Changing the DPC Quantity

This procedure is used to increase the number of DPCs that are allowed in the EAGLE beyond what is currently shown in the ent-dstn, dlt-dstn, chg-dstn, and rtrv-dstn outputs. The EAGLE can contain a maximum of one of these quantities: 2000 (system default), 5000, 6000, 7000, 8000, or 10,000 DPCs.

To have more than 2000 DPCs in the EAGLE, the 5000 Routes feature must be turned on using the chg-feat command. Turning on the 5000 Routes features allows the EAGLE to contain a maximum of 5000 DPCs. To have more than 5000 DPCs in the EAGLE, either 6000, 7000, or 8000, or 10,000 routesets must be enabled using the enable-ctrl-feat command, in addition to having the 5000 Routes feature turned on. Enabling 6000, 7000, 8000, or 10,000 routesets allows the EAGLE to contain a maximum of 6000, 7000, 8000, or 10,000 DPCs. The rtrv-ctrl-feat command shows whether or not 6000, 7000, 8000, or 10,000 routesets are enabled. The rtrv-feat command shows whether or not the 5000 Routes feature is turned on.

Note:

Once the 5000 Routes feature is turned on with the chg-feat command, it cannot be turned off.

The 5000 Routes feature must be purchased before you turn this feature on with the chg-feat command. If you are not sure if you have purchased the 5000 Routes feature, contact your Oracle Sales Representative or Account Representative.

Once the maximum DPC quantity is set, the actual number of DPCs allowed in the EAGLE is configured using the mtpdpcq parameter of the chg-stpopts command. The rtrv-stpopts command output, as well as the outputs of the ent-dstn, dlt-dstn, chg-dstn, and rtrv-dstn commands, shows the actual number of DPCs allowed in the EAGLE.

If the Cluster Routing and Management Diversity feature is turned on, (shown by the entry CRMD = on in the rtrv-feat output) the mtpxlq parameter is also shown in the rtrv-stpopts output. The mtpxlq parameter defines the maximum number of entries that the exception list (x-list) for the Cluster Routing and Management Diversity feature can contain. The value of the mtpxlq parameter of the chg-stpopts command can also be changed to more than 2000 destination point codes. For more information on exception lists, see the "Exception Lists (X-lists)" in the Cluster Routing and Management Diversity (CRMD) section.

The enable-ctrl-feat command enables 6000, 7000, 8000, or 10,000 routesets by inputting the part number for the routeset quantity and the routeset quantity’s feature access key with these parameters.

:partnum – The Oracle-issued part number for the routeset quantity:

• For 6000 routesets - 893006401
• For 7000 routesets - 893006402
• For 8000 routesets - 893006403
• For 10,000 routesets - 893006405

:fak – The feature access key supplied by Oracle. The feature access key contains 13 alphanumeric characters and is not case sensitive.

Note:

The values for the feature access key (the fak parameter) are provided by Oracle. If you do not have the feature access key for the routeset quantity you wish to enable, contact your Oracle Sales Representative or Account Representative.

The enable-ctrl-feat command requires a valid serial number for the EAGLE to be configured in the database, and that this serial number is locked. This can be verified with the rtrv-serial-num command. The EAGLE is shipped with a serial number in the database, but the serial number is not locked. The serial number can be changed, if necessary, and locked once the EAGLE is on-site, by using the ent-serial-num command. The ent-serial-num command uses these parameters.

:serial – The serial number assigned to the EAGLE. The serial number is not case sensitive.

:lock – Specifies whether or not the serial number is locked. This parameter has only one value, yes, which locks the serial number. Once the serial number is locked, it cannot be changed.

Note:

To enter and lock the EAGLE’s serial number, the ent-serial-num command must be entered twice, once to add the correct serial number to the database with the serial parameter, then again with the serial and the lock=yes parameters to lock the serial number. You should verify that the serial number in the database is correct before locking the serial number. The serial number can be found on a label affixed to the control shelf (shelf 1100).

To enable 7000 or 8000 routesets, the DPC table can contain no more than 8000 alias point codes. To enable 10,000 routesets, the DPC table can contain no more than 10,000 alias point codes. The number of alias point codes configured in the EAGLE is shown in the output of the ent-dstn, dlt-dstn, chg-dstn, and rtrv-dstn command outputs in one of two ways, depending on whether or not the Cluster Routing and Management Diversity feature is on or off.

If the Cluster Routing and Management Diversity feature is off.

rlghncxa03w 07-05-17 16:02:05 GMT  EAGLE5 37.0.0
Destination table is (10 of 8000) 1% full
Alias table is (8 of 8000) 1% full
RTRV-DSTN: MASP A - COMPLTD

If the Cluster Routing and Management Diversity feature is on.

rlghncxa03w 07-05-17 16:02:05 GMT  EAGLE5 37.0.0
DESTINATION ENTRIES ALLOCATED:   8000
    FULL DPC(s):                    9
    EXCEPTION DPC(s):               0
    NETWORK DPC(s):                 0
    CLUSTER DPC(s):                 1
    TOTAL DPC(s):                  10
    CAPACITY (% FULL):             1%
ALIASES ALLOCATED:               8000
    ALIASES USED:                   8
    CAPACITY (% FULL):             1%
X-LIST ENTRIES ALLOCATED:         500
RTRV-DSTN: MASP A - COMPLTD

To set the alias point code quantity below 8000 if 7000 or 8000 routesets will be enabled, or 10,000 if 10,000 routesets will be enabled, perform the Changing a Destination Point Code procedure. The alias point codes are removed using this procedure.

The routeset quantities (6000, 7000, 8000, or 10,000) cannot be temporarily enabled (with a temporary feature access key) and cannot be disabled with the chg-ctrl-feat command and the status=off parameter. The routeset quantity cannot be decreased to a smaller quantity once a quantity is enabled. For example, if the current routeset quantity of the EAGLE is 7000 routesets, the quantity cannot be reduced to 6000 routesets.

Once any of these routeset quantities are enabled with the enable-ctrl-feat command, they are also activated. The chg-ctrl-feat command is not necessary to activate these routeset quantities.

To enable 10,000 routesets, the EAGLE can contain only E5-based control cards. Refer to Maintenance and Administration Subsystem for more information about the control cards.

1. Display the DPC quantity currently allowed in the EAGLE by entering the rtrv-stpopts command.

   The DPC quantity is displayed in the MTPDPCQ field of the output. This is an example of the possible output.

   rlghncxa03w 07-05-17 16:02:05 GMT  EAGLE5 37.0.0
   STP OPTIONS
   -----------------------
   MTPDPCQ           1750
   

   Note:

   The rtrv-stpopts command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by the rtrv-stpopts command, see the rtrv-stpopts command description in Commands User's Guide.

   The MTPDPCQ value cannot exceed one of these totals depending on the features that are enabled or turned on.

   • 2000 – if the 5000 Routes feature is not on, and 6000, 7000, 8000, or 10,000 routesets are not enabled.
   • 5000 – if the 5000 Routes feature is on, and 6000, 7000, 8000, or 10,000 routesets are not enabled.
   • 6000 – if 6000 routesets are enabled.
   • 7000 – if 7000 routesets are enabled.
   • 8000 – if 8000 routesets are enabled.
   • 10,000 – if 10,000 routesets are enabled.

   If the Cluster Routing and Management Diversity feature is on, the MTPXLQ field will be shown in the rtrv-stpopts command output. The MTPXLQ field shows the maximum number of entries the exception list (x-list) can contain. The sum of the MTPDPCQ and MTPXLQ values cannot exceed one of these totals depending on the features that are enabled or turned on.

   • 2500 – if the 5000 Routes feature is not on, and 6000, 7000, 8000, or 10,000 routesets are not enabled.
   • 5500 – if the 5000 Routes feature is on, and 6000, 7000, 8000, or 10,000 routesets are not enabled.
   • 6500 – if 6000 routesets are enabled.
   • 7500 – if 7000 routesets are enabled.
   • 8500 – if 8000 routesets are enabled.
   • 10,500 – if 10,000 routesets are enabled.

   For more information on the Cluster Routing and Management Diversity feature, see the Cluster Routing and Management Diversity (CRMD) section.

   Perform one of the following steps based on the MTPDPCQ value (or MTPDPCQ and MTPXLQ values) shown in the rtrv-stpopts output. The values shown in parentheses are the sum of the MTPDPCQ and MTPXLQ values.

   • 8001 - 10,000 (8501 - 10,500) – 10,000 routesets are enabled. The only action that can be performed is to change the DPC quantity using the chg-stpopts command. This is the maximum number of routesets the EAGLE can have. Continue the procedure with 14 to change the DPC quantity. If you do not wish to change the DPC quantity, this procedure is finished.
   • 7001 - 8000 (7501 - 8500) – 8000 routesets are enabled. To enable the 10,000 routeset quantity, continue the procedure with 11. If you wish to change the DPC quantity and not enable 10,000 routesets, continue the procedure with 14. If you do not wish to enable 10,000 routesets or change the DPC quantity, this procedure is finished.
   • 6001 - 7000 (6501 - 7500) – 7000 routesets are enabled. To enable the 8000 routeset quantity, continue the procedure with Oracle. To enable the 10,000 routeset quantity, continue the procedure with 11. If you wish to change the DPC quantity and not enable 8000 or 10,000 routesets, continue the procedure with 14. If you do not wish to enable 8000 or 10,000 routesets or change the DPC quantity, this procedure is finished.
   • 5001 - 6000 (5501 - 6500) – 6000 routesets are enabled. To enable 7000, or 8000, 10,000 routesets, continue the procedure with 10. To enable the 10,000 routeset quantity, continue the procedure with 11. If you wish to change the DPC quantity and not enable 7000, 8000, or 10,000 routesets, continue the procedure with 14. If you do not wish to enable 7000, 8000, or 10,000 routesets or change the DPC quantity, this procedure is finished.
   • 2001 - 5000 (2501 - 5500) – The 5000 Routes feature is on. To enable 6000, 7000, 8000, or 10,000 routesets, perform 2. If you wish to change the DPC quantity and not enable 6000, 7000, 8000, or 10,000 routesets, continue the procedure with 14. If you do not wish to enable 6000, 7000, 8000, or 10,000 routesets or change the DPC quantity, this procedure is finished.
   • 2000 or less (2500 or less) – Continue the procedure with 2.
2. Verify that 6000, 7000, 8000, or 10,000 routesets are enabled by entering the rtrv-ctrl-featcommand.

   The following is an example of the possible output.

   rlghncxa03w 07-05-28 21:15:37 GMT EAGLE5 37.0.0
   The following features have been permanently enabled:
   
   Feature Name              Partnum    Status  Quantity
   Command Class Management  893005801  on      ----
   LNP Short Message Service 893006601  on      ----
   Intermed GTT Load Sharing 893006901  on      ----
   XGTT Table Expansion      893006101  on      4000000
   XMAP Table Expansion      893007710  on      3000
   Large System # Links      893005901  on      1500
   Routesets                 893006401  on      6000
   HC-MIM SLK Capacity       893012707  on      64
   
   The following features have been temporarily enabled:
   
   Feature Name              Partnum   Status  Quantity     Trial Period Left
   Zero entries found.
   
   The following features have expired temporary keys:
   
   Feature Name              Partnum
   Zero entries found.
   

   If 10,000 routesets are enabled, the Routesets row appears in the rtrv-ctrl-feat output with a quantity of 10,000. The only action that can be performed is to change the DPC quantity using the chg-stpopts command. This is the maximum number of routesets the EAGLE can have. Continue the procedure with 14 to change the DPC quantity. If you do not wish to change the DPC quantity, this procedure is finished.

   If 8000 routesets are enabled, the Routesets row appears in the rtrv-ctrl-feat output with a quantity of 8000. To enable 10,000 routesets, continue the procedure with 11. If you wish to change the DPC quantity and not enable 10,000 routesets, continue the procedure with 14. If you do not wish to enable 10,000 routesets or change the DPC quantity, this procedure is finished.

   If 7000 routesets are enabled, the Routesets row appears in the rtrv-ctrl-feat output with a quantity of 7000. To enable 8000 routesets, continue the procedure with Oracle. To enable 10,000 routesets, continue the procedure with 11. If you wish to change the DPC quantity and not enable 8000 or 10,000 routesets, continue the procedure with 14. If you do not wish to enable 8000 or 10,000 routesets or change the DPC quantity, this procedure is finished.

   If 6000 routesets are enabled, the Routesets row appears in the rtrv-ctrl-feat output with a quantity of 6000. To enable 7000 or 8000, 8000, or 10,000 routesets, continue the procedure with 10. To enable 10,000 routesets, continue the procedure with 11. If you wish to change the DPC quantity and not enable 7000, 8000, or 10,000 routesets, continue the procedure with 14. If you do not wish to enable 7000, 8000, or 10,000 routesets or change the DPC quantity, this procedure is finished.

   If 6000, 7000, 8000, or 10,000 routesets are not enabled, continue the procedure with 3.

3. Enter the rtrv-feat command to verify that the 5000 Routes feature is turned on.

   If the 5000 Routes feature is on, the DSTN5000 = on entry appears in the output.

   Note:

   The rtrv-feat command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by the rtrv-feat command, see the rtrv-feat command description in the Commands Manual.

   If the 5000 Routes feature is not on, and you do not wish to turn the 5000 Routes feature on, or enable 6000, 7000, 8000, or 10,000 routesets, the only action that can be performed is to change the DPC quantity using the chg-stpopts command. However the DPC quantity can be no greater than 2000 DPCs (2500 DPCs if the rtrv-stpopts output in 1 contains the MTPDPCQ and MTPXLQ parameters). Continue the procedure with 14 to change the DPC quantity. If you do not wish to change the DPC quantity, this procedure is finished.

   If the 5000 Routes feature is not on, and you wish to turn the 5000 Routes feature on, or enable 6000, 7000, 8000, or 10,000 routesets, continue the procedure with 4.

   If the 5000 Routes feature is on, continue the procedure with 6.

4. Turn the 5000 Routes feature on by entering this command.

   chg-feat:DSTN5000=on

   Note:

   Once the 5000 Routes feature is turned on with the chg-feat command, it cannot be turned off.

   The 5000 Routes feature must be purchased before you turn this feature on with the chg-feat command. If you are not sure if you have purchased the 5000 Routes feature, contact your Oracle Sales Representative or Account Representative.

   When the chg-feat has successfully completed, this message appears.

   rlghncxa03w 07-05-28 11:43:04 GMT EAGLE5 37.0.0
   CHG-FEAT: MASP A - COMPLTD
   

5. Verify that the 5000 Routes feature is turned on, by entering the rtrv-feat command.

   If the 5000 Routes feature is on, the DSTN5000 = on appears in the command output.

   Note:

   The rtrv-feat command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by the rtrv-feat command, see the rtrv-feat command description in Commands User's Guide.

   If 6000, 7000, 8000, or 10,000 routesets are not being enabled, the only action that can be performed is to change the DPC quantity. If you wish to change the DPC quantity and not enable 6000, 7000, 8000, or 10,000 routesets, continue the procedure with 14. If you do not wish to enable 6000, 7000, 8000, or 10,000 routesets or change the DPC quantity, this procedure is finished.

   If 6000, 7000, 8000, or 10,000 routesets are being enabled, go to 6.

   Note:

   If the rtrv-ctrl-feat output in 1 shows any controlled features, continue the procedure 10. If the rtrv-ctrl-feat output shows only the HC-MIM SLK Capacity feature with a quantity of 64, 6 through 9 must be performed.

   If 6000, 7000, 8000, or 10,000 routesets are being enabled, the serial number of the EAGLE must be in the database and the serial number must be locked. If the rtrv-ctrl-feat output in 2 shows any features in addition to the HC-MIM SLK Capacity feature with a quantity of 64, the serial number is in the database and it is locked. Continue the procedure by performing one of these steps.

   • If 6000 routesets are being enabled, continue the procedure with Oracle.
   • If 7000, 8000, or 10,000 routesets are being enabled, continue the procedure with 10.

   The HC-MIM SLK Capacity feature with a quantity of 64 is shown in the rtrv-ctrl-feat output in 2 whether or not the serial number of the EAGLE is in the database or whether or not the serial number is locked. If the rtrv-ctrl-feat output shows only the HC-MIM SLK Capacity feature with a quantity of 64, the status of the serial number must be verified. Continue the procedure with 6.

6. Display the serial number in the database with the rtrv-serial-num command.

   This is an example of the possible output.

   rlghncxa03w 07-05-28 21:15:37 GMT EAGLE5 37.0.0
   System serial number = nt00001231
   System serial number is not locked.
   rlghncxa03w 07-10-28 21:15:37 GMT EAGLE5 37.0.0
   Command Completed
   

   Note:

   If the serial number is correct and locked, continue the procedure with Oracle if 6000 routesets are being enabled. Continue the procedure with 10 if 7000, 8000, or 10,000 routesets are being enabled. If the serial number is correct but not locked, continue the procedure with 9. If the serial number is not correct, but is locked, 6000, 7000, 8000, or 10,000 routesets cannot be enabled and the remainder of this procedure cannot be performed. Contact the Customer Care Center to get an incorrect and locked serial number changed. Refer to the My Oracle Support (MOS) section for the contact information. The serial number can be found on a label affixed to the control shelf (shelf 1100).
7. Enter the correct serial number into the database using the ent-serial-num command with the serial parameter.

   For this example, enter this command.

   ent-serial-num:serial=<EAGLE’s correct serial number>

   When this command has successfully completed, the following message should appear.

   rlghncxa03w 07-05-28 21:15:37 GMT EAGLE5 37.0.0
   ENT-SERIAL-NUM:  MASP A - COMPLTD
   

8. Verify that the serial number entered in 7 was entered correctly using the rtrv-serial-num command.

   This is an example of the possible output.

   rlghncxa03w 07-05-28 21:15:37 GMT EAGLE5 37.0.0
   System serial number = nt00001231
   System serial number is not locked.
   rlghncxa03w 07-05-28 21:15:37 GMT EAGLE5 37.0.0
   Command Completed
   

   If the serial number was not entered correctly, repeat 7 and 8 and re-enter the correct serial number.

9. Lock the serial number in the database by entering the ent-serial-num command with the serial number shown in 6, if the serial number shown in 6 is correct, or with the serial number shown in 8, if the serial number was changed in 7, and with the lock=yes parameter.

   For this example, enter this command.

   ent-serial-num:serial=<EAGLE’s serial number>:lock=yes

   When this command has successfully completed, the following message should appear.

   rlghncxa03w 07-05-28 21:15:37 GMT EAGLE5 37.0.0
   ENT-SERIAL-NUM:  MASP A - COMPLTD
   

   If 6000 routesets are not being enabled, continue the procedure with Oracle.

   If 7000, 8000, or 10,000 routesets are not being enabled, continue the procedure with Oracle.

   If 7000 routesets are currently enabled, and 8000 or 10,000 routesets are being enabled, continue the procedure with Oracle.

   If 5000 or 6000 routesets are currently enabled and 7000, 8000, or 10,000 routesets are being enabled, continue the procedure with 10.

10. Verify the number of alias point codes configured in the EAGLE by entering the rtrv-dstn command with the msar=only parameter.

    To enable 7000 or 8000 routesets, the EAGLE can have no more than 8000 alias point codes.

    To enable 10,000 routesets, the EAGLE can have no more than 10,000 alias point codes.

    The msar=only parameter displays only the maximum numbers of different types of point codes the EAGLE can have and the actual numbers of the different types of point codes that are configured in the EAGLE.

    rtrv-dstn:msar=only

    One of two types of outputs are displayed, depending on whether or not the Cluster Routing and Management Diversity feature is on or off.

    If the Cluster Routing and Management Diversity feature is off:

    rlghncxa03w 07-05-17 16:02:05 GMT  EAGLE5 37.0.0
    Destination table is (10 of 8000) 1% full
    Alias table is (8 of 8000) 1% full
    RTRV-DSTN: MASP A - COMPLTD
    

    If the Cluster Routing and Management Diversity feature is on:

    rlghncxa03w 07-05-17 16:02:05 GMT  EAGLE5 37.0.0
    DESTINATION ENTRIES ALLOCATED:   8000
        FULL DPC(s):                    9
        EXCEPTION DPC(s):               0
        NETWORK DPC(s):                 0
        CLUSTER DPC(s):                 1
        TOTAL DPC(s):                  10
        CAPACITY (% FULL):             1%
    ALIASES ALLOCATED:               8000
        ALIASES USED:                   8
        CAPACITY (% FULL):             1%
    X-LIST ENTRIES ALLOCATED:         500
    RTRV-DSTN: MASP A - COMPLTD
    

    If 7000 or 8000 routesets are being enabled and the EAGLE contains more than 8000 alias point codes, perform the Changing a Destination Point Code procedure to reduce the number of alias point codes to an amount below 8000.

    If 10,000 routesets are being enabled and the EAGLE contains more than 10,000 alias point codes, perform the Changing a Destination Point Code procedure to reduce the number of alias point codes to an amount below 10,000.

    When this step has been completed, continue the procedure by performing one of these steps.

    • If 7000 or 8000 routesets are being enabled, continue the procedure with Oracle.
    • If 10,000 routesets are being enabled, continue the procedure with 11.
11. Display the control cards in the EAGLE by entering this command.

    rtrv-stp:gpl=oamhc

    This is an example of the possible output.

    rlghncxa03w 10-12-01 16:07:48 GMT  EAGLE5 43.0.0
    
    Card  Part Number  Rev Serial Number  Type     DB     APPL     GPL Version
    ----  -----------  --- -------------  ----     --     ----     -----------
    1113  870-2903-01  C   10206255064    E5MCAP   1024M  OAMHC    132-018-000
    1115  870-2903-01  C   10206255165    E5MCAP   1024M  OAMHC    132-018-000
    
    Command Completed.
    

    To enable 10,000 routesets, E5-MCAP cards must be installed in card locations 1113 and 1115. If E5-MCAP cards are not shown in either card location 1113 or 1115, install the E5-MCAP cards in card locations 1113 or 1115 as required. Contact the Customer Care Center before installing the E5-MCAP cards. Refer to the My Oracle Support (MOS) section for the contact information.

    After the E5-MCAP cards have been installed, or if E5-MCAP cards are shown in card locations 1113 and 1115 in the rtrv-stp output, continue the procedure with Oracle.

12. Enable the routeset quantity with the enable-ctrl-feat command specifying the part number for the routeset quantity and the feature access key.
    • To enable 6000 routesets, enter this command.

      enable-ctrl-feat:partnum=893006401:fak=<6000 Routesets feature access key>

    • To enable 7000 routesets, enter this command.

      enable-ctrl-feat:partnum=893006402:fak=<7000 Routesets feature access key>

    • To enable 8000 routesets, enter this command.

      enable-ctrl-feat:partnum=893006403:fak=<8000 Routesets feature access key>

    • To enable 10,000 routesets, enter this command.

      enable-ctrl-feat:partnum=893006405:fak=<10,000 Routesets feature access key>

    Note:

    A temporary feature access key cannot be specified to enable the routeset quantity.

    Note:

    The values for the feature access key (the fak parameter) are provided by Oracle. If you do not have the feature access key for the routeset quantity you wish to enable, contact your Oracle Sales Representative or Account Representative.

    When the enable-ctrl-feat command has successfully completed, this message should appear.

    rlghncxa03w 07-05-28 21:15:37 GMT EAGLE5 37.0.0
    ENABLE-CTRL-FEAT: MASP B - COMPLTD
    

13. Verify the changes by entering the rtrv-ctrl-featcommand with the routeset quantity part number specified in Oracle.
    • If 6000 routesets was enabled, enter this command.

      rtrv-ctrl-feat:partnum=893006401

      The following is an example of the possible output.

      rlghncxa03w 07-05-28 21:15:37 GMT EAGLE5 37.0.0
      The following features have been permanently enabled:
      
      Feature Name              Partnum    Status  Quantity
      Routesets                 893006401  on      6000
      
      The following features have been temporarily enabled:
      
      Feature Name              Partnum    Status  Quantity     Trial Period Left
      Zero entries found.
      
      The following features have expired temporary keys:
      
      Feature Name              Partnum
      Zero entries found.
      

    • If 7000 routesets was enabled, enter this command.

      rtrv-ctrl-feat:partnum=893006402

      The following is an example of the possible output.

      rlghncxa03w 07-05-28 21:15:37 GMT EAGLE5 37.0.0
      The following features have been permanently enabled:
      
      Feature Name              Partnum    Status  Quantity
      Routesets                 893006402  on      7000
      
      The following features have been temporarily enabled:
      
      Feature Name              Partnum    Status  Quantity     Trial Period Left
      Zero entries found.
      
      The following features have expired temporary keys:
      
      Feature Name              Partnum
      Zero entries found.
      

    • If 8000 routesets was enabled, enter this command.

      rtrv-ctrl-feat:partnum=893006403

      The following is an example of the possible output.

      rlghncxa03w 07-05-28 21:15:37 GMT EAGLE5 37.0.0
      The following features have been permanently enabled:
      
      Feature Name              Partnum    Status  Quantity
      Routesets                 893006403  on      8000
      
      The following features have been temporarily enabled:
      
      Feature Name              Partnum    Status  Quantity     Trial Period Left
      Zero entries found.
      
      The following features have expired temporary keys:
      
      Feature Name              Partnum
      Zero entries found.
      

    • If 10,000 routesets was enabled, enter this command.

      rtrv-ctrl-feat:partnum=893006405

      The following is an example of the possible output.

      rlghncxa03w 10-12-28 21:15:37 GMT EAGLE5 42.0.0
      The following features have been permanently enabled:
      
      Feature Name              Partnum    Status  Quantity
      Routesets                 893006405  on      10000
      
      The following features have been temporarily enabled:
      
      Feature Name              Partnum    Status  Quantity     Trial Period Left
      Zero entries found.
      
      The following features have expired temporary keys:
      
      Feature Name              Partnum
      Zero entries found.
      

    Continue the procedure by performing one of these steps.

    • If the DPC quantity or exception list quantity are not being changed, continue the procedure with 16.
    • If the DPC quantity or exception list quantity are being changed, continue the procedure with 14.
14. Change the maximum number of destination point codes that the EAGLE can contain by entering the chg-stpopts command with the mtpdpcq parameter.
    The values that can be specified with the mtpdpcq parameter is shown in the following list.

    • 500 to 2000 – if the 5000 Routes feature is not on, and 6000, 7000, 8000, or 10,000 routesets are not enabled.
    • 500 to 5000 – if the 5000 Routes feature is on, and 6000, 7000, 8000, or 10,000 routesets are not enabled.
    • 500 to 6000 – if 6000 routesets are enabled.
    • 500 to 7000 – if 7000 routesets are enabled.
    • 500 to 8000 – if 8000 routesets are enabled.
    • 500 to 10000 – if 10000 routesets are enabled.

    For this example, enter this command.

    chg-stpopts:mtpdpcq=7350

    When this command has successfully completed, this message should appear.

    rlghncxa03w 07-05-07 00:22:57 GMT  EAGLE5 37.0.0
    CHG-STPOPTS: MASP A - COMPLTD
    

    If the MTPXLQ field (the exception list quantity) is shown in the rtrv-stpopts output in 1, and you wish to change only the MTPXLQ value, enter the chg-stpopts command with the mtpxlq parameter. For example, if you wish to change the exception list quantity to 1000 point codes, enter this command.chg-stpopts:mtpxlq=1000.

    Both the exception list quantity and the maximum of destination point codes can be changed, by entering the chg-stpopts command with both the mptdpcq and mptxlq parameters. For example, if you wish to change the exception list quantity to 1000 point codes and the maximum number of point codes to 6200, enter this command.

    chg-stpopts:mtpxlq=1000:mtpdpcq=6750

    When specifying the mtpxlq parameter with the chg-stpopts command, the resulting sum of the MTPDPCQ and MTPXLQ values cannot be greater than the values shown in the following list.

    • 2500 – if the 5000 Routes feature is not on, and 6000, 7000, 8000, or 10,000 routesets are not enabled. The range of values for the mtpdpcq and mtpxlq parameters is from 500 to 2000.
    • 5500 – if the 5000 Routes feature is on, and 6000, 7000, 8000, or 10,000 routesets are not enabled. The range of values for the mtpdpcq and mtpxlq parameters is from 500 to 5000.
    • 6500 – if 6000 routesets are enabled. The range of values for the mtpdpcq and mtpxlq parameters is from 500 to 6000.
    • 7500 – if 7000 routesets are enabled. The range of values for the mtpdpcq parameter is from 500 to 7000. The range of values for the mtpxlq parameters is from 500 to 6000.
    • 8500 – if 8000 routesets are is enabled. The range of values for the mtpdpcq parameter is from 500 to 8000. The range of values for the mtpxlq parameters is from 500 to 6000.
    • 10500500 to 10500 – if 10000 routesets are enabled. The range of values for the mtpdpcq and mtpxlq parameters is from 500 to 10,000.
15. Verify the changes using the rtrv-stpopts command.

    This is an example of the possible output.

    rlghncxa03w 07-05-17 16:02:05 GMT  EAGLE5 37.0.0
    STP OPTIONS
    -----------------------
    MTPDPCQ           7350
    

    Note:

    The rtrv-stpopts command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by the rtrv-stpopts command, see the rtrv-stpopts command description in the Commands Manual.

    If the mtpxlq parameter was specified in 14, the mtpxlq parameter value will be shown in the MTPXLQ field of the rtrv-stpopts command output.

16. Back up the new changes, using the chg-db:action=backup:dest=fixed command.

    These messages should appear; the active Maintenance and Administration Subsystem Processor (MASP) appears first.

    BACKUP (FIXED): MASP A - Backup starts on active MASP.
    BACKUP (FIXED): MASP A - Backup on active MASP to fixed disk complete.
    BACKUP (FIXED): MASP A - Backup starts on standby MASP.
    BACKUP (FIXED): MASP A - Backup on standby MASP to fixed disk complete.
    

Figure 2-8 Changing the DPC Quantity

Sheet 1 of 8

Sheet 2 of 8

Sheet 3 of 8

Sheet 4 of 8

Sheet 5 of 8

Sheet 6 of 8

Sheet 7 of 8

Sheet 8 of 8