rtrv-gttact

4.497 rtrv-gttact

Use this command to display entries from the Global Title Translations (GTT) Action table.

Parameters

Note:

Definitions for the feature options specified by the on and off parameters are located in the Notes section.

act (optional)

Action. The action applied to the message.

Range:

disc: discard message with no return error
dup: route a copy of the message to a specified duplicate node
fwd: route the original message to a specified forward node instead of the destination indicated by the GTT/ DB data
scpval: perform the SCCP MAP validation on MO/MT-FSM messages
sflog: send a copy of the original message to the SFLOG card
sfthrot: discard message if threshold exceeded
srvc: apply service (GPORT/GFLEX/SMSMR) on the message.
tcaperr: discard message that has a specified TCAP error
udts: discard message and send udts/xudts
sfapp: route message to SFAPP card

actid (optional)

GTT Action Id.

Range:: ayyyyyyyy
1 leading alphabetic followed by up to 8 alphanumeric characters

atcaperr (optional)

ANSI TCAP Error Cause. The reason for discarding the message containing the ANSI TCAP portion that is associated with the TCAPERR GTT Action.

Range:: 0 - 255

atirescgmodid (optional)

Calling party global title modification identifier for ATI. The GTMOD ID to be associated with the calling party of a SFAPP GTT Action entry.

Range:: ayyyyyyyy
1 leading alphabetic character followed by up to 8 alphanumeric characters
Default:: None

cdgtmodid (optional)

Called party global title modification identifier.

Range:: ayyyyyyyy
1 leading alphabetic character followed by up to 8 alphanumeric characters

cggtmodid (optional)

Calling party global title modification identifier.

Range:: ayyyyyyyy
1 leading alphabetic character followed by up to 8 alphanumeric characters

cgpc (optional)

ANSI point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm). The prefix subfield indicates a private point code (prefix-ni-nc-ncm).

Synonym:

cgpca

Range:

p-, 000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—p-

When chg-sid:pctype=ansi is specified, ni = 000 is not valid.

When chg-sid:pctype=ansi is specified, nc = 000 is not valid if ni = 001-005.

When chg-sid:pctype=ansi is specified, nc = 000 is valid if ni = 006-255.

The point code 000-000-000 is not a valid point code.

cgpci (optional)

ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-zone-area-id).

Range:

s-, p-, ps-, 0-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s-, p-, ps

zone—0-7

area—000-255

id—0-7

The point code 0-000-0 is not a valid point code.

cgpcn (optional)

ITU national point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the chg-stpopts:npcfmti flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).

Range:

s-, p-, ps-, 0-16383, aa-zz

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s-, p-, ps

nnnnn—0-16383

gc—aa-zz

m1-m2-m3-m4—0-14 for each member; values must sum to 14

cgpcn24 (optional)

24-bit ITU national point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp). The prefix subfield indicates a private point code (prefix-msa-ssa-sp).

Range:

p-, 000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—p

msa—000–255

ssa—000–255

sp—000–255

cgpcn16 (optional)

16-bit ITU national point code with subfields unit number-sub number area-main number area (un-sna-mna). The prefix subfield indicates a private point code (prefix- un-sna-mna).

Range:: p--, 000---127; Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).; prefix---p; un---000---127; sna---000---15; mna---000---31

cgpcogmsg (optional)

The data that is used as the Calling Party Point Code in the outgoing message.

Range:

cgpcicmsg: CgPA PC data from the incoming MSU
dflt: Default. The standard Global Title Translation process provides the CgPA PC.
opcicmsg: OPC data from the incoming MSU
provcgpc: provisioned CGPC/CGPCA/CGPCI/CGPCN/CGPCN24 data in the GTT Action
remove: CGPC will be removed from the outgoing MSU

defactid (optional)

Default Action ID. The Action ID associated with the Forward/SCPVAL/SFTHROT action.

Range:

disc: GTT Action ID of type disc
udts: GTT Action ID of type udts
tcaperr: GTT Action ID of type tcaperr
fallback: The MSU is routed using routing data in the incoming MSU when action is fwd. When action is set to scpval/sfthrot, the MSU is discarded.

failactid (optional)

Fail Action ID. The default action that is performed to route the message when the VLR Validation fails on Stateful App.

Range:

ayyyyyyyy

1 leading alphabetic character followed by 8 alphanumeric characters

The failactid parameter can take one of the following values:

GTT Action ID with a GTT Action of disc, udts or tcaperr (see the act parameter). This value must already be defined in the GTT Action table.
fallback -The MSU is discarded.

Default:

fallback

fwdgtt (optional)

Forward GTT. The forward GTT Action ID that is to be used to route the MSU.

Range:: ayyyyyyyy

hlraddr (optional)

It is used to address the HLR for the ATI message.

Range:: USECDPA --- Use the CDPA GTA from the query message; TCAPPARM --- GTT translation shall be performed on MAP Parameter. MAP parameter will be used in SCCP CDPA for GTT translation; FWDACT --- Route the message to a specified forward node indicated in FWD GTT Action ID
Default:: USECDPA

itcaperr (optional)

ITU TCAP Error Cause. The reason for discarding the message containing the ITU TCAP portion that is associated with the TCAPERR GTT Action.

Range:: 0 - 255

loopset (optional)

SCCP loopset name. This parameter retrieves action entries that are associated with the specified loopset.

Range:

ayyyyyyy

One alphabetic character followed by up to 7 alphanumeric characters.

none —Action entries with no association to any loopset.

mapset (optional)

MAP Set ID. The Mated Application Set ID.

Range:: 1 - 36000, dflt
dflt —Default MAP set

mrnset (optional)

MRN Set ID. The Mated Relay Node Set ID.

Range:

1 - 3000, dflt

dflt: Default MRN Set ID
none: The GTT Action table entry with no association to any mrnset.

off (optional)

Disables or turns off the specified feature options. A comma-separated list of feature options that are requested to be turned off. Up to 8 feature options can be specified in the list.

Range:

uimreqd
useicmsg
handlresp

on (optional)

Enables or turns on the specified feature options. A comma-separated list of feature options that are requested to be turned on. Up to 8 feature options can be specified in the list.

Range:

refcnt
uimreqd
useicmsg
handlresp

pc (optional)

ANSI point code in the form of network indicator-network cluster-network cluster member (ni-nc-ncm). The value "none" indicates that the Origin Point Code (OPC) field in the message will be used in place of CGPC.

Synonym:

pca

Range:

p-, 000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—p-

When chg-sid:pctype=ansi is specified, ni = 000 is not valid.

When chg-sid:pctype=ansi is specified, nc = 000 is not valid if ni = 001-005.

When chg-sid:pctype=ansi is specified, nc = 000 is valid if ni = 006-255.

The point code 000-000-000 is not a valid point code.

pci (optional)

ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-zone-area-id).

Range:

s-, p-, ps-, 0-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s-, p-, ps

zone—0-7

area—000-255

id—0-7

The point code 0-000-0 is not a valid point code.

pcn (optional)

ITU national point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the

chg-stpopts:npcfmti

flexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).

Range:

s-, p-, ps-, 0-16383, aa-zz

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—s-, p-, ps

nnnnn—0-16383

gc—aa-zz

m1-m2-m3-m4—0-14 for each member; values must sum to 14

pcn16 (optional)

16-bit ITU national point code with subfields unit number-sub number area-main number area (un-sna-mna). The prefix subfield indicates a private point code (prefix- un-sna-mna).

Range:: p--, 000---127; Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).; prefix---p; un---000---127; sna---000---15; mna---000---31

pcn24 (optional)

24-bit ITU national point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp). The prefix subfield indicates a private point code (prefix-msa-ssa-sp).

Range:

p-, 000-255

Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).

prefix—p

msa—000–255

ssa—000–255

sp—000–255

psirescgmodid (optional)

Calling party global title modification identifier for PSI. The GTMOD ID to be associated with the calling party of a SFAPP GTT Action entry.

Range:: ayyyyyyyy
1 leading alphabetic character followed by up to 8 alphanumeric characters
Default:: None

ri (optional)

Routing indicator.

Range:

gt
ssn

snai (optional)

The service nature of address indicator.

Range:

ccrndn: Country code, routing number, and national directory number
intl: International number
Natl: National significant number
rnidn: Routing number prefix and international dialed/directory number
rnndn: Routing number prefix and national dialed/directory number
rnsdn: Routing number prefix and subscriber dialed/directory number
Sub: Subscriber number

snp (optional)

The service numbering plan.

Range:

e164: E.164 numbering plan
e212: E.212 numbering plan
e214: E.214 numbering plan

sprm (optional)

SCCP Parameter. This parameter is used to decide whether the SCCP GTA, NP, and NAI (if GTI=4 and NP/NAI are present) will be picked up from CDPA or CGPA for comparison.

Range:

CDPA: SCCP CDPA GTA, NP, and NAI (if GTI=4 and NP/NAI are present) will be used for comparison
CGPA: SCCP CGPA GTA, NP, and NAI (if GTI=4 and NP/NAI are present) will be used for comparison

srvcerr (optional)

The action to be taken when the Service triggered by the GTT Action Service fails. The MSU can be processed by either applying the results of the pre-Service GTT, or continuing with the specific Service error processing.

Range:

SRVC: Continue with specific service error
GTT: Apply the result of pre-GTT service

Default:

SRVC

srvcname (optional)

Service to be applied on the MSU when act is set to srvc.

Range:: GFLEX, GPORT, SMSMR

ssn (optional)

Subsystem number.

Range:: 2 - 255, none

tprm (optional)

TCAP Parameter. This parameter is used to decide whether the MAP digits, NP, and NON (if NP and NON are present) will be picked up from SMRPDA or SMRPOA for comparison.

Range:

SMRPDA: MAP digits, NP, and NON (if NP and NON are present) from SMRPDA will be used for comparison
SMRPOA: MAP digits, NP, and NON (if NP and NON are present) from SMRPOA will be used for comparison

udtserr (optional)

UDTS error cause. This parameter specifies the reason for discarding the message that is associated with UDTS GTT Action.

Range:: 0 - 255

valtype (optional)

Validation Type. This parameter is used to decide whether SCCP/TCAP parameter should be used for the validation of the MSU or IR21.xml file data should be used for the validation of the MSU. This parameter can only be set for act=scpval.

Range:: sccptotcap; ir21totcap

Example

rtrv-gttact:actid=disc1

rtrv-gttact:cggtmodid=idda1

rtrv-gttact:cggtmodid=cggt1:cdgtmodid=cdgt2

rtrv-gttact:defactid=fallback

rtrv-gttact:pcn16=1-14-0

rtrv-gttact:act=srvc

rtrv-gttact:srvcname=gflex

rtrv-gttact:tprm=smrpda

rtrv-gttact:hlraddr=usecdpa:failactid=sfapp8

rtrv-gttact:hlraddr=fwdact

rtrv-gttact:hlraddr=tcapparm

rtrv-gttact:atirescgmodid=set1

rtrv-gttact:psirescgmodid=set5

rtrv-gttact:valtype=sccptotcap

Dependencies

The GTT Action table is corrupt or cannot be found.

The specified GTT Action entry must already exist in the database.

If the Flexible GTT Load Sharing feature is not enabled, then the mapset parameter cannot be specified.

The value specified for the pc/pca/pci/pcn/pcn24/pcn16 and cgpc/cgpca/cgpci/cgpcn/cgpcn24/cgpcn16 parameters must be a full point code and must have a valid value within the range for each subfield.

The Flexible GTT Load Sharing feature must be enabled before the mrnset parameter can be specified.

The mapset and mrnset parameters cannot be specified together in the command.

A value of none or fallback cannot be specified for the actid parameter.

A value of disc, udts, tcaperr, scpval, or sfapp must be specified for the act parameter before a value of uimreqd can be specified for the on or off parameter.

A value of dup or fwd must be specified for the act parameter before the pc, ssn, ri, mrnset, mapset, loopset, cgpc, cgpcogmsg, cggtmodid or cdgtmodid parameters can be specified.

A value of dup, fwd, scpval, or sfthrot must be specified for the act parameter before a value of useicmsg can be specified for the on or off parameter.

The act=fwd/scpval/sfthrot parameter must be specified before the defactid parameter can be specified.

The pc, ssn, ri, mrnset, mapset, loopset, cgpc, cgpcogmsg, defactid, tprm, and sprm parameters cannot be specified in the same command as the atcaperr, itcaperr, or udtserr parameters.

Values of useicmsg and uimreqd cannot be specified for the on or off parameters in the same command.

If the actid parameter is specified, then the ri, pc, ssn, mrnset, mapset, loopset, on, off, atcaperr, itcaperr, udtserr, act, cgpc, cgpcogmsg, defactid, cggtmodid, cdgtmodid, snp snai, srvcerr, srvcname, sprm, and tprm parameters cannot be specified.

The act=tcaperr parameter must be specified before the atcaperr or itcaperr parameter can be specified.

The act=udts parameter must be specified before the udtserr parameter can be specified.

The udtserr and srvcerr parameters cannot be specified in the same command.

The atcaperr and itcaperr parameters cannot be specified in the same command.

The pc, ri, ssn, mrnset, mapset, loopset, cdgtmodid, defactid, cgpc, cgpcogmsg, and cggtmodid parameters cannot be specified in the same command with the atcaperr, itcaperr, and udtserr parameters.

The srvcname, snp, snai and srvcerr parameters can only be specified when act is set to srvc.

The sprm and tprm parameters can be specified only when act is set to scpval.

The scfaddr, hlraddr, tt, failactid and fwdgtt parameters can only be specified if action type is sfapp.

The point code specified for the pc/pci/pcn/pcn24/pcn16 and cgpc/cgpci/cgpcn/cgpcn24/cgpcn16 parameters must be a full point code.

The SCCP Loop Detection feature must be enabled before the loopset parameter can be specified.

The value specified for the loopset parameter must already exist in the database.

The Loopset table is corrupt or cannot be found.

The value specified for the cdgtmodid or cggtmodid parameter must already exist in the GTMOD table.

The GTMOD table is corrupt or cannot be found.

The defactid=none or failactid=none parameter cannot be specified.

The value specified for the pc/pca/pci/pcn/pcn24/pcn16 and cgpc/cgpca/cgpci/cgpcn/cgpcn24/cgpcn16 parameters must have the same domain.

The same value cannot be specified for the on and off parameters.

The specified MAP set must already exist in the MAP table.

The specified MRN set must already exist in the MRN table.

A value of fwd, dup, or scpval must be specified for the act parameter before a value of useicmsg can be specified for the on or off parameter.

The value specified for the atirescgmodid and psirescgmodid parameters must already exist in the GTMOD table.

Notes

on/off options

uimreqd —UIM required. Specifies whether a UIM should be generated.
useicmsg —Use Incoming Message. Specifies whether to apply GTT Action data to the message as the message was received (OFF) or after any EPAP or GTT translation/modification data has been applied (ON).
handlresp —Specifies whether the ATI/PSI response will be sent to the SFAPP card or not.

Output

rtrv-gttact:on=refcnt


    tekelecstp 15-05-29 18:21:01 EST  EAGLE 46.3.0

    ACTID      ACTION   ATCAPERR ITCAPERR UDTSERR UIMREQD REFCNT
    ------------------------------------------------------------
    act2       disc     ---      ---      ---     off      0
    none1      disc     ---      ---      ---     off      0

    ACTID      ACTION     PCA         RI  SSN  MRNSET  MAPSET  REFCNT
    ---------------------------------------------------------------------------
    actdup1    dup      001-001-001   gt  ---  DFLT    -----   2
         CDGTMODID = ---------  CGGTMODID = ---------
         LOOPSET = None
         USEICMSG = off     CGPCOGMSG = dflt       CGPCA = ---
    actfwd1    fwd      001-001-001   gt  ---  DFLT    -----   2
         CDGTMODID = ---------  CGGTMODID = ---------
         LOOPSET = None     DEFACTID = Fallback
         USEICMSG = off     CGPCOGMSG = dflt       CGPCA = ---

    ACTID      ACTION     PCI         RI  SSN MRNSET  MAPSET  REFCNT

    ---------------------------------------------------------------------------
    ACTID      ACTION     PCN         RI  SSN MRNSET  MAPSET  REFCNT
    ---------------------------------------------------------------------------

    ACTID      ACTION     PCN24       RI  SSN MRNSET  MAPSET  REFCNT
    ---------------------------------------------------------------------------
    
    ACTID      ACTION   VALTYPE     NDGT    UIMREQD  USEICMSG   DEFACTID REFCNT
    ---------------------------------------------------------------------------
    scpval1    scpval   ir21totcap  ALL     off       off       DISCARD  0

    scpval2    scpval   sccptotcap  15      off       off       DISCARD  0
          TPRM = smrpda  SPRM = cdpa
           

    GTT-ACT  table is (2 of 2000) 1% full.

;

rtrv-gttact:cggtmodid=set1


    tekelecstp 10-02-04 18:21:01 EST  EAGLE 42.0.0
                                                                      
    ACTID      ACTION PCI             RI  SSN  MRNSET  MAPSET  
    ---------------------------------------------------------------------
    actdup2    DUP    002-002-002     GT  ---  2000    -----      
          CDGTMODID = set2      CGGTMODID = set1
    

    ACTID      ACTION PCN24           RI  SSN  MRNSET  MAPSET
    ---------------------------------------------------------------------------
    actdup6    DUP    111-222-333     SSN 100  ----    3000   
          CDGTMODID = id9       CGGTMODID = set1  

    GTT Action table is (8 of 2000) 1% full 

;

rtrv-gttact:pcn16=1-2-3


    tekelecstp 13-07-02 15:04:36 EST  45.0.0-64.69.0
    rtrv-gttact:pcn16=1-2-3
    Command entered at terminal #4.


    ACTID      ACTION   PCN16           RI  SSN  MRNSET  MAPSET
    -----------------------------------------------------------------------
    actfwd5    fwd      001-02-03       gt  ---  DFLT    -----
         CDGTMODID = ---------  CGGTMODID = ---------
         DEFACTID = Fallback
         USEICMSG = off     CGPCOGMSG = dflt       CGPCN16 = ---


    GTT-ACT  table is (1 of 2000) 1% full.

;

rtrv-gttact:srvcname=smsmr:act=srvc


    eagle1 13-10-27 18:10:25 EST  EAGLE 46.0.0

   ACTID      ACTION   SRVCNAME    SRVCERR    SNP    SNAI
   ----------------------------------------------------------------
   actsrvc1   srvc     GFLEX       SRVC       E212   SUB
   actsrvc4   srvc     GPORT       SRVC       E164   INTL
   actsrvc5   srvc     GPORT       GTT        E164   RNNDN
   actsrvc6   srvc     SMSMR       SRVC       E164   INTL
   actsrvc7   srvc     SMSMR       GTT        E164   RNNDN

;

rtrv-gttact:act=scpval


    tekelecstp 15-05-29 18:21:01 EST  EAGLE 46.9.0

        ACTID      ACTION   VALTYPE     NDGT    UIMREQD   USEICMSG   DEFACTID    
	 ---------------------------------------------------------------------    
	scpval1    scpval   ir21totcap  ALL     off       off        DISCARD    
 
	scpval2    scpval   sccptotcap  15      off       off        DISCARD          
		TPRM = smrpda  SPRM = cdpa 
     	
	GTT-ACT  table is (2 of 2000) 1% full.
;

rtrv-gttact:act=sfthrot


    tekelecstp 15-05-29 18:21:01 EST  EAGLE 46.3.0

    ACTID      ACTION  THRESHOLD  BURSTS DEFACTID
    ---------------------------------------------------------
    act1       sfthrot  1         0   disc1
    act2       sfthrot  1         2   disc2
    act3       sfthrot  1         1   disc3
    act4       sfthrot  20        0   disc4


    GTT-ACT  table is (4 of 2000) 1% full.

;

rtrv-gttact:hlraddr=usecdpa

tekelecstp 17-11-22 14:55:02 EST  EAGLE 46.5.1.5.0-73.2.0
    rtrv-gttact:hlraddr=usecdpa
    Command entered at terminal #17.
;
Command Accepted - Processing
    tekelecstp 17-11-22 14:55:02 EST  EAGLE 46.5.1.5.0-73.2.0

    ACTID      ACTION   DEFACTID   USEICMSG   NDGT   UIMREQD
    ----------------------------------------------------------------
    sfapp1     sfapp    FALLBACK   off        ALL    off
          SCFADDR = 18                 FAILACTID = DISCARD
          HLRADDR = USECDPA
    sfapp8     sfapp    FALLBACK   off        ALL    off
          SCFADDR = 19                 FAILACTID = DISCARD
          HLRADDR = USECDPA
    sfapp9     sfapp    FALLBACK   off        ALL    off
          SCFADDR = 19                 FAILACTID = DISCARD
          HLRADDR = USECDPA
    sfapp10    sfapp    FALLBACK   off        ALL    off
          SCFADDR = 19                 FAILACTID = DISCARD
          HLRADDR = USECDPA
    sfapp13    sfapp    FALLBACK   off        ALL    off
          SCFADDR = 16                 FAILACTID = DISCARD
          HLRADDR = USECDPA

    GTT-ACT  table is (11 of 2000) 1% full.
;
Command Executed

rtrv-gttact:failactid=fallback

tekelecstp 17-11-22 14:56:30 EST  EAGLE 46.5.1.5.0-73.2.0
    rtrv-gttact:failactid=fallback
    Command entered at terminal #17.
;
Command Accepted - Processing
    tekelecstp 17-11-22 14:56:30 EST  EAGLE 46.5.1.5.0-73.2.0

    ACTID      ACTION   DEFACTID   USEICMSG   NDGT   UIMREQD
    ----------------------------------------------------------------
    sfapp1     sfapp    FALLBACK   off        ALL    off
          SCFADDR = 18                 FAILACTID = DISCARD
          HLRADDR = USECDPA
    sfapp8     sfapp    FALLBACK   off        ALL    off
          SCFADDR = 19                 FAILACTID = DISCARD
          HLRADDR = USECDPA
    sfapp9     sfapp    FALLBACK   off        ALL    off
          SCFADDR = 19                 FAILACTID = DISCARD
          HLRADDR = USECDPA
    sfapp10    sfapp    FALLBACK   off        ALL    off
          SCFADDR = 19                 FAILACTID = DISCARD
          HLRADDR = USECDPA
    sfapp13    sfapp    FALLBACK   off        ALL    off
          SCFADDR = 16                 FAILACTID = DISCARD
          HLRADDR = USECDPA

    GTT-ACT  table is (11 of 2000) 1% full.
;
Command Executed

rtrv-gttact:atirescgmodid=set1

    tekelecstp 18-05-07 10:48:35 EST  EAGLE 46.7.0.0.0-74.5.0
    rtrv-gttact:atirescgmodid=set1
    Command entered at terminal #4.



    ACTID      ACTION   DEFACTID      NDGT   UIMREQD
    ----------------------------------------------------------------
    sfapp10    sfapp    FALLBACK      ALL    off
          SCFADDR = 19                 FAILACTID = DISCARD
          HLRADDR = USECDPA
          ATIRESCGMODID = set1       PSIRESCGMODID = ---------
          HANDLRESP = ON


    GTT-ACT  table is (3 of 2000) 1% full.

;

rtrv-gttact:psirescgmodid=set5

tekelecstp 18-05-07 10:48:35 EST  EAGLE 46.7.0.0.0-74.5.0
    rtrv-gttact:atirescgmodid=set5
    Command entered at terminal #4.



    ACTID      ACTION   DEFACTID      NDGT   UIMREQD
    ----------------------------------------------------------------
    sfapp10    sfapp    FALLBACK      ALL    off
          SCFADDR = 19                 FAILACTID = DISCARD
          HLRADDR = USECDPA
          ATIRESCGMODID = ---------    PSIRESCGMODID = set5
          HANDLRESP = ON



    GTT-ACT  table is (3 of 2000) 1% full.

;

rtrv-gttact:valtype=ir21totcap

    
		tklc1131001 20-01-29 02:18:02 HST  EAGLE 46.9 
    
		ACTID      ACTION   VALTYPE     NDGT    UIMREQD   USEICMSG   DEFACTID    
		---------------------------------------------------------------------    
		scpval1    scpval   ir21totcap  ALL     off       off        DISCARD      

		GTT-ACT  table is (2 of 2000) 1% full. 
;

Related Topics