⯿†v¯á--˘Sw˜8Șñ˘S-Fo˚Ä˚É E˜8¸áÈ<â
¯¿ùı¯W-éºë˜ ˜ã ÚØDSã/Un@` .Uúåé -TI=Ü˚& ¯ufi¸ 趆¬Î¿ ‘≥Ùfi¿ã˜ ˜)
˚ùåé ?˚;t˚y<⯿˜:ú·¯Èûåé ˜R˜ÿ-òãôåòã üåé «ÛÄ˚:LT1˚ã{‰àÕ 0ë:†:Ÿb y~øã ˜G’˜˜ãÈZªG° ç†åé ±óøã ˆ:Ÿ˚˚Ma˚ $·èºìÒ˜ ã Ù§Fa3IpGûåé |ã{å|å <⧯¿†v˜?˘Sw˜«„¯Ü˜?-$¯B˚¸R5˜«˚?„˜?1¯-ç˚”˚v<â´¯¿¯Èx¯
¯Ó·˜%¯Ó-˜æ·¸
Sun SPARC Enterprise M4000/M5000 Servers Product Notes for XCP Version 1041
|
![Table Of Contents Table Of Contents](shared/toc01.gif) ![Previous Chapter Previous Chapter](shared/prev01.gif) ![NoNext NoNext](shared/next02.gif) ![NoIndex NoIndex](shared/index02.gif) |
Sun SPARC Enterprise M4000/M5000 Servers Product Notes
|
This document includes these sections:
Supported Firmware and Software Versions
The following firmware and software versions are supported in this release:
- XSCF Control Package (XCP) 1041 or later is preinstalled in your server.
- The first version of the Solaris
Operating System (OS) to support these servers is the Solaris 10 11/06 OS.
- These servers also support Solaris 10 8/07 OS.
|
Caution - CR ID 6534471: The system may panic or trap during a normal operation. This bug has been fixed in Solaris 10 8/07. For systems running Solaris 10 11/06, you can upgrade to Solaris 10 8/07 or apply patch 120011-08. This CR is listed in the section, Solaris Issues and Workarounds.
|
- XCP 1041 supports the Sun External I/O Expansion Unit.
- This XCP release does not support the Capacity-On-Demand (COD) feature.
Note - It is required that all SPARC Enterprise M4000/M5000 servers be upgraded to XCP 1050 in order to support adding future COD Right To Use (RTU) licenses. Contact your local Service Representative for assistance.
|
If you plan to boot your SPARC Enterprise M4000/M5000 server from a Solaris WAN boot server on the network, you must upgrade the wanboot executable. See Booting From a WAN Boot Server for details.
Note - For the latest information on supported firmware and software versions, see Software Resources.
|
Solaris Patch Information
The following patches are mandatory for Sun SPARC Enterprise M4000/M5000 servers running Solaris 10 11/06 OS. These patches are not required for servers running Solaris 10 8/07 OS.
Note - Each patch ID listed below includes a revision level, shown as a two-digit suffix. Check SunSolve.Sun.COM for the latest patch revision. See Software Resources for information on how to find the latest patches.
|
Install the patches in the following order:
After installing patch 118833-36, reboot your domain before proceeding.
Install version 125100-08 at minimum. See the 125100-08 README file for a list of other patch requirements.
- 123839-07
- 120068-03
- 125424-01
- 118918-24
- 120222-21
- 125127-01
After installing patch 125127-01, reboot your domain before proceeding.
Known Issues
This section describes known hardware and software issues in this release.
General Functionality Issues and Limitations
- The XSCF web browser interface, also known as the browser user interface (BUI), has limited availability in this release. It can be used for importing the XSCF firmware and it supports the snapshot Full log set collection function. Use the command-line interface (CLI) instead on the Service Processor and the domains for other activities.
- For 1027A-Z/X1027A-Z, PCIe Dual 10 Gigabit Ethernet Fiber XFP cards, these limits apply:
- Do not use more than two cards per domain.
- Do not use these cards in an External I/O Expansion Unit.
- For 4447A-Z/X4447A-Z, PCIe Quad-port Gigabit Ethernet Adapter UTP cards, these maximum limits apply:
- No more than two cards per I/O boat
- No more than four cards in a Sun SPARC Enterprise M4000 server
- No more than eight cards in a Sun SPARC Enterprise M5000 server
- You cannot use the following user account names, as they are reserved by the XSCF firmware for system use: root, bin, daemon, adm, operator, nobody, sshd, rpc, rpcuser, ldap, apache, ntp, admin, and default.
Hardware Installation and Service Issues
This section describes hardware-specific issues and workarounds.
Specific Issues and Workarounds
TABLE 1 lists known issues for which a defect change request ID has been assigned. The table also lists possible workarounds.
TABLE 1 Hardware Issues and Workarounds
CR ID
|
Description
|
Workaround
|
6433420
|
The domain console might display a Mailbox timeout or IOCB interrupt timeout error during boot.
|
Issue a reset-all command from the OBP (OK) prompt and reboot.
|
6488846
|
During boot, the domain console might display a checksum error for the SG(X)PCI2SCSIU320-Z SCSI controller I/O card.
|
Check for the availability of the latest controller card firmware.
|
6498780
|
On the Sun SPARC Enterprise M4000/M5000 servers, the OpenBoot PROM (OBP) might not detect the on-board disk (HDD) boot device. Performing a boot disk results in a console message:
Can’t locate boot device
|
The PCI or PCI-X plug-in adapter card might not be seated correctly. Reseat the card in slot 0 of the IOU.
|
U320 PCIe SCSI Card
U320 PCIe SCSI card, part numbers 375-3357-01/02, is not supported in PCI cassettes for SPARC Enterprise M4000/M5000 servers. Customers must use
375-3357-03 or later.
DIMM Replacement
The DIMMs are cold FRU replacement components. The entire server must be powered off and the power cords disconnected to replace the DIMMs.
You can mount up to 4 memory boards on the SPARC Enterprise M4000 server and up to 8 memory boards on the SPARC Enterprise M5000 server. The DIMMs on the memory board are grouped into group A and group B.
Here are the DIMM mount conditions:
DIMM mounting rules:
- Four(4) DIMMs per group can be mounted.
- Capacity of the DIMMs in group A must be equal to or larger than the capacity of the DIMMs in group B.
- The capacity of the DIMMs in group B must be equal to or less than the capacity of the DIMMs in group A. DIMMs in group B are optional.
- For both groups, DIMMs must be of the same capacity and rank within a group. DIMMs of different capacity cannot be mixed in a group.
Installing the PCI Cassette
The following changes belong in the Sun SPARC Enterprise M4000/M5000 Servers Service Manual.
|
Caution - Do not forcethe PCI cassette into a slot. Doing so can cause damage to the cassette and server.
|
1. Align the PCI cassette on the gray plastic guide and install it into the slot.
2. Lock the lever into place to seat the cassette.
Note - As the lever is moved pressure will build up, then just prior to locking into place the pressure will suddenly release. If the lever locks in place without the pressure release, the card may not be seated correctly. If this happens remove and reinstall the card.
|
Note - When you insert the PCI cassette using hot-swap, the cassette is automatically powered on and configured. Check that the power LED on the cassette is lit to be certain the cassette is correctly seated.
|
3. Connect all cables to the PCI cassette and reconnect the cable management arm if necessary.
Attaching End Caps to the Rails
The following information belongs in the Sun SPARC Enterprise Equipment Rack Mounting Guide.
After securing the cable management arm (CMA) to the Sun SPARC Enterprise M4000/M5000 server, attach the provided end caps to the rails.
1. Secure the CMA to the server.
Refer to the Sun SPARC Enterprise Equipment Rack Mounting Guide for information on installing the CMA to the server.
2. Attach the end caps onto the slide rails.
- For the Sun SPARC Enterprise M4000 server, an end cap is attached to both the right and left rear rails (FIGURE 1).
- For the Sun SPARC Enterprise M5000 server, both end caps are attached to the rails on the same side to which the CMA is not attached (FIGURE 2).
Note - If the CMA is not used, attach all end caps to the rails of the server. The SPARC Enterprise M4000 server uses two end caps. The SPARC Enterprise M5000 server uses four end caps.
|
FIGURE 1 End Caps on the Sun SPARC Enterprise M4000 Slide Rails
FIGURE 2 End Caps on the Left Rear of the Sun SPARC Enterprise M5000 Slide Rails
3. Connect the power cables to the rear of the server and secure them with the cable retention clamps.
|
Caution - Do not connect the power cables to a power source at this time.
|
4. Run the power cables beneath the CMA and secure them in place with tie wraps.
The power cables and infiniband cables should hang loosely in a service loop behind the server or the CMA might not be able to fully retract.
5. Ensure that the server can slide in and out of the equipment rack without dislodging the power cables.
FIGURE 3 and FIGURE 4 shows how the CMA extends and retracts.
FIGURE 3 CMA Extended and Retracted on the Sun SPARC Enterprise M4000 Server
FIGURE 4 CMA Extended and Retracted on the Sun SPARC Enterprise M5000 Server
6. Slide the server into the equipment rack.
7. Tighten the four (4) captive screws at the front of the server to secure the server in the equipment rack.
8. Replace the rack stabilizer to its original position.
Installing the Bracket Kit (Optional)
If additional attachment points are required to route the cables, the bracket kit can be installed. The bracket kit includes the following:
- Two (2) brackets
- Four (4) m5 screws
- Four (4) cage nuts
- 14 velcro strips
These brackets can be used with or without the CMA for the Sun SPARC Enterprise M4000/M5000 servers.
1. Extend the rack stabilizer.
2. Slide the server out of the rack several inches for access to the rear of the Sun Rack.
3. Position the cage nuts behind the threaded ears of the Sun Rack and insert the two (2) screws through the bracket and rack ear (FIGURE 5).
Brackets should be positioned near the top level of the server or slightly below it.
Note - Brackets can be installed one per side, one only (right or left side), or two on one side, as desired for convenience in cable management.
|
4. Twist the cage nuts onto the screws from behind the rack ears.
The flat edges of the cage nuts should be aligned with the rack post to prevent the server from scraping against it.
FIGURE 5 Installing the Bracket Kit in a Sun Rack 1000
5. Insert velcro strips in the desired slots of the bracket to hold back cables.
Built-in cut-outs along the sides of the Sun Rack can also be used to insert velcro strips to hold back cables, as desired.
6. Slide the server into the equipment rack.
7. Replace the rack stabilizer to its original position.
Power Wiring Configurations
To ensure redundant power sourcing, use the provided wiring configurations for the Sun SPARC Enterprise M4000/M5000 servers in a Sun Rack 1000 38/42.
The Sun Rack 1000-38/42 can fit up to two modular power supply (MPS). Each MPS is two rack units tall. The MPS must always be installed into the bottom of the rack.
Note - The numbering in a Sun Rack reads from bottom to top and right to left.
|
TABLE 2 Wiring Connections for Six M4000 Servers with One 60A 3phase MPS
Server
|
M4000 PSU_1
|
M4000 PSU_0
|
M4000_5
|
MPS_0-A5
|
MPS_0-B5
|
M4000_4
|
MPS_0-A4
|
MPS_0-B4
|
M4000_3
|
MPS_0-A3
|
MPS_0-B3
|
M4000_2
|
MPS_0-A2
|
MPS_0-B2
|
M4000_1
|
MPS_0-A1
|
MPS_0-B1
|
M4000_0
|
MPS_0-A0
|
MPS_0-B0
|
TABLE 3 Wiring Connections for Six M4000 Servers with Two 30A 3phase MPS
Server
|
M4000 PSU_1
|
M4000 PSU_0
|
M4000_5
|
MPS_1-B5
|
MPS_1-A5
|
M4000_4
|
MPS_0-B4
|
MPS_0-A4
|
M4000_3
|
MPS_1-B3
|
MPS_1-A3
|
M4000_2
|
MPS_0-B2
|
MPS_0-A2
|
M4000_1
|
MPS_1-B1
|
MPS_1-A1
|
M4000_0
|
MPS_0-B0
|
MPS_0-A0
|
FIGURE 6 The Sun Rack 1000 With Six SPARC Enterprise M4000 Servers and One MPS
Note - The numbering in a Sun Rack reads from bottom to top and right to left.
|
TABLE 4 Wiring Connections for Three M5000 Servers with One 60A 3phase MPS
Server
|
M5000 PSU_3
|
M5000 PSU_2
|
M5000 PSU_1
|
M5000 PSU_0
|
M5000_2
|
MPS_0-B5
|
MPS_0-A5
|
MPS_0-B4
|
MPS_0-A4
|
M5000_1
|
MPS_0-B3
|
MPS_0-A3
|
MPS_0-B2
|
MPS_0-A2
|
M5000_0
|
MPS_0-B1
|
MPS_0-A1
|
MPS_0-B0
|
MPS_0-A0
|
TABLE 5 Wiring Connections for Three M5000 Servers with Two 30A 3phase MPS
Server
|
M5000 PSU_3
|
M5000 PSU_2
|
M5000 PSU_1
|
M5000 PSU_0
|
M5000_2
|
MPS_1-B2
|
MPS_1-A2
|
MPS_0-B2
|
MPS_0-A2
|
M5000_1
|
MPS_1-B1
|
MPS_1-A1
|
MPS_0-B1
|
MPS_0-A1
|
M5000_0
|
MPS_1-B0
|
MPS_1-A0
|
MPS_0-B0
|
MPS_0-A0
|
FIGURE 7 The Sun Rack 1000 With Three SPARC Enterprise M5000 Servers and Two MPS
Electrical Specifications
The following changes belong in the SPARC Enterprise M4000/M5000 Servers Site Planning Guide and the SPARC Enterprise M4000/M5000 Servers Service Manual.
TABLE 6 Midrange Servers Electrical Specifications
|
SPARC Enterprise M4000
|
SPARC Enterprise M5000
|
Maximum current
|
24.0A at 100-127 VAC (12A/cord)
12.0A at 200-240 VAC (12A/cord)
|
48A at 100-127 VAC (12A/cord)
24A at 200-240 VAC (12A/cord)
|
Input voltage
|
100-127 VAC
200-240 VAC
|
100-127 VAC
200-240 VAC
|
Plug type
|
IEC 60320 C20
IEC 60309 16A 250V (All other locations except Japan, Korea, and Taiwan)
NEMA L5-15 125V 15A (Americas and Taiwan)
NEMA L6-20 250V 20A (Americas, Japan, Korea, and Taiwan)
|
IEC 60320 C20
IEC 60309 16A 250V (All other locations except Japan, Korea, Taiwan)
NEMA L5-15 125V 15A (Americas and Taiwan)
NEMA L6-20 250V 20A, Americas, Japan, Korea, and Taiwan)
|
Hardware Documentation Updates
This section contains late-breaking hardware information that became known after the documentation set was published.
TABLE 7 lists known documentation updates.
TABLE 7 Hardware Documentation Updates
Title
|
Page Number
|
Update
|
All SPARC Enterprise M4000/M5000 servers documentation
|
|
All DVD references are now referred to as CD-RW/DVD-RW.
|
|
|
Updated glossary terms:
External I/O Expansion Unit -- A rack mountable device to add on PCI slots. It is connected to the system’s I/O unit through the PCIe connection and contains one or two I/O boats.
I/O boat -- An I/O unit in the External I/O Expansion Unit. The I/O boat connects to a PCI-Express (PCIe) slot through a PCIe switch or a PCI-X bridge on the I/O boat and offers either six PCI-X slots or six PCIe slots.
|
Sun SPARC Enterprise M4000/M5000 Servers Site Planning Guide
|
1-7
|
TABLE 1-3 “Midrange Servers Physical Specifications“
Correct numerical value of “Depth” is 810mm/31.9 in. for the SPARC Enterprise M4000/M5000 servers.
|
|
2-4
|
TABLE 2-2 “Midrange Servers Electrical Specifications“
See Electrical Specifications for the changes.
|
Sun SPARC Enterprise M4000/M5000 Servers Service Manual
|
8-6
|
8.1.3, “Installing the PCI Cassette”
See Installing the PCI Cassette for the changes.
|
|
11-7
|
11.2, “DIMM Replacement”
See DIMM Replacement for the changes.
|
|
C-7
|
TABLE C-5 “Power Supply Feature”
See Electrical Specifications for the changes.
|
Sun SPARC Enterprise M4000/M5000 Servers Installation Manual
|
8-3
|
3.3, “Connecting the Administration Console”.
The RJ-11 connector at the top of Figure 3-1 was not labelled. The RJ-11 connector is not for connection to TNV circuits. Do not use this connector.
|
SPARC Enterprise M8000/M9000 Servers Overview Guide
|
Page 1-8
|
In Table 1-1, “Main Unit Specification”
The following information will be added.
Architecture: SPARCV9 architecture
Platform groups: sun4u
Platform names: SunW, SPARC-Enterprise
|
Software and Firmware Issues
This section describes specific software and firmware issues and workarounds.
XCP Issues and Workarounds
TABLE 8 lists known XCP issues and possible workarounds.
TABLE 8 XCP Issues and Workarounds
CR ID
|
Description
|
Workaround
|
6486286
|
Domain console connection does not cancel shell when disconnected.
|
Always log out of the Solaris OS before exiting the console connection.
If you accidentally disconnect the domain console without logging out:
- Log in again to the domain console
- Log out
- Exit the console connection
|
6519877
|
All domains must be powered off before upgrading the XCP firmware.
|
Power off domains before using the flashupdate command to upgrade XCP firmware.
|
6521896
|
If you log in to the XSCF Unit while it is still booting, you may get a bash$ prompt instead of the XSCF> prompt, and be unable to perform most operations.
|
Log out of the bash$ prompt and wait for the XSCF Unit to finish booting.
|
6529635
|
The showdomainstatus -a command shows domain status as Powered Off, but the showboards -a command shows the domain is testing.
|
Use the showboards command to check the status of domain power.
The showdomainstatus command takes a longer time to show the correct status.
|
6532036
|
Some commands that update configuration data take a relatively long time to execute.
|
Do not cancel set* commands. They appear to hang, but eventually complete in about 30 seconds.
|
6533158
|
The fault (memory.block.ue) is encountered and reported periodically
|
An uncorrectable error exists in a DIMM and the DIMM should be replaced.
|
6537345
|
When using the XSCF Web to import a firmware image, if the image is corrupted, the flashupdate command might later report an internal error.
|
Import a firmware image again. Reboot the XSCF Unit, then use the flashupdate command again to clear the internal error.
|
6538564
|
Using the rebootxscf command might result in a process down error, and possibly an FMA event with MSG ID SCF-8005-NE
|
There is no workaround. Check for the availability of a patch for this defect.
|
6543260
|
The showaudit all command shows a long list of defaults in the policy section after the database is cleared.
|
To clear the non-existent user default settings, run the following commands:
setaudit -a opl=enable
setaudit -a opl=default
|
6565422
|
The Latest communication field in showarchiving is not updated regularly.
|
Disabling and re-enabling archiving refreshes the Latest communication field in showarchiving output.
|
6573729
|
When the snapshot CLI attempts to write to a USB stick that has write protect set results in an I/O error.
|
Do not attempt to use write-protected USB devices for collecting snapshot.
|
6577801
|
An incorrect domain state is reported. After the command sendbreak to domain is issued, showdomainstatus continues to show the state as ‘Running’ when the domain is actually at ’ok’ prompt.
|
There is no workaround. This is the side affect of the sendbreak operation.
|
6595501
|
If an invalid SMTP server is configured, a subsequent attempt to disable email service (using the setemailreport CLI) may block for up to 30 minutes.
|
Wait for the CLI to complete. The rest of the system will function normally during this time.
- The CLI can also be aborted by ^C. Note that the operation (disabling emailreport) is completed, even if ^C is used.
- showemailreport can be used to confirm that the service has been disabled.
|
Solaris Issues and Workarounds
TABLE 9 lists Solaris issues and possible workarounds.
TABLE 9 Solaris Issues and Workarounds
CR ID
|
Description
|
Workaround
|
6348554
|
Using the cfgadm -c disconnect command on the following cards might hang the command:
- SG-XPCIE2FC-QF4 Sun StorageTek Enterprise Class 4Gb Dual-Port Fibre Channel PCI-E HBA
- SG-XPCIE1FC-QF4 Sun StorageTek Enterprise Class 4Gb Single-Port Fibre Channel PCI-E HBA
- SG-XPCI2FC-QF4 Sun StorageTek Enterprise Class 4Gb Dual-Port Fibre Channel PCI-X HBA
- SG-XPCI1FC-QF4 Sun StorageTek Enterprise Class 4Gb Single-Port Fibre Channel PCI-X HBA
|
Do not perform cfgadm -c disconnect operation on the affected cards.
|
6459540
|
The DAT72 internal tape drive might time out during tape operations.
The device might also be identified by the system as a QIC drive.
|
Add the following definition to /kernel/drv/st.conf:
tape-config-list=
"SEAGATE DAT DAT72-000",
"SEAGATE_DAT____DAT72-000",
"SEAGATE_DAT____DAT72-000";
SEAGATE_DAT____DAT72-000=1,0x34,0,0x9639,4,0x00,0x8c,0x8c,
0x8c,3;
There are four spaces between “SEAGATE DAT and DAT72-000.
|
6472153
|
If you create a Solaris Flash archive on a non-SPARC Enterprise M4000/M5000 sun4u server and install it on a SPARC Enterprise M4000/M5000 sun4u server, the console’s TTY flags will not be set correctly. This can cause the console to lose characters during stress.
|
Just after installing Solaris OS from a Solaris Flash archive, telnet into the SPARC Enterprise M4000/M5000 server to reset the console’s TTY flags as follows:
# sttydefs -r console
# sttydefs -a console -i "9600 hupcl opost onlcr crtscts" -f "9600"
This procedure is required only once.
|
6495303
|
The use of a PCIe Dual-Port Ultra320 SCSI controller card (SG-(X)PCIE2SCSIU320Z) in IOU Slot 1 on a SPARC Enterprise M4000/M5000 server may result in a system panic.
|
Do not use this card in IOU Slot 1 on a SPARC Enterprise M4000/M5000 server.
This bug has been fixed in Solaris 10 8/07.
|
6498283
|
Using the DR deleteboard command while psradm operations are running on a domain might cause a system panic.
|
There is no workaround. Check for the availability of a patch for this defect.
This bug has been fixed in Solaris 10 8/07.
|
6508432
|
A large number of spurious PCIe correctable errors can be recorded in the FMA error log.
|
To mask these errors, add the following entry to the /etc/system file and then reboot the system:
set pcie:pcie_aer_ce_mask = 0x2001
This bug has been fixed in Solaris 10 8/07.
|
6522017
|
Domains using the ZFS file system cannot use DR.
|
Set the maximum size of the ZFS ARC lower. For detailed assistance please contact Sun Service.
|
6530178
|
DR addboard command can hang. Once problem is observed, further DR operations are blocked. Recovery requires reboot of the domain.
|
There is no workaround. Check for the availability of a patch for this defect.
This bug has been fixed in Solaris 10 8/07.
|
6531036
|
The error message network initialization failed can appear repeatedly after boot net installation.
|
There is no workaround.
|
6534471
|
Systems may panic/trap during normal operation.
|
Make sure you have the correct /etc/system parameter:
set heaplp_use_stlb=0
This bug has been fixed in Solaris 10 8/07.
|
6539909
|
Do not use the following I/O cards for network access when you are using the boot net install command to install the Solaris OS:
- X4447A-Z/X4447A-Z, PCIe Quad-port Gigabit Ethernet Adapter UTP
- X1027A-Z/X1027A-Z, PCIe Dual 10 Gigabit Ethernet Fiber XFP
|
When running Solaris 10 11/06, use an alternate type of network card or onboard network device to install the Solaris OS via the network.
This defect does not exist in Solaris 10 8/07.
|
6542632
|
Memory leak in PCIe module if driver attach fails.
|
There is no workaround. Check for the availability of a patch for this defect.
This bug has been fixed in Solaris 10 8/07.
|
6545685
|
If the system has detected Correctible Memory Errors (CE) at power-on self-test (POST), the domains might incorrectly degrade 4 or 8 DIMMs.
|
Increase the memory patrol timeout values used via the following setting in /etc/system:
set mc-opl:mc_max_rewrite_loop = 20000
|
6546188
|
The system panics when running hotplug (cfgadm) and DR operations (addboard and deleteboard)on:
- X4447A-Z, PCI-e Quad-port Gigabit Ethernet Adapter UTP
- X1027A-Z1, PCI-e Dual 10 Gigabit Ethernet Fiber XFP Low profile Adapter
|
There is no workaround. Check for the availability of a patch for this defect.
|
6551356
|
The system panics when running hotplug (cfgadm) to configure a previously unconfigured card. The message "WARNING: PCI Expansion ROM is not accessible" will be seen on the console shortly before the system panic. The following cards are affected by this defect:
- X4447A-Z, PCI-e Quad-port Gigabit Ethernet Adapter UTP
- X1027A-Z1, PCI-e Dual 10 Gigabit Ethernet Fiber XFP Low profile Adapter
|
Perform cfgadm -c disconnect to completely remove the card. After waiting at least 10 seconds, the card may be configured back into the domain using the cfgadm -c configure command.
|
6556742
|
The system panics when DiskSuite can not read the metadb during DR. This bug affects the following cards:
- SG-XPCIE2FC-QF4, 4Gb PCI-e Dual-Port Fibre Channel HBA
- SG-XPCIE1FC-QF4, 4Gb PCI-e Single-Port Fibre Channel HBA
- SG-XPCI2FC-QF4, 4Gb PCI-X Dual-Port Fibre Channel HBA
- SG-XPCI1FC-QF4, 4Gb PCI-X Single-Port Fibre Channel HBA
|
Panic can be avoided when a duplicated copy of the metadb is accessible via another Host Bus Adaptor. Or you can apply patch
125166-06.
|
6559504
|
Messages of the form "nxge: NOTICE: nxge_ipp_eccue_valid_check: rd_ptr = nnn wr_ptr = nnn" will be observed on the console.
|
These messages can be safely ignored.
|
6563785
|
Hot-plug operation with the following cards might fail if a card is disconnected and then immediately reconnected:
- SG-XPCIE2SCSIU320Z Sun StorageTek PCI-E Dual-Port Ultra320 SCSI HBA
- SGXPCI2SCSILM320-Z Sun StorageTek PCI Dual-Port Ultra320 SCSI HBA
|
After disconnecting a card, wait for a few seconds before re-connecting.
|
6564332
|
Hot-plug operations on Sun Crypto Accelerator (SCA)6000 cards can cause SPARC Enterprise M4000/M5000 servers to panic or hang.
|
Version 1.0 of the SCA6000 driver does not support hot-plug and should not be attempted. Version 1.1 of the SCA6000 driver and firmware will support hot-plug operations after the required bootstrap firmware upgrade has been performed.
|
6564934
|
Performing a DR deleteboard operation on a board which includes Permanent Memory when using the following network cards will result in broken connections:
- X4447A-Z, PCI-e Quad-port Gigabit Ethernet Adapter UTP
- X1027A-Z1, PCI-e Dual 10 Gigabit Ethernet Fiber XFP Low profile Adapter
|
Re-configure the affected network interfaces after the completion of the DR operation. For basic network configuration procedures, refer to the if man page for more information.
|
6568417
|
After a successful CPU DR deleteboard operation, the system panics when the following network interfaces are in use:
- X4447A-Z, PCI-e Quad-port Gigabit Ethernet Adapter UTP
- X1027A-Z1, PCI-e Dual 10 Gigabit Ethernet Fiber XFP Low profile Adapter
|
Add the following line to /etc/system and reboot the system:
set ip:ip_soft_rings_cnt=0
|
6571370
|
Use of the following cards have been observed to cause data corruption in stress test under laboratory conditions:
- X4447A-Z, PCI-e Quad-port Gigabit Ethernet Adapter UTP
- X1027A-Z1, PCI-e Dual 10 Gigabit Ethernet Fiber XFP Low profile Adapter
|
Add the following line in /etc/system and reboot:
set nxge:nxge_rx_threshold_hi=0
|
6589833
|
The DR addboard command might cause a system hang if you are adding a Sun StorageTek Enterprise Class 4Gb Dual-Port Fibre Channel PCI-E HBA card (SG-XPCIE2FC-QF4) at the same time that an SAP process is attempting to access storage devices attached to this card. The chance of a system hang is increased if the following cards are used for heavy network traffic:
- X4447A-Z, PCI-e Quad-port Gigabit Ethernet Adapter UTP
- X1027A-Z1, PCI-e Dual 10 Gigabit Ethernet Fiber XFP Low profile Adapter
|
There is no workaround. Check for the availability of a patch for this defect.
|
6592302
|
Unsuccessful DR operation leaves memory partially configured.
|
To recover, add the board back to the domain with the addboard command, then retry the deleteboard command.
|
Identifying Permanent Memory in a Target Board
1. Log in to XSCF.
2. Type the following command:
XSCF> showdevices -d domain_id
|
The following example shows a display of the showdevices -d command where 0 is the domain_id.
XSCF> showdevices -d 0
...
Memory:
-------
board perm base domain target deleted remaining
DID XSB mem MB mem MB address mem MB XSB mem MB mem MB
00 00-0 8192 0 0x0000000000000000 24576
00 00-2 8192 1674 0x000003c000000000 24576
00 00-3 8192 0 0x0000034000000000 24576
...
|
The entry for column 4 perm mem MB indicates the presence of permanent memory if the value is non-zero.
The example shows permanent memory on 00-2, with 1674 MB.
If the board includes permanent memory and executes the deleteboard command or moveboard command, the following notification will appear:
System may be temporarily suspended, proceed? [y|n]:
|
Booting From a WAN Boot Server
To support booting the SPARC Enterprise M4000/M5000 server from a WAN boot server:
1. Install the Solaris 10 11/06 OS on the WAN boot server.
2. Copy the wanboot executable from that release to the appropriate location on the install server. If you need further instructions, refer to the Solaris 10 Installation Guide: Network-Based Installations or refer to:
http://docs.sun.com/app/docs/doc/817-5504/6mkv4nh65?a=view
3. Create a WAN boot miniroot from the Solaris 10 11/06 OS. If you need further instructions, refer to:
http://docs.sun.com/app/docs/doc/817-5504/6mkv4nh63?a=view
If you do not upgrade the wanboot executable, the SPARC Enterprise M4000/M5000 server will panic, with messages similar to the following:
krtld: load_exec: fail to expand cpu/$CPUkrtld: error during initial load/link phasepanic - boot: exitto64 returned from client program
See http://docs.sun.com/app/docs/doc/817-5504/6mkv4nh5i?a=view for more information on WAN boot.
Abbreviated Man Page for getflashimage
This section provides information on the abbreviated man page for getflashimage.
Synopsis
getflashimage [-v] [[-q] -{y|n}] [-u user] [-p proxy [-t proxy_type]] url
getflashimage -l
getflashimage [[-q] -{y|n}] [-d]
getflashimage -h
Description
The getflashimage (8) command downloads a firmware image file for use by the flashupdate (8) command. If any previous image files of the firmware are present on the XSCF unit, they are deleted prior to downloading the new version. You must have platadm or fieldeng privileges to run this command.
Options and Operand
The following table describes the most commonly used options and operand.
-d
|
Deletes all previous firmware image files still on the XSCF unit, then exits.
|
-l
|
Lists firmware image files that are still on the XSCF unit, then exits.
|
-u user
|
Specifies the user name when logging in to a remote ftp or http server that requires authentication. You will be prompted for a password.
|
url
|
Specifies the URL of the firmware image to download.
|
Examples
CODE EXAMPLE 1 Downloading Using a User Name and Password
This example uses the optional -u user option.
XSCF> getflashimage -u jsmith \
http://imageserver/images/FFXCP1041.tar.gz
Existing versions:
Version Size Date
FFXCP1040.tar.gz 46827123 Wed Mar 14 19:11:40 2007
Warning: About to delete old versions.
Continue? [y|n]: y
Password: [not echoed]
Removing FFXCP1040.tar.gz.
0MB received
1MB received
2MB received
...
43MB received
44MB received
45MB received
Download successful: 46827KB at 1016.857KB/s
|
CODE EXAMPLE 2 Listing Available Firmware Image Files
XSCF> getflashimage -l
Existing versions:
Version Size Date
FFXCP1040.tar.gz 46827123 Wed Mar 14 19:11:40 2007
|
CODE EXAMPLE 3 Deleting All Previous Firmware Image Files
XSCF> getflashimage -d
Existing versions:
Version Size Date
FFXCP1040.tar.gz 46827123 Wed Mar 14 19:11:40 2007
Warning: About to delete old versions.
Continue? [y|n]: y
Removing FFXCP1040.tar.gz.
|
Software Documentation Updates
This section contains late-breaking information on the software documentation that became known after the documentation set was published.
TABLE 10 Software Documentation Updates
Document
|
Page Number
|
Change
|
All SPARC Enterprise M4000/M5000 servers documentation
|
|
All DVD references are now referred to as CD-RW/DVD-RW.
|
Sun SPARC Enterprise M4000/M5000/M8000/M9000 Servers XSCF User’s Guide
|
|
The list of web browsers supported by the XSCF Web include:
- Microsoft Internet Explorer 6.0 or later
- Firefox 2.0 or later
- Mozilla 1.7 or later
- Netscape Navigator 7.1 or later
|
SPARC Enterprise M4000/M5000/M8000/ M9000 Servers Administration Guide
|
Page 2
|
Solaris OS Software section. The following Note has been added
Note: The XSCF firmware requires that all domains have the SUNWsckmr and SUNWsckmu.u packages. Since the Core System, Reduced Network, and Minimal System versions of the Solaris OS do not automatically install these packages, you must do so on any domains that do not already have them.
|
SPARC Enterprise M4000/M5000/M8000/M9000 Servers Dynamic Reconfiguration (DR) User’s Guide
|
Page 2-15
|
Update 2.3: “Conditions and Settings Using Solaris OS”
The following caution will be added:
Caution: DR is not initially supported on domains with one of the following Solaris software groups installed: Core System, Reduced Network, or Minimal System. To use DR on such a domain, you first must install the SUNWsckmr and SUNWsckmu.u packages.
|
SPARC Enterprise M4000/M5000/M8000/M9000 Servers XSCF User’s Guide
|
Page D-5
|
Frequently Asked Questions (FAQ) in “Troubleshooting XSCF and FAQ“
The option for OS dump is not "request" but "panic".
Correction:
1. First, execute the reset(8) command with the panic option from the XSCF Shell.
|
ioxadm (8) man page
|
|
The Privileges section of the ioxadm (8) man page is incomplete.
The following description is complete:
- With platop privileges, you can use the operands: env, list.
- With platadm privileges, you can use the operands: env, list, locator, poweroff, poweron.
- With fieldeng privileges, you can use the operands: env, list, locator, poweroff, poweron, reset, and setled.
|
showldap (8) man page
showlookup (8) man page
showemailreport (8) man page
|
|
The man pages for showldap, showlookup, and showemailreport do not state that these commands are available with the fieldeng privilege.
|
getflashimage (8) man page
|
|
In XCP104x, the new command getflashimage is available, which can be used to download firmware images in place of the XSCF Web.
An abbreviated man page for getflashimage is included in Abbreviated Man Page for getflashimage.
|
setaudit (8) man page
showaudit (8) man page
|
|
The setaudit and showaudit man pages are incorrect with respect to audit class information.
The following are the audit classes and their values:
ACS_SYSTEM 1
ACS_WRITE 2
ACS_READ 4
ACS_LOGIN 8
ACS_AUDIT 16
ACS_DOMAIN 32
ACS_USER 64
ACS_PLATFORM 128
ACS_MODES 256
|
Sun SPARC Enterprise M4000/M5000 Servers Product Notes for XCP Version 1041
|
820-2221-13
|
![Table Of Contents Table Of Contents](shared/toc01.gif) ![Previous Chapter Previous Chapter](shared/prev01.gif) ![NoNext NoNext](shared/next02.gif) ![NoIndex NoIndex](shared/index02.gif) |
Copyright © 2007, Sun Microsystems, Inc. All Rights Reserved.