– |
– |
48 (OFF) |
1–2 |
Receive buffer capacity |
4 KB |
45 bytes |
48 (OFF) |
1–3 |
Condition for BUSY |
Receive buffer full or offline |
Receive buffer full |
48 (OFF) |
1–4 |
Data processing for receiving error |
Replaced with “?” |
Ignored |
48 (OFF) |
1–5 |
Automatic line feed |
Always disabled |
Always enabled |
48 (OFF) |
1–6 |
(Reserved) |
– |
– |
48 (OFF) |
1–7 |
(Reserved) |
– |
– |
48 (OFF) |
1–8 |
(Reserved) |
– |
– |
48 (OFF) |
Table 39-81 Memory Switch 2
Memory Switch | Function | Setting Value — 48 (OFF) | Setting Value — 49 (ON) | Defaults |
---|---|---|---|---|
2–1 to 2–8 |
(Reserved) |
– |
– |
48 (OFF) |
Table 39-82 Memory Switch 3
Memory Switch | Function | Setting Value — 48 (OFF) | Setting Value — 49 (ON) | Defaults |
---|---|---|---|---|
3–1 to 3–8 |
(Reserved) |
– |
– |
48 (OFF) |
Table 39-83 Memory Switch 4
Memory Switch | Function | Setting Value — 48 (OFF) | Setting Value — 49 (ON) | Defaults |
---|---|---|---|---|
4–1 to 4–8 |
(Reserved) |
– |
– |
48 (OFF) |
Table 39-84 Memory Switch 5
Memory Switch | Function | Setting Value — 48 (OFF) | Setting Value — 49 (ON) | Defaults |
---|---|---|---|---|
5–1 |
Sets USB power-saving function *1 |
Enabled |
Disabled |
48 (OFF) |
5–2 |
Sets recovery conditions from receive buffer BUSY (Enabled when the receive buffer capacity is set to 4 KB) |
Recovers when the remaining receive buffer capacity becomes 256 bytes |
Recovers when the remaining receive buffer capacity becomes 138 bytes |
48 (OFF) |
5–3 |
Selects paper sensors to output paper-end signals (default value of ESC c 3) |
Roll paper end sensor enabled; roll paper near-end sensor enabled |
Disabled |
48 (OFF) |
5–4 |
Sets error signal |
Enabled |
Disabled |
48 (OFF) |
5–5 |
(Reserved) |
– |
– |
48 (OFF) |
5–6 |
(Reserved) |
– |
– |
48 (OFF) |
5–7 |
(Reserved) |
– |
– |
48 (OFF) |
5–8 |
(Reserved) |
– |
– |
48 (OFF) |
*1: Valid only when the USB interface communication condition is set to the vendor-defined class and the system configuration is set so that the USB driver can support the USB power-saving function.
Function 11
Function 11 — Descriptions
Sets the configuration item for the serial interface specified by a to the values specified by d.
a | Configuration Item |
---|---|
1 |
Transmission speed |
2 |
Parity |
3 |
Handshaking |
4 |
Bit length |
Transmission speed settings (a = 1)
d1...dk | Transmission Speed |
---|---|
“2400” |
2400 bps |
“4800” |
4800 bps |
“9600” |
9600 bps |
“19200” |
19200 bps |
“38400” |
38400 bps |
“57600” |
57600 bps |
“115200” |
115200 bps |
Parity settings (a =2)
d1 | Parity |
---|---|
48 |
None |
49 |
Odd |
50 |
Even |
Handshaking settings (a = 3)
d1 | Handshaking |
---|---|
48 |
DTR/DSR control |
49 |
XON/XOFF control |
Bit length settings (a = 4)
d1 | Bit Length |
---|---|
55 |
7 bits |
56 |
8 bits |