JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
System Administration Guide: Devices and File Systems     Oracle Solaris 10 8/11 Information Library
search filter icon
search icon

Document Information

About This Book

1.  Managing Removable Media (Overview)

2.  Managing Removable Media (Tasks)

3.  Accessing Removable Media (Tasks)

4.  Writing CDs and DVDs (Tasks)

5.  Managing Devices (Overview/Tasks)

6.  Dynamically Configuring Devices (Tasks)

7.  Using USB Devices (Overview)

8.  Using USB Devices (Tasks)

9.  Using InfiniBand Devices (Overview/Tasks)

10.  Managing Disks (Overview)

11.  Administering Disks (Tasks)

12.  SPARC: Setting Up Disks (Tasks)

13.  x86: Setting Up Disks (Tasks)

14.  Configuring Oracle Solaris iSCSI Targets and Initiators (Tasks)

15.  The format Utility (Reference)

16.  Managing File Systems (Overview)

17.  Creating and Mounting File Systems (Tasks)

18.  Using The CacheFS File System (Tasks)

19.  Configuring Additional Swap Space (Tasks)

20.  Checking UFS File System Consistency (Tasks)

21.  UFS File System (Reference)

Structure of Cylinder Groups for UFS File Systems

Boot Block



Data Blocks

Free Blocks

Customizing UFS File System Parameters

Logical Block Size

Fragment Size

Minimum Free Space

Rotational Delay

Optimization Type

Number of Inodes (Files)

Maximum UFS File and File System Size

Maximum Number of UFS Subdirectories

22.  Backing Up and Restoring UFS File Systems (Overview)

23.  Backing Up UFS Files and File Systems (Tasks)

24.  Using UFS Snapshots (Tasks)

25.  Restoring UFS Files and File Systems (Tasks)

26.  UFS Backup and Restore Commands (Reference)

27.  Copying Files and File Systems (Tasks)

28.  Managing Tape Drives (Tasks)


Customizing UFS File System Parameters

Before you alter the default file system parameters that are assigned by the newfs command, you need to understand them. This section describes these parameters:

For a description of the command options that customize these parameters, see newfs(1M) and mkfs_ufs(1M).

Logical Block Size

The logical block size is the size of the blocks that the UNIX kernel uses to read or write files. The logical block size is usually different from the physical block size. The physical block size is usually 512 bytes, which is the size of the smallest block that the disk controller can read or write.

Logical block size is set to the page size of the system by default. The default logical block size is 8192 bytes (8 KB) for UFS file systems. The UFS file system supports block sizes of 4096 or 8192 bytes (4 or 8 KB). The recommended logical block size is 8 KB.

SPARC only - You can specify only the 8192-byte block size on the sun-4u platform.

To choose the best logical block size for your system, consider both the performance you want and the available space. For most UFS systems, an 8-KB file system provides the best performance, offering a good balance between disk performance and the use of space in primary memory and on disk.

As a general rule, to increase efficiency, use a larger logical block size for file systems when most of the files are very large. Use a smaller logical block size for file systems when most of the files are very small. You can use the quot -c filesystem command on a file system to display a complete report on the distribution of files by block size.

However, the page size set when the file system is created is probably the best size in most cases.

Fragment Size

As files are created or expanded, they are allocated disk space in either full logical blocks or portions of logical blocks called fragments. When disk space is needed for a file, full blocks are allocated first, and then one or more fragments of a block are allocated for the remainder. For small files, allocation begins with fragments.

The ability to allocate fragments of blocks to files, rather than just whole blocks, saves space by reducing fragmentation of disk space that results from unused holes in blocks.

You define the fragment size when you create a UFS file system. The default fragment size is 1 KB. Each block can be divided into 1, 2, 4, or 8 fragments, which results in fragment sizes from 8192 bytes to 512 bytes (for 4-KB file systems only). The lower bound is actually tied to the disk sector size, typically 512 bytes.

For multiterabyte file systems, the fragment size must be equal to the file system block size.

Note - The upper bound for the fragment is the logical block size, in which case the fragment is not a fragment at all. This configuration might be optimal for file systems with very large files when you are more concerned with speed than with space.

When choosing a fragment size, consider the trade-off between time and space: A small fragment size saves space, but requires more time to allocate. As a general rule, to increase storage efficiency, use a larger fragment size for file systems when most of the files are large. Use a smaller fragment size for file systems when most of the files are small.

Minimum Free Space

The minimum free space is the percentage of the total disk space that is held in reserve when you create the file system. The default reserve is ((64 MB/partition size) * 100), rounded down to the nearest integer and limited between 1 percent and 10 percent, inclusively.

Free space is important because file access becomes less and less efficient as a file system gets full. As long as an adequate amount of free space exists, UFS file systems operate efficiently. When a file system becomes full, using up the available user space, only root can access the reserved free space.

Commands such as df report the percentage of space that is available to users, excluding the percentage allocated as the minimum free space. When the command reports that more than 100 percent of the disk space in the file system is in use, some of the reserve has been used by root.

If you impose quotas on users, the amount of space available to them does not include the reserved free space. You can change the value of the minimum free space for an existing file system by using the tunefs command.

Rotational Delay

This parameter is obsolete. The value is always set to 0, regardless of the value you specify.

Optimization Type

The optimization type parameter is set to either space or time.

For more information, see tunefs(1M).

Number of Inodes (Files)

The number of bytes per inode specifies the density of inodes in the file system. The number is divided into the total size of the file system to determine the number of inodes to create. Once the inodes are allocated, you cannot change the number without re-creating the file system.

The default number of bytes per inode is 2048 bytes (2 KB) if the file system is less than 1 GB. If the file system is larger than 1 GB, the following formula is used:

File System Size
Number of Bytes Per Inode
Less than or equal to 1 GB
Less than 2 GB
Less than 3 GB
3 GB up to 1 TB
Greater than 1 TB or created with -T option

If you have a file system with many symbolic links, they can lower the average file size. If your file system is going to have many small files, you can give this parameter a lower value. Note, however, that having too many inodes is much better than running out of inodes. If you have too few inodes, you could reach the maximum number of files on a disk slice that is practically empty.

Maximum UFS File and File System Size

The maximum size of a UFS file system is about 16 TB of usable space, minus about one percent overhead. A sparse file can have a logical size of one terabyte. However, the actual amount of data that can be stored in a file is approximately one percent less than 1 TB because of the file system overhead.

Maximum Number of UFS Subdirectories

The maximum number of subdirectories per directory in a UFS file system is 32,767. This limit is predefined and cannot be changed.