JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
System Administration Guide: IP Services     Oracle Solaris 11 Express 11/10
search filter icon
search icon

Document Information

Preface

Part I TCP/IP Administration

1.  Planning an IPv4 Addressing Scheme (Tasks)

2.  Planning an IPv6 Addressing Scheme (Overview)

3.  Planning an IPv6 Network (Tasks)

4.  Configuring TCP/IP Network Services and IPv4 Addressing (Tasks)

5.  Enabling IPv6 on a Network (Tasks)

6.  Administering a TCP/IP Network (Tasks)

Major TCP/IP Administrative Tasks (Task Map)

Monitoring Network Status With the netstat Command

How to Display Statistics by Protocol

How to Display the Status of Transport Protocols

How to Display Network Interface Status

How to Display the Status of Sockets

How to Display the Status of Transmissions for Packets of a Specific Address Type

How to Display the Status of Known Routes

Probing Remote Hosts With the ping Command

How to Determine if a Remote Host Is Running

How to Determine if a Host Is Dropping Packets

Administering and Logging Network Status Displays

How to Control the Display Output of IP-Related Commands

How to Log Actions of the IPv4 Routing Daemon

How to Trace the Activities of the IPv6 Neighbor Discovery Daemon

Displaying Routing Information With the traceroute Command

How to Find Out the Route to a Remote Host

How to Trace All Routes

Monitoring Packet Transfers With the snoop Command

How to Check Packets From All Interfaces

How to Capture snoop Output Into a File

How to Check Packets Between an IPv4 Server and a Client

How to Monitor IPv6 Network Traffic

Monitoring Packets by Using IP Layer Devices

How to Check Packets on the IP Layer

Examples

Administering Default Address Selection

How to Administer the IPv6 Address Selection Policy Table

How to Modify the IPv6 Address Selection Table for the Current Session Only

7.  Configuring IP Tunnels

8.  Troubleshooting Network Problems (Tasks)

9.  TCP/IP and IPv4 in Depth (Reference)

10.  IPv6 in Depth (Reference)

Part II DHCP

11.  About DHCP (Overview)

12.  Planning for DHCP Service (Tasks)

13.  Configuring the DHCP Service (Tasks)

14.  Administering DHCP (Tasks)

15.  Configuring and Administering the DHCP Client

16.  Troubleshooting DHCP (Reference)

17.  DHCP Commands and Files (Reference)

Part III IP Security

18.  IP Security Architecture (Overview)

19.  Configuring IPsec (Tasks)

20.  IP Security Architecture (Reference)

21.  Internet Key Exchange (Overview)

22.  Configuring IKE (Tasks)

23.  Internet Key Exchange (Reference)

24.  IP Filter in Oracle Solaris (Overview)

25.   IP Filter (Tasks)

Part IV Networking Performance

26.  Integrated Load Balancer Overview

27.  Configuration of Integrated Load Balancer Tasks

28.  Virtual Router Redundancy Protocol (Overview)

29.  VRRP Configuration (Tasks)

30.  Implementing Congestion Control

Part V IP Quality of Service (IPQoS)

31.  Introducing IPQoS (Overview)

32.  Planning for an IPQoS-Enabled Network (Tasks)

33.  Creating the IPQoS Configuration File (Tasks)

34.  Starting and Maintaining IPQoS (Tasks)

35.  Using Flow Accounting and Statistics Gathering (Tasks)

36.  IPQoS in Detail (Reference)

Glossary

Index

Major TCP/IP Administrative Tasks (Task Map)

The following table lists other miscellaneous tasks to administer the network after initial configuration, such as displaying network information. The table includes a description of what each task accomplishes and the section in the current documentation where the specific steps to perform the task are detailed.

Task
Description
For Information
Display statistics on a per-protocol basis.
Monitor the performance of the network protocols on a particular system.
Display network status.
Monitor your system by displaying all sockets and routing table entries. The output includes the inet address family for IPv4 and inet6 address family for IPv6.
Display the status of network interfaces.
Monitor the performance of network interfaces, which is useful for troubleshooting transmission problems.
Display packet transmission status.
Monitor the state of packets as they are sent over the wire.
Control the display output of IPv6-related commands.
Controls the output of the ping, netstat, and traceroute commands. Creates a file that is named inet_type. Sets the DEFAULT_IP variable in this file.
Monitor network traffic.
Displays all IP packets by using the snoop command.
Trace all routes that are known to the network's routers.
Uses the traceroute command to show all routes.

Note - To monitor network interfaces, refer to Monitoring IP Interfaces and Addresses in System Administration Guide: Network Interfaces and Network Virtualization