JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
man pages section 9: DDI and DKI Driver Entry Points
search filter icon
search icon

Document Information

Preface

Introduction

Driver Entry Points

aread(9E)

attach(9E)

awrite(9E)

chpoll(9E)

close(9E)

csx_event_handler(9E)

detach(9E)

devmap(9E)

devmap_access(9E)

devmap_contextmgt(9E)

devmap_dup(9E)

devmap_map(9E)

devmap_unmap(9E)

dump(9E)

_fini(9E)

getinfo(9E)

gld(9E)

gldm_get_stats(9E)

gldm_intr(9E)

gldm_ioctl(9E)

gldm_reset(9E)

gldm_send(9E)

gldm_set_mac_addr(9E)

gldm_set_multicast(9E)

gldm_set_promiscuous(9E)

gldm_start(9E)

gldm_stop(9E)

identify(9E)

_info(9E)

_init(9E)

ioctl(9E)

ks_snapshot(9E)

ks_update(9E)

mac(9E)

mc_getcapab(9E)

mc_getprop(9E)

mc_getstat(9E)

mc_ioctl(9E)

mc_multicst(9E)

mc_propinfo(9E)

mc_setpromisc(9E)

mc_setprop(9E)

mc_start(9E)

mc_stop(9E)

mc_tx(9E)

mc_unicst(9E)

mmap(9E)

open(9E)

power(9E)

print(9E)

probe(9E)

prop_op(9E)

put(9E)

read(9E)

segmap(9E)

srv(9E)

strategy(9E)

tran_abort(9E)

tran_bus_reset(9E)

tran_destroy_pkt(9E)

tran_dmafree(9E)

tran_getcap(9E)

tran_init_pkt(9E)

tran_quiesce(9E)

tran_reset(9E)

tran_reset_notify(9E)

tran_setcap(9E)

tran_start(9E)

tran_sync_pkt(9E)

tran_tgt_free(9E)

tran_tgt_init(9E)

tran_tgt_probe(9E)

tran_unquiesce(9E)

write(9E)

tran_abort

- abort a SCSI command

Synopsis

#include <sys/scsi/scsi.h> 



 int prefixtran_abort(struct scsi_address *ap, struct scsi_pkt *pkt);

Interface Level

Solaris architecture specific (Solaris DDI).

ARGUMENTS

ap

Pointer to a scsi_address(9S) structure.

pkt

Pointer to a scsi_pkt(9S) structure.

Description

The tran_abort() vector in the scsi_hba_tran(9S) structure must be initialized during the HBA driver's attach(9E) to point to an HBA entry point to be called when a target driver calls scsi_abort(9F).

tran_abort() should attempt to abort the command pkt that has been transported to the HBA. If pkt is NULL, the HBA driver should attempt to abort all outstanding packets for the target/logical unit addressed by ap.

Depending on the state of a particular command in the transport layer, the HBA driver may not be able to abort the command.

While the abort is taking place, packets issued to the transported layer may or may not be aborted.

For each packet successfully aborted, tran_abort() must set the pkt_reason to CMD_ABORTED, and pkt_statistics must be OR'ed with STAT_ABORTED .

Return Values

tran_abort() must return:

1

upon success or partial success.

0

upon failure.

See Also

attach(9E), scsi_abort(9F), scsi_hba_attach(9F), scsi_address(9S), scsi_hba_tran(9S), scsi_pkt(9S)

Writing Device Drivers

Notes

If pkt_reason already indicates that an earlier error had occurred, tran_abort() should not overwrite pkt_reason with CMD_ABORTED.