static-flow
The static-flow element sets preconfigured flows that allow a specific class of traffic to pass through the Oracle Communications Session Border Controller unrestricted.
Parameters
- in-realm-id
- Enter the ingress realm or interface source of packets to match for static flow translation. This in-realm-id field value must correspond to a valid identifier field entry in a realm-config. This is a required field. Entries in this field must follow the Name Format.
- description
- Provide a brief description of this static-flow configuration object.
- in-source
- Enter the incoming source IP address and port of packets to
match for static flow translation. IP address of 0.0.0.0 matches any source
address. Port 0 matches packets received on any port. The port value has no
impact on system operation if either ICMP or ALL is the selected protocol.
The in-source parameter takes the format:
in-source <ip-address>[:<port>]
- in-destination
- Enter the incoming destination IP address and port of packets
to match for static-flow translation. An IP address of 0.0.0.0 matches any
source address. Port 0 matches packets received on any port. The port value
has no impact on system operation if either ICMP or ALL is the selected
protocol. The in-destination parameter takes the format:
in-destination <ip-address>[:<port>]
- Default: 0.0.0.0
- Values: Port: Min: 0 / Max: 65535
This parameter accepts an IPv6 value.
- out-realm-id
- Enter the egress realm or interface source of packets to match for static flow translation. This out-realm-id field value must be a valid identifier for a configured realm. This required entry must follow the Name Format.
- out-source
- Enter the outgoing source IP address and port of packets to
translate to for static flow translation. IP address of 0.0.0.0 translates
to any source address. Port 0 translates to packets sent on any port. The
port value has no impact on system operation if either ICMP or ALL is the
selected protocol. The out-source parameter takes the format:
out-source <ip-address>[:<port>]
- Default: 0.0.0.0
- Values: Port: Min: 0 / Max: 65535
This parameter accepts an IPv6 value.
- out-destination
- Enter the outgoing destination IP address and port of packets to
translate to for static-flow translation. An IP address of 0.0.0.0 matches
any source address. Port 0 translates to packets sent on any port. The port
value has no impact on system operation if either ICMP or ALL is the
selected protocol. The out-destination parameter takes the format:
out-destination <ip-address>[:<port>]
- Default: 0.0.0.0
- Values: Port: Min: 0 / Max: 65535
This parameter accepts an IPv6 value.
- protocol
- Select the protocol for this static-flow. The protocol selected
must match the protocol in the IP header. The protocol remains the same for
the inbound and outbound sides of the packet flow.
- Default: UDP
- Values:
- UDP—UDP used for this static-flow element
- TCP—TCP used for this static-flow element
- ICMP—ICMP used for this static-flow element
- ALL—Static-flow element can accept flows via any of the available protocols.
- alg-type
- Select the type of NAT ALG to use
- Default: none
- Values:
- none—No dynamic ALG functionality
- NAPT—Configure as
NAPT ALG
Note:
out-source/port range overlapping with other ALG definitions is not allowed and can cause a port overlapping error during configuration verification. - TFTP—Configure as
TFTP ALG
Note:
Neither in-destination/port range overlapping or out-source/port range overlapping with other ALG definitions are allowed and can cause a port overlapping error during configuration verification.
- average-rate-limit
- This parameter is unsupported.
- start-port
- Enter the internal starting ALG ephemeral port
- Default: 0
- Values: Min: 1025 / Max: 65535
- end-port
- Enter the internal ending ALG ephemeral port
- Default: 0
- Values: Min: 1025 / Max: 65535
- flow-time-limit
- Enter the time limit for a flow, measured in seconds
- Values: Min: 0 / Max: 999999999
- initial-guard-timer
- Enter the initial flow guard timer, measured in seconds
- Values: Min: 0 / Max: 999999999
- subsq-guard-timer
- Enter the subsequent flow guard timer, measured in seconds
- Values: Min: 0 / Max: 999999999
- average-rate-limit
- Set the average rate limit of RTP flows.
- Default: 0
- Values: 0 - 125000000
Path
static-flow is an element under the media-manager path. The full path from the topmost ACLI prompt is:
Note:
This is a multiple instance configuration element.