4.82 chg-ip-lnk
Use this command to provision the IP link table.
Parameters
- loc (mandatory)
- Card location. The unique identifier of a specific
application subsystem located in the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1113, 1115
- auto (optional)
- Tells hardware whether to automatically determine
duplex and speed.
Note:
Always specify "auto=yes" for ports that connected to an ELAP. The corresponding ports on ExAP LAN switches should be configured accordingly to achieve the operational speed and duplex of 1Gbps and Full Duplex.
- ipaddr (optional)
- The IP address for the specified port. This is a TCP/IP address expressed in standard dot notation. IP addresses consist of the system’s network number and the machine’s unique host number. An example IP address is 192.126.100.5, where 192.126.100 is the network number and 5 is the machine’s host number.
- mcast (optional)
- Multicast Control. This parameter enables or disables multicast support for the interface. This parameter is necessary for INP, G-Port, and G-Flex to establish the connection from the Service Module card to the MPS system.
- submask (optional)
- The subnet mask of the IP interface in the form of
an IP address with a restricted range of values.
This parameter is mandatory when the ipaddr parameter is specified.
- Range:
- The value must be valid for the class of the entered IP address.
- Valid for Class A Networks
-
- 255.0.0
- 255.192.0
- 255.224.0
- 255.240.0
- 255.248.0
- 255.252.0
- 255.254.0
- 255.255.128.0
- Valid for Class A or B Networks
-
- 255.255.0.0
- 255.255.192.0
- 255.255.224.0
- 255.255.240.0
- 255.255.248.0
- 255.255.252.0
- 255.255.254.0
- 255.255.255.128
- Valid for Class A, B, or C Networks
-
- 255.255.255.0
- 255.255.255.192
- 255.255.255.224
- 255.255.255.240
- 255.255.255.248
- 255.255.255.252
- Default:
- If the ipaddr parameter is not
specified, there is no change to the parameter value. If a
host's IP address is known, the default subnet mask should be
chosen according to the details mentioned in the following
table:
Table 4-10 Default Subnet Mask Values
Network Class IP Network Address Range Default Subnet Mask A
1.0.0.0 to 127.0.0.0
255.0.0.0
B
128.0.0.0 to 191.255.0.0
255.255.0.0
C
192.0.0.0 to 223.255.255.0
255.255.255.0
- System Default:
- 0.0.0.0
Example
chg-ip-lnk:loc=1102:port=a:auto=yes
Dependencies
The value specified for the ipaddr parameter must already exist in the Host table.
The IP addresses for interface A, B, C, and D must be unique (a card cannot have two interfaces on the same network).
For IPSG on SLIC, card can have IP interface of same subnet for Port A and C, and for Port B and D.
At least one optional parameter must be specified.
If auto=yes is specified, then the duplex and speed parameters cannot be specified.
The value specified for the loc parameter must correspond to the location of a card that can run an IP application (other than the EROUTE application, which is not supported by this command). For a list of the cards and their associated applications, see Table A-9.
The card in the location (other than OAM locations) specified by the loc parameter must be inhibited before this command can be entered.
If the location specified by the loc parameter is an OAM card location, then the command can be entered while the card is in IN-SR status (as DB modifications are not allowed while the OAM is inhibited). However, the card needs to be re-initialized after the command in order for the changes to take effect.
Sockets cannot be assigned to the B interface for all cards except for those configured as IPSG.
The local ipaddr and submask values of either the A or B or C or D network cannot be
changed to an address that represents a different network if a default router and/or
other gateway routers are is assigned to the current local network (display with
rtrv-ip-card
and rtrv-ip-rte
).
The local IP address cannot be changed if the current
or new local host has open sockets or associations (the
open parameter set to
yes with the
ent/chg-assoc
command).
The IP address of an existing IP link entry in the IP Link table cannot be changed if it exists in the IP Host table.
An IP link entry must be provisioned in the IP Link table before an IP host entry can be provisioned with a corresponding IP address in the IP Host table.
The IP host entry must be deleted from the IP Host table before an IP link entry can be deleted from the IP Link table.
An existing IP link entry in the IP Link table cannot be deleted (ipaddr=0.0.0.0) if it exists in the IP Host table.
The IP network address specified by the
ipaddr and
submask parameters must be different
from the PVN and fast copy network addresses specified by the
pvn/pvnmask, fcna/fcnamask, and
fcnb/fcnbmask parameters (see the
chg-netopts
command).
The card in the location specified by the loc parameter must support the port specified by the port parameter.
The ipaddr and submask parameters must be specified together in the command.
The local IP address cannot be changed if the local
host associated with a diameter connection has open connections (the open
parameter set to
yes with the
chg-assoc
command and that association
is associated with a diameter connection in the DCONN table).
An IP address cannot be configured for the card if the card is provisioned as a GTT card.
Each IP address in the IP link table must be unique.
Speed = 1000 (1 Gbps link) can be specified for ExAP port and slic IPSG card. Also visualization port on SCCP and SFAPP card.
Each IP address entered into the IP Link table must be unique.
If the submask parameter is specified, the value given must be a valid subnet mask.
Notes
Interface A/D is used for ExAP connectivity and interface B/C is used for the signaling network on the SLIC card running the DEIR/EIR/SIP application.
When the
chg-ip-lnk
command is executed for an
OAM card location, the following message is displayed:
CAUTION: MCAP IP INFO HAS BEEN CHANGED, MANUAL RE-INITIALIZATION IS NEEDED
Output
chg-ip-lnk:loc=1102:port=a:auto=yes
chg-ip-lnk:loc=1102:port=a:auto=yes
Command entered at terminal #3.
;
tekelecstp 14-06-05 11:17:48 MST EAGLE5 46.0.0-65.20.0
CHG-IP-LINK: MASP B - COMPLTD
;
chg-ip-lnk:loc=1103:port=c:ipaddr=10.248.13.59:submask=255.255.255.0:auto=yes
chg-ip-lnk:loc=1103:port=c:ipaddr=10.248.13.59:submask=255.255.255.0:auto=yes
Command entered at terminal #18.
;
tekelecstp 16-05-25 11:51:03 MST EAGLE 46.4.0.0.0-69.1.0
CHG-IP-LINK: MASP B - COMPLTD
;
Related Topics