Documentation, Support, and Training
Understanding Administrative Commands
Understanding the Component Addressing Scheme
Line Card CXP Connector Addressing
Switch-Specific Command Overview
InfiniBand Software Command Overview
Display the General Health of the Switch
Display Power Supplies Present
Check the Status of a Power Supply
Display the Firmware Version of a Power Supply
Check Internal Power and Temperature of a CMC
Check the Status LEDs of a CMC
Display the Firmware Version of a CMC
Display the Firmware Version of the Switch Chassis Manager
Check Fabric Card Power Faults
Check the Internal Power and Temperature of a Fabric Card
Check Fabric Card Internal Temperatures
Check Fabric Card Internal Voltages
Display the Base GUIDs of a Fabric Card
Check Fabric Card Link Status (Simple)
Check Fabric Card Link Status (Detailed)
Check Fabric Card Switch Chip Health
Check the IPMB State of a Fabric Card
Check the Status LEDs of a Fabric Card
Display the Firmware Versions of a Fabric Card
Check the Internal Power and Temperature of a Line Card
Check Line Card Internal Temperatures
Check Line Card Internal Voltages
Display the Base GUIDs of a Line Card
Check Line Card Link Status (Simple)
Check Line Card Link Status (Detailed)
Check Line Card Switch Chip Health
Check the IPMB State of a Line Card
Check the Status LEDs of a Line Card
Display the Firmware Versions of a Line Card
Checking Other Switch Characteristics
Display the Network Management Configuration
Locate a Switch Chip or Connector From the GUID
Monitoring the InfiniBand Fabric
Display Information About the Local HCA
Identify All HCAs in the Fabric
Identify All Switches in the Fabric
Display the InfiniBand Fabric Topology
Display a Route Through the Fabric
Display the Link Status of a Node
Display Data Counters for a Node
Display Low-Level Detailed Information About a Node
Display Low-Level Detailed Information About a Port
Determine the GUID and LID for a Node Within the Switch
Display OFED Software Version Information
Reconfigure the Network Management Parameters
Reconfigure the CMCs for Identical Addresses
Enable and Activate a Power Supply
Deactivate and Disable a Power Supply
Restart a Fabric Card or Filler
Enable a Fabric Card or Filler
Disable a Fabric Card or Filler
Enable Standby Power for a Fabric Card or Filler
Disable Standby Power for a Fabric Card or Filler
Enable a Fabric Card Slot for Hot-Insertion
Activate a Fabric Card or Filler
Deactivate a Fabric Card or Filler
Turn On a Fabric Card or Filler Locator LED
Turn Off a Fabric Card or Filler Locator LED
Enable Downed Fabric Card Links
Enable a Fabric Card Switch Chip Port
Disable a Fabric Card Switch Chip Port
Reset a Fabric Card Switch Chip
Enable Standby Power for a Line Card
Disable Standby Power for a Line Card
Enable a Line Card Slot for Hot-Insertion
Turn On a Line Card Locator LED
Turn Off a Line Card Locator LED
Enable a Line Card Switch Chip Port
Disable a Line Card Switch Chip Port
Controlling the InfiniBand Fabric
Perform Comprehensive Diagnostics for the Entire Fabric
Perform Comprehensive Diagnostics for a Route
Determine Changes to the InfiniBand Fabric Topology
Find 1x or SDR or DDR Links in the Fabric
Determine Which Links Are Experiencing Significant Errors
Controlling the Subnet Manager
Start the Subnet Manager With Min Hop Routing
Start the Subnet Manager With Fat Tree Routing
Start the Subnet Manager With the opensmd Daemon
Stop the Subnet Manager With the opensmd Daemon
Understanding ILOM on the Switch
You can change the host name of the CMC to something which identifies the CMC or the switch where it is installed.
Note - The host name is propagated to the NodeDescription field seen in the output of many InfiniBand software commands.
Access the CMC from its serial management port.
Log in, then invoke a reboot of the CMC:
# reboot
The CMC reboots.
When you see the following output, press any key to stop the boot process:
hit any key to stop autoboot
The boot monitor prompt is displayed.
shmm1500
Set the backup state IP address of the CMC:
shmm1500 setenv hostname hostname
where hostname is the identifier to apply to the CMC. For example:
shmm1500 setenv hostname CMC-A
Save the configuration and continue booting the switch:
shmm1500 saveenv shmm1500 boot
The switch boots.
The boot monitor prompt is now the hostname. For example:
CMC-A boot
The hostname is also propagated to the NodeDescription field in the output of the m9diag command and InfiniBand software commands. For example:
# m9diag Oct 22 18:16:47 CMC-A user.warn kernel: POST memory PASSED Oct 22 18:16:47 CMC-A user.warn kernel: POST i2c PASSED Oct 22 18:16:47 CMC-A user.warn kernel: POST uart PASSED Oct 22 18:16:47 CMC-A user.warn kernel: POST ethernet PASSED . . . #
Switch Reference, ibswitches command