5.1.39 MTP3 Config

A Mtp3 Config is an entity to configure all the m3rl timers.

Select the VSTP, and then Configuration, and then MTP3 Configs page. The page displays the fields on the MTP3 Configs View, Insert, and Edit pages.

Note:

Data Input Notes apply to the Insert and Edit pages only; the View page is read-only.

Table 5-39 MTP3 Configs Fields

Field Description Data Input Notes
Name Name for this M3rl Config, which must be unique within the VSTP site. Valid names are strings between one and 32 characters, inclusive. Valid characters are alphanumeric and underscore. The name must contain at least one alpha and must not start with a digit. [A value is required.]
Linkset On Hold timer Link addition/deletion changeover timer duration. This timer introduces a delay to help prevent message mis-sequencing on link add/deletion. Typical value is 60. [MIN,MAX] = [10,2000]
Signaling Link Test T1 Timer Supervision timer for signaling link test acknowledgement message. Typical value is 12000.[MIN,MAX] = [4000,12000]
Signaling Link Test T2 Timer Interval timer for sending signaling link test messages. Typical value is 30000.[MIN,MAX] = [30000,90000]
Signaling Link Test T17 Timer SLT T17 timer set. Typical value is 2000. [MIN,MAX] = [500,2000]
Timer 10 Waiting to repeat signalling route set test message. Default value is 30000.[MIN,MAX] = [20000,90000]
Timer 11 Transfer restricted timer. Default value is 30000. [MIN,MAX] = [1000,90000]
Timer 12 Waiting for uninhibit acknowledgement. Default value is 800. [MIN,MAX] = [100, 2000]
Timer 13 Waiting for force uninhibit. Default value is 800.[MIN,MAX] = [100, 2000]
Timer 15 Waiting to start signalling route set congestion test. Default value is 3000.[MIN,MAX] = [200,4000]
Timer 16 Waiting for route set congestion status update. Default value is 1400.[MIN,MAX] = [200,3000]
Timer 17 Delay to avoid oscillation of initial alignment failure and link restart. Default value is 800.[MIN,MAX] = [500, 2000]
Timer 18 Repeat transfer restricted (TFR) once by response method. Default value is 10000.[MIN,MAX] = [2000,20000]
Timer 1 Delay to avoid message mis-sequencing on changeover. Default value is 800.[MIN,MAX] = [100,2000]
Timer 2 Waiting for changeover acknowledgement. Default value is 1400.[MIN,MAX] = [100,3000]
Timer 23 Remote inhibit test timer. Default value is 180000.[MIN,MAX] = [180000,360000]
Timer 3 Time controlled diversion-delay to avoid mis-sequencing on changeback. Default value is 800.[MIN,MAX] = [100,2000]
Timer 4 Waiting for changeback acknowledgement (first attempt). Default value is 800.[MIN,MAX] = [100,2000]
Timer 5 Waiting for changeback acknowledgement (second attempt). Default value is 800.[MIN,MAX] = [100,2000]
Timer 6 Delay to avoid message mis-sequencing on controlled rerouting. Default value is 800.[MIN,MAX] = [100,2000]
Timer 8 Transfer prohibited inhibition timer (transient solution). Default value is 800.[MIN,MAX] = [500,2000]

You can perform add, edit, or delete tasks on VSTPConfigurationMTP3 Configs page.

Adding a MTP3 Config

Perform the following steps to configure a new MTP3 Config:

  1. Click Insert.

    Note:

    The new MTP3 Config must have a name that is unique across all MTP3 Configs at the SOAM. In addition, the MTP3 Config's IP Port combination must also be unique across all MTP3 Configs configured at the SOAM.
  2. Enter the applicable values.
  3. Click OK, Apply, or Cancel

Editing a MTP3 Config

Use this procedure to change the field values for a selected MTP3 Config. (The MTP3 Config Name field cannot be changed.):
  1. Select the MTP3 Config row to be edited.
  2. Click Edit
  3. Enter the updated values.
  4. Click OK, Apply, or Cancel

Deleting a MTP3 Config

Use the following procedure to delete a MTP3 Config.

Note:

You cannot delete a MTP3 Config if it is part of the configuration of one or more Linksets.
  1. Select the MTP3 Config to be deleted.
  2. Click Delete.
  3. Click OK or Cancel.