JavaScript is required to for searching.
Skip Navigation Links
Exit Print View
Oracle Solaris Administration: IP Services     Oracle Solaris 11 Information Library
search filter icon
search icon

Document Information


Part I TCP/IP Administration

1.  Planning the Network Deployment

2.  Considerations When Using IPv6 Addresses

3.  Configuring an IPv4 Network

4.  Enabling IPv6 on the Network

5.  Administering a TCP/IP Network

6.  Configuring IP Tunnels

7.  Troubleshooting Network Problems

8.  IPv4 Reference

9.  IPv6 Reference


10.  About DHCP (Overview)

11.  Administering the ISC DHCP Service

12.  Configuring and Administering the DHCP Client

13.  DHCP Commands and Files (Reference)

Part III IP Security

14.  IP Security Architecture (Overview)

15.  Configuring IPsec (Tasks)

16.  IP Security Architecture (Reference)

17.  Internet Key Exchange (Overview)

18.  Configuring IKE (Tasks)

19.  Internet Key Exchange (Reference)

20.  IP Filter in Oracle Solaris (Overview)

21.  IP Filter (Tasks)

Part IV Networking Performance

22.  Integrated Load Balancer Overview

23.  Configuration of Integrated Load Balancer (Tasks)

24.  Virtual Router Redundancy Protocol (Overview)

25.  VRRP Configuration (Tasks)

26.  Implementing Congestion Control

Part V IP Quality of Service (IPQoS)

27.  Introducing IPQoS (Overview)

28.  Planning for an IPQoS-Enabled Network (Tasks)

29.  Creating the IPQoS Configuration File (Tasks)

30.  Starting and Maintaining IPQoS (Tasks)

Administering IPQoS (Task Map)

Applying an IPQoS Configuration

How to Apply a New Configuration to the IPQoS Kernel Modules

How to Ensure That the IPQoS Configuration Is Applied After Each Reboot

Enabling syslog Logging for IPQoS Messages

How to Enable Logging of IPQoS Messages During Booting

Troubleshooting with IPQoS Error Messages

31.  Using Flow Accounting and Statistics Gathering (Tasks)

32.  IPQoS in Detail (Reference)



Applying an IPQoS Configuration

You activate and otherwise manipulate the IPQoS configuration by using the ipqosconf command.

How to Apply a New Configuration to the IPQoS Kernel Modules

You use the ipqosconf command to read the IPQoS configuration file and to configure the IPQoS modules in the UNIX kernel. The next procedure uses as an example the file /var/ipqos/Goldweb.qos, which is created in Creating IPQoS Configuration Files for Web Servers. For detailed information, refer to the ipqosconf(1M) man page.

  1. Apply the new configuration.
    # /usr/sbin/ipqosconf -a/var/ipqos/Goldweb.qos

    ipqosconf writes the information in the specified IPQoS configuration file into the IPQoS modules in the Oracle Solaris kernel. In this example, the contents of /var/ipqos/Goldweb.qos are applied to the current Oracle Solaris kernel.

    Note - When you apply an IPQoS configuration file with the -a option, the actions in the file are active for the current session only.

  2. Test and debug the new IPQoS configuration.

    Use UNIX utilities to track IPQoS behavior and to gather statistics on your IPQoS implementation. This information can help you determine if the configuration operates as expected.

See Also

How to Ensure That the IPQoS Configuration Is Applied After Each Reboot

You must explicitly make an IPQoS configuration persistent across reboots. Otherwise, the current configuration applies only until the system reboots. When IPQoS works correctly on a system, do the following to make the configuration persistent across reboots.

  1. Test for the existence of an IPQoS configuration in the kernel modules.
    # ipqosconf -l

    If a configuration already exists, ipqosconf displays the configuration on the screen. If you do not receive output, apply the configuration, as explained in How to Apply a New Configuration to the IPQoS Kernel Modules.

  2. Ensure that the existing IPQoS configuration is applied every time the IPQoS system reboots.
    # /usr/sbin/ipqosconf -c

    The -c option causes the current IPQoS configuration to be represented in the boot-time configuration file /etc/inet/ipqosinit.conf.