CLI를 사용하여 네트워크 구성

네트워크 구성은 configuration net 아래에 있고 이 명령에는 devices, datalinks, interfaces 및 routing에 대한 하위 명령이 있습니다. 각 하위 명령을 show 명령과 함께 사용하여 현재 구성을 표시할 수 있습니다.

caji:> configuration net
caji:configuration net> devices show
Devices:

DEVICE      UP     SPEED         MAC                                            
igb0        true   1000 Mbit/s   0:14:4f:9a:b9:0                               
igb1        true   1000 Mbit/s   0:14:4f:9a:b9:1                               
igb2        true   1000 Mbit/s   0:14:4f:9a:b8:fe                              
igb3        true   1000 Mbit/s   0:14:4f:9a:b8:ff                              

caji:configuration net> datalinks show
Datalinks:

   DATALINK CLASS          LINKS       LABEL
       igb0 device         igb0        datalink1

caji:configuration net> interfaces show
Interfaces:

  INTERFACE STATE  CLASS LINKS       ADDRS                  LABEL
       igb0 up     ip    igb0        192.168.2.80/22        caji
 
caji:configuration net> routing show
Properties:
                  multihoming = loose
 
Routes:
 
ROUTE      DESTINATION                      GATEWAY         INTERFACE TYPE
route-000  0.0.0.0/0                        192.168.1.1     igb0      dhcp
route-001  192.168.0.0/22                   192.168.2.142   igb0      system

데이터 링크, 인터페이스 및 경로를 만들고 구성하는 것과 관련된 명령을 보려면 각 절에서 help를 입력하십시오. 이 컨텍스트에서 유효한 하위 명령은 다음과 같습니다.

  help [topic]         => Get context-sensitive help. If [topic] is specified,
                          it must be one of "builtins", "commands","general",
                          "help", "script" or "properties".

  show                 => Show information pertinent to the current context

  commit               => Commit current state, including any changes

  abort                => Abort creation of "vnic"

  done                 => Finish operating on "vnic"

  get [prop]           => Get value for property [prop]. ("help properties"
                          for valid properties.) If [prop] is not specified,
                          returns values for all properties.

  set [prop]           => Set property [prop] to [value]. ("help properties"
                          for valid properties.) For properties taking list
                          values, [value] should be a comma-separated list of
                          values. 

  available            => Get values that can be assigned to the links
                          parameter when creating a network component.

available 명령은 네트워크 구성 요소를 만들 때 links 매개변수에 지정할 수 있는 값을 확인하는 데 사용됩니다. 다음은 CLI 명령 available의 출력을 보여 줍니다.

caji:configuration net datalinks> device
caji:configuration net datalinks device (uncommitted)> available
igb7,igb6

caji:configuration net datalinks> vnic
caji:configuration net datalinks vnic (uncommitted)> available
igb5,igb4,aggr2,aggr1

caji:configuration net datalinks> vlan
caji:configuration net datalinks vlan (uncommitted)> available
igb5,igb4,aggr2,aggr1

caji:configuration net datalinks> aggregation
caji:configuration net datalinks aggregation (uncommitted)> available
igb7,igb6

caji:configuration net interfaces> ip
caji:configuration net interfaces ip (uncommitted)> available
aggr2,aggr1

caji:configuration net interfaces> ipmp
caji:configuration net interfaces ipmp (uncommitted)> available
vnic4,vnic3,igb5,igb4

다음은 device 명령을 사용하여 데이터 링크를 만들고 ip 명령을 사용하여 인터페이스를 만드는 방법을 보여 줍니다.

caji:configuration net> datalinks 
caji:configuration net datalinks> device
caji:configuration net datalinks device (uncommitted)> set links=igb1
                          links = igb1 (uncommitted)
caji:configuration net datalinks device (uncommitted)> set label=datalink2
                          label = datalink2 (uncommitted)
caji:configuration net datalinks device (uncommitted)> set mtu=9000
                          mtu = 9000 (uncommitted)
caji:configuration net datalinks device (uncommitted)> commit
caji:configuration net datalinks> show
Datalinks:

   DATALINK CLASS          LINKS       LABEL
       igb0 device         igb0        datalink1
       igb1 device         igb1        datalink2

caji:configuration net datalinks> cd ..
caji:configuration net> interfaces
caji:configuration net interfaces> ip
caji:configuration net interfaces ip (uncommitted)> set label="caji2"
                         label = caji2 (uncommitted)
caji:configuration net interfaces ip (uncommitted)> set links=igb1 
                         links = igb1 (uncommitted)
caji:configuration net interfaces ip (uncommitted)> set v4addrs=10.0.1.1/8
                       v4addrs = 10.0.1.1/8 (uncommitted)
caji:configuration net interfaces ip (uncommitted)> commit
caji:configuration net interfaces> show
Interfaces:

  INTERFACE STATE  CLASS LINKS       ADDRS                  LABEL
       igb0 up     ip    igb0        192.168.2.80/22        caji
       igb1 up     ip    igb1        10.0.1.1/8             caji2

다음은 새 igb1 IP 인터페이스를 통해 10.0.1.2를 경유하는 기본 경로를 만드는 방법을 보여 줍니다.

caji:configuration net routing> create
caji:configuration net route (uncommitted)> set family=IPv4
                   family = IPv4 (uncommitted)
caji:configuration net route (uncommitted)> set destination=0.0.0.0
                   destination = 0.0.0.0 (uncommitted)
caji:configuration net route (uncommitted)> set mask=0
                   mask = 0 (uncommitted)
caji:configuration net route (uncommitted)> set interface=igb1
                   interface = igb1 (uncommitted)
caji:configuration net route (uncommitted)> set gateway=10.0.1.2
                   gateway = 10.0.1.2 (uncommitted)
caji:configuration net route (uncommitted)> commit

탐색 링크 건너뛰기
인쇄 보기 종료
	Oracle^® ZFS Storage Appliance 관리 설명서