Connection Name
|
Name of the Connection
|
MP Server Hostname
|
Hostname of the MP server from which status is reported:
- Fixed (non-IPFE)
Connections are always reported by the DA-MP that hosts the Fixed Connection
- Established IPFE
Connections are always reported by the DA-MP that hosts the established IPFE
Connection
- Non-Established
IPFE Connections (ones that have been configured, but are currently not
assigned to a DA-MP by IPFE) are reported by the MP Leader
|
Dynamic
|
Indicates whether or not the element was created dynamically
(YES) or
statically (NO).
NO is assigned for
all element instances, except for those created via Dynamic Peer Discovery.
|
Admin State
|
A Connection's administrative state can be:
- Enabled: the
Connection is Enabled
- Disabled: the
Connection is Disabled
- Unk: unknown; the
state of the Connection is not available in the database
|
Connection Type
|
Indicates the connection type (Diameter or
(RADIUS).
|
Connection Mode
|
Specifies the connection mode used for Peer discovery.
The Connection can have one of the following Connection Modes:
-
Initiator Only
-
Indicates that all connections to discovered Peers are
Initiator Only; the application attempts to initiate connection to these Peers.
-
Initiator & Responder
-
Indicates that all connections to discovered Peers are
of the type Initiator & Responder; the application attempts to initiate
connection to the discovered Peers as well as listen for connection attempts
from these Peers.
-
RADIUS Server
-
Indicates that RCL can only receive RADIUS Request
messages and send RADIUS Response messages of the Connection.
-
RADIUS Client
-
Indicates that RCL can only send RADIUS Request messages
and receives RADIUS Response messages of the Connection.
|
Operational Status
|
A Connection's administrative state can be:
- Available: the
Connection is available for routing
- Degraded: the
Connection is not unavailable but it is not operating as expected. The
Operational Reason field provides additional information on this status.
- Unavailable: the
Connection is unavailable. The Operational Reason field provides additional
information on this status.
|
CPL
|
The Connection Priority Level is the maximum of the
following values:
- Operational Status
(0=available; 3=degraded; 99=unavailable)
- Remote Busy
Congestion Level (0-3)
- Egress Transport
Congestion Level (0-98)
- Egress Message
Rate Congestion Level (0-3)
|
Operational Reason
|
Reason for the Operational Status. The following reasons can
occur:
- Disabled
- Connecting
- Listening
- Abnormal
- Disconnecting
- Proving
- Watchdog
- Remote Busy
Congestion
- Egress Transport
Congestion
- Egress Message
Rate Congestion
- Normal
- Peer with reduced
IP set
|
Local Node
|
Local Node associated with the Connection
|
Local Port
|
Specifies the local port used for Peer discovery.
|
IPFE Initiator DAMP
|
The IPFE Initiator DA-MP for this connection.
|
Peer Node
|
Peer Node associated with the Connection
|
Remote IP Addresses
|
The IP address(es) of the Peer Node associated with the
Connection
|
Remote Port
|
The Listen Port of the Peer Node associated with the
Connection
|
Local Initiate Port
|
The Local Initiate Port associated with the Connection
|
Ingress Msgs Per Second
|
A 30-second running average of the Ingress messages
processed by the Connection
|
Common Application IDs
|
A comma-separated list of Application IDs received in a
Diameter CEA message, or a list of Application Names. The first 10 Application
IDs received in the CEA are listed.
Note:
For local nodes, CEAs are sent in response to erroneous CERs.
|
Transport Congestion Abatement Timeout
|
The amount of time spent at Egress Transport Congestion
Levels 3, 2, and 1 during Egress Transport Congestion Abatement
|
Remote Busy Usage
|
Indicates which Request messages can be forwarded on this
Connection after receiving a DIAMETER_TOO_BUSY response from the Connection's
Peer.
-
Disabled
- The Connection is not considered to be BUSY after
receiving a DIAMETER_TOO_BUSY response. All Request messages continue to be
forwarded to (or rerouted to) this Connection.
-
Enabled
- The Connection is considered to be BUSY after receiving a
DIAMETER_TOO_BUSY response. No Request messages are forwarded to (or rerouted
to) this Connection until the
Remote Busy Abatement
Timeout expires.
-
Host Override
- The Connection is considered to be BUSY after receiving a
DIAMETER_TOO_BUSY response. Only Request messages whose Destination-Host AVP
value is the same as the Connection's Peer FQDN can be forwarded to (or
rerouted to) this Connection until the
Remote Busy Abatement
Timeout expires.
|
Remote Busy Abatement Timeout
|
If Remote Busy Usage is Enabled or Host Override, this is
the time in seconds that the Connection is considered BUSY from the last time a
DIAMETER_TOO_BUSY response was received.
|
Message Priority Setting
|
Indicates the source of Message Priority for a Request
message arriving on the Connection. Possible settings are:
- None - use the
Default Message Priority Configuration Set
- Read from Request
Message - read the Message Priority from the ingress Request
- User Configured -
Apply the user configured Message Priority Configuration Set
|
Message Priority Configuration Set
|
The Message Priority Configuration Set associated with the
Connection
|
Egress Message Throttling Configuration Set
|
The Egress Message Throttling Configuration Set associated
with the Connection
|
Egress Msgs Per Second
|
The most recent Egress Message Rate on the Connection
|
Test Mode
|
Indicates if this is a Test Connection
|
PDUs to Diagnose
|
For a test Connection currently undergoing diagnosis, this
shows the number of PDUs yet to be diagnosed.
|
Time of Last Update
|
Time stamp that shows the last time the status information
was updated
|
Connection Alarm Group Name
|
If the Alarm Group feature is enabled (on the
page), this column displays the connection alarm
group name where the connection belongs.
|
Alarm IDs
|
If the Alarm Group feature is enabled (on the
page), this column displays the Alarm ID raised
against the Connection. If more than one alarm is raised by the DA-MP for a
Connection, then the values are separated by a comma.
|