JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
System Administration Guide: IP Services     Oracle Solaris 11 Express 11/10
search filter icon
search icon

Document Information


Part I TCP/IP Administration

1.  Planning an IPv4 Addressing Scheme (Tasks)

2.  Planning an IPv6 Addressing Scheme (Overview)

3.  Planning an IPv6 Network (Tasks)

4.  Configuring TCP/IP Network Services and IPv4 Addressing (Tasks)

5.  Enabling IPv6 on a Network (Tasks)

6.  Administering a TCP/IP Network (Tasks)

7.  Configuring IP Tunnels

8.  Troubleshooting Network Problems (Tasks)

9.  TCP/IP and IPv4 in Depth (Reference)

10.  IPv6 in Depth (Reference)


11.  About DHCP (Overview)

12.  Planning for DHCP Service (Tasks)

13.  Configuring the DHCP Service (Tasks)

14.  Administering DHCP (Tasks)

15.  Configuring and Administering the DHCP Client

16.  Troubleshooting DHCP (Reference)

17.  DHCP Commands and Files (Reference)

Part III IP Security

18.  IP Security Architecture (Overview)

19.  Configuring IPsec (Tasks)

20.  IP Security Architecture (Reference)

21.  Internet Key Exchange (Overview)

22.  Configuring IKE (Tasks)

23.  Internet Key Exchange (Reference)

24.  IP Filter in Oracle Solaris (Overview)

25.   IP Filter (Tasks)

Part IV Networking Performance

26.  Integrated Load Balancer Overview

27.  Configuration of Integrated Load Balancer Tasks

28.  Virtual Router Redundancy Protocol (Overview)

29.  VRRP Configuration (Tasks)

30.  Implementing Congestion Control

Part V IP Quality of Service (IPQoS)

31.  Introducing IPQoS (Overview)

32.  Planning for an IPQoS-Enabled Network (Tasks)

33.  Creating the IPQoS Configuration File (Tasks)

34.  Starting and Maintaining IPQoS (Tasks)

Administering IPQoS (Task Map)

Applying an IPQoS Configuration

How to Apply a New Configuration to the IPQoS Kernel Modules

How to Ensure That the IPQoS Configuration Is Applied After Each Reboot

Enabling syslog Logging for IPQoS Messages

How to Enable Logging of IPQoS Messages During Booting

Troubleshooting with IPQoS Error Messages

35.  Using Flow Accounting and Statistics Gathering (Tasks)

36.  IPQoS in Detail (Reference)



Enabling syslog Logging for IPQoS Messages

To record IPQoS boot-time messages, you need to modify the /etc/syslog.conf file as shown in the next procedure.

How to Enable Logging of IPQoS Messages During Booting

  1. Open the /etc/syslog.conf file.
  2. Add the following text as the final entry in the file. /var/adm/messages

    Use tabs rather than spaces between the columns.

    The entry logs all boot-time messages that are generated by IPQoS into the /var/adm/messages file.

  3. Reboot the system to apply the messages.

Example 34-1 IPQoS Output From /var/adm/messages

When you view /var/adm/messages after system reboot, your output might contain IPQoS logging messages that are similar to the following.

May 14 10:44:33 ipqos-14 ipqosconf: [ID 815575]
 New configuration applied.
May 14 10:44:46 ipqos-14 ipqosconf: [ID 469457] 
Current configuration saved to init file.
May 14 10:44:55 ipqos-14 ipqosconf: [ID 435810]
Configuration flushed.

You might also see IPQoS error messages that are similar to the following in your IPQoS system's /var/adm/messages file.

May 14 10:56:47 ipqos-14 ipqosconf: [ID 123217 user.error]
 Missing/Invalid config file fmt_version.
May 14 10:58:19 ipqos-14 ipqosconf: [ID 671991 user.error] 
No ipgpc action defined.

For a description of these error messages, see Table 34-1.