Go to primary content
Oracle® Communications EAGLE Database Administration - SS7 User's Guide
Release 46.6
E93318 Revision 1
Go To Table Of Contents
Contents

Previous
Previous
Next
Next

Adding an Exception Route Entry

This procedure is used to add an exception route to the database using the ent-rtx command. The ent-rtx command uses these parameters.

:dpc/dpca/dpci/dpcn/dpcn24 – The destination point code of the node that the traffic is being sent to.

:opc/opca/opci/opcn/opcn24 – The originating point code of the node sending traffic to the EAGLE.

Note:

See Point Code Formats for a definition of the point code types that are used on the EAGLE and for a definition of the different formats that can be used for ITU national point codes.

:ilsn – The name of the linkset carrying incoming traffic to the EAGLE.

:lsn – The name of the linkset that will carry the traffic to the node specified by the destination point code.

:si – The service indicator value that will be assigned to the exception route. The value of the si parameter is 3 to 15.

:cic – The circuit identification code (CIC) value that will be assigned to an exception route containing a single CIC entry or the CIC value that begins a range of CICs that will be assigned to the exception route. The value of the cic parameter is 0 to 16383.

:ecic – The circuit identification code value that ends the range of CICs that will be assigned to the exception route. The value of the ecic parameter is 0 to 16383.

:rc – The relative cost value (priority) that will be assigned to the exception route. The value of the rc parameter is 0 to 99.

:force – This parameter allows an exception route to be added to the database even if the ilsn parameter value is the same as the lsn parameter value. This parameter has only one value, yes.

The combinations of these parameters that can be used with the ent-rtx command are shown in Table 3-27.

To add an exception route to the database, the Origin-Based MTP Routing feature must be enabled and turned on. If error message E4584 is displayed after the rtrv-rtx command is executed, the Origin-Based MTP Routing feature is not enabled or turned on.

E4584 Cmd Rej: MTP Origin Based Routing Feature must be ON

If the Origin-Based MTP Routing feature is not enabled or turned on, perform the Activating the Origin-Based MTP Routing Feature procedure to enable, if required, and turn on the Origin-Based MTP Routing feature.

The DPC value assigned to the exception route must be assigned to a route. If the required route is not shown in the rtrv-rte output, perform on of these procedures to add the required route.

The names of the linksets required specified for the lsn and ilsn parameters must be provisioned in the database. This can be verified by entering the rtrv-ls command. If the required linkset is not in the database, perform one of these procedures to add the linkset.

  • Adding an SS7 Linkset
  • “Configuring an IPGWx Linkset,” "Adding an IPSG M2PA Linkset," or "Adding an IPSG M3UA Linkset" procedures in Database Administration - IP7 User's Guide.

The linkset must be added according to the rules shown in the "Adding Linksets for Exception Routes" section.

Adding Linksets for Exception Routes

The linkset must be added according to the following rules:

  • If the dpc value of the exception route entry is an ANSI point code, the adjacent point code of the lsn value must be an ANSI point code.
  • If the exception route is an OPC-based exception route, the opc parameter value cannot be the adjacent point code of the linkset that is specified by the lsn parameter value.
  • If the dpc value of the exception route entry is an ITU-I point code, the adjacent point code of the lsn value must be an ITU-I point code. If the linkset contains an SAPC (secondary adjacent point code), the adjacent point code of the lsn value can be either an ITU-N or ITU-N24 point code if the sapc value is an ITU-I point code. If the adjacent point code of the lsn value is an ITU-N point code with a group code, when the exception route is added, the group code of the adjacent point code of the linkset does not have to be the same as the group code of the opcn value. If an ITU-N linkset is specified for the ilsn parameter, the group code of the adjacent point code of the ilsn value does not have to match the group code of the adjacent point code of the lsn value.
  • If the dpc value of the exception route entry is an ITU-N point code, the adjacent point code of the lsn value must be an ITU-N point code.
    • If the dpc value of the exception route entry is an ITU-N point code with no group code assigned to the ITU-N point code, the adjacent point code of the lsn value or the adjacent point code of all the linksets in the routeset can be an ITU-I point code if the sapc (secondary adjacent point code) value is an ITU-N point code.
    • If the dpc value of the exception route entry is an ITU-N point code with a group code, the adjacent point code of the lsn value can be an ITU-I point code if the sapc value is an ITU-N point code. When the exception route is added, the group code of the dpcn value and the opcn value must be the same. The group code of the adjacent point code of the lsn value and the ilsn value must be the same. The group code of the dpcn value must be the same as the group code of either the adjacent point code of the lsn value or the sapc (secondary adjacent point code) assigned to the lsn value.
  • If the dpc value of the exception route entry is an ITU-N24 point code, the adjacent point code of the lsn value must be an ITU-N24 point code. If the linkset contains an SAPC (secondary adjacent point code), the adjacent point code of the lsn value can be an ITU-I point code if the sapc value is an ITU-N24 point code.

The SAPC values assigned to the linksets can be verified by entering the rtrv-ls:lsn=<linkset name> command.

  1. Display the exception routes in the database by entering the rtrv-rtx command.

    This is an example of the possible output.

    rlghncxa03w 08-02-11 11:43:04 GMT  EAGLE5 38.0.0
    
       DPCA          RTX-CRITERIA              LSN        RC    APC
    
       003-003-003   OPCA
                     009-009-009               lsn1       3     002-002-002
                     010-010-010               lsn1       2     002-002-002
                     ILSN
                     lsn3                      lsn2       2     002-002-003
                     lsn4                      lsn2       1     002-002-003
                     CIC - ECIC
                     15    15                  lsn2       1     002-002-003
                     17    17                  lsn2       7     002-002-003
                     18    30                  lsn1       8     002-002-002
                     SI
                     3                         lsn2       5     002-002-003
                     5                         lsn2       5     002-002-003
    
       DPCI          RTX-CRITERIA              LSN        RC    APC
    
       0-123-7       OPCI
                     1-222-3                   lsn3       10    1-234-5
                     1-222-4                   lsn3       11    1-234-5
                     1-222-5                   lsn4       11    2-145-6
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              12
        TOTAL DPC(s):                  32
        CAPACITY (% FULL):              2%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    If the rtrv-rtx output contains any entries, the Origin-Based MTP Routing feature is enabled. Continue the procedure with 3.

    If error message E4584 is displayed after the rtrv-rtx command is executed, the Origin-Based MTP Routing feature is not turned on.

    E4584 Cmd Rej: MTP Origin Based Routing Feature must be ON
    

    If error message E4584 is displayed, perform the Activating the Origin-Based MTP Routing Feature procedure to enable, if required, and turn on the Origin-Based MTP Routing feature. After the Origin-Based MTP Routing feature is turned on, continue the procedure with 2.

  2. Display the number of DPCs currently in the database and the number of DPCs that EAGLE can contain by entering the rtrv-dstn command with the msar=only parameter.

    This is an example of the possible output.

    rlghncxa03w 08-02-11 11:43:04 GMT  EAGLE5 38.0.0
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              12
        TOTAL DPC(s):                  32
        CAPACITY (% FULL):              2%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    
  3. The number of entries in the EAGLE routing table consists of the number of DPCs provisioned by the ent-dstn command and the number of exception routes provisioned by ent-rtx command.

    The number of entries in the EAGLE’s routing table cannot exceed the number of DPCs allocated in the routing table, shown in the DESTINATION ENTRIES ALLOCATED: row of the rtrv-rtx and rtrv-dstn output. The EAGLE can contain a maximum of 10,000 entries in the routing table. The total number of entries provisioned in the routing table is shown in the TOTAL DPC(s): row of the rtrv-dstn or rtrv-rtx output. If adding the new exception route entry would exceed the number of DPCs allocated in the routing table, perform one of these actions:

    After either these actions are performed, continue the procedure with 4.

    Note:

    If adding the new exception route entry would exceed the number of DPCs allocated in the routing table and neither of these actions are performed, this procedure cannot be performed. If the number of DPCs provisioned in the routing table is10,000, the only action that can be performed that would allow the addition of new exception routes is to remove existing entries from the routing table.

    If adding the new exception route entry would not exceed the number of DPCs allocated in the routing table, continue the procedure with 4.

  4. Display the routes in the database by entering the rtrv-rte command.

    If the new exception route entry will be added to an existing DPC shown in the rtrv-rtx output, continue the procedure with 5.

    This is an example of the possible output.

    rlghncxa03w 10-12-10 11:43:04 GMT EAGLE5 43.0.0
    Extended Processing Time may be Required
    
       DPCA           ALIASI     ALIASN/N24    LSN        RC    APCA
       002-002-002 ---------- --------------   ---------- --    -----------
                                                   RTX:No  CLLI=-----------
       002-002-003 ---------- --------------   ---------- --    -----------
                                                   RTX:No  CLLI=-----------
       003-003-003 ---------- --------------   lsn1       1     002-002-002
                                               lsn2       2     002-002-003
                                                   RTX:Yes CLLI=-----------
       004-004-004 ---------- --------------   ---------- --    -----------
                                                   RTX:No  CLLI=-----------
       005-005-005 ---------- --------------   ---------- --    -----------
                                                   RTX:No  CLLI=-----------
       006-006-006 ---------- --------------   lsn11      1     004-004-004
                                               lsn12      2     005-005-006
                                                   RTX:No  CLLI=-----------
       DPCI       ALIASN/N24       ALIASA      LSN        RC    APC
       0-123-7 --------------   -------------- lsn3       1     1-234-5
                                               lsn4       2     2-145-6
                                                   RTX:Yes CLLI=-----------
       1-234-5 --------------   -------------- ---------- --    -----------
                                                   RTX:No  CLLI=-----------
       2-145-6 --------------   -------------- ---------- --    -----------
                                                   RTX:No  CLLI=-----------
       3-025-6 --------------   -------------- lsn13      1     1-100-5
                                               lsn14      2     4-139-4
                                                   RTX:No  CLLI=-----------
       1-100-5 --------------   -------------- ---------- --    -----------
                                                   RTX:No  CLLI=-----------
       4-139-4 --------------   -------------- ---------- --    -----------
                                                   RTX:No  CLLI=-----------
       DPCN             ALIASA         ALIASI  LSN        RC    APC
       00002         -------------- ---------- ---------- --    -----------
                                                   RTX:No  CLLI=-----------
       00003         -------------- ---------- ---------- --    -----------
                                                   RTX:Yes CLLI=-----------
       00004         -------------- ---------- lsn5       1     00002
                                               lsn6       2     00003
                                                   RTX:No  CLLI=-----------
       11302         -------------- ---------- ---------- --    -----------
                                                   RTX:No  CLLI=-----------
       12567         -------------- ---------- ---------- --    -----------
                                                   RTX:No  CLLI=-----------
       09852         -------------- ---------- lsn15      1     11302
                                               lsn16      2     12567
                                                   RTX:No  CLLI=-----------
       DPCN24           ALIASA         ALIASI  LSN        RC    APC
    
    The DPC value assigned to the exception route must be assigned to a route. If the required route is not shown in the rtrv-rte output, perform one of these procedures to add the required route.

    After the required routes have been configured, continue the procedure with 5.

  5. Display the linksets in the database by entering the rtrv-ls command.

    This is an example of the possible output.

    rlghncxa03w 06-10-10 11:43:04 GMT EAGLE5 38.0.0
    
                                     L3T SLT              GWS GWS GWS
    LSN           APCA   (SS7)  SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
    lsn1          002-002-002   none 1   1   no  B   2    off off off no    off
    lsn2          002-002-003   none 1   1   no  B   3    off off off no    off
    lsn11         004-004-004   none 1   1   no  B   1    off off off no    off
    lsn12         005-005-005   none 1   1   no  B   4    off off off no    off
    
                                     L3T SLT              GWS GWS GWS
    LSN           APCI   (SS7)  SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
    lsn3          1-234-5       none 1   2   no  B   2    off off off ---   off
    lsn4          2-145-6       none 1   2   no  B   2    off off off ---   off
    lsn13         1-100-5       none 1   2   no  B   1    off off off ---   off
    lsn14         4-139-4       none 1   2   no  B   1    off off off ---   off
    
                                     L3T SLT              GWS GWS GWS
    LSN           APCN   (SS7)  SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
    lsn5          00002         none 1   2   no  B   2    off off off ---   off
    lsn6          00003         none 1   2   no  B   2    off off off ---   off
    lsn15         11302         none 1   2   no  B   2    off off off ---   off
    lsn16         12567         none 1   2   no  B   2    off off off ---   off
    
    Link set table is (12 of 1024) 1% full.
    

    If the required linkset is not in the database, perform one of these procedures to add the linkset.

    • Adding an SS7 Linkset
    • “Configuring an IPGWx Linkset,” "Adding an IPSG M2PA Linkset," or "Adding an IPSG M3UA Linkset" procedures in Database Administration - IP7 User's Guide.

    The linkset must be added according to the rules shown in the "Adding Linksets for Exception Routes" section.

    Note:

    If the DPC exception route entry is an ANSI DPC, the adjacent point code of thelsn value must be an ANSI point code. If the DPC exception route entry is an ANSI DPC, continue the procedure with7.
  6. Display the linkset that will be assigned to the exception route entry by entering the rtrv-ls command with the name of the linkset.

    For this example, enter these commands.

    rtrv-ls:lsn=lsn13

    This is an example of the possible output.

    rlghncxa03w 08-02-11 11:43:04 GMT  EAGLE5 38.0.0
    
                                     L3T SLT              GWS GWS GWS
    LSN           APCI   (SS7)  SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
    lsn13         1-100-5       none 1   2   no  B   1    off off off ---   off
    
               CLLI         TFATCABMLQ MTPRSE ASL8 SLSOCBIT SLSRSB MULTGC
               -----------  1          no     ---  none     7      no
    
               ITUTFR RANDSLS
               off    all
    
               IPGWAPC MATELSN    IPTPS LSUSEALM SLKUSEALM GTTMODE
               no      ---------- ---   ---      ---       CdPA
    
              LOC   LINK SLC TYPE     IPLIML2
              1301  A    0   IPLIMI   M2PA
              
              SAPCN
              11211
    Link set table is (12 of 1024) 1% full.
    

    rtrv-ls:lsn=lsn16

    This is an example of the possible output.

    rlghncxa03w 08-02-11 11:43:04 GMT  EAGLE5 38.0.0
    
                                     L3T SLT              GWS GWS GWS
    LSN           APCI   (SS7)  SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS
    lsn16         12567         none 1   2   no  B   2    off off off ---   off
    
               CLLI         TFATCABMLQ MTPRSE ASL8 SLSOCBIT SLSRSB MULTGC
               -----------  1          no     ---  none     7      no
    
               ITUTFR RANDSLS
               off    all
    
               IPGWAPC MATELSN    IPTPS LSUSEALM SLKUSEALM GTTMODE
               no      ---------- ---   ---      ---       CdPA
     
              LOC   LINK SLC TYPE     IPLIML2
              1301  A    0   IPLIMI   M2PA
    
              SAPCI
              5-067-1
    Link set table is (12 of 1024) 1% full.
    

    If the linkset does not meet the criteria shown in the "Adding Linksets for Exception Routes" section, either choose another linkset from the rtrv-ls output in 5 and repeat this step, or add a new linkset by performing one of these procedures:

    • Adding an SS7 Linkset
    • “Configuring an IPGWx Linkset,” "Adding an IPSG M2PA Linkset," or "Adding an IPSG M3UA Linkset" procedures in Database Administration - IP7 User's Guide.
    The linkset must be added according to the rules shown in the "Adding Linksets for Exception Routes" section. After this step is performed, continue the procedure by performing one of these steps.
    • If no more than two entries in the exception route will contain the same exception route criteria, except for the linkset name, continue the procedure with 14.
    • If more than two entries in the exception route will contain the same exception route criteria, except for the linkset name, continue the procedure by performing one of these steps.
      • If more than two entries in an exception route that contain the same exception route criteria, except for the linkset name, are shown in the rtrv-rtx command in 1, continue the procedure with 14.
      • If more than two entries in an exception route that contain the same exception route criteria, except for the linkset name, are not shown in the rtrv-rtx command in 1, continue the procedure with 13.
  7. Display the DPCs in the database by entering the rtrv-dstn command.

    Note:

    If cluster point codes are displayed in thertrv-rtx orrtrv-rte outputs, skip this step and continue the procedure with8.

    This is an example of the possible output.

    rlghncxa03w 10-12-10 11:43:04 GMT EAGLE5 43.0.0
    Extended Processing Time may be Required
    
       DPCA          CLLI        BEI ELEI   ALIASI          ALIASN/N24    DMN
       002-002-002   ----------- no  --- ----------      --------------   SS7
       002-002-003   ----------- no  --- ----------      --------------   SS7
       003-003-003   ----------- no  --- ----------      --------------   SS7
       004-004-004   ----------- no  --- ----------      --------------   SS7
       005-005-005   ----------- no  --- ----------      --------------   SS7
       006-006-006   ----------- no  --- ----------      --------------   SS7
    
       DPCI          CLLI        BEI ELEI   ALIASA          ALIASN/N24    DMN
       1-234-5       ----------- no  --- --------------  --------------   SS7
       2-145-6       ----------- no  --- --------------  --------------   SS7
       0-123-7       ----------- no  --- --------------  --------------   SS7
       3-025-6       ----------- no  --- --------------  --------------   SS7
       1-100-5       ----------- no  --- --------------  --------------   SS7
       4-139-4       ----------- no  --- --------------  --------------   SS7
       5-067-1       ----------- no  --- --------------  --------------   SS7
    
       DPCN          CLLI        BEI ELEI   ALIASA          ALIASI        DMN
       00002         ----------- no  --- --------------  ----------       SS7
       00003         ----------- no  --- --------------  ----------       SS7
       00004         ----------- no  --- --------------  ----------       SS7
       09852         ----------- no  --- --------------  ----------       SS7
       11211         ----------- no  --- --------------  ----------       SS7
       11302         ----------- no  --- --------------  ----------       SS7
       12567         ----------- no  --- --------------  ----------       SS7
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              12
        TOTAL DPC(s):                  32
        CAPACITY (% FULL):              2%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    If a cluster point code is not shown in the rtrv-dstn output, continue the procedure with 12.

    If a cluster point code is shown in the rtrv-dstn output, and the DPC of the exception route is not a member of a cluster point code, continue the procedure with 12.

    If a cluster point code is shown in the rtrv-dstn output, and the DPC of the exception route is a member of a cluster point code, continue the procedure with 8.

  8. Display the cluster point code by entering the rtrv-dstn command with the cluster point code.

    For this example, enter this command.

    rtrv-dstn:dpca=010-010-*

    This is an example of the possible output.

    rlghncxa03w 10-12-10 11:43:04 GMT EAGLE5 43.0.0
    
        DPCA          CLLI        BEI ELEI   ALIASI          ALIASN/N24    DMN
        010-010-*     ----------- no  no  ----------      --------------   SS7
    
       SPCA         NCAI         RCAUSE NPRST SPLITIAM HMSMSC HMSCP SCCPMSGCNV
       -----------  yes          none   off   none     no     no    none
    
     Destination table is (33 of 2000) 1% full
     Alias table is (0 of 12000) 0% full
    

    The DPC of an exception route cannot be a member of a cluster point code unless the NCAI value of the cluster point code is yes. If the NCAI value of the cluster point code is yes, continue the procedure with 12.

    If the NCAI value of the cluster point code is no, continue the procedure with 9.

  9. Verify that the NCR (Nested Cluster Routing) feature is on by entering the rtrv-feat command.

    The entry NCR = on in the rtrv-feat command output shows that the NCR feature is on.

    Note:

    The rtrv-feat command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by thertrv-feat command, see the rtrv-feat command description in Commands User's Guide.

    If the NCR feature is on, continue the procedure with 11.

    If the NCR feature is off, continue the procedure with 10.

  10. Turn the NCR feature on by entering this command.
    chg-feat:ncr=on

    Note:

    Once the NCR feature is turned on with the chg-feat command, it cannot be turned off.

    The NCR feature must be purchased before you turn the feature on with the chg-feat command. If you are not sure if you have purchased the NCR feature, contact your Sales Representative or Account Representative.

    When this command has successfully completed, this message should appear.

    rlghncxa03w 06-10-10 11:43:04 GMT EAGLE5 38.0.0
    CHG-FEAT: MASP A - COMPLTD
    
  11. Change the NCAI value for the cluster point code from no to yes by entering the chg-dstn command with the cluster point code and the ncai=yes parameter. For this example, enter this command.

    chg-dstn:dpca=010-010-*:ncai=yes.

    When this command has successfully completed, this message should appear.

    rlghncxa03w 08-02-11 15:35:05 GMT EAGLE5 38.0.0
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              12
        NETWORK DPC(s):                 0
        CLUSTER DPC(s):                 1
        TOTAL DPC(s):                  33
        CAPACITY (% FULL):             1%
    ALIASES ALLOCATED:              12000
        ALIASES USED:                   0
        CAPACITY (% FULL):             0%
    X-LIST ENTRIES ALLOCATED:         500
    CHG-DSTN: MASP A - COMPLTD
    

    Note:

    If theopc/opca parameter will not be specified with theent-rtx command, continue the procedure with12.
  12. The opc/opca value of the exception route can be specified with the network cluster and network cluster member values of the point code as asterisks (*).

    If the network cluster and network cluster member values of the opc/opca value will not be specified as asterisks, continue the procedure by performing one of the steps shown at the end of this step.

    If the network cluster and network cluster member values of the opc/opca value will be specified as asterisks, and the network indicator value of the opc/opca value is 6 or greater, continue the procedure by performing one of the steps shown at the end of this step.

    If the network cluster and network cluster member values of the opc/opca value will be specified as asterisks, and the network indicator value of the opc/opca value will be 1 through 5, the PCTYPE value shown in the rtrv-sid output must be OTHER. Enter the rtrv-sid command to verify the PCTYPE value.

    This is an example of the possible output.

    rlghncxa03w 06-10-10 11:43:04 GMT EAGLE5 38.0.0
    
       PCA             PCI          PCN                CLLI              PCTYPE
       001-001-001     1-001-1      00001              rlghncxa03w       OTHER
    
       CPCA
       002-002-004      002-002-005        002-002-006      002-002-007
       002-002-008      002-002-009        004-002-001      004-003-003
       050-060-070
    
       CPCI
       1-001-2           1-001-3           1-001-4          1-002-1
       1-002-2           1-002-3           1-002-4          2-001-1
       7-222-7
    
       CPCN
       00050             00060             00070            00100
       00080             00090
    

    If the PCTYPE value shown in the rtrv-sid output is OTHER, continue the procedure by performing one of the steps shown at the end of this step.

    If the PCTYPE value shown in the rtrv-sid output is ANSI, Change the PCTYPE value of the self-identification of the EAGLE to OTHER by performing the Changing the Self-Identification of the EAGLE procedure. After the PCTYPE value is changed, continue the procedure by performing one of the steps shown at the end of this step.

    Continue the procedure by performing one of these steps.
    • If no more than two entries in the exception route will contain the same exception route criteria, except for the linkset name, continue the procedure with 14.
    • If more than two entries in the exception route will contain the same exception route criteria, except for the linkset name, continue the procedure by performing one of these steps.
      • If more than two entries in an exception route that contain the same exception route criteria, except for the linkset name, are shown in the rtrv-rtx command in 1, continue the procedure with 14.
      • If more than two entries in an exception route that contain the same exception route criteria, except for the linkset name, are not shown in the rtrv-rtx command in 1, continue the procedure with 13.
  13. For an exception route to have more than two entries with the same exception route criteria, except for the linkset name (the lsn parameter value), the 6-Way Loadsharing on Routesets feature must be enabled and turned on.

    To verify the status of the 6-Way Loadsharing on Routesets feature, enter this command.

    rtrv-ctrl-feat:partnum=893019801

    The following is an example of the possible output.

    rlghncxa03w 09-05-28 21:15:37 GMT EAGLE5 41.0.0
    The following features have been permanently enabled:
    
    Feature Name              Partnum    Status  Quantity
    6-Way LS on Routesets     893019801  on      ----
    
    The following features have been temporarily enabled:
    
    Feature Name              Partnum   Status  Quantity     Trial Period Left
    Zero entries found.
    
    The following features have expired temporary keys:
    
    Feature Name              Partnum
    Zero entries found.
    

    If the 6-Way Loadsharing on Routesets feature is not enabled or not turned on, perform the Activating the 6-Way Loadsharing on Routesets Feature procedure to enable and turn on the 6-Way Loadsharing on Routesets feature.

    After the 6-Way Loadsharing on Routesets feature has been enabled and turned on, or if the rtrv-ctrl-feat output shows that the 6-Way Loadsharing on Routesets feature is enabled and turned on, continue this procedure with 14.

  14. Add the exception route entry by entering the ent-rtx command and specifying the parameter combinations shown in Table 3-27 for the exception route criteria being assigned to the exception route.

    Table 3-27 Add Exception Route Parameter Combinations

    OPC- Based Exception Lists ILSN- Based Exception Lists SI- Based Exception Lists Single CIC- Based Exception Lists Range of CICs- Based Exception Lists

    :dpc/dpca/

    dpci/dpcn/

    dpcn24 = DPC of the exception route shown in the rtrv-rtx or rtrv-rte outputs (See Notes 1, 2, 3, and 5)

    :dpc/dpca/

    dpci/dpcn/

    dpcn24 = DPC of the exception route shown in the rtrv-rtx or rtrv-rte outputs (See Notes 1, 2, and 3)

    :dpc/dpca/

    dpci/dpcn/

    dpcn24 = DPC of the exception route shown in the rtrv-rtx or rtrv-rte outputs (See Notes 1, 2, and 3)

    :dpc/dpca/

    dpci/dpcn/

    dpcn24 = DPC of the exception route shown in the rtrv-rtx or rtrv-rte outputs (See Notes 1, 2, and 3)

    :dpc/dpca/

    dpci/dpcn/

    dpcn24 = DPC of the exception route shown in the rtrv-rtx or rtrv-rte outputs (See Notes 1, 2, and 3)

    :opc/opca/

    opci/opcn/

    opcn24 = OPC value of the exception route (See Notes 5, 6, and 9)

    :ilsn = incoming linkset name shown in the rtrv-ls output (See Notes 4 and 6)

    :si = service indicator, 3 - 15

    :cic = circuit identification code, 0 - 16383 (See Note 8)

    :cic = the circuit identification code value beginning a range of CICs, 0 - 16383 (See Note 8)

    :lsn = linkset name shown in the rtrv-ls output (See Notes 4 and 6)

    :lsn = linkset name shown in the rtrv-ls output (See Notes 5, 6, and 9)

    :lsn = linkset name shown in the rtrv-ls output (See Note 4)

    :lsn = linkset name shown in the rtrv-ls output (See Note 4)

    :ecic = the circuit identification code value ending a range of CICs, 0 - 16383 (See Notes 7 and 8)

    :rc = 0 - 99

    :rc = 0 - 99

    :rc = 0 - 99

    :rc = 0 - 99

    :lsn = linkset name shown in the rtrv-ls output (See Note 4)

    :force=yes (See Note 6)

    :force=yes (See Note 6)

       

    :rc = 0 - 99

    Notes:

    1. The DPC of an exception route entry can contain only a maximum of two entries with the same RC value and with either the same OPC value, the same ILSN value, the same SI value, the same CIC value, or range of CIC values if the 6-Way Loadsharing on Routesets feature is not enabled or turned on. If the 6-Way Loadsharing on Routesets feature is enabled and turned on, the DPC of an exception route entry can contain more than two entries with the same RC value and with either the same OPC value, the same ILSN value, the same SI value, the same CIC value, or range of CIC values, the LSN value for each entry must be different.

    2. Each DPC can contain a maximum of six entries with either the same OPC value, the same ILSN value, the same SI value, or the same range of CIC values. The LSN value for each entry must be different. If the 6-Way Loadsharing on Routesets feature is not enabled or turned on, the DPC of a route exception entry can contain only one entry with a single CIC value. If the 6-Way Loadsharing on Routesets feature is enabled and turned on, the DPC of a route exception entry can contain more than one entry with a single CIC value.

    4. The linksets specified in this step must meet the criteria shown in the "Adding Linksets for Exception Routes" section.

    5. The DPC value cannot be the same as the OPC value.

    6. The force=yes parameter must be used if the LSN and ILSN values are the same, or if the OPC value is the same as the APC of the linkset specified by the lsn parameter.

    7. The ecic parameter value must be greater than the cic parameter value.

    8. The range of CIC values cannot overlap an existing range of CIC values. A single CIC value cannot be within a range of CIC values provisioned for another exception route entry. The cic or ecic values cannot be the same as any single CIC values provisioned for another exception route entry.

    9. Asterisks can be used as the values for the network cluster and network cluster member portions of an ANSI point code value for the opc/opca parameter. For example, the opc/opca value could be 004-004-* or 007-*-*. An opc/opca value containing all asterisks (*-*-*) is not allowed.

    For this example, enter these commands.

    ent-rtx:dpca=006-006-006:opca=125-150-175:lsn=lsn11:rc=10

    ent-rtx:dpca=006-006-006:opci=2-103-1:lsn=lsn11:rc=20

    ent-rtx:dpca=006-006-006:ilsn=lsn12:lsn=lsn11:rc=11

    ent-rtx:dpca=006-006-006:ilsn=lsn13:lsn=lsn11:rc=12

    ent-rtx:dpca=006-006-006:si=5:lsn=lsn12:rc=10

    ent-rtx:dpca=006-006-006:cic=250:lsn=lsn12:rc=15

    ent-rtx:dpca=006-006-006:cic=300:ecic=500:lsn=lsn12:rc=25

    ent-rtx:dpci=3-025-6:opca=135-102-089:lsn=lsn13:rc=10

    ent-rtx:dpci=3-025-6:opci=4-054-0:lsn=lsn13:rc=15

    ent-rtx:dpci=3-025-6:opcn=00503:lsn=lsn13:rc=45

    ent-rtx:dpci=3-025-6:ilsn=lsn2:lsn=lsn14:rc=20

    ent-rtx:dpci=3-025-6:ilsn=lsn4:lsn=lsn13:rc=25

    ent-rtx:dpci=3-025-6:ilsn=lsn16:lsn=lsn16:rc=50:force=yes

    ent-rtx:dpci=3-025-6:si=3:lsn=lsn13:rc=30

    ent-rtx:dpci=3-025-6:cic=100:lsn=lsn14:rc=35

    ent-rtx:dpci=3-025-6:cic=50:ecic=75:lsn=lsn13:rc=40

    ent-rtx:dpcn=09852:opca=127-063-048:lsn=lsn15:rc=10

    ent-rtx:dpcn=09852:opci=3-037-1:lsn=lsn16:rc=15

    ent-rtx:dpcn=09852:opcn=00409:lsn=lsn13:rc=20

    ent-rtx:dpcn=09852:ilsn=lsn13:lsn=lsn15:rc=25

    ent-rtx:dpcn=09852:ilsn=lsn4:lsn=lsn16:rc=30

    ent-rtx:dpcn=09852:si=4:lsn=lsn15:rc=35

    ent-rtx:dpcn=09852:cic=1000:lsn=lsn16:rc=40

    ent-rtx:dpcn=09852:cic=2000:ecic=3000:lsn=lsn15:rc=45

    When each of these commands have successfully completed, this message should appear.

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    ENT-RTX: MASP A - COMPLTD
    
  15. Verify the changes using the rtrv-rtx command, specifying these parameters depending on the exception route criteria specified in 14.
    • If the opc/opca/opci/opcn/opcn24 parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, opc/opca/opci/opcn/opcn24, and lsn.
    • If the ilsn parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, ilsn, and lsn.
    • If the si parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, si, and lsn.
    • If only the cic parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, cic, and lsn.
    • If the cic and ecic parameters were specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, cic, ecic, and lsn.

    For this example, enter these commands.

    rtrv-rtx:dpca=006-006-006:opca=125-150-175:lsn=lsn11

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCA          RTX-CRITERIA              LSN        RC    APC
    
       006-006-006   OPCA
                     125-150-175               lsn11      10    004-004-004
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpca=006-006-006:opci=2-103-1:lsn=lsn11

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCA          RTX-CRITERIA              LSN        RC    APC
    
       006-006-006   OPCI
                     2-103-1                   lsn11      20    004-004-004
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpca=006-006-006:ilsn=lsn12:lsn=lsn11

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCA          RTX-CRITERIA              LSN        RC    APC
    
       006-006-006   ILSN
                     lsn12                     lsn11      11    004-004-004
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpca=006-006-006:ilsn=lsn13:lsn=lsn11

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCA          RTX-CRITERIA              LSN        RC    APC
    
       006-006-006   ILSN
                     lsn13                     lsn11      12    004-004-004
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpca=006-006-006:si=5:lsn=lsn12

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCA          RTX-CRITERIA              LSN        RC    APC
    
       006-006-006   SI
                     5                         lsn12      10    005-005-005
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpca=006-006-006:cic=250:lsn=lsn12

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCA          RTX-CRITERIA              LSN        RC    APC
    
       006-006-006   CIC - ECIC
                     250   250                 lsn12      15    005-005-005
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpca=006-006-006:cic=300:ecic=500:lsn=lsn12

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCA          RTX-CRITERIA              LSN        RC    APC
    
       006-006-006   CIC - ECIC
                     250   250                 lsn12      15    005-005-005
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpci=3-025-6:opca=135-102-089:lsn=lsn13

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCI          RTX-CRITERIA              LSN        RC    APC
    
       3-025-6       OPCA
                     135-102-089               lsn13      10    1-100-5
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpci=3-025-6:opci=4-054-0:lsn=lsn13

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCI          RTX-CRITERIA              LSN        RC    APC
    
       3-025-6       OPCI
                     4-054-0                   lsn13      15    1-100-5
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpci=3-025-6:opcn=00503:lsn=lsn13

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCI          RTX-CRITERIA              LSN        RC    APC
    
       3-025-6       OPCN
                     00503                     lsn11      15    1-100-5
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpci=3-025-6:ilsn=lsn2:lsn=lsn14

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCI          RTX-CRITERIA              LSN        RC    APC
    
       3-025-6       ILSN
                     lsn2                      lsn14      45    4-139-4
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpci=3-025-6:ilsn=lsn4:lsn=lsn13

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCI          RTX-CRITERIA              LSN        RC    APC
    
       3-025-6       ILSN
                     lsn4                      lsn13      25    1-100-5
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpci=3-025-6:ilsn=lsn16:lsn=lsn16

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCI          RTX-CRITERIA              LSN        RC    APC
    
       3-025-6       ILSN
                     lsn16                     lsn16      50    12567
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpci=3-025-6:si=3:lsn=lsn13

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCI          RTX-CRITERIA              LSN        RC    APC
    
       3-025-6       SI
                     3                         lsn13      30    1-100-5
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpci=3-025-6:cic=100:lsn=lsn14

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCI          RTX-CRITERIA              LSN        RC    APC
    
       3-025-6       CIC - ECIC
                     100   100                 lsn14      35    4-139-4
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpci=3-025-6:cic=50:ecic=75:lsn=lsn13

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCI          RTX-CRITERIA              LSN        RC    APC
    
       3-025-6       CIC - ECIC
                     50    75                  lsn13      40    1-100-5
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpcn=09852:opca=127-063-048:lsn=lsn15

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCN          RTX-CRITERIA              LSN        RC    APC
    
       09852         OPCA
                     127-063-048               lsn15      10    11302
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpcn=09852:opci=3-037-1:lsn=lsn16

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCN          RTX-CRITERIA              LSN        RC    APC
    
       09852         OPCI
                     3-037-1                   lsn16      15    12567
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpcn=09852:opcn=00409:lsn=lsn13

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCN          RTX-CRITERIA              LSN        RC    APC
    
       09852         OPCN
                     00409                     lsn13      20    1-100-5
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpcn=09852:ilsn=lsn13:lsn=lsn15

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCN          RTX-CRITERIA              LSN        RC    APC
    
       09852         ILSN
                     lsn13                     lsn15      25    11302
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpcn=09852:ilsn=lsn4:lsn=lsn16

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCN          RTX-CRITERIA              LSN        RC    APC
    
       09852         ILSN
                     lsn4                      lsn16      30    12567
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpcn=09852:si=4:lsn=lsn15

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCN          RTX-CRITERIA              LSN        RC    APC
    
       09852         SI
                     4                         lsn15      35    11302
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpcn=09852:cic=1000:lsn=lsn16

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCN          RTX-CRITERIA              LSN        RC    APC
    
       09852         CIC - ECIC
                     1000                      lsn16      40    12567
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    

    rtrv-rtx:dpcn=09852:cic=2000:ecic=3000:lsn=lsn15

    rlghncxa03w 08-02-11 08:28:30 GMT  EAGLE5 38.0.0
    
       DPCN          RTX-CRITERIA              LSN        RC    APC
    
       09852         CIC - ECIC
                     2000  3000                lsn15      45    11302
    
    DESTINATION ENTRIES ALLOCATED:   2000
        FULL DPC(s):                   20
        EXCEPTION DPC(s):              36
        TOTAL DPC(s):                  56
        CAPACITY (% FULL):              3%
    ALIASES ALLOCATED:               12000
        ALIASES USED:                   0
        CAPACITY (% FULL):              0%
    
  16. Back up the new changes using the chg-db:action=backup:dest=fixed command.

    These messages should appear, the active Maintenance and Administration Subsystem Processor (MASP) appears first.

    BACKUP (FIXED) : MASP A - Backup starts on active MASP.
    BACKUP (FIXED) : MASP A - Backup on active MASP to fixed disk complete.
    BACKUP (FIXED) : MASP A - Backup starts on standby MASP.
    BACKUP (FIXED) : MASP A - Backup on standby MASP to fixed disk complete.
    

Figure 3-42 Adding an Exception Route Entry



Sheet 1 of 10



Sheet 2 of 10





Sheet 3 of 10





Sheet 4 of 10





Sheet 5 of 10



Sheet 6 of 10



Sheet 7 of 10



Sheet 8 of 10





Sheet 9 of 10





Sheet 10 of 10