Remote Management > Administering ILOM (CLI) > Controlling ILOM Targets (CLI) > Performing General Tasks on ILOM Targets (CLI) |
Documentation, Support, and Training
Understanding ILOM on the Switch
Switching Between the ILOM Shell and the Linux Shell
Switch From the ILOM Shell to the Linux Shell
Switch From the Linux Shell to the ILOM Shell
Display the Date, Time, and Time Zone (CLI)
Display the Aggregate Sensor State (CLI)
Display the ILOM Sessions (CLI)
Display the ILOM Event Log (CLI)
Checking the Status of Services (CLI)
Display the HTTP Service Status (CLI)
Display the HTTPS Service Status (CLI)
Display the SSL Certificates (CLI)
Display the SNMP Service Status (CLI)
Display the SNMP Service User Accounts (CLI)
Display the SNMP Service Communities (CLI)
Display the IPMI Service Status (CLI)
Get Help on an ILOM Command (CLI)
Get Help on an ILOM Target Property (CLI)
Display the Alert Properties (CLI)
Display the ILOM User Accounts (CLI)
Display the Remote Log Hosts (CLI)
Display the Network Management Configuration (CLI)
Display the ILOM CLI Session Timeout (CLI)
Display Chassis FRU ID Information (CLI)
Display the ILOM Firmware Version (CLI)
Controlling ILOM Targets (CLI)
Performing General Tasks on ILOM Targets (CLI)
Set the Date, Time, and Time Zone (CLI)
Clear the ILOM Event Log (CLI)
Set the Remote Log Hosts (CLI)
Back Up the ILOM Configuration (CLI)
Restore the ILOM Configuration (CLI)
Performing ILOM User Tasks (CLI)
Add an ILOM User Account (CLI)
Change an ILOM User's Password and or Role (CLI)
Delete an ILOM User Account (CLI)
Disable the HTTP Service (CLI)
Enable the HTTPS Service (CLI)
Install a Custom SSL Certificate (CLI)
Remove the Custom SSL Certificate (CLI)
Disable the HTTPS Service (CLI)
Configure the SNMP Service (CLI)
Add SNMP Service User Accounts (CLI)
Modify SNMP Service User Accounts (CLI)
Delete SNMP Service User Accounts (CLI)
Add SNMP Service Communities (CLI)
Modify SNMP Service Communities (CLI)
Delete SNMP Service Communities (CLI)
Back Up SNMP Service MIBs (CLI)
Disable the SNMP Service (CLI)
Enable Alerts to Send SNMP Traps (CLI)
Enable Alerts to Send PET (CLI)
Set the ILOM CLI Session Timeout (CLI)
Upgrading the Switch Firmware Through ILOM (CLI)
Install the flint Application (CLI)
Download the Switch Firmware Package (CLI)
Set Component Firmware to Upgrade (CLI)
Upgrade the Switch Firmware (CLI)
This task enables you to configure the NET MGT interface.
Note - The following procedure makes changes that do not require a reset or reboot.
Access the ILOM CLI.
Configure the network management parameters:
-> set /SP/network property=value property=value ...
where:
property is the parameter of the network to configure.
value is the value of the property to configure.
The following properties are supported:
pendingipaddress – The value is the IP address of the CMC to be configured.
pendingipdiscovery – The value is the method of IP discovery to be configured, either static or dhcp.
pendingipgateway – The value is the IP address of the gateway to be configured.
pendingipnetmask – The value is the netmask to be configured.
Note - You can configure one, several, or all properties in one command line.
Commit to the changes:
-> set /SP/network commitpending=true
For example, to set the IP address of the CMC:
-> show /SP/network ipaddress /SP/network Properties: ipaddress = 123.45.67.89 -> set /SP/network pendingipaddress=123.45.67.90 Set ’pendingipaddress’ to ’123.45.67.90’ -> set /SP/network commitpending=true Set ’commitpending’ to ’true’
The IP address has changed to 123.45.67.90.
Note - Changing some network management properties terminates the NET MGT connection to the CMC. You must re-establish the connection to continue administering the CMC. See Access ILOM From the CLI.
Access the ILOM CLI using the new IP address.
Display the new IP address:
-> show /SP/network ipaddress /SP/network Properties: ipaddress = 123.45.67.90 ->