Sun Fire 6800/4810/4800/3800 Systems Platform Administration Manual
Firmware Release 5.15.0
817-0999-10
Contents |
System Controller Logical Connection Limits
System Controller Tasks Completed at System Power-On
To Set Up or Reconfigure the Domains in Your System
To Set Up Domains With Component Redundancy in a Sun Fire 6800 System
Reliability, Availability, and Serviceability (RAS)
System Controller Clock Failover
System Controller Failover Recovery
Error Diagnosis and Domain Recovery
Unattended Power Failure Recovery
System Controller Reboot Recovery
System Controller Error Logging
Dynamic Reconfiguration Software
IP Multipathing (IPMP) Software
Sun Management Center Software for the Sun Fire 6800/4810/4800/3800 Systems
2. System Controller Navigation Procedures
Connection to the System Controller
To Obtain the Platform Shell Using telnet
To Initiate a Serial Connection With tip
To Obtain the Platform Shell Using the Serial Port
Obtaining a Domain Shell or Console
To Obtain the Domain Shell Using telnet
To Obtain the Domain Shell From the Domain Console
To Enter the Domain Console From the Domain Shell If the Domain Is Inactive
To Enter the Domain Shell From the Domain Console
To Get Back to the Domain Console From the Domain Shell
To Enter a Domain From the Platform Shell
To Terminate an Ethernet Connection With telnet
To Terminate a Serial Connection With tip
To Install and Cable the Hardware
To Set Up Additional Services Before System Power On
To Set the Date and Time for the Platform
To Set a Password for the Platform
To Configure Platform Parameters
To Set the Date and Time for Domain A
To Set a Password for Domain A
To Configure Domain-Specific Parameters
Saving the Current Configuration to a Server
To Use dumpconfig to Save Platform and Domain Configurations
Installing and Booting the Solaris Operating Environment
To Install and Boot the Solaris Operating Environment
4. Creating and Starting Multiple Domains
To Create a Third Domain on a Sun Fire 6800 System
setupplatform and setupdomain Parameter Settings
Setting and Changing Passwords for the Platform and the Domain
Solaris Operating Environment Security
Powering Off and On the System
Assigning and Unassigning Boards
To Unassign a Board From a Domain
Swapping Domain HostID/MAC Addresses
To Swap the HostID/MAC Address Between Two Domains
To Restore the HostID/MAC Address Swapped Between Domains
Saving and Restoring Configurations
Using the restoreconfig Command
7. Diagnosis and Domain Restoration
Diagnosis and Domain Restoration Overview
Auto-Diagnosis and Auto-Restoration
Automatic Recovery of Hung Domains
Obtaining Auto-Diagnosis and Domain Restoration Information
Reviewing Auto-Diagnosis Event Messages
Reviewing Additional Error Information
What Triggers an Automatic Failover
What Happens During a Failover
Conditions That Affect Your SC Failover Configuration
To Perform a Manual SC Failover
To Obtain Failover Status Information
Recovering After an SC Failover
To Recover After an SC Failover Occurs
Capturing and Collecting System Information
Platform, Domain, and System Messages
Platform and Domain Status Information From System Controller Commands
Diagnostic and System Configuration Information From Solaris Operating Environment Commands
Recovering from a Repeater Board Failure
To Obtain and Add a COD RTU License Key to the COD License Database
To Delete a COD License Key From the COD License Database
To Review COD License Information
To Enable Instant Access CPUs and Reserve Domain RTU Licenses
To Identify COD CPU/Memory Boards
To View COD Usage by Resource and Domain
12. Removing and Replacing Boards
CPU/Memory Boards and I/O Assemblies
To Remove and Replace a System Board
To Unassign a Board From a Domain or Disable a System Board
To Hot-Swap a CPU/Memory Board Using DR
To Hot-Swap an I/O Assembly Using DR
To Remove and Replace a PCI Card
To Remove and Replace a CompactPCI Card
To Remove and Replace a Repeater Board
To Remove and Replace the System Controller Board in a Single SC Configuration
To Remove and Replace a System Controller Board in a Redundant SC Configuration
To Remove and Replace ID Board and Centerplane
To Determine an I/O Physical Slot Number Using an I/O Device Path
B. Setting Up an HTTP or FTP Server: Examples
Copyright © 2003, Sun Microsystems, Inc. All rights reserved.