4.424 rept-stat-rte
Use this command to display the signaling route status for a particular destination.
Parameters
- dpc (optional)
-
- Range:
- p-, 000-255, *, **, ***
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
prefix—p-
The asterisk values *, **, and *** are not valid for the ni subfield.
If ** or *** is specified for the nc subfield, either *, **, or *** must be specified for the ncm subfield.
When
chg-sid:pctype=ansiis specified, ni=000 is not valid.When
chg-sid:pctype=ansiis specified, nc=000 is not valid if ni=001-005.When
chg-sid:pctype=ansiis specified, nc=000 is valid if ni=006-255.When
chg-sid:pctype=ansiis specified, ni-*-* is valid if ni= 006-255.The point code 000-000-000 is not a valid point code.
- mode (optional)
- This parameter specifies the type of display to produce.
- Range:
-
- full
- Comprehensive display of point code status, including rtx. If specified with a point code, then the status for that point code is displayed. If specified without a point code, then the status of all routes is displayed.
- rtx
- Displays exception route status, other than circular routing, if the Origin-based MTP Routing feature is on.
- Default:
- A summary report is displayed.
Example
rept-stat-rte
rept-stat-rte:dpc=5-25-0
rept-stat-rte:dpci=5-5-0:mode=full
rept-stat-rte:dpci=5-5-0:mode=rtx
rept-stat-rte:mode=rtx
rept-stat-rte:mode=full
rept-stat-rte:dpc=5-25-**
rept-stat-rte:dpcn16=1-2-3
Dependencies
An x-list DPC cannot be specified in the dpc parameter.
If the mode=full parameter is specified, then the dpc/dpca/dpcn/dpci/dpcn24 parameter must be specified.
If the dpc parameter specifies an ni-nc-* format, then the mode parameter cannot be specified.
The dpc parameter must specify anni-nc-* format before the stat parameter can be specified with the dpc parameter.
No other rept-stat-xxx command can be in progress when this command is entered.
If a dpc parameter is specified, then the value must be the true destination point code (not an alias) and the value must be defined in the database.
The Origin-Based MTP Routing feature must be turned on before the mode=rtx parameter can be specified.
The destination address must be a full point code, a network destination, or a cluster point code.
The pst and mode parameters cannot be specified together in the command.
Notes
This command can be canceled using the F9 function key or the canc-cmd command. See canc-cmd for more information.
This command does not report the x-list point codes. Use the rept-stat-cluster command for a report of x-list point codes.
If the mode=rtx parameter is specified with a specific DPC, additional linkset, route and exception route information associated with the specified DPC is displayed.
In this command, only ITU-international and ITU national point codes support the spare point code subtype prefix (s-) and the private and spare point code subtype prefix (ps-). All of the point code types support the private (internal) point code subtype prefix (p-).
Summary of DPC parameter syntaxes
rept-stat-dstn:dpc=ni-nc-ncm—Requests a report for fully provisioned destinationni-nc-ncm.rept-stat-dstn:dpc= ni-*-*—Requests a report for provisioned network destination with the specified network indicator. If * is specified in the nc field,* must be specified in the ncm field.rept-stat-dstn:dpc= ni-**-*—Requests a report for the full network cluster for the specifiedni.rept-stat-dstn:dpc= ni-***-— Requests a report for the full network cluster and the network cluster address (if any) for the specified ni.rept-stat-dstn:dpc= ni-nc-*—Requests a report for provisioned cluster destination ni-nc-*.rept-stat-dstn:dpc= ni-nc-**—Requests a report showing all destinations whose network (ni) and cluster (nc) components match those specified. Note, however, that the network cluster address on ni-nc-* (if it exists) is not reported.rept-stat-dstn:dpc= ni-nc-***—Requests a report showing all destinations whose network (ni) and cluster (nc) components match those specified. The network cluster address (if it exists) is also reported.rept-stat-dstn:dpcn24=msa-ssasp—Requests a report for fully provisioned 24-bit destination pointmain signaling area-sub signaling area signaling point.
If the mode=rtx parameter is specified without a specific DPC, then status is provided for all exception route sets.
If the mode=full parameter is specified with a specific destination point code, then additional linkset, route, and exception route information associated with the specified destination is displayed, along with information that can be used to correct circular routing. If the mode=full parameter is specified without a specific destination point code, then status is provided for all regular and exception route sets.
Output
If the dpc parameter is not specified:
- If the mode parameter is not specified, then the command output lists the status of all provisioned destination point codes (DPCs) (routesets) in the system.
- If the mode=rtx parameter is specified, then the output lists the status of only those DPCs against which exception routes have been provisioned, and the status of the provisioned exception route sets associated with each DPCs.
- If the mode=full parameter is specified, then the command lists the status of all provisioned DPCs in the system, and the status of the provisioned exception route sets, if any, associated with each DPC.
If the dpc parameter is specified:
- If the mode parameter is not specified, then the output lists the status of all provisioned routes in the route set specified by that DPC.
- If the mode=rtx parameter is specified, then the output lists the status of all provisioned routes in the routeset specified by that DPC, and the status of all provisioned exception routesets associated with that DPC.
- If the mode=full parameter is specified, then the output lists the status of all provisioned routes in the routeset specified by that DPC, the status of all provisioned exception route sets associated with that DPC, any aliases associated with that DPC, and circular routing alarm information if any for that DPC.
This example shows how summary information for all provisioned cluster and noncluster DPCs is reported.
rept-stat-rte
tekelecstp 10-10-15 14:59:49 EST EAGLE 43.0.0
rept-stat-rte
Command entered at terminal #4.
Extended Processing Time may be Required
DPCA PST SST AST
001-001-003 OOS-MT Idle INACCESS
001-001-004 OOS-MT Idle INACCESS
001-001-005 OOS-MT Idle INACCESS
001-001-006 OOS-MT Idle INACCESS
001-001-007 OOS-MT Idle INACCESS
001-001-008 OOS-MT Idle INACCESS
001-001-009 OOS-MT Idle INACCESS
001-001-010 OOS-MT Idle INACCESS
001-001-011 OOS-MT Idle INACCESS
001-001-012 OOS-MT Idle INACCESS
001-001-013 OOS-MT Idle INACCESS
001-001-014 OOS-MT Idle INACCESS
001-001-015 OOS-MT Idle INACCESS
001-001-016 OOS-MT Idle INACCESS
001-001-017 OOS-MT Idle INACCESS
001-001-018 OOS-MT Idle INACCESS
001-001-019 OOS-MT Idle INACCESS
001-001-020 OOS-MT Idle INACCESS
001-001-021 OOS-MT Idle INACCESS
001-001-022 OOS-MT Idle INACCESS
001-001-023 OOS-MT Idle INACCESS
001-001-024 OOS-MT Idle INACCESS
001-001-025 OOS-MT Idle INACCESS
001-002-003 OOS-MT Idle INACCESS
DPCN PST SST AST
DPCN24 PST SST AST
DPCI PST SST AST
Command Completed.
;
This example shows how specifying a cluster destination on the dpc parameter shows the cluster status and routeset information. Information on cluster members (both provisioned and x-list) is not shown. Use the rept-stat-cluster command to obtain this information.
rept-stat-rte:dpc=9-3-*
rlghncxa03w 04-07-07 14:59:11 EST EAGLE 31.9.0
DPCA PST SST AST
009-003-* IS-NR Allowed ACCESS
ALARM STATUS = No Alarms.
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1* 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- -------- ***-***-*** -------- -------- --------
5 -- -------- ***-***-*** -------- -------- --------
6 -- -------- ***-***-*** -------- -------- --------
;
This example shows how specifying an FPC or cluster destination for which circular routing has been detected, along with the mode=full parameter, displays the name of the linkset on which the circular routing test message was transmitted. It also displays the linkset on which the circularly routed message was received.
rept-stat-rte:dpc=9-3-6:mode=full
rlghncxa03w 04-01-07 14:59:11 EST EAGLE 31.3.0
DPCA PST SST AST
009-003-006 OOS-MT Prohibit INACCESS
ALARM STATUS = = *C xxxx Circular routing detected
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- -------- ***-***-*** -------- -------- --------
5 -- -------- ***-***-*** -------- -------- --------
6 -- -------- ***-***-*** -------- -------- --------
SSN SUBSYSTEM STATUS
ALIASA ALIASN ALIASI
----------- ----------- -----------
CIRCULAR ROUTING
XMIT LSN= lsnstpb
RCV LSN= lsn01a
MEMBER= ***-***-***
Command Completed.
;
This example shows a typical report when a cluster destination and mode=full is specified. The interpretation of the circular routing status for cluster destinations is slightly different from the status for full point code destinations.
rept-stat-rte:dpc=9-3-*:mode=full
rlghncxa03w 04-01-07 14:59:11 EST EAGLE 31.3.0
DPCA PST SST AST
009-003-* IS-NR Allowed ACCESS
ALARM STATUS = *C xxxx Circular routing detected
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- -------- ***-***-*** -------- -------- --------
5 -- -------- ***-***-*** -------- -------- --------
6 -- -------- ***-***-*** -------- -------- --------
SSN SUBSYSTEM STATUS
ALIASA ALIASN ALIASI
----------- ----------- -----------
CIRCULAR ROUTING INFO:
XMIT LSN=lsnstpb RC=20
RCV LSN=lsn01a
MEMBER= 009-003-006
Command Completed.
;
This example shows how the circular routing alarm for a cluster destination is displayed. A circular routing alarm for a cluster destination indicates that circular routing was detected for a member of the cluster, but no x-list entry could be created for that cluster. Circular routing detected on a cluster destination does not automatically force the output to display the status of the cluster as “OOS-MT Prohibit INACCESS” as it does for a full point code destination.
rept-stat-rte:dpc=9-3-*
rlghncxa03w 04-01-07 14:59:11 EST EAGLE 31.3.0
DPCA PST SST AST
009-003-* IS-NR Allowed ACCESS
ALARM STATUS = *C xxxx Circular routing detected
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- -------- ***-***-*** -------- -------- --------
5 -- -------- ***-***-*** -------- -------- --------
6 -- -------- ***-***-*** -------- -------- --------
Command Completed.
;
This example shows how a subsystem information header is displayed without subsystem information, as when an FPC is specified without defining any subsystems. Because aliases cannot be defined for cluster destinations, this report shows only an empty header, as when an FPC is specified without defining aliases. The circular routing information portion of the report displays “--------” for the linkset names when no circular routing condition exists for the DPC.
rept-stat-rte:dpc=9-3-*:mode=full
rlghncxa03w 04-07-07 14:59:11 EST EAGLE 31.9.0
DPCA PST SST AST
009-003-* IS-NR Allowed ACCESS
ALARM STATUS = No Alarms.
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1* 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- -------- ***-***-*** -------- -------- --------
5 -- -------- ***-***-*** -------- -------- --------
6 -- -------- ***-***-*** -------- -------- --------
SSN SUBSYSTEM STATUS
ALIASA ALIASN ALIASI
----------- ----------- -----------
CIRCULAR ROUTING
XMIT LSN= --------
RCV LSN= --------
MEMBER= ***-***-***
Command Completed.
;
This example shows how specifying the stat parameter and the ni-nc-** or ni-nc-*** DPC formats causes the output summary report to include only those destinations whose status matches the state specified.
rept-stat-rte:dpc=9-4-***:stat=alminh
rlghncxa03w 10-10-29 13:30:00 EST EAGLE 43.0.0
rept-stat-rte:dpc=9-4-***:stat=alminh
Command entered at terminal #4.
Extended Processing Time may be Required
DPCA PST SST AST
009-004-006 IS-NR Allowed ALMINH
009-004-007 IS-NR Allowed ALMINH
.
.
.
009-004-056 IS-NR Allowed ALMINH
Command Completed.
;
This example shows a retrieval specifying an ITU national point code where the chg-stpopts:npcfmti parameter has been set to 1-1-1-11:
rept-stat-rte:dpcn=1-1-1-1000
rlghncxa03w 04-02-31 13:30:00 EST EAGLE 31.3.0
CAUTION : Node isolated...route status out of date!
DPCN PST SST AST
1-1-1-1000 OOS-MT Prohibit INACCESS
ALARM STATUS = *C 0313 DPC is prohibited
RTE COST LSN APCN LS STAT NON-ADJ ROUTE STAT
1 10 lsitu 1-1-1-1000 Prohibit Allowed Prohibit
2 -- -------- ***-***-*** -------- -------- --------
3 -- -------- ***-***-*** -------- -------- --------
4 -- -------- ***-***-*** -------- -------- --------
5 -- -------- ***-***-*** -------- -------- --------
6 -- -------- ***-***-*** -------- -------- --------
Command Completed.
;
This example shows a private adjacent point code:
rept-stat-rte:mode=full:dpc=1-1-2
rlghncxa03w 05-01-07 13:30:00 EST EAGLE 31.12.0
DPCA PST SST AST
001-001-002 OOS-MT Idle INACCESS
ALARM STATUS = No Alarms.
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1 01 ls11234567 001-001-002 Prohibit Allowed Prohibit
2 02 ls12345678 p-001-001-002 Prohibit Allowed Prohibit
3 -- ---------- ---***-***-*** -------- -------- --------
4 -- ---------- ---***-***-*** -------- -------- --------
5 -- ---------- ---***-***-*** -------- -------- --------
6 -- ---------- ---***-***-*** -------- -------- --------
SSN SUBSYSTEM STATUS
ALIASA ALIASN ALIASI
000-000-001 ----------- -----------
CIRCULAR ROUTING INFO:
XMIT LSN=---------- RC=--
RCV LSN=----------
MEMBER =-----------
Command Completed.
;
This example shows how the asterisks in the space after the route numbers in the following examples indicate which route (or combined route) is carrying traffic.
rept-stat-rte:dpc=1-1-1
tekelecstp 04-09-24 09:19:04 EST EAGLE 31.9.0
DPCA PST SST AST
001-001-001 IS-NR Allowed ACCESS
ALARM STATUS = No Alarms.
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1* 05 lse1e1 001-001-001 Allowed Allowed Allowed
2* 05 lse1e2 001-002-001 Allowed Allowed Allowed
3 10 lse1e3 001-003-001 Allowed Allowed Allowed
4 -- ---------- ---***-***-*** -------- -------- --------
5 -- ---------- ---***-***-*** -------- -------- --------
6 -- ---------- ---***-***-*** -------- -------- --------
Command Completed.
;
This example shows how no asterisk appears after the route number when no routes were carrying traffic.
rept-stat-rte:dpc=1-1-1
tekelecstp 06-05-24 09:19:04 EST EAGLE 35.0.0
DPCA PST SST AST
001-001-001 OOS-MT Prohibit INACCESS
ALARM STATUS = *C 0313 DPC is prohibited
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1 05 lse1e1 001-001-001 Prohibit Allowed Prohibit
2 05 lse1e2 001-002-001 Prohibit Allowed Prohibit
3 10 lse1e3 001-003-001 Prohibit Allowed Prohibit
4 -- ---------- ***-***-*** -------- -------- --------
5 -- ---------- ***-***-*** -------- -------- --------
6 -- ---------- ***-***-*** -------- -------- --------
Command Completed.
;
This example shows the output when the primary route is not carrying traffic.
rept-stat-rte:dpc=1-1-1
tekelecstp 06-05-24 09:19:04 EST EAGLE 35.0.0
DPCA PST SST AST
001-001-001 IS-ANR Restrict ACCESS
ALARM STATUS = *C 0334 DPC Subsystem is Abnormal
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1 05 lse1e1 001-001-001 Prohibit Allowed Prohibit
2 05 lse1e2 001-002-001 Prohibit Allowed Prohibit
3* 10 lse1e3 001-003-001 Allowed Allowed Allowed
4 -- ---------- ***-***-*** -------- -------- --------
5 -- ---------- ***-***-*** -------- -------- --------
6 -- ---------- ***-***-*** -------- -------- --------
Command Completed.
;
This example shows how the rtx mode displays all exception route sets provisioned against the specified DPC when the Origin-Based MTP Routing feature is enabled and on:
rept-stat-rte:dpc=9-3-*:mode=rtx
tekelecstp 09-05-01 16:21:39 EST EAGLE 41.0.0
DPCA PST SST AST
009-003-* IS-NR Allowed ACCESS
ALARM STATUS = No Alarms.
RTE COST LSN APCA LS STAT NON ADJ ROUTE STAT
1 10 lsnstpa 042-36-23 Allowed Allowed Allowed
2 20 lsnstpb 092-40-03 Allowed Allowed Allowed
3 30 lsnstpc 128-01-22 Prohibit Prohibit Allowed
4 -- -------- ***-**-** -------- -------- --------
5 -- -------- ***-**-** -------- -------- --------
6 -- -------- ***-**-** -------- -------- --------
Exception Routes:
OPCA PST SST AST
001-001-001 IS-NR Allowed ACCESS
ILSN PST SST AST
lsnstpy IS-NR Allowed ACCESS
Command Completed.
This example shows how all provisioned exception route sets are displayed in addition to the regular route sets when the Origin-Based MTP Routing feature is enabled and on and the full mode is specified.
rept-stat-rte:dpc=9-3-*:mode=full
tekelecstp 09-05-01 16:21:39 EST EAGLE 41.0.0
DPCA PST SST AST
009-003-006 OOS-MT Prohibit INACCESS
ALARM STATUS = = *C 0319 REPT-MTPLP-DET: Circ rte det(cong)
RTE COST LSN APCA LS STAT NON ADJ ROUTE STAT
1 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- -------- ***-***-*** -------- -------- --------
5 -- -------- ***-***-*** -------- -------- --------
6 -- -------- ***-***-*** -------- -------- --------
SSN SUBSYSTEM STATUS
ALIASA ALIASN ALIASI
-------------- -------------- --------------
CIRCULAR ROUTING INFO:
XMIT LSN=lsnstpb RC=20
RCV LSN=lsn01a
MEMBER =-----------
Exception Routes:
OPCA PST SST AST
001-001-001 IS-NR Allowed ACCESS
ILSN PST SST AST
lsnstpy IS-NR Allowed ACCESS
Command Completed.
;
This example shows how all provisioned exception route sets are displayed in addition to the regular route sets if the Origin-Based MTP Routing feature is enabled and on and the full mode is specified.
rept-stat-rte:mode=full
tekelecstp 10-10-01 14:06:10 EST EAGLE 43.0.0
rept-stat-rte:mode=full
Command entered at terminal #4.
Extended Processing Time may be Required
DPCA PST SST AST
004-004-004 OOS-MT Idle INACCESS
OPCA PST SST AST
001-001-001 IS-NR Allowed ACCESS
ILSN PST SST AST
lsnstpy IS-NR Allowed ACCESS
DPCN PST SST AST
00001 IS-NR Allowed ACCESS
SI PST SST AST
10 IS-NR Allowed ACCESS
00002 IS-NR Allowed ACCESS
00005 OOS-MT Prohibit INACCESS
00004 OOS-MT Prohibit INACCESS
DPCN24 PST SST AST
DPCI PST SST AST
Command Completed.
;
This example shows how all provisioned exception routes are displayed if the Origin-Based MTP Routing feature is enabled and on and the rtx mode is specified.
rept-stat-rte:mode=rtx
tekelecstp 10-10-29 14:06:10 EST EAGLE 43.0.0
rept-stat-dstn:mode=rtx
Command entered at terminal #4.
Extended Processing Time may be Required
DPCA PST SST AST
004-004-004 OOS-MT Idle INACCESS
OPCA PST SST AST
001-001-001 IS-NR Allowed ACCESS
ILSN PST SST AST
lsnstpy IS-NR Allowed ACCESS
DPCN PST SST AST
00001 IS-NR Allowed ACCESS
SI PST SST AST
10 IS-NR Allowed ACCESS
Command Completed.
;
This example shows the output of routes provisioned for ITU-N16.
rept-stat-rte:dpcn16=2-14-0
tekelecstp 02-05-08 03:18:02 EST UNKNOWN ??.?.?-64.71.1
CAUTION : Node isolated...route status out of date!
DPCN16 PST SST AST
002-14-00 OOS-MT Prohibit INACCESS
ALARM STATUS = *C 0313 DPC is prohibited
RTE COST LSN APC LS STAT NON-ADJ ROUTE STAT
1 10 ls1 002-14-00 Prohibit Allowed Prohibit
2 -- ---------- ---***-***-*** -------- -------- --------
3 -- ---------- ---***-***-*** -------- -------- --------
4 -- ---------- ---***-***-*** -------- -------- --------
5 -- ---------- ---***-***-*** -------- -------- --------
6 -- ---------- ---***-***-*** -------- -------- --------
Command Completed.
;
Legend
- DPC/DPCA—ANSI destination point code of the route
- DPCN—ITU-TSS national destination point code of the route
- DPCN24—24-bit ITU national destination point code of the route
- DPCN16--- 16-bit ITU national destination point code of the route
- DPCI—ITU-TSS international destination point code of the route
- OPC/OPCA—ANSI origination point code as exception routing criterion of the exception route
- OPCN—ITU-TSS national origination point code as exception routing criterion of the exception route
- OPCN24—24-bit ITU national origination point code as exception routing criterion of the exception route
- OPCI—ITU-TSS international origination point code as exception routing criterion of the exception route
- ILSN—Originating linkset as exception routing criterion of the exception route
- CIC—Starting Circuit Identification Code used as the exception routing criterion for this exception route
- ECIC—Ending Circuit Identification Code together with CIC defines the CIC range that is used as exception routing criterion for this exception route.
- PST—Primary state of the subsystem. See Possible Values for PST/SST/AST.
- SST—Secondary state of the subsystem. See Possible Values for PST/SST/AST.
- AST—Associated state of the subsystem. See Possible Values for PST/SST/AST.