4.533 rtrv-ls
Use this command to show the linkset information.
Parameters
- apc (optional)
- ANSI point code with subfields
network
indicator-network cluster-network cluster member (ni-nc-ncm). The prefix
subfield indicates a private point code (prefix-ni-nc-ncm).
- Range:
- p-, 000-255
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
prefix—p-
When
chg-sid:pctype=ansiis specified, ni = 000 is not valid.When
chg-sid:pctype=ansiis specified, nc = 000 is not valid if ni = 001-005.When
chg-sid:pctype=ansiis specified, nc = 000 is valid if ni = 006-255.The point code 000-000-000 is not a valid point code.
- apci (optional)
- ITU international point code with subfields zone-area-id. The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-zone-area-id).
- apcn (optional)
- ITU national point code in the format of a 5-digit
number (nnnnn); or 2, 3,
or 4 numbers (members)
separated by dashes (m1-m2-m3-m4) as defined by
the
chg-stpopts:npcfmtiflexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- apcn24 (optional)
- 24-bit ITU national point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp). The prefix indicates a private point code (prefix-msa-ssa-sp).
- apcn16 (optional)
- 16-bit ITU national point code with subfields unit number sub number area main number area (un-sna-mna). The prefix indicates a private point code (prefix-un-sna-mna).
- cggtmod (optional)
- Calling party GT modification indicator. This parameter displays the linksets that have the specified value of the calling party GT modification indicator.
- islsrsb (optional)
- Incoming rotated signaling link selection (SLS) bit. This parameter displays the linksets with the specified rotated bit.
- itutfr (optional)
- ITU TFR (Transfer Restricted) procedure indicator.
This parameter displays the linksets that have the specified value of the
itutfr parameter.
This parameter is valid for ITU national linksets only.
- lst (optional)
- Linkset type. This parameter specifies whether to
display proxy links.
This parameter can be specified only when the Proxy Point Code feature is enabled.
- mtprse (optional)
- ANSI or ITU MTP Restart equipped. This parameter specifies whether the node adjacent to the linkset is equipped with MTP Restart.
- pct (optional)
-
This parameter displays the linksets where the Point Code and CIC Translation has the specified status.
- ppc (optional)
- ANSI proxy point code with subfields
network
indicator-network cluster-network cluster member (ni-nc-ncm).
The proxy point code must be a full point code.
- Synonym:
- ppca
- Range:
- 000-255
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
When
chg-sid:pctype=ansiis specified, ni = 000 is not valid.When
chg-sid:pctype=ansiis specified, nc = 000 is not valid if ni = 001–005.When
chg-sid:pctype=ansiis specified, nc = 000 is valid if ni = 006–255.The point code 000-000-000 is not a valid point code.
- ppc/ppca/ppci/ppcn/ppcn24/ppcn16 (optional)
- Proxy Point Code.
The proxy point code must be a full point code.
- ppci (optional)
- ITU international proxy point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).
- ppcn (optional)
- ITU national proxy point code in the format of a
5-digit number (nnnnn);
or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by
the
chg-stpopts:npcfmtiflexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- ppcn24 (optional)
- 24-bit ITU national point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).
- ppcn16 (optional)
- 16-bit ITU national point code with subfields unit number-sub number area-main number area (un-sna-mna).
- randsls (optional)
- Random SLS (signaling link selection). This
parameter displays linksets that have the specified value of the
randsls parameter.
- Range:
-
- off
- Displays all linksets where random SLS is disabled.
- class0
- Displays linksets where random SLS generation for Class0 SCCP traffic is enabled.
- all
- Displays ITU linksets where random SLS generation for Class0 and Class1 SCCP traffic is enabled and ANSI linksets where random SLS generation for Class0 and ISUP traffic is enabled.
- Default:
- off
- slsocbit (optional)
- Other CIC (Circuit Identification Code) Bit. This parameter displays the linksets that have the slsocbit parameter set to a value from 5 - 16.
- slsrsb (optional)
- Rotated SLS (Signaling Link Selection) Bit. This parameter displays the linksets with the specified rotated bit.
- spc (optional)
- ANSI secondary point code with subfields
network
indicator-network cluster-network cluster member (ni-nc-ncm).
- Range:
- 000-255
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
When
chg-sid:pctype=ansiis specified, ni = 000 is not valid.When
chg-sid:pctype=ansiis specified, nc = 000 is not valid if ni = 001–005.When
chg-sid:pctype=ansiis specified, nc = 000 is valid if ni = 006–255.The point code 000-000-000 is not a valid point code.
- spci (optional)
- ITU international secondary point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).
- spcn (optional)
- ITU national secondary point code in the format of
a 5-digit number (nnnnn);
or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by
the
chg-stpopts:npcfmtiflexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
Example
Display all linksets having the parameter pct=on:rtrv-ls:pct=on
Display the attributes of all link sets:
rtrv-ls
Retrieve linkset LS1:
rtrv-ls:lsn=ls1
Retrieve all link sets with the mtprse=yes parameter:
rtrv-ls:mtprse=yes
Retrieve all link sets that use the slsocbit parameter with a value from 5 - 16:
rtrv-ls:slsocbit=*
Display an ITU linkset to view the settings for the slsrsb or slsocbit parameters:
rtrv-ls:lsn=lsitu
Retrieve all ITU national linksets that have the itutfr parameter set to on:
rtrv-ls:itutfr=on
Retrieve the specified ITU national linkset and display its setting for the itutfr parameter:
rtrv-ls:lsn=lsitun
Retrieve all linksets where random SLS generation is enabled for SCCP ITU traffic and Class0 ANSI traffic:rtrv-ls:randsls=class0
Display all proxy linksets:rtrv-ls:lst=prx
Display all linksets using a specified proxy point code:rtrv-ls:ppc=11-11-11
Display all linksets using a specified secondary point code:rtrv-ls:spc=2-2-2
Display all linksets using a specified adjacent point code:rtrv-ls:apc=1-1-2
Retrieves all linksets where calling party global title modification is requested:rtrv-ls:cggtmod=yes
Retrieves all link sets with the ISLSRSB value 6:rtrv-ls:islsrsb=6
Display all linksets using a specified adjacent point code:
rtrv-ls:apcn16=121-10-15
Dependencies
A PCT quantity feature must be enabled before the pct parameter can be specified.
The specified linkset must be in the database.
The Linkset table is corrupt or cannot be found.
All optional parameters, except for the combination of the slsocbit and slsrsb parameters, can only be used individually. Any combination of 2 or more of the optional parameters, other than the specified exception, is invalid.
If the
apcn parameter is specified as the
Adjacent Point Code, then the format of the
apcn
parameter must match the format dictated by the
chg-stpopts:npcfmti
parameter.
The SLSOCB feature must be enabled before the slsocbit parameter can be specified.
The Multiple Linksets to Single Adjacent PC (MLS) feature must be turned on before the apc and spc parameters can be specified.
A NULL pointer was sent into a function. An ATH will also be issued.
The Signaling Link table is corrupt or cannot be found.
The extended link table is corrupt or cannot be found.
The STPOPTS table is corrupt or cannot be found.
At least one linkset must be associated with the value of the apc parameter.
The Proxy Point Code feature must be enabled before the lst=prx parameter can be specified.
The Proxy Point Code feature must be enabled before the ppc parameter can be specified.
The value specified for the ppc parameter must be a full point code.
The value specified for the ppc parameter must already exist in the Destination table, and the prx=yes parameter must have been specified.
The value specified for the apc parameter must be a full point code.
The value specified for the spc parameter must be a full point code.
The AMGTT feature or the AMGTT CgPA Upgrade feature must be turned on before the cggtmod parameter can be specified.
The ISLSRSB feature must be enabled before the islsbr parameter can be specified.
The PPC specified must not be a private point code.
Notes
This command can be canceled using the
F9 function key
or the
canc-cmd
command. See
canc-cmd
for more information.
The CLLI, TFATCABMLQ, MTPRSE, and ASL8 fields are displayed only when a specific linkset is specified. The SLSOCBIT and SLSRSB fields are displayed only when a specific linkset is specified, and the linkset must be an ITU linkset.
If the tfatcabmlq parameter database value is 0 for a linkset, then the value displayed is one-half (rounded-up) of the number of links assigned to the given linkset (or 1 if there are 2 or fewer links in the linkset).
If the
tfatcabmlq parameter database value
is 0, then the TFA/TCA broadcast minimum link quantity is calculated by the
EAGLE to be a minimum of 1 for linksets containing 2 or fewer links, or half
(rounded-up) of the number of links configured in the linkset for linksets
containing more than 2 links. The calculated value is displayed in the
rtrv-ls
command output.
If the
tfatcabmlq parameter value is set to
a specific value greater than 0, then the EAGLE does not calculate a TFA/TCA
broadcast minimum link quantity. The provisioned value is displayed in the
rtrv-ls
command output.
The EAGLE
ent-ls
command allows 10-character linkset names, but entering a
linkset name through SEAS is still restricted to 8 characters. In SEAS, a
specific linkset with a name greater than 8 characters (entered using the EAGLE
command) cannot be retrieved by name. If an asterisk is used for the linkset
name in the SEAS
vfy-ls
command, all linksets will be shown; however, the linkset
names that are more than 8 characters will have only the first 8 characters
shown. Therefore it may appear that there are duplicate linkset names in SEAS
vfy-ls
output, but all linkset names are actually unique.
In this command, only ITU-international and ITU national point codes support the spare point code subtype prefix (s-) and the private and spare point code subtype prefix (ps-). All of the point code types support the private (internal) point code subtype prefix (p-).
The value specified for the ppc parameter must be a full point code. Cluster point codes and private point codes are not supported.
The ICNIMAP and OGNIMAP fields are displayed only if the linkset name is specified in the command, the ITU Spare Point Code feature is enabled, and an ITUN or ITUI point code is associated with the linkset.
IPSG linksets have SLKTPS configured. SLKTPS configures the transactions per second for each link assigned to the IPSG linkset. For an IPSG linkset, the calculated IP TPS value (shown under the 'CONFIG' column in the report) is made up of the aggregate calculated SLKTPS of all of the provisioned links in the linkset. Non-IPSG hosted links are not counted in the calculation as they do not support SLKTPS.
If a linkset contains a mixture of IPLIMx M2PA and IPSG-M2PA links, then the command does not report any data below the TPS header or raise alarms.
Output
The Multiple Linksets to Single Adjacent PC (MLS) feature must be turned on before information can be retrieved for an adjacent point code or a secondary point code.
The Proxy Point Code feature must be enabled before information can be retrieved by proxy point code or proxy linkset.
If information is requested for a linkset, then the secondary point code field is displayed in the output. If the MLS feature is not enabled, or if the linkset was not created with a secondary point code, the field contains dashes.
Headings for unequipped cards are not displayed.
This example shows all linksets where random SLS generation is enabled for Class0 and Class1 SCCP traffic for ITU linksets and Class0 and ISUP traffic for ANSI linksets:
rtrv-ls:randsls=all
tekelecstp 10-03-06 19:36:00 EST EAGLE 42.0.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsa111 001-001-001 none 1 1 no B 0 off off off no off
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsi111 1-001-1 none 1 2 no B 0 off off off no off
Link set table is (2 of 1024) 1% full.
;
This example shows detailed linkset configuration for linkset LSI111. Random SLS generation is enabled for Class0 and Class1 SCCP traffic:
rtrv-ls:lsn=lsi111
tekelecstp 18-01-22 05:29:51 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsi111 1-000-1 none 1 2 no A 0 off off off no off
SPCI CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 1 --- ---
SLSRSB RANDSLS ITUTFR
1 all off
IPSG GTTMODE CGGTMOD
no CdPA no
Link set table is (1 of 1024) 1% full.
;
This example shows detailed linkset configuration for linkset LS4. Random SLS generation is enabled for SCCP Class0 traffic, and the SLSOCB and the ITUDUPPC features are turned on:
rtrv-ls:lsn=ls4
tekelecstp 18-01-22 05:30:11 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls4 1-007-4 none 1 2 no A 4 off off off --- off
SPCA CLLI TFATCABMLQ MTPRSE ASL8 GSMSCRN
---------------- ----------- 2 --- --- off
SLSOCBIT SLSRSB RANDSLS MULTGC ITUTFR
none 1 class0 no off
IPSG GTTMODE CGGTMOD
no CdPA no
L2T PCR PCR E1 E1
LOC LINK SLC TYPE SET BPS ECM N1 N2 LOC PORT TS
1202 B 0 LIME1 11 56000 BASIC --- ----- 1202 1 5
1202 B1 1 LIME1 11 56000 BASIC --- ----- 1202 1 6
1202 B2 2 LIME1 11 56000 BASIC --- ----- 1202 1 7
1202 B3 3 LIME1 11 56000 BASIC --- ----- 1202 1 8
Link set table is (167 of 1024) 16% full.
;
This example displays the attributes of all linksets.
Note:
If the mtprse or slsocibit parameters are specified, then the output appears the same as thertrv-ls command's output.
The command filters the output to display only the linksets that have the specified
value of the parameter.
rtrv-ls
tekelecstp 08-02-26 20:11:43 EST EAGLE 38.0.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsa1111 011-001-001 none 1 1 no A 1 off off off no off
lsa1112 011-001-002 none 1 1 no A 1 off off off no off
lsa1121 011-002-001 none 1 1 no A 1 off off off no off
lsa1122 011-002-002 none 1 1 no A 1 off off off no off
lsa111111 011-011-011 none 1 1 no A 1 off off off no off
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsi311 3-001-1 none 1 2 no A 0 off off off --- off
L3T SLT GWS GWS GWS
LSN APCN24 (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsn24 024-024-024 none 1 2 no A 0 off off off --- off
Link set table is (7 of 1024) 1% full.
;
In this example:
- The TFATCABMLQ and MTPRSE fields are displayed only when a linkset is specified. The FE-PC of this link set has no CLLI; therefore the CLLI is shown as "-----------".
- The SLSOCBIT and SLSRSB fields are not displayed for ANSI linksets.
- RANDSLS information is displayed for an ANSI linkset.
rtrv-ls:lsn=ls1
tekelecstp 18-01-22 05:31:51 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls1 003-003-003 gws1 1 1 no A 15 on on on yes off
SPCA CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 7 no no
RANDSLS
off
IPSG GTTMODE CGGTMOD
no CdPA no
LP ATM
LOC LINK SLC TYPE SET BPS TSEL VCI VPI LL
1102 A 2 LIMATM 1 1.544M EXTERNAL 5 0 0
LOC LINK SLC TYPE IPLIML2
L2T PCR PCR E1 E1
LOC LINK SLC TYPE SET BPS ECM N1 N2 LOC PORT TS
1205 A 6 LIME1 1 56000 BASIC --- ----- 1205 1 1
L2T PCR PCR T1 T1
LOC LINK SLC TYPE SET BPS ECM N1 N2 LOC PORT TS
1206 A 10 LIMT1 1 56000 BASIC --- ----- 1206 1 1
Link set table is (7 of 1024) 1% full.
;
This example shows output that includes an E1 card.
rtrv-ls:lsn=ls1
tekelecstp 18-01-22 05:33:55 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls1 003-003-003 none 1 1 no A 14 off off off no off
SPCA CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 1 no no
RANDSLS
off
IPSG GTTMODE CGGTMOD
no CdPA no
LP ATM
LOC LINK SLC TYPE SET BPS TSEL VCI VPI LL
1103 A 3 LIMATM 1 1.544M EXTERNAL 5 0 0
LOC LINK SLC TYPE IPLIML2
L2T PCR PCR E1 E1
LOC LINK SLC TYPE SET BPS ECM N1 N2 LOC PORT TS
1205 A1 7 LIME1 1 56000 BASIC --- ----- 1205 1 2
Link set table is (7 of 1024) 1% full.
;
This example includes an IPLIMx to 8 Points card. The PCT feature is turned on.
rtrv-ls:lsn=ls1
tekelecstp 18-01-22 05:38:00 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls1 003-003-003 gws1 1 1 no A 15 on on on yes off
SPCA CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 1 no no
RANDSLS
off
IPSG GTTMODE CGGTMOD PCT
no CdPA no off
LP ATM
LOC PORT SLC TYPE SET BPS TSEL VCI VPI LL
1102 A 2 LIMATM 1 1.544M LINE 5 0 0
LOC PORT SLC TYPE IPLIML2
L2T PCR PCR E1 E1
LOC PORT SLC TYPE SET BPS ECM N1 N2 LOC PORT TS
1205 A 6 LIME1 1 56000 BASIC --- ----- 1205 1 1
L2T PCR PCR T1 T1
LOC PORT SLC TYPE SET BPS ECM N1 N2 LOC PORT TS
1206 A 10 LIMT1 1 56000 BASIC --- ----- 1206 1 1
Link set table is (7 of 1024) 1% full.
;
This example includes adjacent spare point codes (s-), adjacent private point codes (p-), and adjacent private and spare point codes (ps-):
rtrv-ls
tekelecstp 08-03-05 10:12:31 EST EAGLE 38.0.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsa1 001-001-002 none 1 1 no A 0 off off off no off
lsa2 p-001-002-004 none 1 1 no A 0 off off off no off
lsa3 p-001-002-005 none 1 1 no A 0 off off off no off
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsn1 s-1-002-3 none 1 2 no A 1 off off off --- off
lsn2 s-2-002-2 none 1 2 no A 1 off off off --- off
lsn3 s-2-100-1 none 1 2 no A 1 off off off --- off
lsn4 s-2-012-1 none 1 2 no A 1 off off off --- off
lsn5 2-100-1 none 1 2 no A 1 off off off --- off
lsn6 s-3-134-1 none 1 2 no A 1 off off off --- off
L3T SLT GWS GWS GWS
LSN APCN (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsn410234 ps-1-1-1-2047-aa none 1 2 no B 0 off off off --- off
lsn410235 p-1-1-1-0059-aa none 1 2 no B 0 off off off --- off
lsn4102356 ps-1-1-1-0234-aa none 1 2 no B 0 off off off --- off
Link set table is (12 of 1024) 1% full.
;
This example displays linksets using a specified adjacent point code. The MLS feature must be turned on before information can be retrieved for an adjacent point code:
rtrv-ls:apc=1-1-2
tekelecstp 07-07-26 12:49:06 EST EAGLE 37.5.0
APCA = 001-001-002
L3T SLT GWS GWS GWS
LSN SPCA SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsa1 002-002-002 none 1 1 no A 0 off off off no off
rtp4 001-002-005 none 1 1 no A 0 off off off no off
dur16 002-007-042 none 1 1 no A 0 off off off no off
morv12 012-009-005 none 1 1 no A 0 off off off no off
lsa22 004-002-022 none 1 1 no A 0 off off off no off
Link set table is (12 of 1024) 1% full.
This example displays all linksets when the MLS feature is turned on. The MLS feature allows multiple linksets to have the same adjacent point code.
rtrv-ls
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsa1 001-001-002 none 1 1 no A 0 off off off no off
lsa2 p-001-002-004 none 1 1 no A 0 off off off no off
lsa3 p-001-002-005 none 1 1 no A 0 off off off no off
rtp4 001-001-002 none 1 1 no A 0 off off off no off
dur16 001-001-002 none 1 1 no A 0 off off off no off
morv12 001-001-002 none 1 1 no A 0 off off off no off
lsa22 001-001-002 none 1 1 no A 0 off off off no off
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsn1 s-1-002-3 none 1 2 no A 1 off off off --- off
lsn2 2-100-1 none 1 2 no A 1 off off off --- off
lsn3 s-3-134-1 none 1 2 no A 1 off off off --- off
L3T SLT GWS GWS GWS
LSN APCN (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsn410234 ps-1-1-1-2047-aa none 1 2 no B 0 off off off --- off
lsn410235 p-1-1-1-0059-aa none 1 2 no B 0 off off off --- off
Link set table is (12 of 1024) 1% full.
This example displays all linksets when the Proxy Point Code feature is enabled. Proxy point codes used by the linksets are displayed:
rtrv-ls
homenetwork 08-03-19 17:03:37 EST EAGLE 38.0.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
x1 001-001-001 none 1 1 no PRX 0 off off off no off
x2 001-001-002 none 1 1 no PRX 0 off off off no off
x3 001-001-003 none 1 1 no PRX 0 off off off no off
x4 001-001-004 none 1 1 no PRX 0 off off off no off
x5 001-001-005 none 1 1 no PRX 0 off off off no off
x6 001-001-006 none 1 1 no PRX 0 off off off no off
x7 001-001-007 none 1 1 no PRX 0 off off off no off
x8 001-001-008 none 1 1 no PRX 0 off off off no off
x9 001-001-009 none 1 1 no PRX 0 off off off no off
x10 001-001-010 none 1 1 no PRX 0 off off off no off
y 002-002-002 none 1 1 no A 0 off off off no off
Link set table is (11 of 1024) 1% full.
;
This example displays linksets using a specified proxy point code:
rtrv-ls:ppc=2-2-2
homenetwork 07-05-19 17:05:04 EST EAGLE 37.5.0
PPCA = 002-002-002
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
x1 001-001-001 none 1 1 no PRX 0 off off off no off
x2 001-001-002 none 1 1 no PRX 0 off off off no off
x3 001-001-003 none 1 1 no PRX 0 off off off no off
x4 001-001-004 none 1 1 no PRX 0 off off off no off
x5 001-001-005 none 1 1 no PRX 0 off off off no off
x6 001-001-006 none 1 1 no PRX 0 off off off no off
x7 001-001-007 none 1 1 no PRX 0 off off off no off
x8 001-001-008 none 1 1 no PRX 0 off off off no off
x9 001-001-009 none 1 1 no PRX 0 off off off no off
x10 001-001-010 none 1 1 no PRX 0 off off off no off
Link set table is (11 of 1024) 1% full.
;
The following example displays all proxy linksets.
rtrv-ls:lst=prx
homenetwork 08-03-19 17:05:40 EST EAGLE 38.0.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
x1 001-001-001 none 1 1 no PRX 0 off off off no off
x2 001-001-002 none 1 1 no PRX 0 off off off no off
x3 001-001-003 none 1 1 no PRX 0 off off off no off
x4 001-001-004 none 1 1 no PRX 0 off off off no off
x5 001-001-005 none 1 1 no PRX 0 off off off no off
x6 001-001-006 none 1 1 no PRX 0 off off off no off
x7 001-001-007 none 1 1 no PRX 0 off off off no off
x8 001-001-008 none 1 1 no PRX 0 off off off no off
x9 001-001-009 none 1 1 no PRX 0 off off off no off
x10 001-001-010 none 1 1 no PRX 0 off off off no off
Link set table is (11 of 1024) 1% full.
;
This example displays information for a specified linkset when the Proxy Point Code feature is enabled:
rtrv-ls:lsn=x1
tekelecstp 18-01-22 05:39:15 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
x1 001-001-001 none 1 1 no PRX 0 on on on yes off
PPCA CLLI TFATCABMLQ MTPRSE ASL8
002-002-002 ----------- 7 --- no
RANDSLS
off
MATELSN LSUSEALM SLKUSEALM GTTMODE
---------- --- --- CdPA
Link set table is (11 of 1024) 1% full.
;
This example displays proxy linksets using a specified adjacent point code when the MLS feature is turned on and the Proxy Point Code feature is enabled:
rtrv-ls:apc=1-1-1
tekelecstp 07-03-05 17:32:59 EST EAGLE 37.5.0
APCA = 001-001-001
L3T SLT GWS GWS GWS
LSN PPCA SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
x1 002-002-002 none 1 1 no PRX 0 off off off no off
Link set table is (11 of 1024) 1% full.
;
This example displays linksets using a specified secondary point code when the MLS feature is turned on:
rtrv-ls:spc=2-2-2
homenetwork 07-05-19 17:05:04 EST EAGLE 37.5.0
SPCA = 002-002-002
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsa1 001-001-002 none 1 1 no A 0 off off off no off
lsa2 p-001-002-004 none 1 1 no A 0 off off off no off
Link set table is (12 of 1024) 1% full.
;
This example displays information for a specific linkset when the MLS feature is turned on:
rtrv-ls:lsn=lsa1
tekelecstp 18-01-22 05:40:51 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsa1 001-001-002 gws1 1 1 no A 4 on on on yes off
SPCA CLLI TFATCABMLQ MTPRSE ASL8
002-002-002 ----------- 2 --- no
RANDSLS
off
IPSG GTTMODE CGGTMOD
no CdPA no
LP ATM
LOC LINK SLC TYPE SET BPS TSEL VCI VPI LL
1102 A 2 LIMATM 1 1.544M EXTERNAL 5 0 0
LOC LINK SLC TYPE IPLIML2
L2T PCR PCR E1 E1
LOC LINK SLC TYPE SET BPS ECM N1 N2 LOC PORT TS
1205 A 6 LIME1 1 56000 BASIC ---- ------ 1205 1 1
L2T PCR PCR T1 T1
LOC LINK SLC TYPE SET BPS ECM N1 N2 LOC PORT TS
1206 A 10 LIMT1 1 56000 BASIC --- ----- 1206 1 1
Link set table is (1 of 1024) 1% full.
;
This example displays output for a specified linkset when calling party GT modification is requested:
rtrv-ls:lsn=ls3
tekelecstp 18-01-22 05:41:01 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls3 002-002-003 none 1 1 no A 0 off off off no off
SPCA CLLI TFATCABMLQ MTPRSE ASL8 GSMSCRN
---------------- ----------- 1 --- no off
RANDSLS
off
IPSG GTTMODE CGGTMOD
no AdvCdPA,CdPA,CgPA yes
Link set table is (1 of 1024) 1% full.
;
This example displays all of the linksets where calling party global title modification is requested.
rtrv-ls:cggtmod=yes
tekelecstp 08-02-27 11:56:50 EST EAGLE 38.0.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
abc14368 330-020-000 SEAS 1 1 yes a 2 off off off no off
abc34589 330-030-000 scr1 1 2 no c 3 on on on yes
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
abc32261 330-044-000 scr1 1 1 yes a 1 off off off --- off
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
Link set table is (114 of 1024) 12% full
;
This example displays output for an IPSG-M2PA linkset:
rtrv-ls:lsn=m2pa12132
tekelecstp 18-01-22 05:42:02 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
m2pa12132 001-213-002 none 1 1 no A 1 off off off no off
SPCA CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 1 no no
RANDSLS
off
IPSG GTTMODE CGGTMOD
yes CdPA no
ADAPTER RSVDSLKTPS MAXSLKTPS
m2pa 1000 5000
TPSALM LSUSEALM SLKUSEALM
maxslktps 100% 80%
LOC LINK SLC TYPE ANAME
1303 A 0 IPSG m2pa1303a
Link set table is (20 of 1024) 2% full.
;
This example displays the output for an IPSG-M3UA linkset. If value of the numslk threshold parameter is provisioned to 0, and the value is recalculated as per the provisioned links within the linkset, then an indication marker “*” is printed as a superscript to the value of the corresponding parameter.
rtrv-ls:lsn=ipsgm3ua
tekelecstp 18-01-22 05:43:50 EST EAGLE 46.6.0.0.0-71.21.00
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ipsgm3ua 008-008-004 none 1 1 no A 3 off off off no off
SPCA CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- --- --- no
RANDSLS
off
IPSG GTTMODE CGGTMOD
yes CdPA no
ADAPTER RSVDSLKTPS MAXSLKTPS
m3ua 100 100
TPSALM LSUSEALM SLKUSEALM
rsvdslktps 80% 80%
RCONTEXT ASNOTIF NUMSLKALW NUMSLKRSTR NUMSLKPROH
1234567890 yes 2* 1 1
LOC LINK SLC TYPE ANAME
1102 A2 0 IPSG ipsgm3ua1102
1202 A3 1 IPSG ipsgm3ua1202
1302 A4 2 IPSG ipsgm3ua1302
Link set table is (1 of 1024) 1% full.
;
This example displays linkset information when the ITU National and International Spare Point Code Support feature is enabled:
rtrv-ls:lsn=lsnp1
tekelecstp 18-01-22 05:44:16 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsnp1 1-002-1 none 1 2 no A 3 off off off no off
SPCI CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 2 --- ---
SLSRSB RANDSLS ITUTFR ICNIMAP OGNIMAP
1 off off itui2ituis ituis2itui
IPSG GTTMODE CGGTMOD
no CdPA no
LP ATM E1ATM
LOC LINK SLC TYPE SET BPS TSEL VCI VPI CRC4 SI SN
1104 A 0 LIME1ATM 21 2.048M LINE 5 0 ON 3 0
1105 A 1 LIME1ATM 21 2.048M LINE 5 0 ON 3 0
1106 A 2 LIME1ATM 21 2.048M LINE 5 0 ON 3 0
Link set table is (1 of 1024) 1% full.
;
This example displays output for an IPGWx linkset.
rtrv-ls:lsn=ls1315a
tekelecstp 18-01-22 05:46:00 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls1315a 000-015-000 none 1 1 no A 1 off off off no off
SPCA CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 1 no no
RANDSLS
off
IPSG GTTMODE CGGTMOD
no CdPA no
MATELSN LSUSEALM SLKUSEALM
---------- 100% 80%
LOC LINK SLC TYPE
1315 A 0 SS7IPGW
Link set table is (18 of 1024) 2% full.
;
This example displays linkset information for an ANSI linkset when the Incoming SLS Bit Rotation feature is enabled:
rtrv-ls:lsn=ls6
tekelecstp 18-01-22 05:47:41 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls06 002-007-008 scr4 1 4 no a 0 on off off no on
SPCA CLLI TFATCABMLQ MTPRSE ASL8
---------------- ls06clli 1 no no
RANDSLS
off
ISLSRSB RSLS8
1 no
IPSG GTTMODE CGGTMOD
no CdPA no
Link set table is ( 20 of 1024) 2% full
;
This example displays linkset information for an ITU linkset when the Incoming SLS Bit Rotation feature is enabled:
rtrv-ls:lsn=lsi111
tekelecstp 18-01-22 05:48:03 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsi111 1-001-1 none 1 2 no A 0 off off off no off
SPCI CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 1 --- ---
SLSOCBIT SLSRSB RANDSLS ITUTFR
none 1 off off
ISLSRSB
1
IPSG GTTMODE CGGTMOD
no CdPA no
Link set table is (1 of 1024) 1% full.
This example displays the output when information for linksets with a specified ISLSRB filter is requested:
rtrv-ls:islsrsb=4
tekelecstp 08-10-21 09:46:52 EST EAGLE 40.0.0
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsi616 6-001-6 none 1 2 no B 0 off off off no off
lsi747 7-014-7 none 1 2 no A 0 off off off no off
Link set table is (16 of 1024) 2% full.
;
This example displays linkset information for a specific linkset when the Flexible Linkset Optional Based Routing feature is turned on:
rtrv-ls:lsn=ls8
tekelecstp 18-01-22 05:49:51 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls8 001-001-001 none 1 1 no A 0 off off off no off
SPCA CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 1 --- no
RANDSLS
off
IPSG GTTMODE CGGTMOD PCT
no FLCdPA,FLCgPA no off
Link set table is (2 of 1024) 1% full.
;
This example displays linkset information for an ANSI linkset when the Incoming SLS Bit Rotation feature is enabled and the islsrsb=6 parameter was specified:
rtrv-ls:lsn=lsa
tekelecstp 18-01-22 05:49:51 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsa 001-001-001 none 1 1 no A 0 off off off no off
SPCA CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 1 --- no
RANDSLS
off
ISLSRSB RSLS8
6 yes
IPSG GTTMODE CGGTMOD
no CdPA no
Link set table is (1 of 1024) 1% full.
This example displays linkset information for an ITU link set, when the MPC, ITUDUPPC, Spare Point Code, SLSOCB and ISLSBR features are enabled:
rtrv-ls:lsn=lsi
tekelecstp 18-01-22 05:50:11 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCN (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
lsi 01001-aa none 1 2 no A 0 off off off no off
SPCN CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 1 --- ---
SLSOCBIT SLSRSB RANDSLS MULTGC ITUTFR ICNIMAP OGNIMAP
none 1 off no off none none
ISLSRSB
1
IPSG GTTMODE CGGTMOD
no CdPA no
Link set table is (4 of 1024) 1% full.
;
This example displays linkset information when all linksets are in SLT Reflect mode:
rtrv-ls
tekelecstp 11-10-13 15:55:42 EST EAGLE 44.0.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls1 001-001-001 none 1 RFT no A 0 off off off no off
ls2 002-002-002 none 1 RFT no A 0 off off off no off
ls3 003-003-003 none 1 RFT no A 0 off off off no off
Link set table is (3 of 1024) 1% full.This example displays linkset information for a specified linkset in SLT Reflect mode:
rtrv-ls:lsn=ls1
tekelecstp 18-01-22 05:51:51 EST EAGLE 46.6.0.0.0-71.21.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls1 001-001-001 none 1 RFT no A 0 off off off no off
SPCA CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 1 --- no
RANDSLS
off
IPSG GTTMODE CGGTMOD PCT
no CdPA no off
Link set table is (3 of 1024) 1% full.Example with J1 links.
rtrv-ls:lsn=ls2
tekelecstp 18-01-22 05:52:51 EST EAGLE 46.6.0.0.0-71.21.0
rtrv-ls:lsn=ls2
Command entered at terminal #4.
L3T SLT GWS GWS GWS
LSN APCN16 (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls2 001-02-03 none 1 RFT no A 3 off off off no off
SPCN16 CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- 2 --- ---
SLSRSB RANDSLS ITUTFR
1 off off
IPSG GTTMODE CGGTMOD PCT
no SysDflt no off
L2T PCR PCR J1
LOC LINK SLC TYPE SET BPS ECM N1 N2 PORT TS
1102 A 11 LIMT1 11 64000 BASIC ---- ------ 1 11
1102 A1 10 LIMT1 11 64000 BASIC ---- ------ 1 11
1102 A2 5 LIMT1 11 64000 BASIC ---- ------ 1 20
Link set table is (2 of 1024) 1% full.
;
This example displays a linkset entry with the CHGMTP3OPC parameter.
rtrv-ls:lsn=ls112
tekelecstp 18-01-22 05:55:54 EST EAGLE 46.6.0.0.0-71.21.0
rtrv-ls:lsn=ls112
Command entered at terminal #4.
L3T SLT GWS GWS GWS
LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls112 1-001-2 none 1 2 no A 0 off off off no off
SPCI CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- --- --- ---
SLSRSB RANDSLS ITUTFR
1 off off
IPSG GTTMODE CGGTMOD PCT CHGMTP3OPC
yes SysDflt no off on
ADAPTER RSVDSLKTPS MAXSLKTPS
m3ua 1000 1000
TPSALM LSUSEALM SLKUSEALM
rsvdslktps 100% 80%
RCONTEXT ASNOTIF NUMSLKALW NUMSLKRSTR NUMSLKPROH
none yes 1 1 1
Link set table is (1 of 1024) 1% full.
;
Command Executed
This example displays a linkset entry with the GNAMESET and CGPNBLSET parameter.
rtrv-ls:lsn=ls1104
Searching link set table on disk - please wait...
Command Accepted - Processing
tekelecstp 19-11-12 23:28:53 EST EAGLE 46.9.0.0.0-76.1.0
rtrv-ls:lsn=ls1104
Command entered at terminal #1.
;
tekelecstp 19-11-12 23:28:53 EST EAGLE 46.9.0.0.0-76.1.0
L3T SLT GWS GWS GWS
LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
ls1104 001-001-004 scr1 1 1 no A 1 on on on no off
SPCA CLLI TFATCABMLQ MTPRSE ASL8
---------------- ----------- --- --- no
RANDSLS
off
IPSG GTTMODE CGGTMOD PCT CHGMTP3OPC GNAMESET
yes SysDflt no off on SetA
ADAPTER RSVDSLKTPS MAXSLKTPS CGPNBLSET
m3ua 5000 5000 2
TPSALM LSUSEALM SLKUSEALM
rsvdslktps 100% 80%
RCONTEXT ASNOTIF NUMSLKALW NUMSLKRSTR NUMSLKPROH
10 yes 1 1 1
LOC LINK SLC TYPE ANAME
1104 A 0 IPSG assoc1104
Link set table is (1 of 1024) 1% full.
;Legend
- LSN—Name of the linkset. When CHINA appears after the LSN heading, each linkset that is listed under the heading was defined with the apcntype=itunchina parameter specified.
- APC/APCI/APCN/APCN24/APCN16—Adjacent DPC of the linkset
- SPC/SPCI/SPCN/SPCN24/SPCN16—Secondary PC of the linkset
- SCRN—Screen set assigned to the linkset
- L3TSET—Level 3 timer set value assigned to the linkset
- SLTSET—SLTM record associated with the linkset
- BEI—Broadcast exception indicator. Indicates whether TFP (transfer prohibited) messages can be broadcast on the linkset.
- LST—Type of links in the linkset (access links, bridge links, etc.)
- LNKS—Number of links in the linkset
- GWSA—Shows whether gateway screening is used on the specified linkset
- GWSM—Shows whether the display of messages generated for each screened message is turned on or off
- GWSD—Shows whether the gateway screening message discard function is turned on or off
- SLSCI—Shows whether the 5-to-8-bit SLS conversion feature is to be used to select links for outgoing messages directed to the given linkset
- NIS—Shows whether the Network Indicator Spare option is on or off for the specified linkset
- CLLI—The far end Common Language Location Identifier (CLLI)
- TFATCABMLQ—the minimum number of links in the given linkset (or in the combined linkset in which it resides) that must be available to user-part messages traffic in order for the STP to consider the first-choice ordered routes using that linkset as allowed rather than restricted
- MTPRSE—Shows whether the adjacent node is equipped with MTP restart
- ASL8—Shows whether the adjacent node is sending MSUs with 8-bit SLSs
- MULTGC—Shows whether multiple group codes are allowed
- MATELSN—Name of the mate IP Gateway linkset
- LSUSEALM—Percent of the linkset TPS (IPTPS) at which an alarm is generated to indicate that the actual linkset TPS is approaching the configured IPTPS value for the linkset
- SLKUSEALM—Percent of the link "fair share" TPS at which an alarm is generated to indicate that the actual link TPS is approaching the link’s "fair share" of its linkset’s configured IPTPS. The "fair share" of the linkset TPS for a link is the configured linkset TPS divided by the number of in-service links in the linkset.
- LOC—Location of the card containing the signaling links that make up the linkset
- PORT—Port on the card containing the signaling link
- SLSOCBIT—Setting of the Other CIC (Circuit Identification Code) Bit
- SLSRSB—Setting of the Rotated SLS (Signaling Link Selection) Bit
- ISLSRSB—setting of the Incoming Rotated SLS (Signaling Link Selection) Bit
- GSMSCRN—Shows whether the GSM MAP screening indicator is turned on or off
- ITUTFR—Shows whether the ITU TFR procedure indicator is turned on or off
- L2TSET—Level 2 timer set value associated with the signaling link
- SLC—Signaling link code of the signaling link
- TYPE—Type of card
- BPS—Transmission rate for the link in bits per second
- E1PORT—E1 port with the E1 interface that services the link
- E1LOC—Card location of the E1 card with the E1 interface that services the link
- T1PORT—T1 port with the T1 interface that services the link
- T1LOC—Card location of the T1 card with the T1 interface that services the link
- TS—Timeslot assigned to the link that is serviced by the E1 or T1 interface
- E1ATMCRC4—Indicator of whether CRC4 multi-frame structure is enabled or disabled
- E1ATMSI—Value of two Spare International bits of NFAS data
- E1ATMSN—Value of five Spare National bits of NFAS data
- RANDSLS—The setting of linkset for Random SLS generation
- ADAPTER—Shows whether the linkset is IPSG M2PA or IPSG M3UA linkset
- RSVDSLKTPS—Guaranteed SLKTPS for an IPSG linkset
- MAXSLKTPS—Maximum SLKTPS for an IPSG linkset
- RCONTEXT—Routing context ID of IPSG M3UA linkset
- ASNOTIF—Shows whether AS notifications will be generated for IPSG M3UA linkset
- ANAME—Association name configured for signaling link of IPSG linkset
- SLKTPS—Provisioned TPS for concerned signaling link of the specified IPSG linkset
- CGGTMOD—Shows whether calling party global title modification indicator is yes or no for the linkset
- PPC/PPCI/PPCN/PPCN24/PPCN16—The proxy point code of the linkset
- NUMSLKALW—Threshold value for IPSG M3UA linkset used to transition to Allowed state from Restricted or Prohibited state
- NUMSLKRSTR—Threshold value for IPSG M3UA linkset used to transition to Restricted state from Allowed state
- NUMSLKPROH—Threshold value for IPSG M3UA linkset used to transition to Prohibited state from Restricted or Allowed state
- ICNIMAP—Incoming NI Map
- OGNIMAP—Outgoing NI Map
- RSLS8—Shows whether the incoming SLS is rotated by 8 bits
- PCT—Shows whether the Point Code & CIC Translation (PCT) feature is applied to messages coming in or going out on links of a particular link set
- RFT—Shows whether the linkset is in SLT Reflect mode
- J1PORT—J1 port with the J1 interface that services the link
- CHGMTP3OPC—Shows whether OPC is going to be replaced by SPC.
- GNAMESET—Shows the Generic name Set.
- CGPNBLSET—Shows the Calling Party Blacklist Set.
- VISUALIZEDATA—Linkset based visualization options.
Related Topics