Overview of the Oracle ZFS Storage ZS3-4 Controller

This section provides an overview of the Oracle ZFS Storage ZS3-4 controller. For installation instructions, refer to Installing an Oracle ZFS Storage ZS4-4 or Oracle ZFS Storage ZS3-4 Controller. For service instructions, refer to Servicing the Oracle ZFS Storage ZS3-4 Controller in Oracle ZFS Storage Appliance Customer Service Manual, Release OS8.8.x.

Oracle ZFS Storage ZS3-4 Electrical Specifications

The following list shows the electrical specifications for the Oracle ZFS Storage ZS3-4 controller.

Note:

The power dissipation numbers listed are the maximum rated power numbers for the power supply. The numbers are not a rating of the actual power consumption of the appliance.

Input

• Nominal frequencies: 50/60Hz

• AC operating range: 200-240 VAC

• Maximum current AC RMS: 12A @ 200 VAC

Power Dissipation

• Max power consumption: 1800 W

• Max heat output: 6143 BTU/hr

• Volt-Ampere rating: 1837 VA @ 240 VAC, 0.98 P.F.

Oracle ZFS Storage ZS3-4 Configuration Options

The Oracle ZFS Storage ZS3-4 controller can be configured as a single controller or two controllers to create a high-availability cluster configuration. The following table describes the configuration options:

CPU	Memory	Readzilla SAS-2	Boot Drive SAS-2	HBA SAS-2
4x10-core, 2.40GHz	1TB (16GB DIMMs)	Four SSDs	Two HDDs	4-port (4X4) SAS-2 6Gb/s external

Refer to https://oracle.com/zfsstorage for the most recent component specification.

Oracle ZFS Storage ZS3-4 Front Panel Components

1 Locator LED and button (white)	2 Service Required LED (amber)	3 Power/OK LED (green)
4 Power button	5 Service Processor (SP) OK LED (green)	6 Fan/CPU/Memory Service Required LED
7 Power Supply (PS) Service Required LED	8 Over Temperature Warning LED	9 USB 2.0 Connectors
10 DB-15 video connector	11 Boot drive 0 (required)	12 Boot drive 1 (required)
13 Solid state drive 2 (optional)	14 Solid state drive 3 (optional)	15 Solid state drive 4 (optional)
16 Solid state drive 5 (optional)

The Oracle ZFS Storage ZS3-4 controller has two SAS-2 system boot drives in slots 0 and 1, configured as a mirrored pair. Up to four SAS-2 read cache SSDs can fill slots 2 through 5, in order.

1 Ready to remove (blue)

2 Service action required (amber)

3 OK/Activity (green)

Oracle ZFS Storage ZS3-4 Rear Panel Components

The following graphic shows the rear panel of the Oracle ZFS Storage ZS3-4 controller. Base configuration HBAs are not depicted in this illustration.

For information about PCIe cards, see Oracle ZFS Storage ZS3-4 PCIe I/O Cards in Oracle ZFS Storage Appliance Customer Service Manual, Release OS8.8.x.

1 Power supply unit 0 status LEDs OK: green Power Supply Fail: amber AC OK: green	2 Power supply unit 0 AC inlet	3 Power supply unit 1 status LEDs OK: green Power Supply Fail: amber AC OK: green
4 Power supply unit 1 AC inlet	5 System status LEDs Power: green Attention: amber Locate: white	6 PCIe slots 0-4
7 Cluster card slot	8 Network (NET) 10/100/1000 ports: NET 0-NET 3	9 USB 2.0 ports
10 PCIe slots 5-9	11 Network management (NET MGT) 10/100 BASE-T Ethernet port	12 Serial management (SER MGT) port
13 DB-15 video connector

• Ethernet Ports - Oracle ZFS Storage ZS3-4 has four RJ-45 Gigabit Ethernet connectors (NET 0, NET 1, NET 2, NET 3) located on the motherboard that operate at 10/100/1000 Mbit/sec. These network interfaces must be configured before use.

  

• Network Management Port - The network management connector (NET MGT) is an RJ-45 10/100 BASE-T Ethernet port and provides a LAN interface to the SP console.

  

• Serial Management Port - The serial management connector (SER MGT) is an RJ-45 connector and provides a terminal connection to the SP console.

  

• HBA Ports - The 4x4 SAS-2 HBA, installed in Oracle ZFS Storage ZS3-4, provides connectivity to external Oracle Storage Drive Enclosure DE2 and Sun Disk Shelves. The HBA logical ports are numbered 3-0, top to bottom: