4.405 rept-stat-dstn
Use this command to generate a report of the MTP point code status for provisioned point codes. Any provisioned destination can be specified, including a cluster destination (ni-nc-*) or a network destination (ni-*-*).
Parameters
Note:
See Point Code Formats and Conversion for a detailed description of point code formats, rules for specification, and examples.- dpc (optional)
- ANSI point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm). The prefix subfield indicates a private point code (prefix-ni-nc-ncm).
- Synonym:
- dpca
- Range:
- p-, 000-255, *, **, ***
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
prefix—p-
The asterisk values *, **, and *** are not valid for the ni subfield.
If ** or *** is specified for the nc subfield, either *, **, or *** must be specified for the ncm subfield.
When
chg-sid:pctype=ansiis specified, ni=000 is not valid.When
chg-sid:pctype=ansiis specified, nc=000 is not valid if ni=001-005.When
chg-sid:pctype=ansiis specified, nc=000 is valid if ni=006-255.When
chg-sid:pctype=ansiis specified, ni-*-* is valid if ni= 006-255.The point code 000-000-000 is not a valid point code.
- dpci (optional)
- ITU international point code with subfields zone-area-id. The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-zone-area-id).
- dpcn (optional)
- ITU national point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the
chg-stpopts:npcfmtiflexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- dpcn24 (optional)
- 24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp). The prefix subfield indicates a private point code (prefix-msa-ssa-sp).
- dpcn16 (optional)
- 16-bit ITU national point code with subfields unit number sub number area main number area (un-sna-mna). The prefix subfield indicates a private point code (prefix-un-sna-mna).
- mode (optional)
- The type of display to produce. This parameter displays the point code’s subsystem status along with the normal output.
- Range:
-
- full
- Comprehensive display of point code status, including rtx. If entered with a point code, status for that point code is displayed. If specified without a point code, the status of all routesets is displayed.
- rtx
- Displays exception route status, other than circular routing, if the Origin-based MTP Routing feature is on.
- Default:
- A summary report is displayed.
Example
rept-stat-dstn
rept-stat-dstn:dpci=2-004-1:mode=full
rept-stat-dstn:dpc=9-3-6:mode=full
rept-stat-dstn:dpc=9-3-*:mode=full
rept-stat-dstn:dpc=9-3-*
rept-stat-dstn:dpc=9-3-**
rept-stat-dstn:dpc=9-3-***
rept-stat-dstn:dpc=9-3-***:stat=mt
rept-stat-dstn:dpc:9-4-***:stat=alminh
rept-stat-dstn:dpc=9-3-*:mode=rtx
rept-stat-dstn:mode=full
rept-stat-dstn:mode=rtx
rept-stat-dstn:dpc=1-1-1
rept-stat-dstn:dpcn16=1-1-1
Dependencies
No other rept-stat-xxx command can be in progress when this command is entered.
If a dpc parameter is specified, it must be the true destination point code (not an alias) and it must be defined in the database.
The stat parameter can be specified with the dpc parameter only if the dpc parameter specifies one of the ni-nc-* formats.
An x-list DPC cannot be specified in the dpc parameter.
The mode=rtx parameter cannot be specified unless the Origin-Based MTP Routing feature is enabled and on.
The mode parameter cannot be specified with the dpc parameter if the dpc parameter specifies one of the ni-nc-* formats.
When the mode=full parameter is specified, the dpc/dpca/dpcn/dpci/dpcn24 parameter must be specified.
The destination address must be a full point code, a network destination, or a cluster point code.
Notes
This command can be canceled using the F9 function key or the canc-cmd command. See canc-cmd for more information.
This command does not report the x-list point codes. Use the rept-stat-cluster command for a report of x-list point codes.
If the mode=rtx parameter is specified with a specific DPC, additional linkset, route and exception route information associated with the specified DPC is displayed.
In this command, only ITU-international and ITU national point codes support the spare point code subtype prefix (s-) and the private and spare point code subtype prefix (ps-). All of the point code types support the private (internal) point code subtype prefix p-).
Summary description of the reports that are produced by the various DPC parameter syntaxes is shown:
rept-stat-dstn:dpc=ni-nc-ncm—Report for fully provisioned destination ni-nc-ncmrept-stat-dstn:dpc=ni-*-*—Report for provisioned network destination with the specified network indicator. If * is specified in the nc field, * must be specified in the ncm field.rept-stat-dstn:dpc=ni-**-*—Report for the full network cluster for the specified nirept-stat-dstn:dpc=ni-***-*—Report for the full network cluster and the network cluster address (if any) for the specified nirept-stat-dstn:dpc=ni-nc-*—Report for provisioned cluster destination ni-nc-*rept-stat-dstn:dpc=ni-nc-**—Report showing all destinations whose network (ni) and cluster (nc) components match those specified. The network cluster address ni-nc-* (if it exists) is not reported.rept-stat-dstn:dpc=ni-nc-***—Report showing all destinations whose network (ni) and cluster (nc) components match those specified. The network cluster address ni-nc-* (if it exists) is also reported.-
rept-stat-dstn:dpcn24=msa-ssa-sp—Report for fully provisioned 24-bit destination main signaling area-sub signaling area-signaling point
If the mode=rtx parameter is specified without a specific DPC, then status is provided for all exception route sets.
If the mode=full parameter is specified with a specific destination point code, then additional linkset, route, and exception route information associated with the specified destination is displayed, along with information that can be used to correct circular routing. If the mode=full parameter is specified without a specific destination point code, then status is provided for all regular and exception route sets.
Output
If the dpc parameter is not specified:
- If the mode parameter is not specified, then the command output lists the status of all provisioned destination point codes (DPCs) (routesets) in the system.
- If the mode=rtx parameter is specified, then the output lists the status of only those DPCs against which exception routes have been provisioned, and the status of the provisioned exception route sets associated with each DPCs.
- If the mode=full parameter is specified, then the command lists the status of all provisioned DPCs in the system, and the status of the provisioned exception route sets, if any, associated with each DPC.
If the dpc parameter is specified:
- If the mode parameter is not specified, then the output lists the status of all provisioned routes in the route set specified by that DPC.
- If the mode=rtx parameter is specified, then the output lists the status of all provisioned routes in the routeset specified by that DPC, and the status of all provisioned exception routesets associated with that DPC.
- If the mode=full parameter is specified, then the output lists the status of all provisioned routes in the routeset specified by that DPC, the status of all provisioned exception route sets associated with that DPC, any aliases associated with that DPC, and circular routing alarm information if any for that DPC.
This example shows the output when no parameters are specified:
rept-stat-dstn
tekelecstp 10-10-15 14:59:15 EST EAGLE 43.0.0
rept-stat-dstn
Command entered at terminal #4.
Extended Processing Time may be Required
DPCA PST SST AST
001-001-003 OOS-MT Idle INACCESS
001-001-004 OOS-MT Idle INACCESS
001-001-005 OOS-MT Idle INACCESS
001-001-006 OOS-MT Idle INACCESS
001-001-007 OOS-MT Idle INACCESS
001-001-008 OOS-MT Idle INACCESS
001-001-009 OOS-MT Idle INACCESS
001-001-010 OOS-MT Idle INACCESS
001-001-011 OOS-MT Idle INACCESS
001-001-012 OOS-MT Idle INACCESS
001-001-013 OOS-MT Idle INACCESS
001-001-014 OOS-MT Idle INACCESS
001-001-015 OOS-MT Idle INACCESS
001-001-016 OOS-MT Idle INACCESS
001-001-017 OOS-MT Idle INACCESS
001-001-018 OOS-MT Idle INACCESS
001-001-019 OOS-MT Idle INACCESS
001-001-020 OOS-MT Idle INACCESS
001-001-021 OOS-MT Idle INACCESS
001-001-022 OOS-MT Idle INACCESS
001-001-023 OOS-MT Idle INACCESS
001-001-024 OOS-MT Idle INACCESS
001-001-025 OOS-MT Idle INACCESS
001-002-003 OOS-MT Idle INACCESS
DPCN PST SST AST
DPCN24 PST SST AST
DPCI PST SST AST
Command Completed.
;
This example shows the output when a cluster destination on the dpc parameter is specified. This output shows the cluster status and routeset information. Information on cluster members is not shown. Use rept-stat-cluster to obtain this information.
rept-stat-dstn:dpc=9-3-*
tekelecstp 09-03-21 10:31:06 EST EAGLE 41.0.0
DPCA PST SST AST
009-003-* IS-NR Allowed ACCESS
ALARM STATUS = No Alarms.
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1* 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- -------- ***-***-*** -------- -------- --------
5 -- -------- ***-***-*** -------- -------- --------
6 -- -------- ***-***-*** -------- -------- --------
Command Completed.
;
This example shows the output for an FPC or cluster destination for which circular routing has been detected:
rept-stat-dstn:dpc=9-3-6:mode=full
tekelecstp 08-03-21 10:31:06 EST EAGLE 41.0.0
DPCA PST SST AST
009-003-006 OOS-MT Prohibit INACCESS
ALARM STATUS = *C xxxx Circular routing detected
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1* 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- ---------- ---***-***-*** -------- -------- --------
5 -- ---------- ---***-***-*** -------- -------- --------
6 -- ---------- ---***-***-*** -------- -------- --------
SSN SUBSYSTEM STATUS
ALIASA ALIASN ALIASI
-------------- -------------- --------------
CIRCULAR ROUTING INFO:
XMIT LSN= lsnstpb RC=--
RCV LSN= lsn01a
MEMBER= ***-***-***
Exception Routes:
Command Completed.
;
This example shows the outout when a cluster destination and the mode=full parameter is specified:
rept-stat-dstn:dpc=9-3-*:mode=full
tekelecstp 09-03-15 10:31:06 EST EAGLE 41.0.0
DPCA PST SST AST
009-003-* IS-NR Allowed ACCESS
ALARM STATUS = *C xxxx Circular routing detected
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1* 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- -------- ***-***-*** -------- -------- --------
5 -- -------- ***-***-*** -------- -------- --------
6 -- -------- ***-***-*** -------- -------- --------
SSN SUBSYSTEM STATUS
ALIASA ALIASN ALIASI
-------------- -------------- --------------
CIRCULAR ROUTING INFO:
XMIT LSN=lsnstpb RC=20
RCV LSN=lsn01a
MEMBER= 009-003-006
Exception Routes:
Command Completed.
;
This example shows the circular routing alarm for a cluster destination. The alarm indicates that circular routing was detected for a member of the cluster, but no x-list entry could be created for that cluster. Circular routing detected on a cluster destination does not automatically force the output to display the status of the cluster as “OOS-MT Prohibit INACCESS” as it does for an FPC destination.
rept-stat-dstn:dpc=9-3-*
stdcfg1a 09-03-16 14:09:24 EST EAGLE 41.0.0
DPCA PST SST AST
009-003-* IS-NR Allowed ACCESS
ALARM STATUS = *C xxxx Circular routing detected
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1* 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- ---------- ---***-***-*** -------- -------- --------
5 -- ---------- ---***-***-*** -------- -------- --------
6 -- ---------- ---***-***-*** -------- -------- --------
Command Completed.
;
This example shows the output if an FPC is specified for which no subsystems are defined. Also, because aliases cannot be defined for cluster destinations, this report shows only an empty header. The circular routing information portion of this report displays “--------” for the linkset names when no circular routing condition exists for the DPC.
rept-stat-dstn:dpc=9-3-*:mode=full
stdcfg1a 08-02-16 14:09:24 EST EAGLE 38.0.0
Command entered at terminal #4.
DPCA PST SST AST
009-003-* IS-NR Allowed ACCESS
ALARM STATUS = No Alarms.
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1* 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- ----------- ---***-***-*** -------- -------- --------
5 -- ----------- ---***-***-*** -------- -------- --------
6 -- ----------- ---***-***-*** -------- -------- --------
SSN SUBSYSTEM STATUS
ALIASA ALIASN ALIASI
-------------- -------------- --------------
CIRCULAR ROUTING INFO:
XMIT LSN= -------- RC=--
RCV LSN= --------
MEMBER= ***-***-***
Exception Routes:
Command Completed.
;
This example shows the output when the stat parameter and the ni-nc-** or ni-nc-*** DPC formats are specified. The output summary report includes only those destinations whose status matches the state specified.
rept-stat-dstn:dpc=9-4-***:stat=alminh
stdcfg1a 10-10-16 14:09:24 EST EAGLE 43.0.0
rept-stat-dstn:dpc=9-4-***:stat=alminh
Command entered at terminal #4.
Extended Processing Time may be Required
DPCA PST SST AST
009-004-006 IS-NR Allowed ALMINH
009-004-007 IS-NR Allowed ALMINH
.
.
.
009-004-056 IS-NR Allowed ALMINH
Command Completed.
;
This example shows the output for an ITU national point code where the chg-stpopts:npcfmti parameter has been set to 1-1-1-11:
rept-stat-dstn:dpcn=1-1-1-1000
stdcfg1a 09-03-16 14:09:24 EST EAGLE 41.0.0
CAUTION : Node isolated...route status out of date!
DPCN PST SST AST
1-1-1-1000 OOS-MT Prohibit INACCESS
ALARM STATUS = *C 0313 DPC is prohibited
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1 10 lsitu 1-1-1-1000 Prohibit Allowed Prohibit
2 -- ---------- ---***-***-*** -------- -------- --------
3 -- ---------- ---***-***-*** -------- -------- --------
4 -- ---------- ---***-***-*** -------- -------- --------
5 -- ---------- ---***-***-*** -------- -------- --------
6 -- ---------- ---***-***-*** -------- -------- --------
Command Completed.
;
The asterisks in the space after the route numbers in the following examples indicate which route (or combined route) is carrying traffic.
rept-stat-dstn:dpc=1-1-1
tekelecstp 09-03-24 09:19:04 EST EAGLE 41.0.0
DPCA PST SST AST
001-001-001 IS-NR Allowed ACCESS
ALARM STATUS = No Alarms.
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1* 05 lse1e1 001-001-001 Allowed Allowed Allowed
2* 05 lse1e2 001-002-001 Allowed Allowed Allowed
3 10 lse1e3 001-003-001 Allowed Allowed Allowed
4 -- ---------- ---***-***-*** -------- -------- --------
5 -- ---------- ---***-***-*** -------- -------- --------
6 -- ---------- ---***-***-*** -------- -------- --------
Command Completed.
;
No asterisk appears after the route number in the following example; no routes were carrying traffic at the time.
rept-stat-dstn:dpc=1-1-1
stdcfg1a 09-03-16 14:09:24 EST EAGLE 41.0.0
DPCA PST SST AST
001-001-001 OOS-MT Prohibit INACCESS
ALARM STATUS = *C 0313 DPC is prohibited
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1 05 lse1e1 001-001-001 Prohibit Allowed Prohibit
2 05 lse1e2 001-002-001 Prohibit Allowed Prohibit
3 10 lse1e3 001-003-001 Prohibit Allowed Prohibit
4 -- ---------- ***-***-*** -------- -------- --------
5 -- ---------- ***-***-*** -------- -------- --------
6 -- ---------- ***-***-*** -------- -------- --------
Command Completed.
;
This example shows the output when the Origin-Based MTP Routing feature is on, a specific DSTN is requested, and the rtx mode is specified:
rept-stat-dstn:dpc=9-3-*:mode=rtx
tekelecstp 09-05-01 16:21:39 EST EAGLE 41.0.0
DPCA PST SST AST
009-003-* IS-NR Allowed ACCESS
ALARM STATUS = No Alarms.
RTE COST LSN APCA LS STAT NON ADJ ROUTE STAT
1* 10 lsnstpa 042-36-23 Allowed Allowed Allowed
2 20 lsnstpb 092-40-03 Allowed Allowed Allowed
3 30 lsnstpc 128-01-22 Prohibit Prohibit Allowed
4 -- -------- ***-**-** -------- -------- --------
5 -- -------- ***-**-** -------- -------- --------
6 -- -------- ***-**-** -------- -------- --------
Exception Routes:
OPCA PST SST AST
001-001-001 IS-NR Allowed ACCESS
ILSN PST SST AST
lsnstpy IS-NR Allowed ACCESS
Command Completed.
;
This example shows the output when the Origin-Based MTP Routing feature is on, a specific DSTN is requested, and the full mode is used:
rept-stat-dstn:dpc=9-3-*:mode=full
stdcfg1a 09-05-16 14:09:24 EST EAGLE 41.0.0
DPCA PST SST AST
009-003-006 OOS-MT Prohibit INACCESS
ALARM STATUS = *C 0319 REPT-MTPLP-DET: Circ rte det(cong)
RTE COST LSN APCA LS STAT NON-ADJ ROUTE STAT
1* 10 lsnstpa 042-036-123 Allowed Allowed Allowed
2 20 lsnstpb 092-240-103 Allowed Allowed Allowed
3 30 lsnstpc 128-101-022 Allowed Allowed Allowed
4 -- ---------- ---***-***-*** -------- -------- --------
5 -- ---------- ---***-***-*** -------- -------- --------
6 -- ---------- ---***-***-*** -------- -------- --------
SSN SUBSYSTEM STATUS
ALIASA ALIASN ALIASI
-------------- -------------- --------------
CIRCULAR ROUTING INFO:
XMIT LSN=lsnstpb RC=20
RCV LSN=lsn01a
MEMBER =-----------
Exception Routes:
OPCA PST SST AST
001-001-001 IS-NR Allowed ACCESS
ILSN PST SST AST
lsnstpy IS-NR Allowed ACCESS
Command Completed.
;
This example shows the output when the Origin-Based MTP Routing feature is on, and the full mode is specified:
rept-stat-dstn:mode=full
tekelecstp 10-10-29 10:26:56 EST EAGLE 43.0.0
rept-stat-dstn:mode=full
Command entered at terminal #4.
Extended Processing Time may be Required
DPCA PST SST AST
001-001-000 OOS-MT Idle INACCESS
003-001-000 OOS-MT Idle INACCESS
002-102-001 OOS-MT Idle INACCESS
001-101-001 OOS-MT Idle INACCESS
OPCA PST SST AST
001-001-001 OOS-MT Idle INACCESS
002-001-000 OOS-MT Idle INACCESS
ILSN PST SST AST
e2m1s1 OOS-MT Idle INACCESS
CIC ECIC PST SST AST
0 1000 OOS-MT Idle INACCESS
SI PST SST AST
3 OOS-MT Idle INACCESS
003-101-001 OOS-MT Idle INACCESS
004-101-001 OOS-MT Idle INACCESS
007-101-001 OOS-MT Idle INACCESS
100-100-* OOS-MT Idle INACCESS
100-100-001 OOS-MT Idle INACCESS
OPCA PST SST AST
001-001-001 OOS-MT Idle INACCESS
002-002-002 OOS-MT Idle INACCESS
001-102-001 OOS-MT Idle INACCESS
200-200-001 OOS-MT Idle INACCESS
DPCN PST SST AST
1-010-1 OOS-MT Idle INACCESS
1-020-2 OOS-MT Idle INACCESS
1-020-3 OOS-MT Idle INACCESS
1-020-4 OOS-MT Idle INACCESS
1-050-1 OOS-MT Idle INACCESS
OPCA PST SST AST
002-001-000 OOS-MT Idle INACCESS
002-101-001 OOS-MT Idle INACCESS
DPCN24 PST SST AST
DPCI PST SST AST
1-030-1 OOS-MT Idle INACCESS
1-030-2 OOS-MT Idle INACCESS
1-040-4 OOS-MT Idle INACCESS
1-070-1 OOS-MT Idle INACCESS
OPCN PST SST AST
1-050-1 OOS-MT Idle INACCESS
ILSN PST SST AST
npc1 OOS-MT Idle INACCESS
Command Completed.
;
This example shows the output when the Origin-Based MTP Routing feature is on and the rtx mode is used:
rept-stat-dstn:mode=rtx
stdcfg1a 10-10-16 14:09:24 EST EAGLE 43.0.0
rept-stat-dstn:mode=rtx
Command entered at terminal #4.
Extended Processing Time may be Required
DPCA PST SST AST
001-101-001 OOS-MT Idle INACCESS
OPCA PST SST AST
001-001-001 OOS-MT Idle INACCESS
002-001-000 OOS-MT Idle INACCESS
ILSN PST SST AST
e2m1s1 OOS-MT Idle INACCESS
DPCN PST SST AST
1-050-1 OOS-MT Idle INACCESS
OPCA PST SST AST
002-001-000 OOS-MT Idle INACCESS
002-101-001 OOS-MT Idle INACCESS
DPCN24 PST SST AST
DPCI PST SST AST
1-070-1 OOS-MT Idle INACCESS
OPCN PST SST AST
1-050-1 OOS-MT Idle INACCESS
ILSN PST SST AST
npc1 OOS-MT Idle INACCESS
Command Completed.
;
This example shows the output when the mode=full parameter is specified, and the Origin-Based MTP routing feature is not turned on:
rept-stat-dstn:mode=full
tekelecstp 10-10-29 10:26:56 EST EAGLE 43.0.0
rept-stat-dstn:mode=full
Command entered at terminal #4.
Extended Processing Time may be Required
DPCA PST SST AST
001-001-001 OOS-MT Idle INACCESS
002-002-002 OOS-MT Idle INACCESS
003-003-003 OOS-MT Idle INACCESS
004-004-004 OOS-MT Idle INACCESS
005-005-005 OOS-MT Idle INACCESS
SI PST SST AST
3 OOS-MT Idle INACCESS
006-006-006 OOS-MT Idle INACCESS
007-007-007 OOS-MT Idle INACCESS
009-009-* OOS-MT Idle INACCESS
008-008-* OOS-MT Idle INACCESS
DPCN PST SST AST
00101 OOS-MT Idle INACCESS
00102 OOS-MT Idle INACCESS
00103 OOS-MT Idle INACCESS
00104 OOS-MT Idle INACCESS
00105 OOS-MT Idle INACCESS
00106 OOS-MT Idle INACCESS
00107 OOS-MT Idle INACCESS
DPCN24 PST SST AST
DPCI PST SST AST
2-100-1 OOS-MT Idle INACCESS
2-100-2 OOS-MT Idle INACCESS
2-100-3 OOS-MT Idle INACCESS
2-100-4 OOS-MT Idle INACCESS
2-100-5 OOS-MT Idle INACCESS
2-100-6 OOS-MT Idle INACCESS
2-100-7 OOS-MT Idle INACCESS
1-001-1 OOS-MT Idle INACCESS
1-001-2 OOS-MT Idle INACCESS
Command Completed.
;
This example shows the output when the mode=rtx parameter is specified, and the Origin-Based MTP Routing feature is not turned on:
rept-stat-dstn:mode=rtx
stdcfg1a 10-10-16 14:09:24 EST EAGLE 43.0.0
rept-stat-dstn:mode=rtx
Command entered at terminal #4.
Extended Processing Time may be Required
DPCA PST SST AST
005-005-005 OOS-MT Idle INACCESS
SI PST SST AST
3 OOS-MT Idle INACCESS
Command Completed.
;
rept-stat-dstn:dpcn16=1-1-1
stdcfg1a 09-03-16 14:09:24 EST EAGLE 41.0.0
DPCN16 PST SST AST
001-001-001 OOS-MT Prohibit INACCESS
ALARM STATUS = *C 0313 DPC is prohibited
RTE COST LSN APCN16 LS STAT NON-ADJ ROUTE STAT
1 05 lse1e1 001-001-001 Prohibit Allowed Prohibit
2 05 lse1e2 001-002-001 Prohibit Allowed Prohibit
3 10 lse1e3 001-003-001 Prohibit Allowed Prohibit
4 -- ---------- ***-***-*** -------- -------- --------
5 -- ---------- ***-***-*** -------- -------- --------
6 -- ---------- ***-***-*** -------- -------- --------
Command Completed.
;
Legend
- DPC/DPCA—ANSI destination point code of the route
- DPCN—ITU-TSS national destination point code of the route
- DPCN24—24-bit ITU national destination point code of the route
- DPCI—ITU-TSS international destination point code of the route
- OPC/OPCA—ANSI origination point code as exception routing criterion of the exception route
- OPCN—ITU-TSS national origination point code as exception routing criterion of the exception route
- OPCN24—24-bit ITU national origination point code as exception routing criterion of the exception route
- OPCI—ITU-TSS international origination point code as exception routing criterion of the exception route
- ILSN—Originating linkset as exception routing criterion of the exception route
- CIC—Starting Circuit Identification Code used as the exception routing criterion for this exception route
- ECIC—Ending Circuit Identification Code with CIC defines the CIC range used as exception routing criterion for this exception route
- PST—Primary state of the subsystem. See Possible Values for PST/SST/AST.
- SST—Secondary state of the subsystem. See Possible Values for PST/SST/AST.
- AST—Associated state of the subsystem. See Possible Values for PST/SST/AST.