In this section, you configure publishing and production ATG server instances.
To configure your ATG server instances:
In the CIM MAIN MENU, select [2] Server Instance Configuration.
In the SERVER INSTANCE TYPE SELECTION menu, select [P] Publishing Server - 0 Instances Configured.
In the SERVER INSTANCE TYPE CONFIGURATION menu, select [P] Publishing Server General Configuration - REQUIRED.
Enter the following information for your publishing server instance. In most cases, you can accept the defaults. The exception is the Endeca base application name. The defaults are provided in brackets.
Production Lock Server host name
Production Lock Server port [9012]
CAS host name [localhost]
CAS port [8500]
EAC host name [localhost]
EAC port [8888]
Endeca base application name. Do not accept the
ATG
default. Instead, enterCRS
for this value.Fully-qualified Workbench host name, including domain
Workbench port [8006]
Default MDEX host name [localhost]
Default MDEX port number [15000]
In the SERVER INSTANCE TYPE CONFIGURATION menu, select [I] Instance Management – REQUIRED.
In the INSTANCE MANAGEMENT menu, select [A] Add Server Instance.
In the Select Type of Server Instance To Create menu, select [1] Publishing with a Server Lock Manager: Minimum 1 Required.
In the NAME FOR NEW SERVER INSTANCE menu, enter
ATGPublishing
for the Server Instance Name.(WebLogic Only) Perform these steps for WebLogic environments only:
In the WEBLOGIC ONLINE PORT BINDING menu, select [C] Choose Custom Port Binding.
In the CHOOSE CUSTOM WEBLOGIC ONLINE PORT BINDING menu, select [2] ports-01: http port is 7103.
(JBoss Only) Perform these steps for JBoss environments only:
In the JBOSS PORT BINDING menu, select [C] Choose Custom Port Binding.
In the CHOOSE CUSTOM JBOSS PORT BINDING menu, select [2] ports-01: http port is 8180.
(WebSphere Only) Perform these steps for WebSphere environments only:
In the WEBSPHERE PORT BINDING menu, select [C] Choose Custom Port Binding.
In the CHOOSE CUSTOM WEBSPHERE PORT BINDING menu, select [2] ports-01: http port is 9181.
Enter the following ports. The defaults CIM provides for each application server are listed in the table below. You can leave the defaults as is unless they cause port conflicts on your machine.
Port Type
WebLogic Default
JBoss Default
WebSphere Default
HTTP Port
7103
8180
9181
HTTPS Port
7104
8543
9544
Site HTTP Port
7103
8180
9181
RMI Port
8861
8861
8861
DRP Port
8851
8851
8851
File Deployment Port
8811
8811
8811
File Synchronization Deploy Server Port
8816
8816
8816
Lock Server Port
9010
9010
9010
Note: By default the Sun T1000 and T2000 systems run a server that uses port 9010. ATG’s lock management components also use this port. If you are using lock management on one of these systems, you must either disable the Sun server or use a different lock server port while configuring your server instance. See the Sun T1000 and T2000 Requirements in the ATG Installation and Configuration Guide for detailed instructions.
In the INSTANCE MANAGEMENT menu, select [D] Done.
In the SERVER INSTANCE TYPE CONFIGURATION menu, select [O] Configure Another Server Instance Type.
In the SERVER INSTANCE TYPE SELECTION menu, select [S] Production Server - 0 Instances Configured.
In the SERVER INSTANCE TYPE CONFIGURATION menu, select [P] Production Server General Configuration - REQUIRED.
Enter the following information for your production server instance. Note that the defaults have been updated based on the information you provided for the publishing server so, for some settings, you should be able to accept the default values.
CAS host name [localhost]
CAS port [8500]
EAC host name [localhost]
EAC port [8888]
Endeca base application name. Accept the
CRS
default.Fully-qualified Workbench host name, including domain
Workbench port [8006]
Default MDEX host name [localhost]
Default MDEX port number [15000]
In the SERVER INSTANCE TYPE CONFIGURATION menu, select [I] Instance Management – REQUIRED.
In the INSTANCE MANAGEMENT menu, select [A] Add Server Instance.
In the Select Type of Server Instance To Create menu, select [1] Production with a Server Lock Manager: Minimum 1 Required.
In the NAME FOR NEW SERVER INSTANCE menu, enter
ATGProduction
for the Server Instance Name.In the <
Application_Server
> ONLINE PORT BINDING menu, select [U] Use Default Port Binding.Enter the following ports. The defaults CIM provides for each application server are listed in the table below. You can leave the defaults as is unless they cause port conflicts on your machine.
Port Type
WebLogic Default
JBoss Default
WebSphere Default
HTTP Port
7003
8080
9081
HTTPS Port
7004
8443
9444
Site HTTP Port
7003
8080
9081
RMI Port
8860
8860
8860
DRP Port
8850
8850
8850
File Deployment Port
8810
8810
8810
Lock Server Port
9012
9012
9012
In the INSTANCE MANAGEMENT menu, select [D] Done.
In the SERVER INSTANCE TYPE CONFIGURATION menu, select [O] Configure Another Server Instance Type.
In the SERVER INSTANCE TYPE SELECTION menu, select [D] Done.
Continue with the section Creating the Endeca Application.