Debug Commands

act-gedti

Use this command to activate a GEDTI Hub for Eagle Eyes. The state of the GEDTI Hub is changed from DACT(Deactivated) to ACT(Active).

Note:

The GEDTI hub must be Deactived on the specified card before the command can be executed. If the card boots, then the status of the GEDTI Hub will be reset to DACT.

Parameters

loc (mandatory): The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

Example

act-gedti:loc=1102

Dependencies

The value specified for the loc parameter must refer to an equipped card location.

2101 E2101 Cmd Rej: Card location is unequipped.

The card at the specified location must be configured as GEDTI Hub.

2144 E2144 Cmd Rej: Location invalid for hardware configuration

Activating the state of GEDTI Hub that is already activated has no effect.

3827 E3827 Cmd Rej: No change requested

The card at the specified location must not be a reserved location.

2154 E2154 Cmd Rej: Card slot reserved by system

Notes

None.

Output

act-gedti:loc=1101


Command Accepted - Processing

tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0 act-gedti:loc=1101
Command entered at terminal #1.; 

tekelecstp 11-08-16 18:35:44 MST
UNKNOWN EAGLE 46.0.0 Activate GEDTI Hub message sent to card.;


tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0
Command Completed.;

Related Topics

act-ip-lnk

Use this command to activate an IP link and put the link into service. The state of the link is changed from OOS-MT-DSBLD (Out-Of-Service-Maintenance-Disabled) to OOS-MT (Out-Of-Service-Maintenance), IS-ANR (In-Service-Abnormal) or IS-NR (In-Service-Normal).

Note:

The specified card must be Active before the command can be executed. If the card boots, then the status of the IP link will be reset.

Parameters

loc (mandatory)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1113, 1115

port (mandatory)

Ethernet interface Port ID.

Range:

a: IP Port A
b: IP Port B
c: IP Port C
d: IP Port D
fca: Fast Copy Port A
fcb: Fast Copy Port B

Example

act-ip-lnk:loc=1102:port=a

act-ip-lnk:loc=1203:port=fca

act-ip-lnk:loc=1103:port=c

act-ip-lnk:loc=1202:port=d

Dependencies

The value specified for the loc parameter must refer to one of the following cards, and the referenced card must be equipped:

E5-ENET-B card running the EROUTE, IPGWx, IPLIMx, or IPSG application
IPSM card
E5-SM4G or E5-SM8G-B card running the VSCCP application
E5-OAM card running the OAMHC application
E5-MCPM-B
SLIC card

A valid value must be specified for the loc parameter.

2376 E2376 Cmd Rej: Specified LOC is invalid

The value specified for the port parameter must be supported by the card:

port A - E5-OAM card running OAMHC application, IPSM card, E5-MCPM-B card
port A, B - E5-ENET-B card running the EROUTE or IPLIMx application, E5-SM4G or E5-SM8G-B card running the VSCCP application
port A, B, FCA, FCB - E5-ENET-B card running the IPGWx or IPSG application
port A, B, C and D are valid for SIP/ENUM/DEIR application running on SLIC card.

2975 E2975 Cmd Rej: Specified Port is not supported

The card at the specified location must be configured.

2144 E2144 Cmd Rej: Location invalid for hardware configuration

The card in the specified location must be Active before this command can be executed.

2387 E2387 Cmd Rej: Card is not in service

Notes

The act-ip-lnk/dact-ip-lnk commands were created as debug means - aids to turn off or disable the IP interface to troubleshoot network problems, specifically to allow the operator to troubleshoot IP network flooding issues that can cause EAGLE cards to boot repeatedly while trying to come up. These commands should NOT be used for general maintenance actions since they have not been rigorously tested and their usage should be limited to situations like described above.

Interface A/D is used for ExAP connectivity and interface B/C is used for the signaling network on the SLIC card running the SIP/ENUM/DEIR application.

Output

act-ip-lnk:loc=1101:port=a

Command Accepted - Processing

    tekelecstp 11-08-16 19:52:01 MST  EAGLE 44.0.0
    act-ip-lnk:loc=1101:port=a
    Command entered at terminal #1.
;

    tekelecstp 11-08-16 19:52:01 MST  EAGLE 44.0.0
    Activate IP link message sent to card.
;

    tekelecstp 11-08-16 19:52:01 MST  EAGLE 44.0.0
    Command Completed.
;

act-ip-lnk:loc=1103:port=c

Command Accepted - Processing

    tekelecstp 16-05-25 03:48:33 MST   EAGLE 46.4.0.0.0-69.1.0
    act-ip-lnk:loc=1103:port=c
    Command entered at terminal #18.
;

    tekelecstp 16-05-25 03:48:33 MST   EAGLE 46.4.0.0.0-69.1.0
    Activate IP link message sent to card.
;

    tekelecstp 16-05-25 03:48:33 MST   EAGLE 46.4.0.0.0-69.1.0
    Command Completed.
;

rtrv-ip-lnk

act-upgrade

Use this command to perform a software upgrade from a source release to the target release on an in-service system.

Caution:

It is strongly recommended that this command be used only in conjunction with the system Upgrade Procedure for your target release. The Upgrade Procedure provides step-by-step information on performing an upgrade.

Parameters

action (mandatory)

The action to be performed for the upgrade process.

Caution:

The convertoam and netcomplete actions should be used only under the direction of My Oracle Support (MOS).

Range:

yyyyyyyyyy

Up to 10 alphabetic characters. Valid actions are:

chkrel—Validates the stored upgrade target release on the physical disk as specified by the src parameter.
convertoam—Converts the standby OAM database.
convertstp—Performs all OAM and network conversions necessary for an upgrade. This command transitions through all of the upgrade phases to upgrade completion. If measurement collection is turned on, this command automatically inhibits measurements during the upgrade. Upon completion of the upgrade, this command returns the MASPs to full-function mode with measurement collection turned back on.
createsets—Assigns network cards to upgrade-grouping sets.
dbstatus—Reports the status of all database partitions on the TDM fixed disks and the removable drive(s) (similar to the rept-stat-db:display=version command).
displaysets—Reports the upgrade-grouping sets of network cards.
getrel—Retrieves the upgrade target release file from either the EAGLE software release distribution server or the plug-in flash drive. It then expands the data on the inactive partition group of the hard disks.
netcomplete—Indicates upgrade completion and places the system in a fully functional mode.
oamcomplete—Sets the upgrade phase number to 3, and enables the beginning of controlled card loading.
refreshsets—Not yet supported.
verifysets—Verifies that the card set list is consistent with the current EAGLE configuration and displays detailed information on any inconsistencies found.

force (optional)

Allows the user to override Card Set List verification and perform upgrade when only minor inconsistencies are present.

Range:: yes
Override the Card Set List verification and perform the upgrade.

release (optional)

The name of the software release file to be downloaded.

This file contains the upgrade target release on the software release distribution server or plug-in flash drive.

Range:: xyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
1 alphabetic character followed by up to 29 alphanumeric characters. One or more periods can be used.

Note:
The value must be at least 11 characters in length and must contain a hyphen (-). The format of the value must be xx.xx.xx-yy.yy.yy, where xx.xx.xx is the release number, and yy.yy.yy is the engineering build number.

src (optional)

The physical disk that contains the upgrade target release.

Range:

fixed: The upgrade target release is on the fixed disk
usb: The upgrade target release is on the removable media inserted in the flush-mount USB port
server: The upgrade target release is on the remote server

thres (optional)

Network Threshold value. The percentage of signaling links that is to remain in service (IS) during the network conversion phase. This enables SCCP thresholding and flashing on non-provisioned cards during the upgrade.

Range:: 50 - 90
Default:: Network cards are updated serially

Example

act-upgrade:action=convertstp

act-upgrade:action=dbstatus

act-upgrade:action=convertstp:thres=75

act-upgrade:action=getrel:release="46.7.0.0.0-74.2.0.tar.gz":src=usb

act-upgrade:action=chkrel:src=fixed

Dependencies

The value specified for the action parameter must correspond to a specific upgrade phase:

action=convertoam—upgrade phase=0 and 1
action=oamcomplete—upgrade phase=2
action=convertnet—upgrade phase=3
action=netcomplete—upgrade phase=3
action=convertstp—upgrade phase=0-3

2172 E2172 Cmd Rej: Command action is out of phase with expected procedure

The Measurements Collection function must be turned off (chg-meas:collect=off) or the Measurements Platform feature must be turned on (chg-measopts:platformenable=on) before a value of convertoam, oamcomplete, or netcomplete can be specified for the action parameter.

2160 E2160 Cmd Rej: Measurements collect must be off

A valid upgrade release must reside on the plug-in flash drive or the inactive partition of the fixed disk.

2962 E2962 Cmd Rej: <Device> is <condition>

The standby OAM database must be the source release.

2180 E2180 Cmd Rej: Current stdby OAM db is not supported for this upgrade

The current OAM database must be the source release.

2179 E2179 Cmd Rej: Current actv OAM db is not supported for this upgrade

The database partition must be coherent.

2967 E2967 Cmd Rej: Active OAM database is incoherent

The database partition must be in the correct functional mode.

2172 E2172 Cmd Rej: Command action is out of phase with expected procedure

The action=convertstp and thres parameters must be specified together in the command.

3443 E3443 Cmd Rej: THRES parm and action=CONVERTSTP must be specified together

Upgrade conversion cannot be initiated from a telnet-type terminal (terminal IDs 17-40).

4283 E4283 Cmd Rej: Command cannot be executed on a Telnet terminal

The DCM cards are obsolete for SS7IPGW, IPGWI, IPLIM, and IPLIMI applications.

2105 E2105 Cmd Rej: Invalid card TYPE and APPL load type combination

The action=getrel and release parameters must be specified together in the command.

2155 E2155 Cmd Rej: Invalid parameter combination specified

An IPSM card must be provisioned and in service before a value of getrel or chkrel can be specified for the action parameter.

2387 E2387 Cmd Rej: Card is not in service

The ent-ftp-serv:app=dist command must be entered before a value of getrel or chkrel can be specified for the action parameter.

2774 E2774 Cmd Rej: FTP Server table entry not found for this APP/IPADDR

The act-upgrade:action=convertstp cannot be issued with any removable media inserted in any of the USB ports.

4851 E4851 Cmd Rej: Removable media can not be inserted

Invalid hardware configuration alarms are set or an HMUX alarm must be addressed.

3908 E3908 Cmd Rej: Invalid OAM HW config or an HMUX card is out of service

All cards that are in the auto-inhibited state must be removed before this command can be entered.

3444 E3444 Cmd Rej: Upgrade prevented due to auto-inhibited card

Cards that prevent the IMT buses from being inhibited during the upgrade cannot exist in the system.

2738 E2738 Cmd Rej: Can not inhibit IMT bus - alternate bus is in abnormal state

The specified source drive must be at the correct database version for the upgrade to proceed.

2945 E2945 Cmd Rej: Source database version is not compatible

The plug-in flash drive cannot contain an EAGLE backup image.

3725 E3725 Cmd Rej: Removable drive database level is not compatible

If the src=usb parameter is selected, then the plug-in flash drive upgrade media must be inserted in the Active OAM's flush-mounted USB port.

4918 E4918 Cmd Rej: Could not access USB disk

The internal RAM disk must be available for the plug-in flash drive's upgrade image to be unpackaged.

4919 E4919 Cmd Rej: Could not access RAM disk

The disk that contains the upgrade target release must be in a known upgrade mode.

3441 E3441 Cmd Rej: Target Release source disk in unknown upgrade mode

If the src=usb or src=server parameter is specified, then the action=getrel parameter must be specified. If the src=fixed parameter is specified, then the action=getrel parameter cannot be specified.

2157 E2157 Cmd Rej: Source parameter invalid for upgrade action

The EAGLE PVN address in the source database cannot be identical to the EAGLE FCNA or FCNB network address in the target database.

5013 E5013 Cmd Rej: PVN, FCNA and FCNB must not be identical

The icdpnunknx and icdpnunknX and the gcdpnunknx and gcdpnunknX NPP Action Sets cannot co-exist in the source release.

5149 E5149 Cmd Rej: Invalid table entry, can not be repaired by conversion code

The value specified for the release parameter must be at least 11 characters in length and contain a hyphen (-). The format of the value must be xx.xx.xx-yy.yy.yy, where xx.xx.xx is the release number, and yy.yy.yy is the engineering build number.

2314 E2314 Cmd Rej: Invalid filename entered

The card must have sufficient DRAM memory to perform the GTMOD table Health Check.

5383 E5383 Cmd Rej: Not enough memory on card

The AMGTT data in the GTT table cannot exceed the capacity of the GTMOD table (100 K).

5283 E5283 Cmd Rej: GTMOD table is full

Unable to access GTT table from source drive.

3119 E3119 Cmd Rej: Failed Reading GTT TRANS table

The MFC feature must be ON prior to upgrading to release 46.2 or later.

3248 E3248 Cmd Rej: MFC Off, upgrade aborted

The action=refreshsets and action=verifysets parameters are not supported.

5480 E5480 Cmd Rej: This upgrade action is unavailable in this release

The thres parameter cannot be specified if the threshold type (threstype) has been changed to set.

5481 E5481 Cmd Rej: THRES parameter not valid when using threstype = SET

When issuing the act-upgrade command with the threstype assigned to card sets, the list of card sets needs to be created and valid.

3241 E3241 Cmd Rej: The Card Set List is not valid, verify or create

When issuing the act-upgrade command with the threstype assigned to Card Set, the card set list must be consistent with the current EAGLE configuration, unless force=yes is allowed and specified. Details of any such inconsistencies and recovery instructions will be reported in a similar manner as act-upgrade:action=verifysets.

3503 E3503 Cmd Rej: Card Configuration is inconsistent with Card Set List

The act-upgrade command cannot be issued when SFAPP(P)->OAM sync is ON.

3637 E3637 Cmd Rej: Turn OFF SFAPP(P)->OAM sync before this command

This command cannot be entered when CAT2 IPSM to OAM syncing is in progress.

3652 E3652 Cmd Rej: IPSM to OAM SYNC in progress

Notes

The act-upgrade:action=convertstp command executes all four upgrade phases consecutively.

If the act-upgrade:action=convertstp command is entered following a command abort, the upgrade processing determines the last upgrade phase that was successfully completed. The upgrade processing then attempts to restart from that point to successful completion. Re-entering the act-upgrade:action=convertstp command following a command abort is the recommended method for recovery.

The TDMs and plug-in flash drives have upgrade phase indicators. The upgrade command expects the disks to be in certain phases before executing a specific action. If the disks are not in the correct phases, an error is generated.

The act-upgrade:action=dbstatus command generates output similar to that provided by the rept-stat-db:display=version command.

The thres parameter is used to:

Allow multiple cards to be upgraded together, as long as the specified percentage of links remains in service. The value is applied to groups of links based upon the link-supporting group or the entire system. The grouping is set by the chg-upgrade-config:threstype= command.
Enable SCCP thresholding, which allows multiple Service Module cards to be upgraded together. The specified thres parameter value is not used to determine the number of Service Module cards to upgrade. The peak SCCP load since the last OAM boot is used to determine the number of cards that must remain in service (at least half of the cards must remain in service).
Enable the non-provisioned flash function, which flash-downloads any boot-prom type card if the card is in the system but not provisioned.

The act-upgrade:action=getrel action defaults to getting the release from the provisioned IPSM card using the provisioned FTP Server. If the src=usb parameter is specified, then the release is obtained from the plug-in USB flash drive upgrade media.

Output

Note:

The act-upgrade:action=convertstp command performs the OAM conversion and the network conversion. During the conversion, this command broadcasts the current activity in the scroll area. Refer to Appendix B of the EAGLE Release Software Upgrade Procedure for a sample of message output.

The action dbstatus reports the current database status.

 act-upgrade:action=dbstatus


eaglestp 15-02-13 11:45:51 MST  EAGLE5 45.0.1-64.70.35 Upg Phase 0
    DATABASE STATUS: >> OK <<
            TDM 1114 ( STDBY)                 TDM 1116 ( ACTV )
            C   LEVEL    TIME LAST BACKUP     C   LEVEL    TIME LAST BACKUP
            - -------- ---------------------- - -------- ----------------------
    FD BKUP Y      210     -        -         Y      210     -        -
    FD CRNT Y      210                        Y      210
            MCAP 1113                         MCAP 1115
            - --------                        - --------
    RD BKUP -    -         -        -         -    -         -        -
    USB BKP -    -         -        -         -    -         -        -

    CARD/APPL  LOC   C  T  LEVEL       TIME LAST UPDATE   VERSION STATUS
    ---------  ----  -  -  ----------  -----------------  -------------------
    OAM-RMV    1113  -  -      -           -        -          -
    TDM-CRNT   1114  Y  N  210         15-01-16 12:22:02  135-000-000  NORMAL
    TDM-BKUP   1114  Y  -  210         15-01-16 12:22:02  135-000-000  NORMAL
    OAM-RMV    1115  -  -      -           -        -          -
    OAM-USB    1115  -  -      -           -        -          -
    TDM-CRNT   1116  Y  N  210         15-01-16 12:22:02  135-000-000  NORMAL
    TDM-BKUP   1116  Y  -  210         15-01-16 12:22:02  135-000-000  NORMAL

    INACTIVE PARTITION GROUP
    CARD/APPL  LOC   C  T  LEVEL       TIME LAST UPDATE   VERSION STATUS
    ---------  ----  -  -  ----------  -----------------  -------------------
    TDM-CRNT   1114  N  -  1           00-00-00 00:00:00  136-000-000  NORMAL
    TDM-BKUP   1114  N  -  1           00-00-00 00:00:00  136-000-000  NORMAL
    TDM-CRNT   1116  Y  -  1           00-00-00 00:00:00  136-000-000  NORMAL
    TDM-BKUP   1116  Y  -  1           00-00-00 00:00:00  136-000-000  NORMAL
;

rept-stat-db

chg-bip-fld

Use this command to manually update the board identification PROM (BIP) data during an upgrade in the field.

Note:

Initial programming of the BIP data occurs during manufacturing.

Parameters

data (mandatory)

Board Identification (BID) record field data.

Range:: zzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz
A character string, specifying board identification field data based on the value of the fld parameter.

fld (mandatory)

Board identification field.

Range:

rev: revision
sm: software match

loc (mandatory)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1112, 1201 - 1218, 1301 - 1318, 2101 - 2118, 2201 - 2218, 2301 - 2318, 3101 - 3118, 3201 - 3218, 3301 - 3318, 4101 - 4118, 4201 - 4218, 4301 - 4318, 5101 - 5118, 5201 - 5218, 5301 - 5318, 6101 - 6118, 6202 - 6212, 6302 - 6312

type (optional)

Type of board.

Range:

mbd: main assembly

Example

This example shows changing of the sm (Software MatchID) field in BIP data of Main assembly:

chg-bip-fld:loc=1102:fld=sm:data="001"

Dependencies

The value of the loc parameter cannot specify a location for a fixed disk or removable drive.

2242 E2242 Cmd Rej: Destination card invalid

Notes

The card in the specified location must be inhibited.

Output

chg-bip-fld:loc=1103:fld=rev:data="B"


    tekelecstp 10-04-01 12:05:44 IST  EAGLE 42.0.0
    Board ID Prom updated. 
;

chg-bip-rec

Use this command to manually update the Board Identification PROM (BIP) data during an upgrade in the field.

Note:

Initial programming of the BIP data occurs during manufacturing.

Parameters

data (mandatory)

Board identification data.

Range:: zzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz
A patterned character string. This data string is generated by entering valid input parameters to the BIP tool.

loc (mandatory)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1112, 1201 - 1218, 1301 - 1318, 2101 - 2118, 2201 - 2218, 2301 - 2318, 3101 - 3118, 3201 - 3218, 3301 - 3318, 4101 - 4118, 4201 - 4218, 4301 - 4318, 5101 - 5118, 5201 - 5218, 5301 - 5318, 6101 - 6118, 6202 - 6212, 6302 - 6312

init (optional)

This parameter initializes the contents of a PROM to contain only the record specified in the data parameter, if that record is a board identification record.

Range:

yes: The contents of the PROM are initialized.
no: The contents of the PROM are not initialized.

Default:

no

typed (optional)

Type of board.

Range:

mbd: main assembly

Example

This example initializes the contents of a main assembly BIP to contain only the record specified in the data parameter:

chg-bip-rec:loc=1105:data=xxxx:init=yes

This example displays the programming of the DCM Ethernet Addresses for Port A (ENT01):

chg-bip-rec:loc=1102:data="ENT01,AD00001704000D,cs104"

Dependencies

The value of the loc parameter cannot specify a location for a fixed disk or removable drive.

2242 E2242 Cmd Rej: Destination card invalid

If the init=yes parameter is specified, then the value of the data parameter must be a Board IDentification (BID) record.

2244 E2244 Cmd Rej: INIT=YES only valid with BID record

Notes

The card in the specified location must be inhibited.

Output

chg-bip-rec:loc=1107:data=xxx:init=yes


    tekelecstp 10-04-01 12:05:44 IST  EAGLE 42.0.0
    Board ID Prom updated. 
;

chg-ee-card

Parameters

Use this command to enter/modify Eagle Eyes Network card data in the Eagle Eyes Card (EE CARD) table. The EE CARD entry consists of Card location and Eagle Eyes specific data.

loc (mandatory)

Eagle Eyes Card location.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

action (optional)

Action to be performed on the specified filter ID for the card.

Range:: attach; detach
Default:: No change to the current value.
System Default:: 0

fltid (optional)

A comma-separated Eagle Eyes Filter ID list to be associated or disassociated with the card. Up to 8 FLT IDs can be specified in the list.

Range:: 1-200
Default:: No change to the current value.
System Default:: 0

kblim (optional)

Sets the file size limit of the capture file created, in kilobytes.

Range:: 1-4000000
Default:: No change to the current value.
System Default:: none

pktlim (optional)

Sets the limit on the number of Ethernet frames to send.

Range:: 1-10000000; none
Default:: No change to the current value.
System Default:: none

seclim (optional)

Sets the limit on the amount of time to perform the trace, in seconds.

Range:: 1-5644800; none
Default:: No change to the current value.
System Default:: none

thr (optional)

Sets the sending rate of the Eagle Eyes throttle task in IMT packets per second. The packets will not be captured unless this parameter is set to a non-zero value for the particular card.

Range:: 1000--10000
Default:: No change to the current value.
System Default:: 0

Example

chg-ee-card:loc=1101:fltid=12:action=attach:thr=2000:pktlim=5000

chg-ee-card:loc=1102:kblim=40000:seclim=3000000

chg-ee-card:loc=1101:fltid=13:action=detach:pktlim=none

Dependencies

If the fltid parameter is specified, then the action parameter must be specified.

2379 E2379 Cmd Rej: Missing parameter

The EE CARD table cannot contain more than 256 entries.

2862 E2862 Cmd Rej: EE Card table is full

The EE CARD table must be accessible.

2867 E2867 Cmd Rej: Unable to read EE Card table

At least one optional parameter must be specified.

2136 E2136 Cmd Rej: At least one optional parameter is required

The fltid specified should not be already associated with the card.

2889 E2889 Cmd Rej: Duplicate filter on card is not allowed.

The value specified for the fltid parameter must already exist in the EE FLT table.

2827 E2827 Cmd Rej: Filter not present

Maximum of 16 include filters can be attached to a card.

2970 E2970 Cmd Rej: Max limit of INC/EXC Filters reached on card

Maximum of 16 exclude filters can be attached to a card.

2970 E2970 Cmd Rej: Max limit of INC/EXC Filters reached on card.

The value specified for the loc parameter must not be a system reserved location.

2154 E2154 Cmd Rej: Card slot reserved by system

The IMT table must be accessible.

2102 E2102 Cmd Rej: Failed reading the IMT table

The card in the location specified by the loc parameter must have Eagle Eyes service capability.

2144 E2144: Location invalid for hardware configuration

The card loc specified to detach a filter must have Eagle Eyes configured.

4916 E4916 Command invalid for hardware configuration

The card at the specified location must be equipped.

2101 E2101 Cmd Rej: Card location is unequipped

The Filter appl and card appl should be same.

2812 E2812 Cmd Rej: EE Filter does not match card appl type

Notes

The value specified for the loc parameter must refer to a card running one of the following GPLs, and the referenced card must be equipped:

IPSG, IPLHC, IPGHC
ATMHC
SS7HC
SIPHC
DEIRHC

Output

chg-ee-card:loc=1101:fltid=12:action=attach:thr=2000:pktlim=5000


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0

    EE CARD table is (2 of 256) 1% full

    CHG-EE-CARD: MASP A - COMPLTD

Related Topics

chg-gedti-card

Use this command to configure GEDTI Hub for Eagle Eyes traffic capture.

Parameters

loc (mandatory)

IPSM Card location to be configured as GEDTI Hub.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

port (mandatory)

GEDTI Port to be set.

Range:: 1025 - 65354

Example

chg-gedti-card:loc=1211:port=1124

Dependencies

The value specified for the loc parameter must correspond to the location of an IPSM card.

2144 E2144 Cmd Rej: Location invalid for hardware configuration

The value specified for the port parameter must not be configured on any other IPSM card.

2975 E2975 Cmd Rej: Specified Port is not supported

If the GEDTI Hub is in ACTIVE state then port cannot be changed.

3726 E3726 Cmd Rej: Active device state does not permit database change

The EE Card table must be accessible.

2867 E2867 Cmd Rej: Unable to read EE Card table

Notes

None.

Output

chg-gedti-card:loc=1211:port=1245


tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0 
EE CARD table is (2 of 256) 1% full 
CHG-GEDTI-CARD:MASP A - COMPLTD ;

Related Topics

chg-tbl

Use this command to create, rename, or reset any table on a fixed disk or removable drive.

Caution:

Before entering the chg-tbl command, contact My Oracle Support.

Parameters

action (mandatory)

The desired action to perform on the table.

Range:

create: Creates a DOS entry in the FAT table and updates the DOS directory table.
rename: Changes the name of an existing system table to a new DOS file name (does not update the dms.cfg file).
reset: Initializes an existing table to the value designated by the resetchar parameter.

disk (mandatory)

Target disk. The disk that contains the file.

Range:

remove: Removable drive
fixed: Fixed disk
usb: Argument to be used by Oracle personnel only.

ext (optional)

Extension. The three character DOS filename extension.

Range:: azz
0–3 ASCII characters

filelength (optional)

The amount of space the file occupies on the disk.

Range:: 1 - 32505856

id (optional)

Table identification number.

Range:: 0 - 499

name (optional)

Name of the file.

Range:: azzzzzzz
1–8 ASCII characters

prtngrp (optional)

Partition group. The disk partition group to be changed.

Range:

active
inactive

Default:

active

resetchar (optional)

Reset character. The table reset character that is written to every byte of the table.

Range:: 0 - 255

Example

chg-tbl:action=create:disk=remove:name=test:ext=sys:filelength=150000

chg-tbl:action=reset:disk=remove:id=0

chg-tbl:action=rename:disk=remove:id=0:name=dms:ext=old

Dependencies

If the action=create/rename parameter is specified, then the name parameter must be specified.

2314 E2314 Cmd Rej: Invalid filename entered

If the action=create parameter is specified, then the name, ext, and filelength parameters must be specified.

2712 E2712 Cmd Rej: RESETCHAR not valid with ACTION=CREATE

If the file type is a directory, the filelength parameter is not required. The directory entry file length is always 1 cluster in length.

N/A N/A

The attributes used during file creation are current date and time of the active MASP. Readable/writable files are allocated contiguously from the last free FAT cluster.

N/A N/A

If the action=reset parameter is specified, then the id parameter must be specified.

2713 E2713 Cmd Rej: FILELENGTH not valid with ACTION=RESET

If the action=rename parameter is specified, then the id, name, and ext parameters must be specified.

2716 E2716 Cmd Rej: RESETCHAR not valid with ACTION=RENAME

This command cannot be used to modify the security log.

3003 E3003 Cmd Rej: Modification of security log not allowed

Notes

None

Output


		  chg-tbl:action=create:disk=remove:name=test:ext=sys:filelength=150000


chg-tbl: CREATE 0K : filename = test.sys, byte length = 150000 
chg-tbl: command complete 
;

 chg-tbl:action=reset:disk=remove:id=0


chg-tbl: RESET OK : Table 0, DMS.CFG 
chg-tbl: command complete 
;


		  chg-tbl:action=rename:disk=remove:id=0:name=dms:ext=old


chg-tbl: RENAME 0K : Table 0, DMS.CFG to DMS.OLD 
chg-tbl: command complete 
;

Related Topics

disp-disk-dir

chg-upgrade-config

Use this command to configure data used by the upgrade software during an upgrade of an in-service EAGLE from a source release to the target release.

Note:

This command stores data that will be used during the software upgrade. The command does not start the software upgrade.

Parameters

addtblcnv (optional)

This parameter sets the flag of the corresponding entry in the Table Conversion Definition table that forces the table to be converted during a software upgrade.

Caution:

The addtblcnv parameter should be used only under the direction of My Oracle Support (MOS).

Range:: 0 - 1023

assignset (optional)

Assigned Set. The card specified by the loc parameter is assigned to the upgrade-grouping set specified by this parameter.

Range:: 0
removes the card from the set list; 2 - 10
assigns the card to that particular set list for the group corresponding to the card type

deltblcnv (optional)

This parameter clears the flag of the corresponding entry in the Table Conversion Definition table that forces the table to be converted during a software upgrade.

Caution:

The deltblcnv parameter should be used only under the direction of My Oracle Support (MOS).

Range:: 0 - 1023

limsets (optional)

LIM Sets. This parameter sets the number of sets for link cards.

Range:: 2 - 10

loc (optional)

Location. The location of a network card to be assigned to a set specified by the assignset parameter.

Range:: 1101 - 1113, 1115, 1201 - 1218, 1301 - 1318, 2101 - 2118, 2201 - 2218, 2301 - 2318, 3101 - 3118, 3201 - 3218, 3301 - 3318, 4101 - 4118, 4201 - 4218, 4301 - 4318, 5101 - 5118, 5201 - 5218, 5301 - 5318, 6101 - 6118

src (optional)

Source. The disk that physically contains the upgrade target release.

Range:

fixed: The upgrade target release is on the fixed disk
remove: The upgrade target release is on the removable drive

srvsets (optional)

Service Sets. This parameter sets the number of sets for service cards.

Range:: 2 - 10

threstype (optional)

Threshold type. The type of thresholding to be used during the upgrade.

Range:

set: Network conversion is based on the defined sets of cards

Example

chg-upgrade-config:addtblcnv=327

chg-upgrade-config:deltblcnv=327

chg-upgrade-config:sak=vbjyapdpbtejb:src=fixed

chg-upgrade-config:threstype=set:srvsets=2:limsets=4

Dependencies

The addtblcnv and deltblcnv parameters cannot be specified together in the command.

4904 E4904 Cmd Rej: ADDTBLCNV and DELTBLCNV cannot be specified together.

One of the optional parameters must be specified in the command.

2136 E2136 Cmd Rej: At least one optional parameter is required

The srvsets and limsets parameters cannot be specified unless the threstype is being changed to or has been changed to set.

5482 E5482 Cmd Rej: SRVSETS or LIMSETS not valid unless threstype = SET

The loc parameter is required when the assignset parameter is specified.

5483 E5483 Cmd Rej: LOC must be specified with ASSIGNSET

The value specified for the assignset parameter cannot be greater than the current value of srvsets or limsets for the specified card.

5484 E5484 Cmd Rej: ASSIGNSET value out of range for card group

The chg-upgrade-config command cannot be issued when SFAPP(P)->OAM sync is ON.

3637 E3637 Cmd Rej: Turn OFF SFAPP(P)->OAM sync before this command

This command cannot be entered when CAT2 IPSM to OAM syncing is in progress.

3652 E3652 Cmd Rej: IPSM to OAM SYNC in progress

Output

chg-upgrade-config:addtblcnv=327


    rlghncxa03w  07-03-13  08:15:45 EST  EAGLE 37.5.0
    Command Completed. 
;

Related Topics

clr-disk-stats

Use this command to clear the disk performance statistics. All associated disk statistics are zeroed.

Parameters

loc (mandatory)

Location. The location of the card.

Range:: 1113, 1115
Default:: none

Example

clr-disk-stats:loc=1113

Dependencies

The specified card location must contain a card that is running an OAM (1113 or 1115).

3291 E3291 Cmd Rej: Card location specified must be an OAM card

A related command must not be in progress.

2368 E2368 Cmd Rej: System busy - try again later

Notes

None

Output

clr-disk-stats:loc=1113


    rlghncxa03w 01-03-01 14:14:05 EST  Rel 28.1.0   
    Disk performance statistics cleared. 
;

Related Topics

disp-disk-stats

copy-tbl

Use this command to copy a single table from one source to another. A table can be copied to any verifiable location in the system; however, the source and destination tables must have identical configurations (same number of entries, same entry size, both 1- dimensional and 2-dimensional).

Note:

A table cannot be copied onto itself.

Parameters

dloc (mandatory)

Destination location. The location of the destination table.

Range:

1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

1114: TDM
1116: TDM
1113: Latched USB port
1115: Latched USB port

sloc (mandatory)

Source location. The location of the source table.

Range:

1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

1114: TDM
1116: TDM
1113: Latched USB port
1115: Latched USB port

stbl (mandatory)

Source table. The identifying number of the source table.

Range:: 0 - 1023

ddrv (optional)

Destination drive. The identification of the disk to which the table is copied.

Range:

fixed: The fixed disk
remove: The removable drive
usb: Argument to be used by Oracle personnel only.

Default:

fixed

dprtngrp (optional)

Disk partition group. The disk partition group of the destination table.

Range:

active
inactive

Default:

active

dtbl (optional)

Destination table. The identifying number of the destination table.

Range:: 0 - 1023
Default:: The stbl parameter value

sdrv (optional)

Source drive. The identification of the disk from which the table is copied.

Range:

fixed: The fixed disk
remove: The removable drive
usb: Argument to be used by Oracle personnel only.

Default:

fixed

sprtngrp (optional)

Source partition group. The disk partition group of the source table.

Range:

active
inactive

Default:

active

Example

copy-tbl:stbl=25:dtbl=24:sloc=1114:dloc=1116:sdrv=fixed

Dependencies

Only one table copy command can be executed at a time.

2368 E2368 Cmd Rej: System busy - try again later

The source and destination tables must exist and be compatible.

N/A N/A

This command cannot be used to modify the security log.

3003 E3003 Cmd Rej: Modification of security log not allowed

The same value cannot be specified for the sloc and dloc or the stbl and dtbl parameters.

4920 E4920 Cmd Rej: Cannot copy table onto itself

If a value of fixed is specified for the sdrv or ddrv parameter, then a value of 1114 or 1116 must be specified for the sloc or dloc parameter.

4912 E4912 Cmd Rej: Disk invalid for specified Location

This command cannot be entered when CAT2 IPSM to OAM syncing is in progress.

3652 E3652 Cmd Rej: IPSM to OAM SYNC in progress

Notes

None

Output


		  copy-tbl:stbl=25:dtbl=24:sloc=1114:dloc=1116:sdrv=fixed


    rlghncxa03w 01-03-04 16:11:53 EST  Rel 28.1.0 
    Table copy command complete. 
;

None.

dact-ee

Use this command to deactivate an Eagle Eyes Card and stop capturing traffic on it. The state of the card is changed from ACT (Active) to DACT (Deactivated).

Note:

If the card boots, then the status of the card would be reset to DACT. This will clear the EE configuration from the card.

Parameters

loc (mandatory)

The Eagle Eyes card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

Example

dact-ee:loc=1203

Dependencies

The card at the specified location must be equipped.

2101 E2101 Cmd Rej: Card location is unequipped

The card should be configured as an Eagle Eyes card.

2984 E2984 Cmd Rej: Eagle Eyes not configured on the card

Notes

The value specified for the loc parameter must refer to a card running one of the following GPLs, and the referenced card must be equipped:

IPSG, IPLHC, IPGHC
ATMHC
SS7HC
SIPHC
DEIRHC
ERTHC

Output

dact-ee:loc=1101


Command Accepted - Processing

tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0 
dact-ee:loc=1101
Command entered at terminal #1.
;


tekelecstp 11-08-16 18:35:44 MST UNKNOWN EAGLE 46.0.0 
Deactivate EE message sent to card. 
;

tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0 
Command Completed.
;

Related Topics

dact-gedti

Use this command to deactivate a GEDTI Hub. The state of the GEDTI Hub is changed from ACT (Active) to DACT (Deactivated).

Note:

The specified card must be Active before the command can be executed. If the card boots, then the status of the GEDTI Hub will be reset to DACT.

Parameters

loc (mandatory)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1113, 1115

Example

dact-gedti:loc=1102

Dependencies

The value specified for the loc parameter must refer to an equipped card location.

2101 E2101 Cmd Rej: Card location is unequipped

A valid value must be specified for the loc parameter.

2376 E2376 Cmd Rej: Specified LOC is invalid

The card at the specified location must be configured as a GEDTI Hub.

2144 E2144 Cmd Rej: Location invalid for hardware configuration

Deactivating the state of a GEDTI Hub that is already deactivated has no effect.

3827 E3827 Cmd Rej: No change requested

Notes

None.

Output

dact-gedti:loc=1101


Command Accepted - Processing

tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0 
dact-gedti:loc=1101
Command entered at terminal #1.
; 

tekelecstp 11-08-16 18:35:44 MST UNKNOWN EAGLE 46.0.0 
Deactivate GEDTI Hub message sent to card. 
;

tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0 
Command Completed.;

Related Topics

dact-ip-lnk

Use this command to deactivate an IP link and put the link out of service. The state of the link is changed from IS-NR (In-Service-Normal), IS-ANR (In-Service-Abnormal), or OOS-MT (Out-Of-Service-Maintenance), to OOS-MT-DSBLD (Out-Of-Service-Maintenance-Disabled).

Note:

The specified card must be Active before the command can be executed. If the card boots, then the status of the IP link will be reset.

Parameters

loc (mandatory)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1113, 1115

port (mandatory)

Ethernet interface Port ID.

Range:

a: IP Port A
b: IP Port B
c: IP Port C
d: IP Port D
fca: Fast Copy Port A
fcb: Fast Copy Port B

Example

dact-ip-lnk:loc=1102:port=a

dact-ip-lnk:loc=1203:port=fca

dact-ip-lnk:loc=1103:port=c

dact-ip-lnk:loc=1202:port=d

Dependencies

The value specified for the loc parameter must refer to one of the following cards, and the referenced card must be equipped:

E5-ENET-B card running the EROUTE, IPGWx, IPLIMx, or IPSG application
IPSM card
E5-SM4G or E5-SM8G-B card running the VSCCP application
E5-OAM card running the OAMHC application
E5-MCPM-B card
SLIC card

4916 E4916 Command invalid for hardware configuration

A valid value must be specified for the loc parameter.

2376 E2376 Cmd Rej: Specified LOC is invalid

The value specified for the port parameter must be supported by the card:

port A-E5-OAM card running OAMHC application, IPSM card, E5-MCPM-B card
port A, B- E5-ENET-B card running the EROUTE or IPLIMx application, E5-SM4G or E5-SM8G-B card running the VSCCP application
port A, B, FCA, FCB- E5-ENET-B card running the IPGWx or IPSG application
ports A, B, C and D are valid for DEIR/SIP/ENUM applications running on SLIC card

2975 E2975 Cmd Rej: Specified Port is not supported

The card at the specified location must be configured.

2144 E2144 Cmd Rej: Location invalid for hardware configuration

The card in the specified location must be Active before this command can be executed.

2387 E2387 Cmd Rej: Card is not in service

Notes

The act-ip-lnk/dact-ip-lnk commands were created as debug means - aids to turn off or disable the IP interface to troubleshoot network problems, specifically to allow the operator to troubleshoot IP network flooding issues that can cause EAGLE cards to boot repeatedly while trying to come up. These commands should NOT be used for general maintenance actions since they have not been rigorously tested and their usage should be limited to situations like described above.

Interface A/D is used for ExAP connectivity and interface B/C is used for the signaling network on the SLIC card running DEIR/SIP/ENUM applications.

Output


		  dact-ip-lnk:loc=1101:port=a

    Command Accepted - Processing

    tekelecstp 11-08-16 18:35:44 MST  EAGLE 44.0.0
    dact-ip-lnk:loc=1101:port=a
    Command entered at terminal #1.
;

    tekelecstp 11-08-16 18:35:44 MST  UNKNOWN EAGLE 44.0.0
    Deactivate IP link message sent to card. 
;

    tekelecstp 11-08-16 18:35:44 MST  EAGLE 44.0.0
    Command Completed.
;

dact-ip-lnk:loc=1103:port=c

Command Accepted - Processing

    tekelecstp 16-05-25 03:51:03 MST   EAGLE 46.4.0.0.0-69.1.0
    dact-ip-lnk:loc=1103:port=c
    Command entered at terminal #18.
;

    tekelecstp 16-05-25 03:51:03 MST   EAGLE 46.4.0.0.0-69.1.0
    Deactivate IP link message sent to card. 
;

    tekelecstp 16-05-25 03:51:03 MST   EAGLE 46.4.0.0.0-69.1.0
    Command Completed.
;

Related Topics

rtrv-ip-lnk

dbg-ddb

Use this command to display the checksum, statistics, and wild write audit (WWA) updates of dynamic database (DDB) table entries, audit a specific table, and reset the DDB statistics on the cards.

Parameters

action (mandatory)

The action taken by the command.

Range:

stats: display dynamic database statistics
aud: audit a specific table
disp: display a table entry
wwa: display any entries updated by WWA task
rststat: reset following DDB audit statistics:

Number of DDB updates
Number of consecutive DDB update in progress
Maximum DDB updates in 100 msec
Idle period
Maximum and minimum idle period

audtype (optional)

Audit type. This parameter specifies whether a unicast or multicast audit is performed.

Range:

mc: multicast
uc: unicast

Default:

mc

dpc (optional)

The destination point code value. The Route table entry corresponding to the DPC value is displayed.

Range:

p-, 000-255, *

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—p-

The asterisk value (*) is not valid for the ni subfield.

When chg-sid:pctype=ansi is specified, ni = 000 is not valid.

When chg-sid:pctype=ansi is specified, nc = 000 is not valid if ni = 001–005.

When chg-sid:pctype=ansi is specified, nc = 000 is valid if ni = 006–255.

The point code 000-000-000 is not a valid point code.

dpc/dpca/dpci/dpcn/dpcn24/dpcn16 (optional)

dpci (optional)

ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-zone-area-id).

Range:

s-, p-, ps-, 0-255, none

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s-, p-, ps

zone—0-7

area—000-255

id—0-7

The point code 0-000-0 is not a valid point code.

Enter none to delete the point code.

dpcn (optional)

ITU national destination point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the chg-stpopts:npcfmti flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).

Range:

s-, p-, ps-, 0-16383, aa-zz

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s-, p-, ps

nnnnn—0-16383

gc—aa-zz

m1-m2-m3-m4—0-14 for each member; values must sum to 14

dpcn24 (optional)

24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp). The prefix subfield indicates a private point code (prefix-msa-ssa-sp).

Range:

p-, 000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—p

msa—000–255

ssa—000–255

sp—000–255

Default:

No change to current value.

dpcn16 (optional)

16-bit ITU national point code with subfields unit number sub number area main number area (un-sna-mna). The prefix subfield indicates a private point code (prefix-un-sna-mna).

Range:: p--, 000--127; Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).; prefix--p; un---000---127; sna---000---15; mna---000---31

Default:: No change to the current value.

link (optional)

The entry in the Link table that corresponds to the specified link value.

Range:: a, b, a1 -a31, b1 - b31

loc (optional)

The location of the MTP card that is being debugged.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

lsn (optional)

Linkset name. The entry in the Linkset table that corresponds to the specified linkset name.

Range:: ayyyyyyyy

rloc (optional)

Reference card location. This parameter audits the table where the reference card is located.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

tbl (optional)

The table used as the source of the audit data.

Range:

lnk: Link table
ls: Linkset table
rte: Route table

tidx (optional)

Table index. This parameter displays the corresponding table entry.

Range:: 0 - 16000
System Default:: 0

Example

This command displays the 126th entry in the Link table.

dbg-ddb:loc=1105:tbl=lnk:action=disp:tidx=126

This command displays the entry in the Link table corresponding to link=a and rloc=1107.

dbg-ddb:loc=1105:tbl=lnk:action=disp:rloc=1107:link=a

This command audits the Link table in multicast mode.

dbg-ddb:loc=1105:tbl=lnk:action=aud:audtype=mc

This command audits the Link table in unicast mode.

dbg-ddb:loc=1105:tbl=lnk:action=aud:audtype=uc

This command audits the Link table at the card location 1105 using the reference card 1107.

dbg-ddb:loc=1105:tbl=lnk:action=aud:audtype=uc:rloc=1107

This command displays the statistics of a specified card.

dbg-ddb:loc=1201:action=stats

This command displays the WWA entries on a specified card.

dbg-ddb:action=wwa:loc=1201

This command resets the statistics of a specified card.

dbg-ddb:action=rststat:loc=2100

This command resets the statistics of all active MTP cards.

dbg-ddb:action=rststat

Dependencies

The dpc, tidx, lsn, and rloc parameters cannot be specified together in the command.

The dpc, tidx, lsn, and link parameters cannot be specified together in the command.

The action=disp and tbl=rte parameters must be specified before the dpc parameter can be specified.

The action=disp and tbl=ls parameters must be specified before the lsn parameter can be specified.

The action=disp and tbl=lnk parameters must be specified before the link parameter can be specified.

The action=disp parameter must be specifed before the tidx parameter can be specified.

The action= aud parameter must be specified before the audtype parameter can be specified.

The action=disp and tbl=lnk parameters or the action=aud and audtype=uc parameters must be specified before the rloc parameter can be specified.

If the action parameter has a value of wwa, stats, or rststat, then the loc parameter is the only other parameter that can be specified.

2155 E2155 Cmd Rej: Invalid parameter combination specified

If the action=disp and tbl=lnk parameters are specified, then the rloc and link parameters must be specified together in the command.

4785 E4785 Cmd Rej: RLOC and LINK parameter combination must be specified

The card location specified by the loc or rloc parameter must be equipped.

2101 E2101 Cmd Rej: Card location is unequipped

The value specified for the loc or rloc parameter must indicate an MTP card.

2212 E2212 Cmd Rej: Invalid card type for this command

The status of the card at the location specified by the loc or rloc parameter must be active.

4259 E4259 Cmd Rej: Target card is not in Active state

The linkset specified by the lsn parameter must already exist in the Linkset table.

2303 E2303 Cmd Rej: Unknown LSN

The link specified by the link parameter must already be equipped.

2373 E2373 Cmd Rej: Link is unequipped in the database

The value specified for the dpc parameter must already exist in the Route table.

2417 E2417 Cmd Rej: Point code does not exist in the routing table

The Link table is corrupt or cannot be found.

2103 E2103 Cmd Rej: Failed reading the link table

The value specified for the dpc parameter must be a full point code, network point code, or a cluster point code.

2886 E2886 Cmd Rej: DSTN address must be a full, network or cluster PC

Values of 1113 - 1118 cannot be specified for the loc or rloc parameters.

2154 E2154 Cmd Rej: Card slot reserved by system

If the action parameter has a value of disp, aud, stats, or wwa, then the loc parameter must be specified.

If the action=aud parameter and the rloc parameter are specified, then the audtype parameter must be specified.

If the action parameter has a value of disp or aud, then the tbl parameter must be specified.

2379 E2379 Cmd Rej: Missing parameter

The J7 support feature must be enabled before the opcn16/dpcn16 parameters can be specified.

2691 E2691 Cmd Rej: J7 Support Feature must be enabled.

Notes

For a multicast audit, the card that receives the message sends the audit request to all other MTP cards simultaneously. For a unicast audit, the card that receives the message sends the audit request to another MTP card, which sends the request to next MTP card, etc. This process continues until the last MTP card in the system receives the request.

A maximum of the last 10 entries of WWA updates are displayed.

Output

A maximum of 20 entries with mismatched card values can be displayed as necessary.

If mismatched card entries occur, the SeqNo field can be used to correlate the entries between two cards (e.g.SeqNo: 1 of card 1 can be compared against SeqNo: 1 of card 2.)

dbg-ddb:loc=1104:action=disp:tbl=ls:tidx=1


    tekelecstp 09-10-15 12:37:37 EST  EAGLE5 41.1.0
    dbg-ddb:loc=1104:action=disp:tbl=ls:tidx=1
    Command entered at terminal #4. 
;

    tekelecstp 09-10-15 12:37:37 EST  EAGLE5 41.1.0
    User Message sent to location 1104. 
;

    tekelecstp 09-10-15 12:37:37 EST  EAGLE5 41.1.0
    [SeqNo: 0] [1104] [Linkset:1] Chksum h'1624 at h'28e84a (138 bytes)
    Assign:1 Avail:0 APC:   001-001-002 ITUNVar:0 
;

dbg-ddb:loc=1104:action=disp:tbl=lnk:tidx=1


    tekelecstp 09-10-15 12:37:37 GMT  EAGLE5 41.1.0
    dbg-ddb:loc=1104:action=disp:tbl=lnk:tidx=1
    Command entered at terminal #4. 
;

    tekelecstp 09-10-15 12:37:37 GMT  EAGLE5 41.1.0
    User Message sent to location 1104. 
;

    tekelecstp 09-10-15 12:37:37 GMT  EAGLE5 41.1.0
    [SeqNo: 0] [1104] [Link:x1] Chksum h'da8d at h'2877ce (14 bytes)
    PortId:h'1e6 (Card:1104 Link h'0)
    Slc:0 Stat:h'2 LsId:h'0 Class:0
    Status:Fail 
;

dbg-ddb:loc=1104:action=aud:tbl=lnk:audtype=mc


    tekelecstp 09-10-15 13:40:38 GMT  EAGLE5 41.1.0
    dbg-ddb:loc=1104:action=aud:tbl=lnk:audtype=mc
    Command entered at terminal #4. 
;

    tekelecstp 09-10-15 13:40:38 GMT  EAGLE5 41.1.0
    User Message sent to location 1104. 
;

    tekelecstp 09-10-15 13:40:38 GMT  EAGLE5 41.1.0
    [1104] Bcast:Card->Sys (Tbl 0) MTPCards:h'2 Reply:h'2 Mismatch:h'0 
;

dbg-ddb:loc=1104:action=aud:tbl=lnk:audtype=uc


    tekelecstp 09-10-15 16:37:11 GMT  EAGLE5 41.1.0
    dbg-ddb:loc=1104:action=aud:tbl=lnk:audtype=uc
    Command entered at terminal #4. 
;

    tekelecstp 09-10-15 16:37:11 GMT  EAGLE5 41.1.0
    User Message sent to location 1104. 
;

    tekelecstp 09-10-15 16:37:11 GMT  EAGLE5 41.1.0
    [1104]Card->System (Tbl:0) Successful System Audit Completed 
;

This example shows the output when multiple mismatch entries occur between two cards:

dbg-ddb:loc=1205:rloc=1207:action=aud:tbl=rte:audtype=uc


    tekelecstp 10-01-28 16:37:11 GMT  EAGLE5 42.0.0
    dbg-ddb:loc=1205:rloc=1207:action=aud:tbl=rte:audtype=uc
    Command entered at terminal #4. 
;   

    tekelecstp 10-01-28 16:37:11 GMT  EAGLE5 42.0.0
    User Message sent to location 1205. 
;

    tekelecstp 10-01-28 16:37:11 GMT  EAGLE5 42.0.0
    Card[1205]->card[1207] (Tbl:0) TblAuditDone:TotalMisses:h'2 FirstMiss:h'0 
;

    tekelecstp 10-01-28 16:37:11 GMT  EAGLE5 42.0.0
    [SeqNo: 1] [1205] [Route:h'0] Chksum h'320b at h'8fc3b0 (75 bytes)
    PC: 001-001-001 LstRt:0 CmbRt:6 Dyn:h'1 TFC:0
    Xlst:0 MOBR:0 NAdj:1 3 3 3 3 3 NmTFR:0 PrevSt:1 
;

    tekelecstp 10-01-28 16:37:11 GMT  EAGLE5 42.0.0
    [SeqNo: 1] [1205] nway: 0 cost_grp(0-5): c7 c6 c6 c6 c6 c6
    rte_used(0-5): c0 36 36 36 36 36
    curr_cost_grp: 0 prev_cost_grp 0
    SRT:h'88079c (28 bytes) AKT:h'8bb43c (12 bytes) 
;

    tekelecstp 10-01-28 16:37:11 GMT  EAGLE5 42.0.0
    [SeqNo: 2] [1205] [Route:h'1] Chksum h'c96e at h'8fc3fb (75 bytes)
    PC: 001-001-002 LstRt:0 CmbRt:6 Dyn:h'1 TFC:0
    Xlst:0 MOBR:0 NAdj:1 3 3 3 3 3 NmTFR:0 PrevSt:1 
;

    tekelecstp 10-01-28 16:37:11 GMT  EAGLE5 42.0.0
    [SeqNo: 2] [1205] nway: 0 cost_grp(0-5): c7 c6 c6 c6 c6 c6
    rte_used(0-5): c0 36 36 36 36 36
    curr_cost_grp: 0 prev_cost_grp 0
    SRT:h'8807b8 (28 bytes) AKT:h'8bb448 (12 bytes) 
;

    tekelecstp 10-01-28 16:37:11 GMT  EAGLE5 42.0.0
    [SeqNo: 1] [1207] [Route:h'0] Chksum h'cecc at h'9688ea0 (243 bytes)
    PC: 001-001-001 LstRt:0 CmbRt:6 Dyn:h'1 TFC:0
    Xlst:0 MOBR:0 NAdj:1 3 3 3 3 3 NmTFR:0 PrevSt:1 
;

    tekelecstp 10-01-28 16:37:11 GMT  EAGLE5 42.0.0
    [SeqNo: 1] [1207] nway: 0 cost_grp(0-5): c8 c6 c6 c6 c6 c6
    rte_used(0-5): c0 46 36 36 36 36
    curr_cost_grp: 0 prev_cost_grp 0
    SRT:h'95148e0 (28 bytes) AKT:h'9575980 (12 bytes) 
;

    tekelecstp 10-01-28 16:37:11 GMT  EAGLE5 42.0.0
    [SeqNo: 2] [1207] [Route:h'1] Chksum h'662f at h'9688f93 (243 bytes)
    PC: 001-001-002 LstRt:0 CmbRt:6 Dyn:h'1 TFC:0
    Xlst:0 MOBR:0 NAdj:1 3 3 3 3 3 NmTFR:0 PrevSt:1 
;
 
   tekelecstp 10-01-28 16:37:11 GMT  EAGLE5 42.0.0
    [SeqNo: 2] [1207] nway: 0 cost_grp(0-5): c8 c6 c6 c6 c6 c6
    rte_used(0-5): c0 46 36 36 36 36
    curr_cost_grp: 0 prev_cost_grp 0
    SRT:h'95148fc (28 bytes) AKT:h'957598c (12 bytes) 
;

dbg-ddb:action=wwa:loc=1301


    tekelecstp 09-10-12 17:37:11 GMT  EAGLE5 41.1.0
    dbg-ddb:action=wwa:loc=1301
    Command entered at terminal #10. 
;

    tekelecstp 09-10-12 17:37:11 GMT  EAGLE5 41.1.0
    User Message sent to location 1301. 
;

    tekelecstp 09-10-12 17:37:11 GMT  EAGLE5 41.1.0
    DDB WWA REPORT (LOC = 1301)
            WILD WRITE AUDIT UPDATED (1) ENTRIES:
            TIME STAMP             TABLE      ENTRY_IDX  ORIG CHKSUM  UPD CHKSUM
        1.  09-10-12 17:35:02:586  RTE        0          H'41880000   H'00000000 
;

dbg-ddb:action=stats:loc=1201


    tekelecstp 09-10-03 17:37:11 GMT  EAGLE5 41.1.0
    dbg-ddb:action=stats:loc=1201
    Command entered at terminal #10. 
;

    tekelecstp 09-10-03 17:37:11 GMT  EAGLE5 41.1.0
    User Message sent to location 1201. 
;

    tekelecstp 09-10-03 17:37:11 GMT  EAGLE5 41.1.0
    DDB STATISTICS
        LOC                                             : 1201
        CARD STATUS       (DDL)                         : [CROSSLOADED]
                          (DDB)                         : [INITIALIZED]
        IN UPDATE STATUS  (DDB CHECKSUM)                : [FALSE]
                          (TSRC)                        : [IDLE]
        SUCCESIVE TIMES CARD REPORTED (IN UPDATE)       : 0
        DDB UPDATES                                     : 2000
        MAXIMUM UPDATES PER 100ms                       : 900
        DDB IDLE PERIOD:                                : 03:12:30:20:50
        MAXIMUM IDLE PERIOD                        : 02:12:30:20:50
        MINIMUM IDLE PERIOD                        : 01:04:40:10:80 
        NUMBER OF WWA UPDATED ENTRIES                   : 4 
;

dbg-ddb:action=wwa:loc=1201


    tekelecstp 09-10-21 17:37:11 GMT  EAGLE5 41.1.0
    dbg-ddb:action=wwa:loc=1201
    Command entered at terminal #10. 
;

    tekelecstp 09-10-21 17:37:11 GMT  EAGLE5 41.1.0
    User Message sent to location 1201. 
;

    tekelecstp 09-10-21 17:37:11 GMT  EAGLE5 41.1.0
    DDB WWA REPORT (LOC = 1201)
            WILD WRITE AUDIT UPDATED (NO) ENTRIES: 
;

Legend

WWA—Wild Write Audit
DDB—Dynamic Database
Time stamp—Card time stamp when the checksum was detected and updated by wild write audit. The time stamp is inYY-MM-DD hh:mm:ss:msec format.
TABLE—Table where the checksum is being performed
Entry Idx—Index of entry that is updated by wild write audit
Orig Chksum—Original Checksum
Upd Chksum—Checksum after update by wild write audit
Idle Period—Time elapsed, in milliseconds, since the last DDB update was received by this card. All idle periods are displayed indd:hh:mm:ss:msec format.
Number of WWA Updated Entries—Number of entries updated by the WWA

Related Topics

rept-stat-ddb

disp-bip

Use this command to display the Board Identification PROM (BIP) hex and ASCII data for the specified card type and location. The PROM data consists of the board ID, part number, revision, date of manufacture, power, serial number, software match ID, and check sums.

Parameters

loc (mandatory)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1113, 1115, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110

type (optional)

The board type to be displayed.

Range:

mbd: Displays the main assembly.

Example

This example displays the BIP data for the main assembly of the specified card location.

disp-bip:loc=1105

Dependencies

The value of the loc parameter cannot specify the location of a fixed disk or removable drive.

2242 E2242 Cmd Rej: Destination card invalid

Notes

None.

Output

This example displays the BIP data for the main assembly:

disp-bip:loc=1105


    tekelecstp 10-03-30 20:24:41 IST  EAGLE 42.0.0
    Board Identification PROM Dump  Location: 1105 - MDB  Packet: 1
    -------------------------------------------------------------------------
    0000  42 49 44 30 31 2c 50 4e 38 37 30 2d 32 32 31 32  BID01,PN870-2212
    0010  2d 30 33 2e 45 2c 53 4d 45 47 2e 30 30 31 2c 44  -03.E,SMEG.001,D
    0020  53 32 30 30 38 2e 31 34 2e 43 2e 31 30 32 30 38  S2008.14.C.10208
    0030  31 34 37 30 39 39 2c 50 57 36 34 36 2c 43 53 32  147099,PW646,CS2
    0040  32 35 00 00 01 26 07 ff 01 00 26 00 80 14 21 ff  25...&....&...!.
    0050  ff ff 01 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    0060  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    0070  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
;

    tekelecstp 10-03-30 20:24:41 IST  EAGLE 42.0.0
    Board Identification PROM Dump  Location: 1105 - MDB  Packet: 2
    -------------------------------------------------------------------------
    0000  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0010  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0020  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0030  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0040  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0050  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0060  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0070  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................ 
;

    tekelecstp 10-03-30 20:24:41 IST  EAGLE 42.0.0
    Board Identification PROM Dump  Location: 1105 - MDB  Packet: 3
    -------------------------------------------------------------------------
    0000  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0010  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0020  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0030  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0040  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0050  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0060  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0070  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................ 
;
  
    tekelecstp 10-03-30 20:24:41 IST  EAGLE 42.0.0
    Board Identification PROM Dump  Location: 1105 - MDB  Packet: 4
    -------------------------------------------------------------------------
    0000  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0010  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0020  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0030  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0040  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0050  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0060  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
    0070  ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................ 
;

Related Topics

disp-bp

Use this command to display currently active breakpoints in the communication and application processors.

Parameters

card (optional)

This parameter specifies the card location, in the form of GPLID–Subsystem ID.

Range: GPLID-Subsystem ID

GPLID: atmhc, deirhc, erthc, glshc, hipr2, ipghc, iplhc, ipsg, ipshc, mcphc, oamhc, pktgen, sccphc, siphc, ss7hc, utility
Subsystem ID: a, b, act, stb, all

The oamhc GPL can be specified with any of the subsystem IDs. For all other GPLs, only the all subsystem ID is valid.

imt (optional)

The IMT address of the card.

Range:: 0 - 254

loc (optional)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115

proc (optional)

This parameter specifies the processor type.

Range:

appl: Application processor
com: Communication processor

Default:

appl

ueng (optional)

The microengine number.

This parameter is valid only on IXP-based cards. If this parameter is not specified for IXP-based cards, then the command is assumed to be intended for the ARM processor in the IXP chip.

Range:: 0 - 5

Example

disp-bp:loc=1109:ueng=3

Dependencies

The loc, imt, or card parameter must be specified.

2214 E2214 Cmd Rej: Missing parameter - CARD, LOC, or IMT

Only one of the loc, imt, and card parameters can be specified in the command.

2217 E2217 Cmd Rej: More than one of CARD, LOC, and IMT specified

The imt parameter allows this command to be entered for a card that has not been configured in the system.

N/A N/A

The ueng parameter can be specified only for IXP-based cards.

4151 E4151 Cmd Rej: UENG parameter is invalid for this card

The oamhc GPLID accepts all subsystem values; all other GPLIDs accept only the all subsystem value.

N/A N/A

The card location specified by the loc parameter must be in the database.

2101 E2101 Cmd Rej: Card location is unequipped

Values of 1114, 1116, 1117, and 1118 cannot be specified for the loc parameter.

2212 E2212 Cmd Rej: Invalid card type for this command

Notes

None

Output

These examples are for x86-based cards:

disp-bp:card=ss7ansi-all


    rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0 
    SDS Installed Breakpoint Report from IMT Address H'00f4  
    Brkpoint-Addr Memory-Dump-Addr Condition-1 Condition-2 Repeat-Count  
    ------------- ---------------- ----------- ----------- ------------ 
    H'003a-H'0001                  ANY         ANY               0 

    rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0  
    SDS Installed Breakpoint Report from IMT Address H’000a  
    BP Address Memory-Dump Address       Conditions         Rpt Ct Ind  
    ---------- ------------------------- ------------------ ------ --- 
    H’0000a974 H’000c030c                1- ANY               3     1
       Code Breakpoint                   2- ANY 
    H’0000a975                           1- ANY              PERM   0
       Data Write - WORD                 2- ANY 
    H’0000a976                           1- ANY               15    0
       Any Access - DWORD                2- ANY 
    H’0000a977                           1- ANY              PERM   0
       Data Read - BYTE                  2- ANY 

    rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0 
    80386/80486 Debug Registers in Use: DR0 DR2 DR3 
;

disp-bp:card=vsccp-all:


    rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0 
    SDS Installed Breakpoint Report from IMT Address H'0005 
    BP Address Memory-Dump Address       Conditions        Rpt Ct Ind 
    ---------- ------------------------- ----------------- ------ --- 
    H'0000a974                           1- ANY            1       0 
    Code Breakpoint                      2- ANY 
;

These examples are for IXP-based cards:

disp-bp:loc=1109


    tekelecstp 05-01-10 13:58:45 GMT EAGLE5 33.0.0 
    SDS Installed Breakpoint Report from IMT Address H'00ff 

    BP Address Memory-Dump Address Conditions            Rep  Ind CPU 
    ---------- ------------------- --------------------- ---- --- ------ 
    H'000401000 R11+H'0000ffff     1- R15 > H'ffffffff     2   0    ARM
       Any Access -                2- R0 <= H'0000ffff
       Data value: H'00000000 Data Mask: H'ffffffff

disp-bp:loc=1109:ueng=3


    tekelecstp 05-01-10 13:58:45 GMT EAGLE 33.0.0 
    SDS Installed Breakpoint Report from IMT Address H'00ff 

    BP Address Memory-Dump Address Conditions            Rep  Ind CPU 
    ---------- ------------------- --------------------- ---- --- ------ 
    H'00235000 H'00020044          1- ANY                PERM 1   UENG 3
       CODESW Breakpoint           2- ANY                         CTX 2 
;

Related Topics

disp-disk-dir

Use this command to display the DOS directory on the specified disk. This command can display the creation date for each file or for selected files and applies to fixed disks and removable drives.

Note:

This command can be used to verify that the correct version of a file is on the disk.

Parameters

file (optional)

The name of the file to be displayed.

Range:: zzzzzzzzzzzz
1–12 ASCII characters
Default:: All files are displayed

loc (optional)

The card location in the system.

Range:

1114: TDM
1116: TDM
1117: Removable cartridge drive
1113: Latched USB port
1115: Latched USB port

prtngrp (optional)

Partition group. The disk partition group to be displayed.

Range:

active
inactive

Default:

active

src (optional)

Source. The identification of the disk containing the files to be displayed.

Range:

fixed: The fixed disk
remove: The removable drive in the latched USB port of the E5-MCAP
usb: The plug-in USB flash drive in the flush-mounted USB port of the E5-MCAP

Default:

The fixed disk

Example

disp-disk-dir:loc=1117:file="dms.cfg"

disp-disk-dir:src=remove:file="fta"

disp-disk-dir:src=remove:file="*.*"

Dependencies

Valid filenames must be in the format filename.extension with the following requirements:

File name—1–8 ASCII Characters
Extension—0–3 ASCII Characters

2314 E2314 Cmd Rej: Invalid filename entered

Wildcards (asterisks) are allowed when the wildcard pattern is enclosed in parentheses.

*—Matches all characters in either filename or extension
?—Matches one character in either filename or extension
file=”*.*”—Matches all files on disk
file=”*.tbl”—Matches all files on disk with .tbl as the extension

2314 E2314 Cmd Rej: Invalid filename entered

The src parameter must be specified.

4913 E4913 Cmd Rej: Disk parameter required for specified location

The 1113 and 1115 locations are used by E5-MCAP cards. The 1114 and 1116 locations are used by E5-TDM cards.

2144 E2144 Cmd Rej: Location invalid for hardware configuration

A removable drive must be inserted in the slot indicated by the value specified for the loc or src parameter.

2165 E2165 Cmd Rej: Removable drive not inserted

The card specified by the loc parameter must be connected to at least one IMT bus.

2269 E2269 Cmd Rej: Unable to communicate with card at location

Notes

None

Output


		  disp-disk-dir


    lnpstp 01-03-30 15:52:04 EST  Rel 28.1.0
    DISP-DISK-DIR, Loc=1116, Device = FIXED, Dir = :\
    Filename  Ext        Length   Last  Modified      Cluster           LBA
    DMS       CFG         16384   00-08-01 18:45            2           573
    :

    File(s) : 175   Bytes : 457956761
    Volume : FIXED DISK
    Bytes free : 73654887
    Disk Size (MB) : 2014 
;

 disp-disk-dir:loc=1117


    lnpstp 01-03-30 15:52:46 EST  Rel 28.1.0

 disk-disk-dir:loc=1117:file="dms1024.cfg"


    DISP-DISK-DIR, Loc=1117, Device = REMOVE, Dir = :\
    Filename  Ext        Length   Last  Modified      Cluster           LBA
    DMS1024   CFG         16384   00-08-01 15:48            2           339
    :
    File(s) : 72   Bytes : 192883124
    Volume : SYSTEM DISK
    Bytes free : 956339788
    Disk Size (MB) : 1096 
;

 disp-disk-dir:file=ttserv.tbl


    lnpstp 01-03-30 15:53:09 EST  Rel 28.1.0
    DISP-DISK-DIR, Loc=1116, Device = FIXED, Dir = :\
    Filename  Ext        Length   Last  Modified      Cluster           LBA
    TTSERV    TBL          8192   00-08-01 18:45         2731         44237

    File(s) : 1   Bytes : 8192
    Volume : FIXED DISK
    Bytes free : 73654887
    Disk Size (MB): 2014 
;

 disp-disk-dir:loc=1116


    eaglestp 10-03-06 15:53:09 EST TTTT PPP  EAGLE 42.0.0
    DISP-DISK-DIR, Loc=1116, Device = FIXED, Dir = :\
    Filename  Ext        Length   Last  Modified      Cluster           LBA
    DMS       CFG         16384   08-07-97 11:00            2           573
    OAM       ELF       3145728   08-07-97 11:00            4           605
    TOAM      ELF       3145728   08-07-97 11:00          388          6749
    SS7       ELF       1048576   08-07-97 11:00          772         12893
    TSS7      ELF       1048576   08-07-97 11:00          900         14941
    CCS7ITU   ELF       1048576   08-07-97 11:00         1284         21085
    .
    .
    .
    LNP_LRN   BKP       3072096   08-07-97 11:00        38963        623949
    LNP_MR    BKP       1679392   08-07-97 11:00        39339        629965
    LNP_NPA   BKP       5120096   08-07-97 11:00        39545        633261
    LNP_4DIG  BKP     128000064   08-07-97 11:00        40171        643277
    ACG_MIC   BKP        187712   08-07-97 11:00        55797        893293
    LNP_CHCK  BKP        197378   08-07-97 11:00        55820        893661
    LNP_DBMM  BKP        801600   08-07-97 11:00        55845        894061
    TRBLTX    BKP         63980   08-07-97 11:00        55943        895629
    MTT       BKP        384000   08-07-97 11:00        55951        895757
    2201800   REL          2048   08-07-97 11:00        55998        896509

    File(s) : 175   Bytes : 457956761
    Volume : FIXED DISK
    Bytes free : 73654887
    Disk Size (MB) : 507
    Largest Free Space : 73654887 
;

This example shows the output when an E5-MCAP card is used:

 disp-disk-dir:loc=1113:src=remove


    e5oam 09-01-20 22:24:12 EST  EAGLE 40.1.0     
    DISP-DISK-DIR  Loc=1113  Dev = REMOVE    
    Filename  Ext            Length    
    DMS1024   CFG             32768    
    TATMANSI  ELF           3145728    
    TATMHC    ELF           5242880    
    TATMITU   ELF           3145728    
    TBLBEPM   ELF           3145728    
    TBLBIOS   ELF           3145728    
    TBLBSMG   ELF           3145728    
    TBLCPLD   ELF           3145728    
    TBLDIAG   ELF           3145728    
    TBLDIAG6  ELF           3145728
    ...
    SMEAS_ST  SYS             12228
    UIMLOG    SYS          11263947
    SYSREL    SYS               949
    MTT       BKP            384000
    TRBLTX    BKP             96000
    FEATCTRL  BKP            128000
    ASSYPWR   BKP              8016
    TS30100   REL              5120
    BLMCAP    TAR          13721600
    File(s) : 178    Bytes : 437596655    Disk Size (MB) : 1972;

Legend

Filename—Name of the file in the directory
Ext—Extension of the file name (for example, for the file MFC.BIN, MFC is the file name and BIN is the extension of the file name)
Length—Amount of space, in bytes, the file occupies on the disk
Last Modified—Date and time the file was changed
Cluster—A 2-byte, 16-digit binary number that represents the first section of the disk occupied by the file
LBA—Starting logical block address that corresponds to the cluster
File(s)—Number of files on the disk that match the search criteria
Bytes—Amount of space, in bytes, the displayed files occupy on the disk
Volume—11-character name for the disk
Bytes free—Number of bytes that are available on the disk for file storage
Disk Size—Total capacity of the specified disk

Related Topics

disp-disk-stats

Use this command to display the disk performance statistics.

Note:

The OAMs maintain disk read/writer access times as well as per table and per application statistics on the number of disk accesses and cache accesses. Per application and per table statistics that have zero values are not displayed if an application ID or table ID is not specified; only nonzero statistics are displayed in the default report.

Parameters

loc (mandatory)

The card location in the system.

Range:: 1113, 1115

applid (optional)

Application ID. The application IDs used to define tasks.

Range:: 0 - 255
Default:: all

tblid (optional)

Table ID. The table IDs used to define tables.

Range:: 0 - 1023
Default:: all

Example

disp-disk-stats:loc=1113:applid=29

disp-disk-stats:loc=1113:applid=93

disp-disk-stats:loc=1113

Dependencies

The specified card location must contain a card that is running an OAM (1113 or 1115).

3291 E3291 Cmd Rej: Card location specified must be an OAM card

GPSM-II and E5-MCAP cards cannot co-exist in the system.

3084 E3084 Cmd Rej: Both OAM cards must be of the same type

Notes

None

Output

disp-disk-stats:loc=1113:applid=29


    rlghncxa03w 01-03-01 14:14:05 EST  Rel 28.1.0 

    Disk Performance Statistics Report:

                  Cache Read     Disk Read    Cache Write   Disk Write
      Appl Id         Hits        Accesses        Hits       Accesses 
    -----------   -----------   -----------   -----------   -----------
            29           113            23            25            40 

Command Completed.

disp-disk-stats:loc=1113:applid=93


    tekelecstp 01-06-01 14:14:05 EST Rel 28.1.0
 
    Disk Performance Statistics Report:
                  Cache Read     Disk Read    Cache Write   Disk Write
      Appl Id         Hits        Accesses        Hits       Accesses
    -----------   -----------   -----------   -----------   -----------
            93             0             0             0             0
    
    Command Completed. 
;

disp-disk-stat:loc=1113


    rlghncxa03w 01-03-01 14:14:05 EST  Rel 28.1.0

    Disk Performance Statistics Report:

                  Cache Read     Disk Read    Cache Write   Disk Write
      Appl Id         Hits        Accesses        Hits       Accesses 
    -----------   -----------   -----------   -----------   -----------
            29           113            23            25            40
           120            12           223           225           361

                 Cache Read     Disk Read    Cache Write   Disk Write
      Table Id        Hits        Accesses        Hits       Accesses 
    -----------   -----------   -----------   -----------   -----------
           185            12           223           225           361
           201           113            23            25            40
           
                 Total Cache   Total Disk    Total Cache   Total Disk
                  Read Hits       Reads       Write Hits     Writes
                  -----------   -----------   -----------   -----------
                         125           246           250           401

                             Disk Access Times (microseconds)
                    Minimum       Maximum       Average     Access Type
                  -----------   -----------   -----------   -----------
                        1260         31121          6380          Read
                        1215         31090          6350         Write 

Command Completed. 
;

Related Topics

clr-disk-stats

disp-mem

Use this command to display memory in communication and application processors. This display is in byte format.

Parameters

addr (optional)

The address in the form of segment–offset.

Range:

segment-offset

segment— h'00-h'ffff

offset— h'00-h'ffff

bc (optional)

Byte count. The number of data bytes to display.

Range:: 1 - 65535
Default:: 96

card (optional)

Card location. The card location in the form of GPLID–Subsystem ID.

Range:

GPLID-Subsystem ID

GPLID— atmhc, deirhc, erthc, glshc, hipr2, ipghc, iplhc, ipsg, ipshc, mcphc, oamhc, pktgen, sccphc, siphc, ss7hc, utility

Subsystem ID— a, b, act, stb, all

dformat (optional)

The memory dump format.

Range:

byte
word
dword

Default:

byte

imt (optional)

The IMT address.

Range:: 0 - 254

loc (optional)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115

paddr (optional)

The physical offset of the memory address.

Range:

h’00–h’ffffffff

proc (optional)

The processor type.

Range:

appl: Application processor
com: Communication processor

Default:

appl

Example

disp-mem:loc=1204:paddr=h’103abc:bc=8:dformat=word

disp-mem:loc=1204:paddr=h’103abc:bc=8:dformat=dword

disp-mem:card=ss7ansi-all:addr=h'03a-h’001:bc=8

Dependencies

The loc, imt, or card parameter must be specified.

2214 E2214 Cmd Rej: Missing parameter - CARD, LOC, or IMT

Only one of the loc, imt, and card parameters can be specified in the command.

2217 E2217 Cmd Rej: More than one of CARD, LOC, and IMT specified

The card location specified by the loc parameter must be in the database.

2101 E2101 Cmd Rej: Card location is unequipped

All of the subsystem values can be specified with the oamhc GPLID. The other GPLID values can be specified only with the all subsystem value.

2208 E2208 Cmd Rej: ALL only qualifier allowed with given card type

Card locations 1114, 1116, 1117, and 1118 are not valid for memory commands.

2212 E2212 Cmd Rej: Invalid card type for this command

The GPL specified in the card parameter must be supported.

2212 E2212 Cmd Rej: Invalid card type for this command

The addr and paddr parameters cannot be specified together in the command.

2694 E2694 Cmd Rej: Invalid combination of ADDR and PADDR specified

Notes

The imt parameter allows this command to be entered for a card that has not been configured in the system.

Output

disp-mem:loc=1204:paddr=h’103abc:bc=8:dformat=word


    rlghncxa03w 01-03-22 21:13:50 EST Rel 28.1.0 
    SDS Memory Dump from IMT Address H'000a 
    Source-Address = H'00103abc     Length = 8 bytes 
    0000 ffff 00ff 00ff 0000                ........ 
;

disp-mem:card=psm-a:addr=h'03a-h’001:bc=8


    rlghncxa03w 01-03-22 21:13:50 EST Rel 28.1.0
    SDS Memory Dump from IMT Address H'00f6
    Source-Address = H'003a0001      Length = 8 bytes
    0000 04 0d 3d 1c 04 0d 3d 1c             ..=...=. 
;

Related Topics

set-mem

disp-trace

Use this command to display trace entries.

Parameters

traceid (optional)

Trace ID. The trace entry to be displayed.

Range:: 1 - 10

Example

disp-trace

disp-trace:traceid=5

Dependencies

A valid value must be specified for the traceid parameter.

2017 E2017 Cmd Rej: <parm_desc> is out of range, <min>..<max> - <parm>

None

N/A N/A

Output

disp-trace


    stdcfg2b 07-10-05 12:55:32 EST  EAGLE 37.5.0
    Trace Request 1:
    CARD=         SS7ANSI    OPC=          001-001-001    
    TRACE DISPLAY COMPLETE. 
;

Related Topics

dlt-bp

Use this command to delete breakpoints in the communication or application processors.

Parameters

addr (optional)

The address in the form of segment–offset.

Range:

segment-offset

segment— h’00–h’ffff

offset— h’00–h’ffff

card (optional)

The card location in the form of GPLID–Subsystem ID.

Range:

GPLID-Substystem ID

GPLID— atmhc, deirhc, erthc, glshc, hipr2, ipghc, iplhc, ipsg, ipshc, mcphc, oamhc, pktgen, sccphc, siphc, ss7hc, utility

Subsystem ID— a, b, act, stb, all

The OAMHC GPL can be specified with any of the subsystem IDs. For all other GPLs, only the all subsystem ID is valid.

imt (optional)

The IMT address of the card.

Range:: 0 - 254

loc (optional)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115

paddr (optional)

The physical offset of the memory address.

Range:

: h’00–h’ffffffff

proc (optional)

The processor type.

Range:

appl: Application processor
com: Communication processor

Default:

appl

ueng (optional)

The microengine number.

Note:

This parameter is valid only on IXP-based cards. If this parameter is not specified for IXP-based cards, then the command is assumed to be intended for the ARM processor in the IXP chip.

Range:: 0 - 5

Example

dlt-bp:loc=1209:ueng=2

dlt-bp:card=hipr2-all

dlt-bp:loc=6312

Dependencies

The loc, imt, or card parameter must be specified.

2214 E2214 Cmd Rej: Missing parameter - CARD, LOC, or IMT

Only one of the loc, imt, and card parameters can be specified in the command.

2217 E2217 Cmd Rej: More than one of CARD, LOC, and IMT specified

The ueng parameter can be specified only for IXP-based cards.

4151 E4151 Cmd Rej: UENG parameter is invalid for this card

The card location specified by the loc parameter must be in the database.

2101 E2101 Cmd Rej: Card location is unequipped

Values of 1114, 1116, 1117, and 1118 cannot be specified for the loc parameter.

2212 E2212 Cmd Rej: Invalid card type for this command

All of the subsystem values can be specified with the oamhc GPLID. The other GPLID values can be specified only with the all subsystem value.

2208 E2208 Cmd Rej: ALL only qualifier allowed with given card type

The addr and paddr parameters cannot be specified together in the command.

2694 E2694 Cmd Rej: Invalid combination of ADDR and PADDR specified

Notes

The imt parameter allows this command to be entered for a card that has not been configured in the system.

Output

dlt-bp:card=oam-all:proc=com


    Command Accepted - Processing

    tekelecstp 97-01-20 19:21:10 EST Rel 37.0.0
    dlt-bp:card=oam-all:proc=com
    Command entered at terminal #1. 
;

Related Topics

dlt-ee-flt

Use this command to delete an Eagle Eyes Filter from the Eagle Eyes Filter (EE FLT) table. The EE FLT entry consists of a Filter ID and Filter specific data. It can be used to delete a filter only when it is not associated with any card.

Parameters

fltid (mandatory)

Eagle Eyes Filter ID.

Range:: 1-200

Example

dlt-ee-flt:fltid=20

Dependencies

The specified Filter ID must exist in the EE FLT table.

2827 E2827 Cmd Rej: Filter not present

The Eagle Eyes Filter table must be available.

2813 E2813 Cmd Rej: Unable to read EE Filter table

The specified filter should not be associated with any network card.

2858 E2858 Cmd Rej: EE Filter associated to network card

Notes

None.

Output

dlt-ee-flt:fltid=3


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    EE FLT table is (2 of 200) 1% full
    DLT-EE-FLT: MASP A - COMPLTD 
;

Related Topics

dlt-trace

Use this command to delete provisioned MSU tracing criteria from the database.

Parameters

traceid (optional)

Trace ID. Identifier of the trace entry to be deleted.

Range:: 1 - 10

Example

dlt-trace:traceid=5

dlt-trace

Dependencies

Only values between 1 and 10 are valid for the traceid parameter.

2017 E2017 Cmd Rej: <parm_desc> is out of range, <min>..<max> - <parm>

None

N/A N/A

Output

dlt-trace:traceid=1


    stdcfg2b 07-10-05 13:03:29 EST  EAGLE 37.5.0
    dlt-trace:traceid=1
    Command entered at terminal #4. 

;

Related Topics

ent-bp

Use this command to add breakpoints in communications and application processors in the system.

Parameters

access (optional)

The access type, in the form of access type-format.

Use the data parameter to set the format on IXP-based cards.

Range:

access type-format

access type—r, w, rw (read, write, read-write)

format— byte, word, dword, any

Default:: For x86-based cards— rw-byte
For IXP-based cards— rw-any

addr (optional)

The memory location in the form of segment–offset.

Range:

segment-offset

segment—h’00–h’ffff

offset—h’00–h’ffff

bc (optional)

The number of data bytes to display.

For IXP-based cards, bc represents the number of bytes of memory. The number of bytes of stack to be displayed is 255 – bc. For example, if bc=128, then 128 bytes of memory and 127 bytes of stack are displayed. If bc=0, then 0 bytes of memory and 255 bytes of stack are displayed. The exception to this rule is that 1 byte of stack is never displayed.

Range:

0 - 255

For x86-based cards, the maximum number of bytes is 96.

For IXP-based cards, the maximum number of bytes is 255.

ca (optional)

Condition “a” in the form of register–condition–integer.

The value register is the CPU internal register.

The value condition is the comparison condition (equal, not equal, greater than, less than, greater than or equal, less than or equal).

The value integer is the value for comparison.

Range:

register-condition-integer

register— sp, bp, ds, ss, es, cs, fl, ax, ah, al, bx, bh, bl, cx, ch, cl, dx, dh, dl, di, si, ip, fs, gs, esi, edi, ebp, esp, eip, efl, eax, ebx, ecx, edx, lr, pc, r1-r15

condition—eq, neq, gt, lt, gte, lte

integer—h’00–h’ffffffff

card (optional)

The card location, in the form of GPLID–Subsystem ID.

Range:

GPLID-Subsystem ID

GPLID—atmhc, deirhc, erthc, glshc, hipr2, ipghc, iplhc, ipsg, ipshc, mcphc, oamhc, pktgen, sccphc, siphc, ss7hc, utility

Subsystem ID— a, b, act, stb, all

The OAMHC GPL can be specified with any of the subsystem IDs.

For all other GPLs, only the all subsystem ID is valid.

cb (optional)

Condition b in the form of register–condition–integer.

The value register is the CPU internal register.

The value condition is the comparison condition (equal, not equal, greater than, less than, greater than or equal, less than or equal).

The value integer is the value for comparison.

Range:

register-condition-integer

register—sp, bp, ds, ss, es, cs, fl, ax, ah, al, bx, bh, bl, cx, ch, cl, dx, dh, dl, di, si, ip, fs, gs, esi, edi, ebp, esp, eip, efl, eax, ebx, ecx, edx, lr, pc, r0-r15

condition—eq, neq, gt, lt, gte, lte

integer—h’00–h’ffffffff

ctx (optional)

The bit-mapped microengine context mask.

Range:: 1 - 15

da (optional)

The dump address, in the form of segment–offset.

Range:

segment-offset

segment—h’00–h’ffff

offset—h’00–h’ffff

data (optional)

This parameter instructs a data breakpoint to qualify on a match of the data.

Note:

This parameter is valid only on IXP-based cards.

Range:

value-mask

value—0-0xFFFFFFFF

mask—0-0xFFFFFFFF

Default:: 0

dformat (optional)

Memory dump format (byte, doubleword, word).

Range:

byte
dword
word

Default:

byte

dpaddr (optional)

Memory dump address (physical offset).

Range:

h’00–h’ffffffff

dr (optional)

The data register indirect memory dump, in the form register-register-integer.

The register-register value is the CPU internal register.

The integer value is the offset value.

Range:

register-register-integer

register—sp, bp, ss, ds, es, cs, fl, ax, ah, al, bx, bh, bl, cx, ch, cl, dx, dh, dl, di, si, ip, fs, gs, esi, edi, ebp, esp, eip, efl, eax, ebx, ecx, edx

register—sp, bp, ds, ss, es, cs, fl, ax, ah, al, bx, bh, bl, cx, ch, cl, dx, dh, dl, di, si, ip, fs, gs, esi, edi, ebp, esp, eip, efl, eax, ebx, ecx, edx

integer— h’00–h’ffffffff

drarm (optional)

ARM register indirect memory dump.

Range:

ARM register-integer

arm register- r0-r15, sp, lr, pc

mask- 0-65535

The value ARM register is the CPU internal register.

The value integer is the offset value.

Default:

0

dur (optional)

Breakpoint duration.

Range:

temp
perm

Default:

temp

imt (optional)

IMT address of the card.

Range:: 0 - 254

ind (optional)

Indirection count.

Range:: 0 - 3
Default:: 0

loc (optional)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115

paddr (optional)

The physical offset of the memory address.

Range:: h’00–h’ffffffff

proc (optional)

Processor type.

Range:

appl: Application processor
com: Communication processor

Default:

appl

rep (optional)

Repetitions for this breakpoint.

Range:: 0 - 255
Default:: 0

type (optional)

Breakpoint type in the form of processor type-breakpoint type

Range:

processor type-breakpoint type

processor type—p186, p286, p486, arm, ixp

breakpoint type—code, codehw, codesw, data

Default:: For x86-based cards—p486-code
For IXP-based cards—arm-codesw

ueng (optional)

Microengine number. This parameter is valid only on IXP-based cards.

Note:

If this parameter is not specified for an IPX-based card, then the command is assumed to be intended for the ARM processor in the IXP chip.

Range:: 0 - 5

Example

ent-bp:loc=1204:paddr=h’27c3c:type=p486-data:access=rw-word

ent-bp:loc=1109:paddr=h’401000:type=arm-codesw:access=rw-any:ca=r7-eq-0

ent-bp:loc=1209:paddr=h’402000:type=arm-data:access=w-any:data=h’1111-h’ff

ent-bp:loc=1309:paddr=h’403000:type=ixp-codesw:ueng=2:ctx=1

ent-bp:card=hipr2-all:paddr=h’404000:type=arm-codehw:drarm=r3-0:bc=64

ent-bp:loc=1113:addr=h'03a-0001

Dependencies

All of the subsystem values can be specified with the OAMHC GPLID. The other GPLID values can be specified only with the all subsystem value.

2101 E2101 Cmd Rej: Card location is unequipped

Values of 1114, 1116, 1117, and 1118 cannot be specified for the loc parameter.

2212 E2212 Cmd Rej: Invalid card type for this command

The loc, imt, or card parameter must be specified.

2214 E2214 Cmd Rej: Missing parameter - CARD, LOC, or IMT

Only one of the loc, imt, and card parameters can be specified in the command.

2217 E2217 Cmd Rej: More than one of CARD, LOC, and IMT specified

The dr parameter and the da parameter cannot be specified together in the command.

2209 E2209 Cmd Rej: Both DR and DA parameters cannot be entered

The dur=perm parameter and the rep parameter cannot be specified together in the command.

2696 E2696 Cmd Rej: REP cannot be specified when DUR=PERM

The dur=perm parameter cannot be specified when the value of the processor type portion of the type parameter is p186 or p286.

2698 E2698 Cmd Rej: DUR=PERM cannot be specified with P186 or P286

When the da, dr, or drarm parameter is specified, the dpaddr parameter cannot be specified.

2695 E2695 Cmd Rej: DPADDR cannot be entered with DR/DRARM/DA

For the type parameter (which is in the form of processor type-breakpoint type), a breakpoint type of data cannot be specified in combination with a processor type of P186, P286, or IXP.

2699 E2699 Cmd Rej: DATA cannot be specified with TYPE = P186, P286, or IXP

When the paddr parameter and the bc parameter are specified, either the dpaddr or dr parameter must be specified in the command.

2703 E2703 Cmd Rej: Missing parameter - DPADDR or DR

The access parameter can be specified only when the type parameter value is p486-data or arm-data.

2700 E2700 Cmd Rej: ACCESS can only be specified with TYPE=P486-DATA or ARM-DATA

The bc parameter value cannot be greater than 96 for x86-based cards.

2219 E2219 Cmd Rej: Specified BC exceeds max allowed (96)

The ind parameter value cannot be greater than 3.

2697 E2697 Cmd Rej: IND cannot be greater than 3

The specified card must be in use.

2101 E2101 Cmd Rej: Card location is unequipped

For 80286 processors, registers for 80386 processors cannot be specified.

2720 E2720 Cmd Rej: 386/486 register cannot be specified

For 80286 processors, integer values for registers and conditions must be less than 65535.

2721 E2721 Cmd Rej: Integer value must be less than 65535

The ueng parameter is valid only on IXP-based cards (the value ixp is specified for the processor type portion of the type parameter).

4151 E4151 Cmd Rej: UENG parameter is invalid for this card

The cts parameter is valid only on IXP-based cards (the value ixp is specified for the processor type portion of the type parameter).

4146 E4146 Cmd Rej: CTX parameter is invalid for this card

The data parameter is valid only on IXP-based cards.

4148 E4148 Cmd Rej: DATA parameter is invalid for this card

The data parameter is valid only when the value is data for the breakpoint type portion of the type parameter.

4152 E4152 Cmd Rej: Invalid combination of TYPE and DATA parameters

The register values sp, lr, pc, and r0-r15 for the ca or cb parameters are valid only on IXP-based (ARM processor) cards.

4153 E4153 Cmd Rej: CA or CB register value is invalid for this card

The ca and cb parameters cannot be specified when the value ixp is specified for the processor type portion of the type parameter.

4150 E4150 Cmd Rej: CA/CB parameters are invalid for this processor

The drarm parameter can be specified only on IXP-based cards.

4156 E4156 Cmd Rej: DRARM parameter is invalid for this card

The drarm parameter can be specified only when the value arm is specified for the processor type portion of the type parameter.

4154 E4154 Cmd Rej: DRARM parameter is invalid for this processor

The dr parameter cannot be specified for IXP-based cards.

4155 E4155 Cmd Rej: DR parameter is invalid for this card

The data and codesw values for the breakpoint type portion of the type parameter cannot be specified when the value ixp is specified for the processor type portion of the type parameter.

4145 E4145 Cmd Rej: TYPE parameter value is invalid for this processor

The arm and ixp values for the processor type portion of the type parameter are valid only on IXP-based cards.

4159 E4159 Cmd Rej: TYPE parameter value is invalid for this card

The value any for the format portion of the access parameter can be specified only on IXP-based cards. The format value must be set to any on IXP-based cards.

4160 E4160 Cmd Rej: ACCESS parameter value is invalid for this card

When the value ixp is specified for the processor type portion of the type parameter, the ueng and cts parameters must be specified.

4147 E4147 Cmd Rej: Invalid combination of TYPE, UENG, and CTX parameters

The addr parameter can be specified only when the proc=com parameter is specified for DS0 cards with PROM-based COM processors (such as TSMs).

4158 E4158 Cmd Rej: ADDR parameter is invalid for this card

When the ca, cb, and dr parameters are used with 80186 and 80286 processors, the register values ip, fs, gs, esi, edi, ebp, esp, eip, efl, eax, ebx, ecx, and edx cannot be specified. These registers can be used only with 80486 processors. The integer values for these parameters when used with 80186 and 80286 processors must be less than h’ffff (65535).

N/A N/A

The data value for the breakpoint type portion of the type parameter cannot be specified with the values p186, p286, and ixp for the processor type portion of the type parameter.

4152 E4152 Cmd Rej: Invalid combination of TYPE and DATA parameters

The da parameter cannot be specified for IXP-based cards.

4157 E4157 Cmd Rej: DA parameter is invalid for this card

An ARM register value must be specified for an IXP-based card with an ARM processor.

4149 E4149 Cmd Rej: ARM register must be specified

The addr or paddr parameter must be specified in the command. Both parameters cannot be specified in the command.

2694 E2694 Cmd Rej: Invalid combination of ADDR and PADDR specified

Notes

The imt parameter allows this command to be entered for a card that has not been configured in the system.

Output

ent-bp:loc=1113:addr=h'03a-0001


    rlghncxa03w 04-08-22 21:14:41 EST EAGLE 33.0.0 
    SDS Response Code 22 from IMT Address H'00f6 - command complete. 

    rlghncxa03w 04-08-22 21:14:41 EST EAGLE 33.0.0 
    SDS Response from IMT Address H'000a - command complete. 
;

ent-bp:loc=6205:paddr=h'03a002


    rlghncxa03w 12-05-22 21:14:41 EST EAGLE 45.0.0
    SDS Response Code 22 from IMT Address H'00fd - command complete. 
;

Related Topics

ent-ee-flt

Use this command to enter Eagle Eyes Filter data in the Eagle Eyes Filter (EE FLT) table. The EE FLT entry consists of a Filter ID and Filter specific data. After the FLT ID is provisioned, it can be used in the dlt-ee-flt and chg-ee-card commands.

Parameters

type (mandatory)

Eagle Eyes Filter Type.

Range:: inc; exl

appl (mandatory)

Card Application Type

Range:: atm; ip; e1t1

ipprot (optional)

Filter based on IP sub-protocol

Range:: sctp; tcp; udp

ipsrc (optional)

Filter based on IP source address

Range:: 4 numbers separated by dots, with each number in the range of 0-255

ipdst (optional)

Filter based on IP destination address

Range:: 4 numbers separated by dots, with each number in the range of 0-255

ssport (optional)

Filter based on SCTP source port

Range:: 0-65535

sdport (optional)

Filter based on SCTP destination port.

Range:: 0-65535

stype (optional)

Filter based on SCTP chunk type

Range:: abrt; data; err; hbak; htbt; inak; init; sack

sctppld (optional)

Filter based on SCTP data payload identifier.

Range:: diam; m2pa; m3ua; sua; unspec

sctpstr (optional)

Filter based on SCTP data stream identifier

Range:: 0-65535

sscopsu (optional)

Filter based on SSCOP sub-protocol or SU type.

Range:: all; ctrl; data

mtp3si (optional)

Filter MTP3 user.

Range:: bicc; isup; sccp; snm; tup

port (optional)

Filter based on port.

Range:: a-b; a1-a31; b1-b31; all

sutype (optional)

Filter based on SU type.

Range:: allsu; lsu; msu

Example

ent-ee-flt:appl=ip:type=inc:ipprot=sctp:ssport=2048:stype=data:sctpstr=100

ent-ee-flt:appl=atm:type=exl:port=a:sscopsu=data:mtp3si=sccp

ent-ee-flt:appl=e1t1:type=exl:port=a1:sutype=msu:mtp3si=tup

Dependencies

If the appl=ip then ipprot, ipsrc or ipdst parameters must be specified.

2136 E2136 Cmd Rej: At least one optional parameter is required

If the ssport, sdport or stype parameters are specified, then the ipprot=sctp parameter must be specified.

2136 E2136 Cmd Rej: At least one optional parameter (ipprot or port) is required

At least one optional parameter (ipprot or port) must be specified.

2136 E2136 Cmd Rej: At least one optional parameter is required

If the sctppld parameter is specified, then the stype=data and ipprot=sctp parameters must be specified.

2379 E2379 Cmd Rej: Missing parameter

If the sctpstr parameter is specified, then the stype=data and ipprot=sctp parameters must be specified.

2379 E2379 Cmd Rej: Missing parameter

The Eagle Eyes Filter table cannot contain more than 200 entries.

2811 E2811 Cmd Rej: EE Filter table is full

The Eagle Eyes Filter table must be available.

2813 E2813 Cmd Rej: Unable to read EE Filter table

If the appl=ip parameter is specified, then the appl=atm and appl=e1t1 parameters must not be specified.

2155 E2155 Cmd Rej: Invalid parameter combination specified.

If the appl=atm parameter is specified, then the appl=ip and appl=e1t1 parameters must not be specified.

2155 E2155 Cmd Rej: Invalid parameter combination specified.

If the appl=e1t1 parameter is specified, then the appl=atm and appl=ip parameters must not be specified.

2155 E2155 Cmd Rej: Invalid parameter combination specified.

If the appl=atm parameter is specified, then the port parameter can only be either a, b or a1.

2155 E2155 Cmd Rej: Invalid parameter combination specified.

Notes

IP7 parameters:

ipprot, ipsrc, ipdst, ssport, sdport, style, sctppld, sctpstr

ATM parameters:

sscopsu, mtp3si, port

E1T1 parameters:

sutype, mtp3si, port

Output

ent-ee-flt:appl=atm:type=inc:port=a:sscopsu=data


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    EE FLT table is (1 of 200) 1% full
    ENT-EE-FLT: MASP A - COMPLTD 
;

dlt-ee-flt

rtrv-ee-flt

ent-trace

Use this debug command to trace MSUs sent to Service Module cards or to LIM cards running the SS7ANSI, CCS7ITU, VSCCP, ATMITU, ATMANSI, IPLIMI, SS7IPGW, IPGWI, or IPSG applications.

The EAGLE traps MSUs that meet the provisioned tracing criteria, and the MSU remains in the trapped state for the life span of that MSU. The life span varies depending on the type of MSU. For MTP-Routed or GTT MSUs, the life span lasts until the MSU travels out of the EAGLE or is discarded. For LNP MSUs, the life span lasts until the request is processed. The response is not part of the LNP MSU. Trapping a response requires the provisioning of another MSU trace.

This command uses different parameters depending on the card type sending the MSU as shown:

Service Module— error, gt, lrn, tn, ssp/sspa/sspi/sspn/sspn24/sspn16, dn, entityid, imei, and imsi
LIM card running ANSI applications— error, ssp/sspa, opc/opca, dpc/dpca, tlnpisuptype, and gt
LIM card running ITU applications— error, sspi/sspn/sspn24/sspn16, opci/opcn/opcn24/opcn16, dpci/dpcn/dpcn24/dpcn16, and gt

The lrn, tn, dn, entityid, imsi, imei, and error parameters are mutually exclusive.

The following parameters can be used once in a single MSU trace request with ONE of the mutually exclusive parameters specified above: opc, dpc, ilsn, si, gt, ssp, h0h1, cpc, or cic/ecic.

The cic/ecic parameters can be used only for ISUP traffic. The ecic parameter must be specified with the cic parameter.

For all cards supported by this command, the error parameter can be provisioned as the only optional parameter or in addition to any other optional parameter to trace any messages that fail verification or processing. If the error parameter not specified, the default value is error=no.

Caution:

If the system configuration approaches the maximum number of provisioned Service Module cards, then entering this command might cause an OAM to reset because of the amount of information that may be returned.

Parameters

card (mandatory)

The card location in the form of APPL CLASS-Subsystem ID.

Range:

APPL CLASS-Subsystem ID

APPL CLASS— atmansi, atmitu, ccs7itu, iplimi, ss7ansi, ss7ipgw, ipgwi, ipsg, vsccp

Subsystem ID— all

brief (optional)

This parameter specifies whether all information is provided for each MSU as it moves through the EAGLE.

Range:

no: All information, including data sections for the MSU, is displayed.
yes: The data sections for the MSU are not displayed.

cic (optional)

The beginning value for a CIC range.

Range:: 0 - 16383

cpc (optional)

ANSI destination point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm).

Synonym:

cpca

Range:

000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

When chg-sid:pctype=ansi is specified, ni = 000 is not valid.

When chg-sid:pctype=ansi is specified, nc = 000 is not valid if ni = 001–005.

When chg-sid:pctype=ansi is specified, nc = 000 is valid if ni = 006–255.

The point code 000-000-000 is not a valid point code.

cpci (optional)

ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).

Range:

0-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

zone—0–7

area—000–255

id—0-7

The point code 0-000-0 is not a valid point code.

cpcn (optional)

ITU national destination point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the chg-stpopts:npcfmti flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnngc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnngc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).

Range:

s-, 0-16383, aa-zz

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s-

nnnnn—0-16383

gc—aa-zz

m1-m2-m3-m4—0-14 for each member; values must sum to 14

cpcn24 (optional)

24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).

Range:

000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

msa—000–255

ssa—000–255

sp—000–255

cpcn16 (optional)

16-bit ITU national point code with subfields unit number-sub number area-main number area (un-sna-mna).

Range:: 000---127; Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).; un---000---127; sna---000---15; mna---000---31

dn (optional)

Directory Number. This parameter is used for the ANSI41 AIQ, ATINP, G-Flex, G-Port, INP, PPSMS, or V-Flex features.

The tn parameter is used as the directory number for LNP.

Range:: 5-15 digits
Valid digits are 0-9, a-f, A-F.

dpc (optional)

ANSI destination point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm)

Synonym:

dpca

Range:

000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

When chg-sid:pctype=ansi is specified, ni = 000 is not valid.

When chg-sid:pctype=ansi is specified, nc = 000 is not valid if ni = 001–005.

When chg-sid:pctype=ansi is specified, nc = 000 is valid if ni = 006–255.

The point code 000-000-000 is not a valid point code.

dpci (optional)

ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).

Range:

s-, 0-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s

zone—0-7

area—000-255

id—0-7

The point code 0-000-0 is not a valid point code.

dpcn (optional)

ITU national destination point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the chg-stpopts:npcfmti flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).

Range:

s-, 0-16383, aa-zz

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s-

nnnnn—0-16383

gc—aa-zz

m1-m2-m3-m4—0-14 for each member; values must sum to 14

dpcn24 (optional)

24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).

Range:

000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

msa—000–255

ssa—000–255

sp—000–255

dpcn16 (optional)

16-bit ITU national point code with subfields unit number-sub number area-main number area (un-sna-mna).

Range:: 000---127; Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).; un---000---127; sna---000---15; mna---000---31

ecic (optional)

The end value for a CIC range.

Range:: 0 - 16383

entityid (optional)

The entity ID.

Range:: 1-15 digits
Valid digits are 0-9, a-f, A-F

error (optional)

This parameter specifies whether to perform a trace on any message verification error and message processing error

Range:

yes
no

Default:

no

gt (optional)

Global title. The CdPA global title digits.

Range:: 1-21 digits
Valid digits are 0-9, a-f, A-F

h0h1 (optional)

A combination of values contained in some MSUs. The h0 value is the code for a message group, and the h1 value is the code for a message within that group.

Range:: 0 - 255

ilsn (optional)

The incoming linkset name.

Range:: ayyyyyyyyy
1 alphabetic character followed by up to 9 alphanumeric characters.

imei (optional)

The International Equipment Identifier.

Range:: Exactly 14 digits; valid digits are 0-9, a-f, A-F

imsi (optional)

The International Mobile Station Identifier.

Range:: 5-15 digits
Valid digits are 0-9, a-f, A-F

loc (optional)

The card location of the card as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

lrn (optional)

The local routing number.

Range:: Exactly 14 digits: Valid digits are 0-9.

mode (optional)

The type of output displayed.

Range:

default: The default value of this parameter.
detail: Detailed information is displayed when an MSU matches the request.
debug: Complete information is displayed when an MSU matches the request.

opc (optional)

ANSI point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm). The prefix subfield indicates a private point code (prefix-ni-nc-ncm).

Synonym:: opca

Range:

000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

When chg-sid:pctype=ansi is specified, ni = 000 is not valid.

When chg-sid:pctype=ansi is specified, nc = 000 is not valid if ni = 001–005.

When chg-sid:pctype=ansi is specified, nc = 000 is valid if ni = 006–255.

The point code 000-000-000 is not a valid point code.

opci (optional)

ITU international origination point code with subfields zone-area-id. The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-zone-area-id).

Range:

s-, p-, ps-, 0-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s-, p-, ps

zone—0-7

area—000-255

id—0-7

The point code 0-000-0 is not a valid point code.

opcn (optional)

ITU national destination point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the chg-stpopts:npcfmti flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnngc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnngc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).

Range:

s-, 0-16383, aa-zz

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s-

nnnnn—0-16383

gc—aa-zz

m1-m2-m3-m4—0-14 for each member; values must sum to 14

opcn24 (optional)

24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).

Range:

000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

msa—000–255

ssa—000–255

sp—000–255

opcn16 (optional)

16-bit ITU national point code with subfields unit number-sub number area-main number area (un-sna-mna).

Range:: 000---127; Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).; un---000--127; sna--000---15; mna---000--31

rep (optional)

The number of MSUs to trap.

Range:: 0 - 255

service (optional)

The service offered by the EAGLE.

Range:

gflex
gport
inpmr
inpq
smsmr
mnpsms
eir
idpr
idps
tif
tif2
tif3
tobr
aiq

si (optional)

Service indicator.

Range:: 0 - 15

sls (optional)

Signaling link selector.

Range:: 0 - 255

ssp (optional)

ANSI destination point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm).

Synonym: sspa

Range:

000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

When chg-sid:pctype=ansi is specified, ni = 000 is not valid.

When chg-sid:pctype=ansi is specified, nc = 000 is not valid if ni = 001–005.

When chg-sid:pctype=ansi is specified, nc = 000 is valid if ni = 006–255.

The point code 000-000-000 is not a valid point code.

sspi (optional)

ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).

Range:

s-, 0-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s

zone—0-7

area—000-255

id—0-7

The point code 0-000-0 is not a valid point code.

sspn (optional)

ITU national destination point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the chg-stpopts:npcfmti flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnngc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnngc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).

Range:

s-, 0-16383, aa-zz

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s-

nnnnn—0-16383

gc—aa-zz

m1-m2-m3-m4—0-14 for each member; values must sum to 14

sspn24 (optional)

24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).

Range:

000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

msa—000–255

ssa—000–255

sp—000–255

sspn16 (optional)

16-bit ITU national point code with subfields unit number-sub number area-main number area (un-sna-mna).

Range:: 000---127; Specify a valid value for each subfield of the point code, and the separate the subfields with a dash (-).; un---000---127; sna---000---15; mna---000---31

tlnpisuptype (optional)

The ISUP message type.

Range:: 0 - 255

tn (optional)

The directory number.

Range:: Exactly 10 digits. Valid digits are 0-9

Example

ent-trace:opc=1-1-1:card=SS7ANSI-ALL:rep=2

ent-trace:tlnpisuptype=01:card=SS7ANSI-ALL

ent-trace:dn=12345:card=VSCCP-ALL

ent-trace:imsi=c122d:card=VSCCP-ALL

ent-trace:card=ccs7itu-all:dpc=2-7-5:error=no

ent-trace:card=vsccp-all:error=yes

ent-trace:card=ccs7itu-all:sspn24=10-11-12:opcn24=10-10-10:dpcn24=10-101-11

ent-trace:imei=123456789101234:card=VSCCP-ALL

ent-trace:entityid=c123:card=VSCCP-ALL

ent-trace:loc=1305:si=5:brief=yes

ent-trace:dn=98912345:loc=1105

ent-trace:card=ccs7itu-all:sspn16=121-10-12:opcn16=121-10-13:dpcn16=121-10-14

Dependencies

The card parameter or the loc parameter must be specified.

2214 E2214 Cmd Rej: Missing parameter - CARD, LOC, or IMT

At least one optional parameter must be specified. The error parameter can be specified as the only optional parameter or with any of the other optional parameters in the command.

2136 E2136 Cmd Rej: At least one optional parameter is required

The gt, entityid, dn, imei, and imsi parameters cannot have a value of none.

3502 E3502 Cmd Rej: The NONE value is not allowed in this case

A valid value must be specified for the card parameter.

2212 E2212 Cmd Rej: Invalid card type for this command

The only qualifier allowed for the card parameter is all.

2208 E2208 Cmd Rej: ALL only qualifier allowed with given card type

The gt, entityid, dn, imei, imsi, lrn, and tn parameters are invalid for LIM cards running the SS7ANSI, ATMANSI, or SS7IPGW applications.

3425 E3425 Cmd Rej: Invalid parameter for SS7ANSI, ATMANSI, or SS7IPGW

The opci/opcn/opcn24/opcn16, dpci/dpcn/dpcn24/dpcn16, and sspi/sspn/sspn24/sspn16 ITU point code parameters are invalid for LIM cards running the SS7ANSI, ATMANSI, or SS7IPGW applications.

3427 E3427 Cmd Rej: ITU PC parameters are invalid for ANSI cards

The gt, entityid, dn, imei, imsi, lrn, tn, and tlnpisuptype parameters are invalid for LIM cards running the ATMITU or IPLIMI applications.

3428 E3428 Cmd Rej: Invalid parameter for CCS7ITU or IPLIMI

The opc/opca, dpc/dpca, and ssp/sspa ANSI point code parameters are invalid for LIM cards running the IPLIMI application.

3426 E3426 Cmd Rej: ANSI PC parameters are invalid for ITU cards

The opc, dpc, and tlnpisuptype parameters cannot be specified for Service Module cards.

3429 E3429 Cmd Rej: Invalid parameter for VSCCP

The G-Flex feature or the Equipment Identity Register feature must be turned on before the imsi parameter can be specified.

4192 E4192 Cmd Rej: GFLEX or EIR feature must be ON

If the ITUDUPPC feature is turned on, the ITU national point code must be specified as a full point code.

3921 E3921 Cmd Rej: ITU National Point Code must be full point code

The EIR feature must be turned on before the imei parameter can be specified.

3699 E3699 Cmd Rej: EIR feature must be ON

The AINPQ, G-Flex, G-Port, IDP Relay, INP, PPSMS, or V-Flex feature must be turned on or the ANSI41 AIQ or ATINP feature must be enabled before the dn parameter can be specified.

The G-Flex, G-Port, INP, or V-Flex feature must be turned on or the ATINP, IDP Relay or any TIF feature must be enabled before the entityid parameter can be specified.

3342 E3342 Cmd Rej: GFLEX/INP/AINPQ/GPORT/PPSMS/VFLEX OFF or ATINP/AIQ not enbld

The loc and card parameters are mutually exclusive.

Only one of the lrn, tn, dn, entityid, imsi, imei, or error parameters can be specified in a single MSU trace request.

2155 E2155 Cmd Rej: Invalid parameter combination specified

A maximum of 10 traces can be entered in the system at a time.

4980 E4980 Cmd Rej: Maximum number of traces already entered

Values 1113 - 1118 cannot be specified for the loc parameter.

2025 E2025 Cmd Rej: Invalid card location

The J7 Support feature must be enabled before the sspn16/opcn16/dpcn16 parameters can be specified.

2691 E2691 Cmd Rej: J7 Support Feature must be enabled.

Output

This example shows the output for an MTP trace:

ent-trace:loc=1101:dpc=7-1-0


    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e1:  Card=1101   RX - Link B0
    Trace Condition:
    LOC=           1101
    DPC=           007-001-000

    MSU info:
    TOTAL MSU SIZE=  12 Bytes
    MSU DATA SIZE =  4 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  85 00 01 07 01 65 01 16

    DATA: 00 00 09 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e1:  Card=1101   Use RTE:   007-001-000:H'0001
    Trace Condition:
    LOC=          1101
    DPC=          007-001-000

    MSU info:
    TOTAL MSU SIZE=  12 Bytes
    MSU DATA SIZE =  4 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  85 00 01 07 01 65 01 16

    DATA: 00 00 09 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0    
    MSU TRACE H'00e1:  Card=1101   Sending to 1103:B1
    Trace Condition:
    LOC=          1101
    DPC=          007-001-000

    MSU info:
    TOTAL MSU SIZE=  12 Bytes
    MSU DATA SIZE =  4 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  85 00 01 07 01 65 01 0b

    DATA: 00 00 09 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e1:  Card=1103   MSU Received from 1101
    Trace Condition:
    LOC=          1101
    DPC=          007-001-000

    MSU info:
    TOTAL MSU SIZE=  12 Bytes
    MSU DATA SIZE =  4 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  85 00 01 07 01 65 01 0b

    DATA: 00 00 09 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e1:  Card=1103   MSU sent to L2 - B1
    Trace Condition:
    LOC=          1101
    DPC=          007-001-000

    MSU info:
    TOTAL MSU SIZE=  12 Bytes
    MSU DATA SIZE =  4 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  85 00 01 07 01 65 01 0b

    DATA: 00 00 09 00
    TRACE OUTPUT COMPLETE. 
;

This example shows the output for an SCCP trace:

ent-trace:loc=1101:gt=9194605500


    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1101   RX - Link B0
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  90 Bytes
    MSU DATA SIZE =  82 Bytes
   
          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 01 01 65 01 02

    SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1101   TVG: Sending to SCCP 1107
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  90 Bytes
    MSU DATA SIZE =  82 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 01 01 65 01 02

    SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1107   MSU Received from 1101
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  90 Bytes
    MSU DATA SIZE =  82 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 01 01 65 01 02

    SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1107   SCCP: Before SS7 Trans Encod
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  97 Bytes
    MSU DATA SIZE =  89 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 01 01 65 01 02

    SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02 
          08 01 65 01 00 04
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1107   SCCP: After SS7 Trans Encode
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  97 Bytes
    MSU DATA SIZE =  89 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 07 00 01 01 02

    SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
          08 01 65 01 00 04
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1107   Use RTE 007-001-000:H'0009
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  97 Bytes
    MSU DATA SIZE =  89 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 07 00 01 01 02

    SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
          08 01 65 01 00 04
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1107   Sending to 1103:B1
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  97 Bytes
    MSU DATA SIZE =  89 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 07 00 01 01 01

    SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
          08 01 65 01 00 04
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'0000:  Card=1103   MSU Received from 1107
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  97 Bytes
    MSU DATA SIZE =  89 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 07 00 01 01 01

    SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
          08 01 65 01 00 04
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'0000:  Card=1103   MSU sent to L2 - B1
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  90 Bytes
    MSU DATA SIZE =  82 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 07 00 01 01 01

    SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
          04 05 06
 

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
    TRACE OUTPUT COMPLETE. 
;

This example shows the output for a trace when truncated output is requested. Only the filters that are specified in the command are displayed.

ent-trace:loc=1305:si=0:hoh1=20:sls=255:cpc=001-002-003:mode=debug:brief=yes


    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0 
;
    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0
    MSU TRACE H'0081:  Card=1305
    Trace ID 1 Condition:
    LOC=          1305
    SI=           0
    H0H1=         20
    SLS=          255
    CPC=          001-002-003
    MODE=         DEBUG

    Info: RX - Link A0

    TRACE OUTPUT COMPLETE. 
;

    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0
    MSU TRACE H'0081:  Card=1305
    Trace ID 1 Condition:
    LOC=          1305
    SI=           0
    H0H1=         20
    SLS=          255
    CPC=          001-002-003
    MODE=         DEBUG

    Info: TIF Stop Action: OK 

    TRACE OUTPUT COMPLETE. 
;

    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0
    MSU TRACE H'0081:  Card=1305
    Trace ID 1 Condition:
    LOC=          1305
    SI=           0
    H0H1=         20
    SLS=          255
    CPC=          001-002-003
    MODE=         DEBUG

    Info: TVG: Sending to SCCP 1317 

    TRACE OUTPUT COMPLETE. 
;

    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0
    MSU TRACE H'0081:  Card=1317
    Trace ID 1 Condition:
    LOC=          1305
    SI=           0
    H0H1=         20
    SLS=          255
    CPC=          001-002-003
    MODE=         DEBUG

    Info: SCCP: MSU RX from 1305

    TRACE OUTPUT COMPLETE. 
; 

    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0
    MSU TRACE H'0081:  Card=1317
    Trace ID 1 Condition:
    LOC=          1305
    SI=           0
    H0H1=         20
    SLS=          255
    CPC=          001-002-003
    MODE=         DEBUG
    
    Info: TIF Process Msg: Ruleset TIF1

    TRACE OUTPUT COMPLETE. 
;
    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0
    MSU TRACE H'0081:  Card=1317
    Trace ID 1 Condition:
    LOC=          1305
    SI=           0
    H0H1=         20
    SLS=          255
    CPC=          001-002-003
    MODE=         DEBUG

    Info: TIF: No Error CdPN:1111111119703819111100

    TRACE OUTPUT COMPLETE. 
;

    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0
    MSU TRACE H'0081:  Card=1305
    Trace ID 1 Condition:
    LOC=          1305
    SI=           0
    H0H1=         20
    SLS=          255
    CPC=          001-002-003
    MODE=         DEBUG

    Info: Use RTE (16) DPCa:   023-172-011, OPCa:   013-159-005

    TRACE OUTPUT COMPLETE. 
;

    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0
    MSU TRACE H'0081:  Card=1305
    Trace ID 1 Condition:
    LOC=          1305
    SI=           0
    H0H1=         20
    SLS=          255
    CPC=          001-002-003
    MODE=         DEBUG

    Info: Sending to 2311:B3

    TRACE OUTPUT COMPLETE. 
;

    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0
    MSU TRACE H'0081:  Card=2311
    Trace ID 1 Condition:
    LOC=          1305
    SI=           0
    H0H1=         20
    SLS=          255
    CPC=          001-002-003
    MODE=         DEBUG

    Info: MSU Received from 1305
 
    TRACE OUTPUT COMPLETE. 
;

    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0
    MSU TRACE H'0081:  Card=2311
    Trace ID 1 Condition:
    LOC=          1305
    SI=           0
    H0H1=         20
    SLS=          255
    CPC=          001-002-003
    MODE=         DEBUG

    Info: MSU sent to L2 - B3: DPCa=   023-172-011, OPCa=   013-159-005

    TRACE OUTPUT COMPLETE. 
;

    tklc1071501 08-09-22 10:49:00 EST  EAGLE5 39.2.0
    MSU TRACE H'0081:  Card=2311
    Trace ID 1 Condition:
    LOC=          1305
    SI=           0
    H0H1=         20
    SLS=          255
    CPC=          001-002-003
    MODE=         DEBUG

    Info: Transmitted and ACK'd on B3

    TRACE OUTPUT COMPLETE. 
;

This example shows the output for an MTP trace:

ent-trace:loc=1101:dpcn16=7-1-0


    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e1:  Card=1101   RX - Link B0
    Trace Condition:
    LOC=           1101
    DPC=           007-001-000

    MSU info:
    TOTAL MSU SIZE=  12 Bytes
    MSU DATA SIZE =  4 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  85 00 01 07 01 65 01 16

    DATA: 00 00 09 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e1:  Card=1101   Use RTE:   007-001-000:H'0001
    Trace Condition:
    LOC=          1101
    DPC=          007-001-000

    MSU info:
    TOTAL MSU SIZE=  12 Bytes
    MSU DATA SIZE =  4 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  85 00 01 07 01 65 01 16

    DATA: 00 00 09 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0    
    MSU TRACE H'00e1:  Card=1101   Sending to 1103:B1
    Trace Condition:
    LOC=          1101
    DPC=          007-001-000

    MSU info:
    TOTAL MSU SIZE=  12 Bytes
    MSU DATA SIZE =  4 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  85 00 01 07 01 65 01 0b

    DATA: 00 00 09 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e1:  Card=1103   MSU Received from 1101
    Trace Condition:
    LOC=          1101
    DPC=          007-001-000

    MSU info:
    TOTAL MSU SIZE=  12 Bytes
    MSU DATA SIZE =  4 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  85 00 01 07 01 65 01 0b

    DATA: 00 00 09 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e1:  Card=1103   MSU sent to L2 - B1
    Trace Condition:
    LOC=          1101
    DPC=          007-001-000

    MSU info:
    TOTAL MSU SIZE=  12 Bytes
    MSU DATA SIZE =  4 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  85 00 01 07 01 65 01 0b

    DATA: 00 00 09 00
    TRACE OUTPUT COMPLETE. 
;

This example shows the output for an SCCP trace:

ent-trace:loc=1101:gt=9194605500


    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1101   RX - Link B0
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  90 Bytes
    MSU DATA SIZE =  82 Bytes
   
          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 01 01 65 01 02

    SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1101   TVG: Sending to SCCP 1107
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  90 Bytes
    MSU DATA SIZE =  82 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 01 01 65 01 02

    SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1107   MSU Received from 1101
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  90 Bytes
    MSU DATA SIZE =  82 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 01 01 65 01 02

    SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1107   SCCP: Before SS7 Trans Encod
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  97 Bytes
    MSU DATA SIZE =  89 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 01 01 65 01 02

    SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02 
          08 01 65 01 00 04
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1107   SCCP: After SS7 Trans Encode
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  97 Bytes
    MSU DATA SIZE =  89 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 07 00 01 01 02

    SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
          08 01 65 01 00 04
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1107   Use RTE 007-001-000:H'0009
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  97 Bytes
    MSU DATA SIZE =  89 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 07 00 01 01 02

    SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
          08 01 65 01 00 04
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'00e2:  Card=1107   Sending to 1103:B1
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  97 Bytes
    MSU DATA SIZE =  89 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 07 00 01 01 01

    SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
          08 01 65 01 00 04
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'0000:  Card=1103   MSU Received from 1107
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  97 Bytes
    MSU DATA SIZE =  89 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 07 00 01 01 01

    SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
          04 05 06

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
          08 01 65 01 00 04
    TRACE OUTPUT COMPLETE. 
;

    stdcfg1b 07-08-10 15:51:33 EST  EAGLE 37.5.0
    MSU TRACE H'0000:  Card=1103   MSU sent to L2 - B1
    Trace Condition:
    LOC=          1101
    GT=           9194605500

    MSU info:
    TOTAL MSU SIZE=  90 Bytes
    MSU DATA SIZE =  82 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9
    MTP:  83 00 01 07 00 01 01 01

    SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
          04 05 06
 

    TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
          f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
          0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
    TRACE OUTPUT COMPLETE. 
;

This example shows the output to display the selected highest priority component in a TCAP message:

ent-trace:loc=1103:si=3:mode=debug

tekelecstp 17-03-22 11:30:07 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: SCCP: service selector not found

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 3f 78 0c 0c

    SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:07 MST  EAGLE 46.5.0.0.0-70.26.0
    1660.0309    SYSTEM                  Node is no longer isolated
;
    tekelecstp 17-03-22 11:30:07 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: TOBR:Msg=Begin Opcode=2,22,8 ACN(hex)= 0

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 3f 78 0c 0c

    SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:08 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: GTT Mode=FD-FG,GTIi=2/2,TT11/242,SS10/242,NP-/-,NAI-/-,SelID=NONE

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 3f 78 0c 0c

    SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:08 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: LS:     ls661

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 3f 78 0c 0c

    SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:09 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: dGT=22222210,gGT=9876543210,gPC=7-080-1,
    OPCi=6-006-1,DPCi=7-007-7

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 3f 78 0c 0c

    SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:10 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: Opcode 8 from component#3 selected for translation

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 3f 78 0c 0c

    SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:10 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: Opcode 2 from component#1 selected for translation

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 3f 78 0c 0c

    SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:11 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: SET=FD-cd1-amituopcd-cg1-ZITUOPCD

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 3f 78 0c 0c

    SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:11 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: xlatPCi=6-008-1,SS=0,RI=0,GTMODID=-,CGPCACT=DFLT,ACTSN=-

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 3f 78 0c 0c

    SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:12 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: SCCP - Before Encode :old, GTT perfd

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 3f 78 0c 0c

    SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:12 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: After Encd:OPCi=7-007-7,DPCi:6-008-1,CgPC=7-080-1

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 41 f0 0f 0e

    SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:13 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: route_message_hp:DPCi=6-008-1,OPC=7-007-7>route_msg_on_rtidx

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 41 f0 0f 0e

    SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:13 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: Use RTE (5) DPCi:   6-008-1, OPCi:   7-007-7

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 41 f0 0f 0e

    SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:14 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: Rotated SLS = H'0000

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 41 f0 0f 0e

    SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:14 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1103
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: Sending to 1102:A1

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 41 f0 0f 0e

    SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:15 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1102
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: MSU Received from 1103

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 41 f0 0f 0e

    SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-22 11:30:15 MST  EAGLE 46.5.0.0.0-70.26.0
    MSU TRACE H'0021:  Card=1102
    Trace ID 1 Condition: (brief=Y, MSU size=145)
    LOC=          1103
    SI=           3
    MODE=         debug

    Info: MSU sent to L2: A1: DPCi=6-008-1,OPCi=7-007-7,NI=0

    MSU info:
    TOTAL MSU SIZE=  145 Bytes
    MSU DATA SIZE =  140 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  03 41 f0 0f 0e

    SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
          f2 89 67 45 23 01

    TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
          12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
          49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
          80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
          10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
          01 00 02 01 08 30 07 80 05 89 67 45 23 01

    TRACE OUTPUT COMPLETE.
;

This example shows the output for mode=debug:

ent-trace:loc=1107:si=12:mode=debug

tekelecstp 17-03-03 10:23:27 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: RX:SLK A0,DPCi=1-001-3,APCi=1-001-2,TSPCi=1-001-1,SAPC =

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 c2

    DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:27 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: SS7_HMDC:4thisPC=N,TRUE_PCi=1-001-3 =>sccp=No

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 c2

    DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:27 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: HMDC MTP-routes MSU: call route_message_hp

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 c2

    DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:28 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: route_message_hp:DPCi=1-001-3,OPC=1-001-1>route_msg_on_rtidx

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 c2

    DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:28 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: Use RTE (5) DPCi:   1-001-3, OPCi:   1-001-1

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 c2

    DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:29 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: Rotated SLS = H'000c

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 c2

    DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:29 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: Sending to 1108:A0

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 c2

    DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:29 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1108
    Trace ID 1 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: MSU Received from 1107

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 c2

    DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;

This example shows the output for mode=debug and brief=yes:

ent-trace:loc=1107:si=12:mode=debug:brief=yes

tekelecstp 17-03-03 10:23:40 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=Y, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: RX:SLK A0,DPCi=1-001-3,APCi=1-001-2,TSPCi=1-001-1,SAPC =

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:40 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=Y, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: SS7_HMDC:4thisPC=N,TRUE_PCi=1-001-3 =>sccp=No

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:40 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=Y, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: HMDC MTP-routes MSU: call route_message_hp

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:40 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=Y, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: route_message_hp:DPCi=1-001-3,OPC=1-001-1>route_msg_on_rtidx

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:41 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=Y, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: Use RTE (5) DPCi:   1-001-3, OPCi:   1-001-1

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:41 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=Y, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: Rotated SLS = H'0000

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:41 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1107
    Trace ID 1 Condition: (brief=Y, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: Sending to 1108:A0

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:41 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c1:  Card=1108
    Trace ID 1 Condition: (brief=Y, MSU size=101)
    LOC=          1107
    SI=           12
    MODE=         debug

    Info: MSU Received from 1107

    TRACE OUTPUT COMPLETE.
;

This example shows the output for when the mode is not defined:

ent-trace:loc=1107:si=12

tekelecstp 17-03-03 10:23:49 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c2:  Card=1107
    Trace ID 2 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12

    Info: RX:SLK A0,DPCi=1-001-3,APCi=1-001-2,TSPCi=1-001-1,SAPC =

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 52

    DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:49 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c2:  Card=1107
    Trace ID 2 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12

    Info: SS7_HMDC:4thisPC=N,TRUE_PCi=1-001-3 =>sccp=No

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 52

    DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:50 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c2:  Card=1107
    Trace ID 2 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12

    Info: Use RTE (5) DPCi:   1-001-3, OPCi:   1-001-1

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 52

    DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:51 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c2:  Card=1107
    Trace ID 2 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12

    Info: Sending to 1107:A0

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 52

    DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:51 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c2:  Card=1107
    Trace ID 2 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12

    Info: MSU Received from 1107

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 52

    DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;
    tekelecstp 17-03-03 10:23:51 EST  EAGLE 46.5.0.0.0-70.21.0
    MSU TRACE H'00c2:  Card=1107
    Trace ID 2 Condition: (brief=N, MSU size=101)
    LOC=          1107
    SI=           12

    Info: MSU sent to L2: A0: DPCi=1-001-3,OPCi=1-001-1,NI=0

    MSU info:
    TOTAL MSU SIZE=  101 Bytes
    MSU DATA SIZE =  096 Bytes

          0  1  2  3  4  5  6  7  8  9  0  1  2  3  4  5  6  7  8  9

    MTP:  0c 0b 48 02 52

    DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
          00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
          00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
          00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
          00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e

    TRACE OUTPUT COMPLETE.
;

None.

rept-stat-ee

Use this command to generate the status report of Eagle Eyes on network cards.

Parameters

loc (optional)

Eagle Eyes Card location.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

Example

rept-stat-ee

rept-stat-ee:loc=1102

Dependencies

The card location specified in the 'loc' parameter must be configured to use Eagle Eyes.

2984 E2984 Cmd Rej: Eagle Eyes not configured on the card

The shelf and card must be equipped.

2144 E2144 Cmd Rej: Location invalid for hardware configuration

The specified card location must not be a reserved card location.

2376 E2376 Cmd Rej: Specified LOC is invalid

Notes

This command can be canceled using the F9 function key or the canc-cmd command. See canc-cmd for more information

Output

This example generates the Eagle Eyes status report for the specified Network Card.

rept-stat-ee:loc=1101


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    LOC        STATE
    ----------------
    1101       ACTIVE


    Command Completed.

This example generates the Eagle Eyes status report for all the EE configured Network Cards.

rept-stat-ee


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    LOC        STATE
    ----------------
    1101       ACTIVE
    1103       INACTIVE
    Command Completed.

Related Topics

rept-stat-gedti

Use this command to generate a report of the GEDTI Hub's status.

Parameters

loc (optional)

GEDTI Hub Card location.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

Example

rept-stat-gedti

rept-stat-gedti:loc=1111

Dependencies

The value specified for the loc parameter must correspond to the location of an IPSM card which is configured as a GEDTI Hub.

2025 E2025 Cmd Rej: Invalid card location

Notes

This command can be canceled using the F9 function key or the canc-cmd command. See canc-cmd for more information.

Output

This example generates the report of all the IPSM cards configured as GEDTI Hubs.

rept-stat-gedti


    tekelecstp 08-01-29 10:41:52 EST  EAGLE 46.0.0

    LOC       PORT      STATE
    -------------------------------------------------------------------------
    1101      4567      ACTIVE

    SID   SOCK FD   APPL CARD   APPL SUBSYS   APPL ID   PC STATE   APPL STATE
    -------------------------------------------------------------------------
    0    -1         0           0             0         0          0
    1    -1         0           0             0         0          0
    2    -1         0           0             0         0          0
    3    -1         0           0             0         0          0
    4    -1         0           0             0         0          0
    5    -1         0           0             0         0          0
    6    -1         0           0             0         0          0
    7    -1         0           0             0         0          0

    LOC       PORT      STATE
    -------------------------------------------------------------------------
    1112      4568      INACTIVE

    SID   SOCK FD   APPL CARD   APPL SUBSYS   APPL ID   PC STATE   APPL STATE
    -------------------------------------------------------------------------
    0     0          0          0             0         0          0

    Command Completed.

This example generates the report of the specified IPSM card configured as a GEDTI Hub.

rept-stat-gedti:loc=1101


tekelecstp 08-01-29 10:41:54 EST  EAGLE 46.0.0


    LOC       PORT      STATE
    -------------------------------------------------------------------------
    1101      4567      ACTIVE

    SID   SOCK FD   APPL CARD   APPL SUBSYS   APPL ID   PC STATE   APPL STATE
    -------------------------------------------------------------------------
    0    -1         0           0             0         0          0
    1    -1         0           0             0         0          0
    2    -1         0           0             0         0          0
    3    -1         0           0             0         0          0
    4    -1         0           0             0         0          0
    5    -1         0           0             0         0          0
    6    -1         0           0             0         0          0
    7    -1         0           0             0         0          0
    Command Completed.

Related Topics

rtrv-ee-card

Use this command to display Eagle Eyes Card Configuration data from the Eagle Eyes Card (EE CARD) table. The EE CARD entry consists of a Card Loc and Eagle Eyes Card specific data.

Parameters

loc (optional)

Eagle Eyes Card location.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

Example

rtrv-ee-card

rtrv-ee-card:loc=1102

Dependencies

The EE CARD table must be available.

2867 E2867 Cmd Rej: Unable to read EE Card table

The card location specified in the 'loc' parameter must be configured to use Eagle Eyes.

2984 E2984 Cmd Rej: Eagle Eyes not configured on the card

The Eagle Eyes Filter table must be available.

2813 E2813 Cmd Rej: Unable to read EE FLT table

Notes

None.

Output

This example displays the Eagle Eyes parameters for all the EE configured network cards.

rtrv-ee-card


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    LOC  THR   SECLIM  PKTLIM   KBLIM     
    -----------------------------------
    1101 10000 5644800 10000000 4000000
    1201 1000  464400  NONE     2000000


    EE CARD table is (2 of 254) 1% full

    RTRV-EE-CARD: MASP A - COMPLTD 
;

This example displays the Eagle Eyes parameters for the specified EE configured network card.

rtrv-ee-card:loc=1201


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    
    EE OAM Card Configuration
    -------------------------------------------
    LOC  THR   SECLIM   PKTLIM   KBLIM   PORT
    -------------------------------------------

    1201 1000  2000     2000     3000    -

    ATM FILTERS
    -----------------------------
    ID  TYPE PORT SSCOPSU MTP3SI
    -----------------------------
    71   INC a    ctrl    -
    13   INC a     -      -
    5    EXC b     -      -

    EE CARD table is (2 of 254) 1% full

    RTRV-EE-CARD: MASP A - COMPLTD 
;

Legend

LOC--- Card location as stenciled on the shelf of the system.
THR--- The sending rate of the Eagle Eyes throttle task in IMT packets per second.
SECLIM--- The limit on the amount of time to perform the trace, in seconds.
PKTLIM--- The limit on the number of Ethernet frames to send.
KBLIM--- The file size limit of the capture file created, in kilobytes.
PORT--- Port being filtered.
ID--- Eagle Eyes Filter ID.
TYPE--- Eagle Eyes Filter Type.
SSCOPSU--- SSCOP sub-protocol or SU type filter.
MTP3SI--- MTP3 user filter.

chg-ee-card

dact-ee

rept-stat-ee

rtrv-ee-flt

Use this command to retrieve Eagle Eyes Filter data from the Eagle Eyes Filter (EE FLT) table. The EE-FLT entry consists of a Filter ID and Filter specific data. It can be used to obtain the Filter ID of the filter to be associated to a card using the CHG-EE-CARD command.

Parameters

appl (optional)

Card Application Type

Range:: ATM; IP; E1T1

fltid (optional)

Eagle Eyes Filter ID

Range:: 1-200

Example

rtrv-ee-flt:appl=ip

rtrv-ee-flt:fltid=16

Dependencies

The Eagle Eyes Filter table must be available.

2813 E2813 Cmd Rej: Unable to read EE Filter table

The specified Filter ID must exist in the EE FLT table.

2827 E2827 Cmd Rej: Filter not present

The Filter ID and APPL are mutually exclusive parameters.

2155 E2155 Cmd Rej: Invalid parameter combination specified.

Notes

None.

Output

This example displays the Filter parameters for the specified Filter ID.

rtrv-ee-flt:fltid=85


tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    EE OAM Filter Configuration
    IP FILTERS
    --------------------------------------------------------------------------
    ID  TYPE IP   IP              IP              SCTP  SCTP  SCTP  SCTP  SCTP
             PROT SRC             DST             SRC   DST   TYPE  DATA  DATA
                  ADDR            ADDR            PORT  PORT        PLD   STR
    --------------------------------------------------------------------------
    85  INC sctp  -               -               -     -     data  sua   -
    EE Filter table is (83 of 200) 42% full.

;
Command Executed

This example displays the Filter parameters for the ATM Application Type.

rtrv-ee-flt:appl=atm


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    EE OAM Filter Configuration
    ATM FILTERS
    -----------------------------
    ID  TYPE PORT SSCOPSU MTP3SI
    -----------------------------
    5    EXC b     -      -
    13   INC a     -      -
    67   INC a     -      -
    68   INC a1    -      -
    71   INC a    ctrl    -
    77   INC all   -      -

    EE Filter table is (83 of 200) 42% full.
;
Command Executed

This example displays the Filter parameters for the IP Application Type.

rtrv-ee-flt:appl=ip


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    EE OAM Filter Configuration
    IP FILTERS
    ----------------------------------------------------------------------------------
    ID  TYPE IP   IP              IP              SCTP  SCTP  SCTP  SCTP  SCTP
             PROT SRC             DST             SRC   DST   TYPE  DATA  DATA
                  ADDR            ADDR            PORT  PORT        PLD   STR
    ----------------------------------------------------------------------------------
    3    INC tcp   -               -               -     -     -    -     -
    8    EXC  -    -              3.3.3.3          -     -     -    -     -
    9    EXC  -    -              5.5.50.5         -     -     -    -     -
    18   INC sctp 10.248.13.9      -              1234   -     -    -     -
    19   INC sctp 10.248.13.9      -               -    1234   -    -     -
    32   INC sctp 10.248.13.9      -              1234   -    data m2pa   -
    34   INC sctp 111.248.131.119 111.111.111.111 1234  2345  data m2pa   -
    37   EXC sctp 111.248.131.119 111.111.111.111 1234  2345  data m2pa   -
    38   EXC sctp 111.248.131.119 111.111.111.111 1234  2345  data  -     -
    46   EXC sctp 10.248.13.9      -              1234   -    data m2pa   -
    50   EXC sctp 10.248.13.9      -              1234   -    data m2pa   -
    85   INC sctp  -               -               -     -    data sua    -

    EE Filter table is (83 of 200) 42% full.

;
Command Executed

This example displays the Filter parameters for the E1T1 Application Type.

rtrv-ee-flt:appl=e1t1


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    EE OAM Filter Configuration
    E1T1 FILTERS
    -----------------------------
    ID  TYPE PORT SUTYPE  MTP3SI
    -----------------------------
    6    INC a21   -      -
    7    INC a22   -      -
    12   INC a     -      -
    69   INC a31   -      -
    70   INC b31   -      -
    72   INC a    lsu     -
    EE Filter table is (83 of 200) 42% full.
;
Command Executed

This example displays the Filter parameters for all the configured Filters.

rtrv-ee-flt


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    EE Filter Configuration
    IP Filters
    ID  TYPE IP   IP              IP              SS    SD    STYPE SCTP  SCTP      
             PROT SRC             DST             PORT  PORT        PLD   STR
                  ADDR            ADDR
    -----------------------------------------------------------------------------------
    1   INC  SCTP 10.248.13.10    10.25.80.191    65535 10000 DATA  M2PA  65535
    47  EXC  SCTP 101.248.131.191 102.251.118.111 65432 10245 HTBT  -     -
    ATM Filters
    ID  TYPE  PORT SSCOPSU MTP3SI
    -----------------------------
    100 INC   A    DATA    SCCP
    105 EXC   B    CTRL    -
    E1T1 Filters
    ID  TYPE  PORT SUTYPE  MTP3SI
    -----------------------------
    2   INC   A1   MSU     SCCP
    EE FLT table is (5 of 200) 2% full
;
Command Executed

dlt-ee-flt

ent-ee-flt

rtrv-upgrade-config

Use this command to retrieve provisioned data used by the upgrade software during an upgrade of an in-service EAGLE from a source release to the target release.

Parameters

display (optional)

Display Indicator. This parameter indicates what type of output is to be displayed.

Range:

tblcnv: Displays a list of DMS tables that will be converted during the next upgrade. These tables are selected for conversion using the chg-upgrade-config command.
prtnstat: This parameter is not implemented at this time.
all: Display all upgrade configuration data.

Default:

all

Example

Display a list of DMS tables that will be converted during the next upgrade.

rtrv-upgrade-config:display=tblcnv

rtrv-upgrade-config

Dependencies

None

N/A N/A

Output


                rtrv-upgrade-config:display=tblcnv


    rlghncxa03w  07-03-13  08:15:45 EST  EAGLE 37.5.0
    The following tables will be converted:
         FEAT_CTRL Table, ID=327
    Command Completed. 
;

 rtrv-upgrade-config


    rlghncxa03w  10-02-13  08:15:45 EST  EAGLE 42.0.0
    Software Access Key no longer required for this system
    Configured Upgrade Threshold Type: SET  
    Command Completed. 
;

Related Topics

send-msg

Use this command to manually simulate a system generated message from a user terminal. The parameters (not entered by the user) are defaulted to:

Origination subsystem = cam_active
Destination subsystem = orig application ID=appl_ID_ui
Violation= no report
Bus = imt choice
Message length = computed

Parameters

da (mandatory)

The destination application ID.

Range:: 0 - 255

ds (mandatory)

The destination subsystem.

Range:: 0 - 255

f (mandatory)

The function ID.

Range:: 0 - 255

loc (mandatory)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1113, 1115, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118

alt (optional)

This parameter specifies whether to use the alternate bus bit.

Range:

on
off

Default:

on

bus (optional)

The IMT bus.

Range:

a
b

Default:

a

d0 (optional)

The application data.

Range:: 0 - 255

d1 (optional)

The application data.

Range:: 0 - 255

d2 (optional)

The application data.

Range:: 0 - 255

d3 (optional)

The application data.

Range:: 0 - 255

d4 (optional)

The application data.

Range:: 0 - 255

d5 (optional)

The application data.

Range:: 0 - 255

d6 (optional)

The application data.

Range:: 0 - 255

d7 (optional)

The application data.

Range:: 0 - 255

d8 (optional)

The application data.

Range:: 0 - 255

d9 (optional)

The application data.

Range:: 0 - 255

len (optional)

The message length in bytes.

Range:: 0 - 65535
Default:: Calculated

oa (optional)

The originating application ID.

Range:: 0 - 255
Default:: 2

os (optional)

The originating subsystem.

Range:: 0 - 255
Default:: 0

si (optional)

This parameter allows the service ID field in the violation indicator to be set.

Range:: 0 - 31
Default:: 0

sut (optional)

The signal unit type.

Range:: 0 - 9
Default:: 2

Example

send-msg:loc=1113:os=2:oa=h'28:ds=2:da=h'28:f=7

send-msg:loc=1113:ds=2:oa=h'17:da=h'30:f=11

send-msg:loc=1116:ds=2:oa=h'17::da=h'30:f=12

send-msg:loc=1101:ds=1:da=65:f=27:d0=78:si=3

send-msg:loc=6212:ds=2:oa=h'17:da=h'30:f=11

send-msg:loc=6312:ds=1:da=64:f=171

Dependencies

The value of the da parameter must be valid.

2205 E2205 Cmd Rej: Invalid destination application ID

The destination location must be equipped to receive messages.

2207 E2207 Cmd Rej: Location type cannot receive messages

Card locations xy09 and xy10 cannot be used with bus b and bus a, respectively.

2247 E2247 Cmd Rej: Bus parameter invalid

The value of the ds parameter must be valid.

2206 E2206 Cmd Rej: Invalid originating application ID

Notes

The bus and sut parameters must be used when sending a message to a MUX card.

If the bus parameter is not specified with a MUX card location on imt B (such as xy10), the bus b value is used instead of the bus a value.

Output


                send-msg:loc=1113:os=2:oa=h'28:ds=2:da=h'28:f=7


rlghncxa03w 01-03-13 15:01:02 EST 
0061.0019    CARD 1113 PSM    ADMIN   PSM became active 
;

 send-msg:loc=1113:ds=2:oa=h'17:da=h'30:f=11


rlghncxa03w 01-03-13 15:02:34 EST 
System Buffer sent has following attributes :
    Msg Length = H'0006
    Dest Card = H'00f4
    Orig Subsys = H'0002        Dest Subsys = H'0002
    Orig Appl ID = H'0017       Dest Appl ID = H'0030
    Func ID = H'000b            Bus/Alt/SUT = H’000b
          Violation Ind = H’0000 
User Message sent to location 1113. 
;

 send-msg:sut=7:loc=1110:ds=0:da=h'40:f=h'a3:d0=0:bus=b


    tekelecstp 06-01-11 11:39:15 EST  EAGLE 35.1.0
        System Buffer sent has following attributes :
        Msg Length = H'0010
        Dest Card = H'00ff
        Orig Subsys = H'0001            Dest Subsys = H'0000
        Orig Appl ID = H'0030           Dest Appl ID = H'0040
        Func ID = H'00a3                Bus/Ret/Sut = H'0087
        Violation Ind = H'0000
        User Message sent to location 1110.
        ;

 send-msg:loc=6212:ds=2:oa=h'17:da=h'30:f=11


    tekelecstp 12-05-11 11:39:15 EST  EAGLE 45.0.0
    System Buffer sent has following attributes :
        Msg Length = H'0006
        Dest Card = H'00f4
        Orig Subsys = H'0002        Dest Subsys = H'0002
        Orig Appl ID = H'0017       Dest Appl ID = H'0030
        Func ID = H'000b            Bus/Alt/SUT = H’000b
        Violation Ind = H’0000
    User Message sent to location 6212. 
;

None.

set-mem

Use this command to set values in memory in the communication and application processors. If a card is reloaded, these memory changes are lost.

Parameters

addr (optional)

The address, in the form of segment–offset.

Range:

segment-offset

segment—h’00–h’ffff

offset—h’00–h’ffff

byte (optional)

The byte value to write to the specified memory location(s).

Range:: 0–h’00–h’ff

card (optional)

The card location, in the form of GPLID–Subsystem ID.

Range:

GPLID–Subsystem ID

GPLID— atmhc, deirhc, erthc, glshc, hipr2, ipghc, iplhc, ipsg, ipshc, mcphc, oamhc, pktgen, sccphc, siphc, ss7hc, utility

Subsystem ID— a, b, act, stb, all

The OAMHC GPL can be specified with any of the subsystem IDs.

For all other GPLs, only the all subsystem ID is valid.

dword (optional)

A double word value to write to the specified memory location(s).

Range:: 0–h’00–h’ffffffff

fill (optional)

The number of times that the value is to be written to successive addresses.

Range:: 0 - 65535
Default:: 1

imt (optional)

The IMT address.

Range:: 0 - 254

loc (optional)

Location. The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115

mask (optional)

The mask that selects the bits that are to be included in the operation (op).

Range:: 0-0xFFFFFFFF
Default:: 0xFFFFFFFF

op (optional)

Operation. The operation performed in order to arrive at the final value in the memory location.

Range:

replace
and
or
x

Default:

replace

paddr (optional)

The physical offset of the memory address.

Range:: h’00–h’ffffffff

proc (optional)

The processor type.

Range:

appl: Application processor
com: Communication processor

Default:

appl

word (optional)

A word value to write to the specified memory location(s).

Range:: h’00–h’ffff

Example

set-mem:loc=1109:paddr=h’201000:byte=0:fill=1024

set-mem:card=hipr2-all:paddr=h’202000:word=h’2a:op=and:mask=h’fff

Dependencies

The loc, imt, or card parameter must be specified.

2214 E2214 Cmd Rej: Missing parameter - CARD, LOC, or IMT

Only one of the loc, imt, and card parameters can be specified in the command.

2217 E2217 Cmd Rej: More than one of CARD, LOC, and IMT specified

The card location specified by the loc parameter must be in the database.

2101 E2101 Cmd Rej: Card location is unequipped

All of the subsystem values can be specified with the OAMHC GPLID. The other GPLID values can be specified only with the all subsystem value.

2208 E2208 Cmd Rej: ALL only qualifier allowed with given card type

Values of 1114, 1116, 1117, and 1118 cannot be specified for the loc parameter.

2212 E2212 Cmd Rej: Invalid card type for this command

The byte, word, or dword parameter must be specified.

2210 E2210 Cmd Rej: Byte, WORD or DWORD must be entered

Only one of the byte, word, and dword parameters can be specified in the command.

2218 E2218 Cmd Rej: Only one of BYTE, WORD or DWORD may be entered

The paddr parameter cannot be specified for an SS7 LIM card.

N/A N/A

Memory Type of FWORD is NOT supported at this time.

2693 E2693 Cmd Rej: FWORD is not supported at this time

The addr and paddr parameters cannot be specified together in the command.

2694 E2694 Cmd Rej: Invalid combination of ADDR and PADDR specified

The value specified for the fill parameter cannot exceed 65535.

2017 E2017 Cmd Rej: <parm_desc> is out of range, <min>..<max> - <parm>

Notes

The imt parameter allows this command to be entered for a card that has not been configured in the system.

Output

set-mem:loc=6205:paddr=h'0345fe:byte=2


    rlghncxa03w 12-05-22 21:14:03 EST Rel 45.0.0
    SDS Response Code 22 from IMT Address H'00fd - command complete. 
;

Related Topics

disp-mem