配置管理接口 (CLI)

语言：

使用以下过程可配置管理接口。

转到 configuration net，然后输入 datalinks。

hostname:> configuration net
hostname:configuration net> datalinks

输入 show 以查看数据链路。

hostname:configuration net datalinks> show
Datalinks:

DATALINK        CLASS        LINKS        STATE        ID        LABEL
igb0            device       igb0         up           -         Untitled Datalink

通过转到 vnic 上下文并设置其标签指出管理数据链路用于管理，从而为该链路创建虚拟网络接口卡 (Virtual Network Interface Card, VNIC)，（可选）并选择分配虚拟 LAN (virtual LAN, VLAN) ID。输入 commit 并输入 cd ..，返回下一步的正确上下文。

hostname:configuration net datalinks> vnic
hostname:configuration net datalinks vnic (uncommitted)> set links=igb0
                          links = igb0 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> set label=management-datalink-1
                          label = management-datalink-1 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> commit
hostname:configuration net datalinks vnic> cd ..

分配 VLAN ID：

hostname:configuration net datalinks vnic> set id=100
                              id = 100 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> commit
hostname:configuration net datalinks vnic> cd ..

如果是群集控制器，请通过转到 vnic 上下文并设置唯一标签，为第二个管理数据链路创建 VNIC，（可选）并分配 VLAN ID。输入 commit 并输入 cd ..，返回下一步的正确上下文。

hostname:configuration net datalinks> vnic
hostname:configuration net datalinks vnic (uncommitted)> set links=igb0
                          links = igb0 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> set label=management-datalink-2
                          label = management-datalink-2 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> commit
hostname:configuration net datalinks vnic> cd ..

分配 VLAN ID：

hostname:configuration net datalinks vnic (uncommitted)> set id=100
                              id = 100 (uncommitted)
hostname:configuration net datalinks vnic> commit
hostname:configuration net datalinks vnic> cd ..

为控制器创建 IP 接口并将其分配给 VNIC。

hostname:configuration net> interfaces
hostname:configuration net interfaces> ip
hostname:configuration net interfaces ip (uncommitted)> set v4addrs=192.168.1.101/24
                              v4addrs = 192.168.1.101/24 (uncommitted)
hostname:configuration net interfaces ip (uncommitted)> set label=management-controller-1
                              label = management-controller-1 (uncommitted)
hostname:configuration net interfaces ip (uncommitted)> set links=vnic1
                              links = vnic1 (uncommitted)
hostname:configuration net interfaces ip (uncommitted)> commit

如果是群集控制器，请为第二个控制器创建 IP 接口并将其分配给 VNIC。依次输入 commit 和 done。

hostname:configuration net interfaces> ip
hostname:configuration net interfaces ip (uncommitted)> set v4addrs=192.168.1.102/24
                              v4addrs = 192.168.1.102/24 (uncommitted)
hostname:configuration net interfaces ip (uncommitted)> set label=management-controller-2
                              label = management-controller-2 (uncommitted)
hostname:configuration net interfaces ip (uncommitted)> set links=vnic2
                              links = vnic2 (uncommitted)
hostname:configuration net datalinks vnic (uncommitted)> commit
hostname:configuration net datalinks> done

为第一个控制器配置路由。如果是群集控制器，请为第二个控制器配置路由。依次输入 commit 和 done。

第一个控制器：

hostname:configuration net> routing
hostname:configuration net routing> create
hostname:configuration net route (uncommitted)> set destination=0.0.0.0
                        destination = 0.0.0.0 (uncommitted)
hostname:configuration net route (uncommitted)> set mask=0
                          mask = 0 (uncommitted)
hostname:configuration net route (uncommitted)> set interface=vnic1
                      interface = vnic1 (uncommitted)
hostname:configuration net route (uncommitted)> set gateway=192.168.1.1
                         gateway = 192.168.1.1 (uncommitted)
hostname:configuration net route (uncommitted)> set family=IPv4
                          family = IPv4
hostname:configuration net route (uncommitted)> commit
hostname:configuration net route> done

第二个控制器：

hostname:configuration net> routing
hostname:configuration net routing> create
hostname:configuration net route (uncommitted)> set destination=0.0.0.0
                        destination = 0.0.0.0 (uncommitted)
hostname:configuration net route (uncommitted)> set mask=0
                          mask = 0 (uncommitted)
hostname:configuration net route (uncommitted)> set interface=vnic2
                      interface = vnic2 (uncommitted)
hostname:configuration net route (uncommitted)> set gateway=192.168.1.1
                         gateway = 192.168.1.1 (uncommitted)
hostname:configuration net route (uncommitted)> set family=IPv4
                          family = IPv4
hostname:configuration net route (uncommitted)> commit
hostname:configuration net route> done

销毁名为 "Untitled Interface"（未命名的接口）的默认接口，依次输入 cd .. 和 done。

注 - 删除接口时，所有与该接口关联的路由也会删除。

hostname:configuration net> interfaces
hostname:configuration net interfaces> show
Interfaces:
    
INTERFACE   STATE     CLASS  LINKS   ADDRS                  LABEL
igb0        up        ip     igb0    192.168.1.101/24       Untitled Interface
vnic1       duplicate ip     vnic1   192.168.1.101/24       management-controller-1
vnic2       duplicate ip     vnic2   192.168.1.102/24       management-controller-2
hostname:configuration net interfaces> destroy igb0
This will destroy "igb0" and any networking objects exclusively built over it.

Are you sure? (Y/N) y

hostname:configuration net interfaces> cd ..
hostname:configuration net> done

配置管理接口 (CLI)

相关主题