The following is an example of configuring BMC using
ipmitool (version 1.8.6).
Log in as
ipmitoolcan communicate with the BMC using the IPMI driver by using the command
bmc info, and looking for a device ID in the output. For example:
# ipmitool bmc info Device ID : 32 . . .
ipmitoolis not communicating with the BMC, then review the section Configuring the BMC and ensure that the IPMI driver is running.
Enable IPMI over LAN using the following procedure
Determine the channel number for the channel used for IPMI over LAN. Beginning with channel 1, run the following command until you find the channel that displays LAN attributes (for example, the IP address):
# ipmitool lan print 1 . . . IP Address Source : 0x01 IP Address : 188.8.131.52 . . .
Turn on LAN access for the channel found. For example, where the channel is 1:
# ipmitool -I bmc lan set 1 access on
Configure IP address settings for IPMI using the static IP addressing procedure:
Using static IP Addressing
If the BMC shares a network connection with ILOM, then the IP address must be on the same subnet. You must set not only the IP address, but also the proper values for netmask, and the default gateway. For example, assuming the channel is 1:
# ipmitool -I bmc lan set 1 ipaddr 192.168.0.55 # ipmitool -I bmc lan set 1 netmask 255.255.255.0 # ipmitool -I bmc lan set 1 defgw ipaddr 192.168.0.1
Note that the specified address (
192.168.0.55) is associated only with the BMC, and does not respond to normal pings.
Establish an administration account with a username and password, using the following procedure (assuming the channel is 1):
Set BMC to require password authentication for ADMIN access over LAN. For example:
# ipmitool -I bmc lan set 1 auth ADMIN MD5,PASSWORD
List the account slots on the BMC, and identify an unused slot less than the maximum ID and not listed, for example, ID 4 in the following example. Note that some slots may be reserved and not available for reuse on some hardware.
# ipmitool user summary 1 Maximum IDs : 20 Enabled User Count : 3 Fixed Name Count : 2 # ipmitool user list 1 ID Name Enabled Callin Link Auth IPMI Msg Channel Priv Lim 1 true false false true USER 2 root true false false true ADMINISTRATOR 3 sysoper true true false true OPERATOR 12 default true true false true NO ACCESS 13 true false true false CALLBACK
In the example above, there are 20 possible slots, and the first unused slot is number 4.
Assign the desired administrator user name and password and enable messaging for the identified slot. (Note that for IPMI v1.5 the user name and password can be at most 16 characters). Also, set the privilege level for that slot when accessed over LAN (channel 1) to ADMIN (level 4). For example, where
usernameis the administrative user name, and
passwordis the password:
# ipmitool user set name 4 username # ipmitool user set password 4 password # ipmitool user enable 4 # ipmitool channel setaccess 1 4 privilege=4 # ipmitool channel setaccess 1 4 link=on # ipmitool channel setaccess 1 4 ipmi=on
Verify the setup using the command
lan print 1. The output should appear similar to the following. Note that the items in bold text are the settings made in the preceding configuration steps, and comments or alternative options are indicated within brackets :
# ipmitool lan print 1 Set in Progress : Set Complete Auth Type Support : NONE MD2 MD5 PASSWORD Auth Type Enable : Callback : MD2 MD5 : User : MD2 MD5 : Operator : MD2 MD5 : Admin : MD5 PASSWORD : OEM : MD2 MD5 IP Address Source : DHCP Address [or Static Address] IP Address : 192.168.0.55 Subnet Mask : 255.255.255.0 MAC Address : 00:14:22:23:fa:f9 SNMP Community String : public IP Header : TTL=0x40 Flags=0x40 Precedence=… Default Gateway IP : 192.168.0.1 Default Gateway MAC : 00:00:00:00:00:00 . . . # ipmitool channel getaccess 1 4 Maximum User IDs : 10 Enabled User IDs : 2 User ID : 4 User Name : username [This is the administration user] Fixed Name : No Access Available : call-in / callback Link Authentication : enabled IPMI Messaging : enabled Privilege Level : ADMINISTRATOR
Verify that the BMC is accessible and controllable from a remote node in your cluster using the bmc info command. For example, if
node2-ipmiis the network host name assigned the IP address of
node2's BMC, then to verify the BMC on node
node1, with the administrator account
username, enter the following command on
$ ipmitool -H node2-ipmi -U username lan print 1
You are prompted for a password. Provide the IPMI password.
If the BMC is correctly configured, then you should see information about the BMC on the remote node. If you see an error message, such as
Error: Unable to establish LAN session, then you must check the BMC configuration on the remote node.
Repeat this process for each cluster member node. If the IPMI administrator account credentials on each cluster member node are not identical, then IPMI will fail during configuration.