4.381 init-network
Use this command to reset all the network cards. The network cards are E5- TSMs and LIMs; that is, anything not part of the Maintenance and Administration Subsystem (MAS). This command resets all the network cards by reloading GPLs and data to the cards. Use of this command requires maintenance personnel to be located at the site.
Caution:
Using this command causes network nodal isolation; however, if the network nodal isolation is less than two seconds, it may not be detected and may not be reported. Also, in some cases when network nodal isolation has been detected and a large number of maintenance troubles are being reported, the network nodal isolation message may not be reported. An alarm is generated, however.Example
init-network
Dependencies
The MASP must be in either Upgrade Phase 3 mode or Full Function mode. (See the “Notes” section for this command for more information.)
The system database must be coherrent when this command is entered.
At least one card with the SS7ANSI or CCS7ITU application installed must exist with an in-service active signaling link.
The force=yes parameter must be specified to override the required four-card SS7ANSI or CCS7ITU configuration. The system then selects the best available of the remaining SS7ANSI or CCS7ITU cards.
This command cannot be entered during an Extended Bit Error Rate Test (BERT).
Notes
Upgrade Phase 3
Upgrade Phase 3mode means that the MASPs are running GPLs that match the major revision defined for the approved GPLs, but the other network processors are only prepared to be upgraded.
Full Function
Full Function mode means that all MASPs are running GPLs that match the major revision defined for the approved GPLs. Full Function mode is the normal operating mode for the MASP.
Output
The command output scrolls into the scroll area of your display contiguously. However, for purposes of this example, each part has an explanation preceding it.
init-network
rlghncxa03w 06-05-27 08:15:10 EST EAGLE 35.0.0
(Reports the selection of an alternate card.)
rlghncxa03w 06-05-27 08:15:10 EST EAGLE 35.0.0
1234.1107 SYSTEM INFO INW ALT card as first to be preloaded
CARD=1201 GPL=SS7ANSI
Report Date: 06-05-27 Time: 16:29:15
Reports the selection of a main card.
init-network
rlghncxa03w 06-05-27 08:15:10 EST EAGLE 35.0.0
1234.1108 SYSTEM INFO INW MAIN card as last to be reset
CARD=1202 GPL=SS7ANSI
Report Date: 06-05-27 Time: 16:29:17
Reports that the card cross loading is inhibited.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1109 SYSTEM INFO Asserted DDL inhibition
CARD=1113 GPL=OAM
Report Date: 06-05-27 Time: 16:27:18
Reports that a card reset has been issued.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1110 SYSTEM INFO Card reset command issued
CARD=1204 GPL=SS7ANSI
Report Date: 06-05-27 Time: 16:30:18
Reports that a card is being allowed to load.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1111 SYSTEM INFO Allowing card to load
CARD=1204 GPL=SS7ANSI
Report Date: 06-05-27 Time: 16:30:18
Reports that INW is waiting for validation of card loading.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1112 SYSTEM INFO Waiting for validation of card loading
CARD=1204 GPL=SS7ANSI
Report Date: 06-05-27 Time: 16:30:18
Reports that INW has detected successful completion of card loading.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1113 SYSTEM INFO Detected card loaded
CARD=1204 GPL=SS7ANSI
Report Date: 06-05-27 Time: 16:30:18
Reports that INW has detected the reset or removal of a card.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1114 SYSTEM INFO Detected card reset or removed
CARD=1204 GPL=SS7ANSI
Report Date: 06-05-27 Time: 16:30:18
Reports that the card is being allowed to crossload.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1115 SYSTEM INFO Allowed card to skip DDL inhibited
CARD=1204 GPL=SS7ANSI
Report Date: 06-05-27 Time: 16:30:18
Reports that DDL inhibition has been removed.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1116 SYSTEM INFO Removed DDL inhibition
CARD=1113 GPL=OAM
Report Date: 06-05-27 Time: 16:30:18
If init-network
is entered during an upgrade, reports that the upgrade is to continue.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1117 SYSTEM INFO Initialize OAMs to continue upgrade
CARD=1113 GPL=OAM
Report Date: 06-05-27 Time: 16:30:18
Reports that a card must be reset manually or removed.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1118 SYSTEM INFO Card must be manually reset/removed
CARD=1204 GPL=SS7ANSI
Report Date: 06-05-27 Time: 16:30:18
Reports that a card has failed to reset.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1119 SYSTEM INFO Card failed to reset
CARD=1204 GPL=SS7ANSI
Report Date: 06-05-27 Time: 16:30:18
Reports that a DDL inhibition assertion has failed.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
1234.1120 SYSTEM INFO Failed to assert DDL inhibition
CARD=1113 GPL=OAM
Report Date: 06-05-27 Time: 16:30:18
Reports that an internal error has stopped an init-network
.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
Command Aborted : Internal error.
Reports that a failure to load a card has stopped an init-network
.
init-network
rlghncxa03w 06-05-27 16:30:02 EST EAGLE 35.0.0
Command Aborted : Card 1206 failed to load.