- Document Information
- Using This Documentation
- Installation
- Preparing the Site
- Installing the Switch
- Understanding the Installation
- Supported Configurations
- Fabric Card Distribution
- Fabric Card Handling Guidelines
- Line Card Distribution
- Line Card Handling Guidelines
- Fabric Card and Line Card Fillers
- Installation Preparation
- Suggested Tools for Installation
- Antistatic Precautions for Installation
- Installation Responsibilities
- Installation Sequence
- Installing the InfiniBand Software Stack
- Unpacking the Chassis
- Preparing the Chassis
- Inspecting the Components
- Installing the Components
- Powering On the CMCs
- Attach the Management Cables
- Attach the Power Cords
- Check the Power Supply Status LEDs
- Check the CMC Status LEDs
- Accessing the CMC
- Verify the CMC Status
- Identify the CMC Addresses
- Display the CMC FRU ID Information
- Verify the Power Supply Status
- Identify the Power Supply Addresses
- Display the Power Supply FRU ID Information
- Powering On the Fabric Cards
- Powering On the Line Cards
- Connecting InfiniBand Cables
- Verifying the InfiniBand Fabric
- Understanding the Installation
- Administration
- Administering the Switch
- Understanding Administrative Commands
- Monitoring the Switch
- Performing General Tasks
- Checking Power Supplies
- Checking CMCs
- Checking Fabric Cards
- Check Fan Speed and Status
- Display Fabric Cards Present
- Check Fabric Card Power Faults
- Check the Internal Power and Temperature of a Fabric Card
- Check Fabric Card Internal Temperatures
- Check Fabric Card Internal Voltages
- Display the Base GUIDs of a Fabric Card
- Check Fabric Card Link Status (Simple)
- Check Fabric Card Link Status (Detailed)
- Check Fabric Card Switch Chip Health
- Check the IPMB State of a Fabric Card
- Check the Status LEDs of a Fabric Card
- Display the Firmware Versions of a Fabric Card
- Checking Line Cards
- Display Line Cards Present
- Check Line Card Power Faults
- Check the Internal Power and Temperature of a Line Card
- Check Line Card Internal Temperatures
- Check Line Card Internal Voltages
- Display the Base GUIDs of a Line Card
- Check Line Card Link Status (Simple)
- Check Line Card Link Status (Detailed)
- Check Line Card Switch Chip Health
- Check the IPMB State of a Line Card
- Check the Status LEDs of a Line Card
- Display the Firmware Versions of a Line Card
- Checking Other Switch Characteristics
- Monitoring the InfiniBand Fabric
- Display Information About the Local HCA
- Identify All HCAs in the Fabric
- Identify All Switches in the Fabric
- Display the InfiniBand Fabric Topology
- Display a Route Through the Fabric
- Display the Link Status of a Node
- Display Counters for a Node
- Display Data Counters for a Node
- Display Low-Level Detailed Information About a Node
- Display Low-Level Detailed Information About a Port
- Map LIDs to GUIDs
- Determine the GUID and LID for a Node Within the Switch
- Display Subnet Manager Status
- Display OFED Software Version Information
- Controlling the Switch
- Setting Up the Hardware
- Setting Up the Users
- Managing Power Supplies
- Managing CMCs
- Managing Fabric Cards
- Restart a Fabric Card or Filler
- Enable a Fabric Card or Filler
- Disable a Fabric Card or Filler
- Enable Standby Power for a Fabric Card or Filler
- Disable Standby Power for a Fabric Card or Filler
- Enable a Fabric Card Slot for Hot-Insertion
- Activate a Fabric Card or Filler
- Deactivate a Fabric Card or Filler
- Turn On a Fabric Card or Filler Locator LED
- Turn Off a Fabric Card or Filler Locator LED
- Enable Downed Fabric Card Links
- Enable a Fabric Card Switch Chip Port
- Disable a Fabric Card Switch Chip Port
- Reset a Fabric Card Switch Chip
- Managing Line Cards
- Restart a Line Card
- Enable a Line Card
- Disable a Line Card
- Enable Standby Power for a Line Card
- Disable Standby Power for a Line Card
- Enable a Line Card Slot for Hot-Insertion
- Activate a Line Card
- Deactivate a Line Card
- Turn On a Line Card Locator LED
- Turn Off a Line Card Locator LED
- Enable Downed Line Card Links
- Enable a Line Card Switch Chip Port
- Disable a Line Card Switch Chip Port
- Reset a Line Card Switch Chip
- Controlling the InfiniBand Fabric
- Perform Comprehensive Diagnostics for the Entire Fabric
- Perform Comprehensive Diagnostics for a Route
- Determine Changes to the InfiniBand Fabric Topology
- Find 1x or SDR or DDR Links in the Fabric
- Determine Which Links Are Experiencing Significant Errors
- Clear Error Counters
- Clear Data Counters
- Check All Ports
- Reset a Port
- Set the Speed of a Port
- Disable a Port
- Enable a Port
- Controlling the Subnet Manager
- Diagnosing a Problem
- Identifying the Problem
- Troubleshooting the Switch
- Understanding Signal Routing Through the Switch
- CXP Connectors and LEDs to Line Card Switch Chip and Port Routes
- Line Card Switch Chip to Line Card XBOW Connector Routes
- Fabric Card XBOW Connector to Fabric Card Switch Chip Routes
- Fabric Card Switch Chip to Fabric Card XBOW Connector Routes
- Line Card XBOW Connector to Line Card Switch Chip Routes
- Line Card Switch Chip and Port to CXP Connector and LED Routes
- Signal Route Through the Switch
- Understanding Switch Startup and Component Addition
- Switch GUIDs Overview
- Administering the Switch
- Remote Management
- Understanding ILOM on the Switch
- Installing the ILOM Firmware
- Administering ILOM (CLI)
- CLI Overview
- Access ILOM From the CLI
- Switching Between the ILOM Shell and the Linux Shell
- Monitoring ILOM Targets (CLI)
- Performing Daily Tasks (CLI)
- Checking the Status of Services (CLI)
- Verifying Other Aspects (CLI)
- Get Help on an ILOM Command (CLI)
- Get Help on an ILOM Target Property (CLI)
- Display the Alert Properties (CLI)
- Display the ILOM User Accounts (CLI)
- Display the Remote Log Hosts (CLI)
- Display the Network Management Configuration (CLI)
- Display the ILOM CLI Session Timeout (CLI)
- Display Chassis FRU ID Information (CLI)
- Display the ILOM Firmware Version (CLI)
- Controlling ILOM Targets (CLI)
- Performing General Tasks on ILOM Targets (CLI)
- Performing ILOM User Tasks (CLI)
- Managing HTTP Services (CLI)
- Managing HTTPS Services (CLI)
- Managing SNMP Services (CLI)
- Enable the SNMP Service (CLI)
- Configure the SNMP Service (CLI)
- Add SNMP Service User Accounts (CLI)
- Modify SNMP Service User Accounts (CLI)
- Delete SNMP Service User Accounts (CLI)
- Add SNMP Service Communities (CLI)
- Modify SNMP Service Communities (CLI)
- Delete SNMP Service Communities (CLI)
- Back Up SNMP Service MIBs (CLI)
- Disable the SNMP Service (CLI)
- Managing Other Aspects (CLI)
- Upgrading the Switch Firmware Through ILOM (CLI)
- Administering ILOM (Web Interface)
- Web Interface Overview
- Access ILOM From the Web Interface
- Monitoring ILOM Targets (Web Interface)
- Performing Daily Tasks (Web Interface)
- Checking the Status of Services (Web Interface)
- Display the HTTP Service Status (Web Interface)
- Display the HTTPS Service Status (Web Interface)
- Display the SSL Certificates (Web Interface)
- Display the SNMP Service Status (Web Interface)
- Display the SNMP Service User Accounts (Web Interface)
- Display the SNMP Service Communities (Web Interface)
- Display the IPMI Service Status (Web Interface)
- Verifying Other Aspects (Web Interface)
- Display the Alert Properties (Web Interface)
- Display the ILOM User Accounts (Web Interface)
- Display the Remote Log Hosts (Web Interface)
- Display the Network Management Configuration (Web Interface)
- Display the ILOM CLI Session Timeout (Web Interface)
- Display Chassis FRU ID Information (Web Interface)
- Display the ILOM Firmware Version (Web Interface)
- Controlling ILOM Targets (Web Interface)
- Performing General Tasks on ILOM Targets (Web Interface)
- Set the Date and Time (Web Interface)
- Set the Time Zone (Web Interface)
- Clear the ILOM Event Log (Web Interface)
- Set the Remote Log Hosts (Web Interface)
- Back Up the ILOM Configuration (Web Interface)
- Restore the ILOM Configuration (Web Interface)
- Set the Network Management Parameters (Web Interface)
- Performing ILOM User Tasks (Web Interface)
- Managing HTTP Services (Web Interface)
- Managing HTTPS Services (Web Interface)
- Managing SNMP Services (Web Interface)
- Enable the SNMP Service (Web Interface)
- Configure the SNMP Service (Web Interface)
- Add SNMP Service User Accounts (Web Interface)
- Modify SNMP Service User Accounts (Web Interface)
- Delete SNMP Service User Accounts (Web Interface)
- Add SNMP Service Communities (Web Interface)
- Modify SNMP Service Communities (Web Interface)
- Delete SNMP Service Communities (Web Interface)
- Back Up SNMP Service MIBs (Web Interface)
- Disable the SNMP Service (Web Interface)
- Managing Other Aspects (Web Interface)
- Performing General Tasks on ILOM Targets (Web Interface)
- Upgrading the Switch Firmware Through ILOM (Web Interface)
- Administering ILOM (SNMP)
- SNMP Overview
- SNMP Commands
- Monitoring ILOM Targets (SNMP)
- Controlling ILOM Targets (SNMP)
- Administering Hardware (IPMI)
- Understanding ILOM Commands
- Service
- Servicing the Switch
- Understanding Service Procedures
- Servicing the Power Supplies
- Servicing the CMCs
- Servicing the Fans
- Servicing the Fabric Cards and Fabric Card Fillers
- Servicing the InfiniBand Cables
- Servicing the Line Cards
- Doing Supportive Software Tasks
- Servicing the Switch
- Reference
- Command Reference
- Understanding Switch-Specific Commands
- activate Command (switch-specific)
- checkfans Command
- checklinks Command
- checkpowers Command
- checkpwrfault Command
- checkswitches Command
- checkvoltages Command
- clearboardstat Command
- deactivate Command (switch-specific)
- disableboard Command
- disablepsu Command
- disablestby Command
- disableswitchport Command
- enableboard Command
- enablehotinsert Command
- enablepsu Command
- enablestby Command
- enableswitchport Command
- env_test Command
- findport Command
- getbaseguid Command
- getboardstat Command
- getfwversion Command
- getportcounters Command
- getportstatus Command
- getpsufwver Command
- getserialnumbers Command
- getsymerr Command
- i2ctest Command
- m9diag Command
- mcmversion Command
- psustatus Command
- resetswitch Command
- selectdebugport Command
- setlinkspeed Command
- showlogs Command
- showpresent Command
- showtemps Command
- showvoltages Command
- Understanding CLIA Commands
- activate Command (CLIA)
- deactivate Command (CLIA)
- exit Command (CLIA)
- fru Command
- frucontrol Command
- fruinfo Command
- getfruledstate Command
- getipmbstate Command
- getlanconfig Command
- LAN Configuration Parameters
- help Command (CLIA)
- ipmc Command
- localaddress Command
- poll Command
- quit Command
- sel Command
- sensordata Command
- session Command
- setextracted Command
- setfruledstate Command
- setipmbstate Command
- setlanconfig Command
- setlocked Command
- shelf Command
- shelfaddress Command
- shmstatus Command
- showunhealthy Command
- switchover Command
- terminate Command
- user [-v] Command
- user add Command
- user channel Command
- user delete Command
- user enable Command
- user name Command
- user passwd Command
- version Command (CLIA)
- Understanding InfiniBand Software Commands
- ib_read_bw Command
- ib_read_lat Command
- ib_send_bw Command
- ib_send_lat Command
- ib_write_bw Command
- ib_write_lat Command
- ibaddr Command
- ibcheckerrors Command
- ibchecknet Command
- ibchecknode Command
- ibcheckport Command
- ibcheckportstate Command
- ibcheckportwidth Command
- ibcheckstate Command
- ibcheckwidth Command
- ibclearcounters Command
- ibclearerrors Command
- ibdatacounters Command
- ibdatacounts Command
- ibdiagnet Command
- ibdiagpath Command
- ibhosts Command
- ibnetdiscover Command
- ibnodes Command
- ibping Command
- ibportstate Command
- ibroute Command
- ibrouters Command
- ibstat Command
- ibstatus Command
- ibswitches Command
- ibsysstat Command
- ibtracert Command
- ibv_devices Command
- ibv_devinfo Command
- ibv_rc_pingpong Command
- ibv_srq_pingpong Command
- ibv_uc_pingpong Command
- ibv_ud_pingpong Command
- ofed_info Command
- opensm Command
- opensmd Daemon
- osmtest Command
- perfquery Command
- saquery Command
- sminfo Command
- smpdump Command
- smpquery Command
- vendstat Command
- Understanding Switch-Specific Commands
- Command Reference
- Index
Sun Datacenter InfiniBand Switch 648 Topic Set
May 2010, Revision 01
This topic set provides installation, administration, remote administration, service, and command reference information for the Sun Datacenter InfiniBand Switch 648 from Oracle. This topic set is for installers, system and network administrators, service personnel, and any user qualified to install, manage, or service infiniBand networking devices.
