Complete these tasks to prepare to deploy Oracle Database Appliance.
dcs-agent
, various infrastructure components, and Oracle Clusterware before deploying the appliance.Interconnect is reserved for Oracle Grid Infrastructure (GI) and Oracle Relational Database Management System (RDBMS).
Oracle GI includes Oracle Clusterware, Oracle Automatic Storage Management (Oracle ASM), and Oracle Restart. Even if you do not use Oracle Real Application Clusters (RAC), Oracle Database Appliance uses the interconnect for RAC ASM and Oracle GI.
Note:
Do not use interconnect for other applications.Connect Oracle Database Appliance X7-2-HA to either a 10GBase-T (copper) or 25GbE SFP+ (fiber) network.
For 10GBase-T public networking, use the Cat-6 network cables. To use the SFP28 ports, use the correct transceivers and cables to meet your switch bandwidth. The following sections show the cabling options for 25GbE SFP+ (fiber) network ports. In the figures, callouts 4 and 5 identify the ports for the 10GBase-T (copper) network. Callout 6 identifies the ports for the 25GbE SFP+ (fiber) network.
Connect the Fiber and Copper Network Cables for Oracle Database Appliance X7-2-HA
Connect the network cables for Oracle Database Appliance X7-2-HA.
Location of Network Ports and Power Cabling
Table 3-1 Location of Network Ports and Power Cabling for Oracle Database Appliance X7-2-HA
Callout Number | Description |
---|---|
1 |
Interconnect Port 25GbE p1p1 |
2 |
Interconnect Port 25GbE p1p2 |
3 |
Dark blue SAS cable between PCIe slot 2 in Node0 (SAS0) and the dark blue port in the top IO module in the storage shelf (port0) |
4 |
Light blue SAS cable between PCIe slot 3 in Node0 (SAS1) and the light blue port in the bottom IO module in the storage shelf (port0) |
5 |
Dark red SAS cable between PCIe slot 2 in Node1 (SAS1) and the dark red port in the top IO module in the storage shelf (port1) |
6 |
Light red SAS cable between PCIe slot 3 in Node1 (SAS0) and the light red port in the bottom IO module in the storage shelf (port1) |
Connect the Fiber and Copper Network Cables for Oracle Database Appliance X7-2
Table 3-2 Location of Ports and Power Cabling for Oracle Database Appliance
Callout Number | Description |
---|---|
1 |
Power cables to the power supply unit (PSU) |
2 |
ILOM NET MGT port. Service processor 10/100/1000Base-T network interface |
3 |
(Optional) ILOM SER MGT port. Service processor RJ-45 serial port |
4 |
10 GbE network interface port with RJ-45 connector (btbond1) |
5 |
(Optional) 25 GbE dual-rate SFP+ (fiber network) ports (btbond1) |
Fiber Cables
For optical cables, you must purchase either Short Range (SR) or Long Range (LR) SFP transceivers for each of the network ports, and then plug in the appropriate optical cable. Currently, Oracle sells both the SR and LR SFP transceivers. In addition to these transceivers, you must purchase the appropriate LC-LC terminated fiber optic cables from a third-party vendor.
Table 3-3 Transceivers for the SFP Ports - 10GB/1GB
Name | Part Number |
---|---|
10Gbps Dual Rate SFP SR Transceiver |
2129A |
10Gbps SFP LR Transceiver |
5562A-Z |
Table 3-4 Transceivers for the SFP Ports - 25GB
Name | Part Number |
---|---|
SFP short range Transceiver |
7118017 |
SFP long range Transceiver |
7118020 |
Copper Cables
You can purchase the following copper cables from Oracle. These cables have built-in SFP connectors.
Table 3-5 Networking Cables for the SFP Ports - 10GB/1GB
Name | Length | Part Number |
---|---|---|
TwinAx passive copper cable: 1 meter |
1m |
7105137 |
TwinAx passive copper cable: 3 meter |
3m |
7105140 |
TwinAx passive copper cable: 5 meter |
5m |
7151141 |
Table 3-6 Networking Cables for the SFP Ports - 25GB
Name | Length | Part Number |
---|---|---|
Copper splitter cable assembly: 1 meter QSFP28 to 4 SFP28 |
1m |
7118355 |
Copper splitter cable assembly: 2 meter QSFP28 to 4 SFP28 |
2m |
7118356 |
Copper splitter cable assembly: 3 meter QSFP28 to 4 SFP28 |
3m |
7118357 |
Copper splitter cable assembly: 5 meter QSFP28 to 4 SFP28 |
5m |
7118358 |
TwinAx passive copper cable: 1 meter |
1m |
7118359 |
TwinAx passive copper cable: 3 meter |
2m |
7118360 |
TwinAx passive copper cable: 5 meter |
3m |
7118361 |
TwinAx passive copper cable: 5 meter |
5m |
7118362 |
Connect Oracle Database Appliance X7-2S or X7-2M to either a 10GBase-T (copper) or 25GbE SFP+ (fiber) network.
Use standard Cat-6 network cables to connect to the on-board 10GBase-T (copper) network ports. The following sections show the cabling options for 25GbE SFP+ (fiber) network ports. In the figures, callout 4 identifies the ports for the 10GBase-T (copper) network and callout 5 identifies the ports for the 25GbE SFP28 (fiber) network.
Connect the Fiber and Copper Network Cables for Oracle Database Appliance X7-2S or X7-2M
Connect the Fiber and Copper Network Cables for Oracle Database Appliance X7-2S or X7-2M
Location of Network Ports and Power Cabling
Table 3-7 Location of Network Ports and Power Cabling for Oracle Database Appliance
Callout Number | Description |
---|---|
1 |
Power cables to the power supply unit (PSU) |
2 |
ILOM NET MGT port. Service processor 10/100/1000Base-T network interface |
3 |
(Optional) ILOM SER MGT port. Service processor RJ-45 serial port |
4 |
10 GbE network interface port with RJ-45 connector (btbond1) |
5 |
(Optional) 25 GbE dual-rate SFP+ (fiber network) ports (btbond1) |
Fiber Cables
For optical cables, you must purchase either Short Range (SR) or Long Range (LR) SFP transceivers for each of the network ports, and then plug in the appropriate optical cable. Currently, Oracle sells both the SR and LR SFP transceivers. In addition to these transceivers, you must purchase the appropriate LC-LC terminated fiber optic cables from a third-party vendor.
Name | Part Number |
---|---|
10Gbps Dual Rate SFP SR Transceiver |
2129A |
10Gbps SFP LR Transceiver |
5562A-Z |
Copper Cables
You can purchase the following copper cables from Oracle. These cables have built-in SFP connectors:
Name | Length | Part Number |
---|---|---|
TwinAx passive copper cable: 1m |
1m |
7105137 |
TwinAx passive copper cable: 3m |
3m |
7105140 |
TwinAx passive copper cable: 5m |
5m |
7151141 |
Complete this task if you have direct access to Oracle Database Appliance and you intend to use a locally connected monitor, keyboard and mouse.
Oracle Database Appliance is not equipped with human-computer interface devices, such as a monitor or keyboard. To log in locally, instead of through a network, you must attach interface devices to a USB port. Oracle Database Appliance X7 hardware has one USB port per server node. The hardware does not have any VGA ports. Use a USB port expansion card or hub to attach more than one peripheral.
Use this procedure to start up either a newly-installed Oracle Database Appliance, or to start up the appliance after you power it down.
To ready Oracle Database Appliance for the powering on the first time, you need to attach all of the required power cords and confirm that initialization completes successfully. You can then start up the system by pushing the power button once.
Attach power cords for Oracle Database Appliance.
Caution:
Before plugging in the power cords, ensure that the electrical outlets providing the power are grounded.If you use only a single AC circuit, then connect both power cords for each component to that circuit. If you want to maintain N+1 power supply redundancy, then use two separate AC circuits. Connect one power cord from each AC circuit into each component.
For more information about cabling with the supplied Cable Management Arm, refer to Oracle Database Appliance Owner’s Guide.
Use this procedure the first time you power on Oracle Database Appliance.
When you power on Oracle Database Appliance for the first time, the system automatically defines your public network interface based on which of the public interface ports are connected. The onboard 10GBase-T (Copper) ports are used for the interconnect.
Note:
After you connect power cords, the green SP OK light-emitting diode (LED) lights blink for a few minutes, and then turn to steady ON. The cooling fans also may turn on. However, these events do not indicate that the system is started. You must complete all of the steps in this section to turn on the appliance properly. Read through the entire section to understand the sequence required for initial system startup.Configure Oracle Integrated Lights Out Manager (Oracle ILOM) to manage Oracle Database Appliance independent of the operating system.
Oracle ILOM provides alternate ways to restart and troubleshoot Oracle Database Appliance.
You must set up the following items first to configure Oracle ILOM:
A name and IP address
A password to replace the default Oracle ILOM password
Access to a management network, using an assigned netmask
An Ethernet cable connected from the NET MGT port to the management network
In the default configuration, Dynamic Host Configuration Protocol (DHCP) is enabled in Oracle ILOM and the DHCP server automatically assigns network settings. To determine the IP address or host name assigned by the DHCP server, use the network tools provided with the DHCP server.
If you do not use DHCP, then use the custom option in Oracle Database Appliance Manager Configurator to assign IP addresses and host names to Oracle ILOM when you deploy your database.
Note:
If you have not enabled DHCP, then you must complete Oracle Database Appliance configuration to access Oracle ILOM.
To connect to the Oracle ILOM, use one of the following two methods:
Log in using a web interface by completing these steps:
Using a client system's browser, enter the IP address or host name assigned by DHCP into the browser address field and press Enter.
At the login page, enter the default user name, root
and the default password, changeme
.
The Oracle ILOM web interface appears.
Log in using a command-line interface (CLI) by completing these steps:
Using a client system, establish a secure shell (SSH) connection by entering the following on the command line:
ssh -l root sp_ip_address
where sp_ip_address
is the IP address assigned by DHCP.
Enter the default user name, root
, and the default password, changeme
.
The Oracle ILOM CLI prompt appears.
Troubleshooting the ILOM Configuration
If the ILOM is not working, then ensure that the ILOM NIC is enabled and that ipv4
is enabled.
You can configure the ILOM with the IPMI tool or through the BIOS. The following describes how to use the IPMI tool:
Open the IPMI tool.
# ipmitool –I open sunoem cli
Go to SP/network
and verify that the port is enabled:
cd /SP/network
If the port is not enabled, then enable the port.
set state=enabled
In SP/network
, verify that ipv4
is enabled.
If ipv6
is enabled, then disable ipv6
and enable ipv4
# ipmitool -I open sunoem cli "set /SP/network/ipv6 state=disabled" # ipmitool -I open sunoem cli "set /SP/network/ipv4 state=enabled"
Configure a temporary network configuration framework to build your network information during deployment.
Use either the 10GBase-T or the 25GbE SFP+ network interface. Use the initial network connection to transfer deployment software to Oracle Database Appliance and deploy the appliance with the Web Console.
Caution:
Oracle recommends using the configure-firstnet
command only one time on Oracle Database Appliance. Subsequent use after configuring the initial network can cause unpredictable changes to your network settings.
Related Topics
Use the Server patch to update the dcs-agent
, various infrastructure components, and Oracle Clusterware before deploying the appliance.
If the system is Oracle Database Appliance X7-2-HA, you must update the repository, and run the update commands on both nodes.
The patches are available for download in My Oracle Support. You must download the server patch to an external client and then copy the files from the external client to a /tmp
directory on the appliance. In some cases, there might not be sufficient space in the /tmp
directory. Consider creating a /tmp
directory in the /u01
directory.
Copy the file using a Secure Copy (scp
) or Secure File Transfer Protocol (sftp
) protocol. To use scp
or sftp
, you must first set up a static IP address (for example, oda_host
) and configure Oracle Database Appliance with that address by using the configure-firstnet
command. This command ensures the system is available in your network, enabling you to use the Oracle Appliance Manager Web Console to deploy Oracle Database Appliance.
Alternatively, you can use a USB storage device. To use a USB drive to transfer the files, you must format it first as FAT32
, ext3
, or ext4
. NTFS file formats are not supported.
Related Topics
Download the Oracle Database Appliance GI and RDBMS Software Clone Files from My Oracle Support and update the patch repository.
Update the patch repository with the following patch files:
GI Clone: The patch contains the latest Grid Infrastructure components needed to deploy, or create, an Oracle Database Appliance.
RDBMS Software Clone file: Release-specific database clone files contain the components needed to create database homes and databases in Oracle Database Appliance. RDBMS Software is available for Oracle Database 12.2.0.1, 12.1.0.2, and 11.2.0.4.
The patches are available for download in My Oracle Support. You must download the GI and DB software files to an external client and then copy the files from the external client to a /tmp
directory on the appliance. In some cases, there might not be sufficient space in the /tmp
directory. Consider creating a /tmp
directory in the /u01
directory.
Copy the file using a Secure Copy (scp
) or Secure File Transfer Protocol (sftp
) protocol. To use scp
or sftp
, you must first set up a static IP address (for example, oda_host
) and configure Oracle Database Appliance with that address by using the configure-firstnet
command. This command ensures the system is available in your network, enabling you to use the Oracle Appliance Manager Web Console to deploy Oracle Database Appliance.
Alternatively, you can use a USB storage device. To use a USB drive to transfer the files, you must format it first as FAT32
, ext3
, or ext4
. NTFS file formats are not supported.
Note:
Ensure that the server components are updated before you update the patch repository with the GI Clone and RDBMS Software Clone files. If the system is Oracle Database Appliance X7-2-HA, you must update both nodes.
Related Topics