Adding an Allowed Affected Destination Field Screen

This procedure is used to add an allowed affected destination field (DESTFLD) screen to the database using the ent-scr-destfld command. The parameters used by the ent-scr-destfld command are shown in the Gateway Screening Attributes section. The general rules that apply to configuring gateway screening entities are shown in the Gateway Screening Configuration section.

The examples in this procedure are used to add the allowed DESTFLD screen data shown in Table 7-1 and based on the example configuration shown in Figure 2-7.

Table 7-1 Example Gateway Screening Allowed DESTFLD Configuration Table

Screening Reference	NI	NC	NCM	NSFI	ACTNAME
fld5	100	100	100	stop	CR

Note:

If you using multiple-part ITU national point codes with gateway screening, see the 14-Bit ITU National Point Code Formats section.

Specifying a Range of Values

A range of values can be specified for the point code parameters ni, nc, or ncm.

If a range of values is specified for any of these parameters, and the value of the other parameters match existing values for the screening reference name, the range of values for the point code parameter cannot include any values for that parameter that are currently provisioned for the screening reference name.

For example, screening reference name scr1 contains these entries:

SR    NI       NC       NCM      NSFI    NSR/ACT
SCR1  240      001      010      STOP    ------
SCR1  241      010      020      STOP    ------

Another entry for screening reference scr1 with the ni value of 240 and the nc value of 001 cannot be specified if the range of values for the ncm parameter includes the value 010.

The ANSI point code parameter values can be specified as a single value, a range of values, or with an asterisk (*). The asterisk specifies all possible values for the ni, nc, and ncm parameters. Table 7-2 shows the valid combinations of these parameter values.

Table 7-2 Valid Value Combinations for ANSI Point Code Parameters

NI	NC	NCM
Single Value	Single Value	Single Value
Single Value	Single Value	Range of Values
Single Value	Single Value	Asterisk
Single Value	Range of Values	Asterisk
Single Value	Asterisk	Asterisk
Range of Values	Asterisk	Asterisk
Asterisk	Asterisk	Asterisk

A range of values can also be specified for an ITU-I or 24-bit ITU-N point code parameter using a combination of asterisks (*) and single values for the point code parameters. Table 7-3 shows the valid combinations of the ITU-I parameter values. Table 7-4 shows the valid combinations of the 24-bit ITU-N parameter values.

Table 7-3 Valid Value Combinations for ITU-I Point Code Parameters

ZONE	AREA	ID
Single Value	Single Value	Single Value
Single Value	Single Value	Asterisk
Single Value	Asterisk	Asterisk
Asterisk	Asterisk	Asterisk

Table 7-4 Valid Value Combinations for 24-Bit ITU-N Point Code Parameters

MSA	SSA	SP
Single Value	Single Value	Single Value
Single Value	Single Value	Asterisk
Single Value	Asterisk	Asterisk
Asterisk	Asterisk	Asterisk

Verify that the gateway screening feature is on, by entering the rtrv-feat command.

If the gateway screening feature is on, the GWS field is set to on.

Note:
Thertrv-feat command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by thertrv-feat command, see thertrv-feat command description inCommands User's Guide.

If the gateway screening feature is on, shown by the entry GWS = on in the rtrv-feat command output, skip step 2, and go to step 3.
Turn the gateway screening feature on by entering this command.
chg-feat:gws=on

Note:
Once the gateway screening feature is turned on with thechg-feat command, it cannot be turned off.
The gateway screening feature must be purchased before you turn this feature on with the chg-feat command. If you are not sure if you have purchased the gateway screening feature, contact your Oracle Sales Representative or Account Representative.

When the chg-feat has successfully completed, this message should appear.
```
rlghncxa03w 06-10-28 11:43:04 GMT EAGLE5 36.0.0
CHG-FEAT: MASP A - COMPLTD
```
Display all allowed DESTFLD screens in the database using the rtrv-scr-destfld command.
The following is an example of the possible output.
```
rlghncxa03w 06-10-25 15:25:30 GMT EAGLE5 36.0.0
SCREEN = ALLOWED DESTFLD
SR    REF  RULES
IEC   YES     2
WRD2  YES     1
WRD4  YES     9
```
If the screening reference names that you wish to add with this procedure are not shown in the rtrv-scr-destfld command output, go to step 4. For this example, the screening reference names are not shown. If these screening reference names are shown in the rtrv-scr-destfld command output, make sure the screening data you wish to enter is not already in the database by entering the rtrv-scr-destfld command with the screening reference name. For example, enter the rtrv-scr-destfld:sr=iec command.

The following is an example of the possible output.
```
rlghncxa03w 06-10-25 15:26:30 GMT  EAGLE5 36.0.0
SCREEN = ALLOWED DESTFLD
SR    NI       NC       NCM      NSFI   NSR/ACT
IEC   240      001      010      STOP    ------
IEC   241      010      *        STOP    COPY
```
If a gateway screening stop action set is to be assigned to the allowed DESTFLD screen being added to the database, go to step 4. Otherwise, go to step 5.
Display the gateway screening stop action sets in the database with the rtrv-gws-actset command.
This is an example of the possible output.
```
rlghncxa03w 06-10-25 15:28:30 GMT EAGLE5 36.0.0
ACT  ACT    ACT  ACT  ACT  ACT  ACT  ACT  ACT  ACT  ACT  ACT
ID   NAME   1    2    3    4    5    6    7    8    9    10
--   ------ ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
1    copy   copy      
2    rdct   rdct      
3    cr     copy rdct 
4    cncf   cncf      
5    cpcncf copy cncf 
6    cncfrd cncf rdct 
7    cpcfrd copy cncf rdct

GWS action set table is (7 of 16) 44% full
```
If the required gateway screening stop action set is not in the database, perform the Configuring Gateway Screening Stop Action Sets procedure to configure the required gateway screening stop action set.

Note:
If the point code being added in this procedure is not an ITU-I or 14-bit ITU-N spare point code, skip this step and to step 6.

Note:
If the point code being added in this procedure is an ITU-I or 14-bit ITU-N spare point code and the screening reference contains ITU-I or 14-bit ITU-N spare point codes, skip this step and go to step 6.
Display the status of the ITU National and International Spare Point Code Support feature by entering the rtrv-ctrl-feat command with the ITU National and International Spare Point Code Support feature part number.
Enter this command.

rtrv-ctrl-feat:partnum=893013601

This is an example of the possible output.
```
rlghncxa03w 06-10-25 15:25:30 GMT EAGLE5 36.0.0
The following features have been permanently enabled:

Feature Name              Partnum   Status Quantity
Spare Point Code Support  893013601 on     ----

The following features have been temporarily enabled:

Feature Name              Partnum   Status Quantity   Trial Period Left
Zero entries found.

The following features have expired temporary keys:

Feature Name              Partnum
Zero entries found.
```
If the ITU National and International Spare Point Code Support feature is enabled, go to step 6.

If the ITU National and International Spare Point Code Support feature is not enabled, perform the “Activating the ITU National and International Spare Point Code Support Feature” procedure in Database Administration - SS7 User's Guide to enable the ITU National and International Spare Point Code Support feature as required. After the feature has been enabled, go to step 6.
Add a new allowed DESTFLD screen to the database using the ent-scr-destfld command.

If a gateway screening stop action is to be assigned to the allowed DESTFLD screen being changed, enter the ent-scr-destfld command with the nsfi=stop parameter and the actname parameter with the name of a gateway screening stop action set shown in the output of the rtrv-gws-actset command executed in step 4.

The following list contains the values for ni, nc, ncm, zone, area, id, npc, msa, ssa, and sp parameters:
- ni – 0 - 255 or an asterisk (*)
- nc – 0 - 255 or an asterisk (*)
- ncm – 0 - 255 or an asterisk (*)
- zone – 0 - 7 or an asterisk (*)
- area – 0 - 255 or an asterisk (*)
- id – 0 - 7 or an asterisk (*)
- npc – 1 - 16383 or an asterisk (*)
- msa – 0 - 255 or an asterisk (*)
- ssa – 0 - 255 or an asterisk (*)
- sp – 0 - 255 or an asterisk (*)
A range of values can be specified for the ni, nc, and ncm parameters. See the Specifying a Range of Values section for more information on how the asterisk and a range of values are used for the ni, nc, and ncm parameters.

To add a spare point code to the allowed DESTFLD screen, the pcst=s parameter must be specified. To add a non-spare point code to the allowed DESTFLD screen, the pcst parameter does not have to be specified. If the pcst parameter is specified for a screen containing an ITU-I or 14-bit ITU-N non-spare point code, the value must be none.

For this example, enter this command.

ent-scr-destfld:sr=fld5:ni=100:nc=100:ncm=100:nsfi=stop :actname=cr

A message similar to the following should appear.
```
rlghncxa03w 06-10-25 15:29:30 GMT  EAGLE5 36.0.0
ENT-SCR-DESTFLD: SCREEN SET AFFECTED - FLD5  1% FULL
ENT-SCR-DESTFLD: MASP A - COMPLTD
```
Verify the changes using the rtrv-scr-destfldcommand with the screening reference name used in step 6. For this example, enter this command.
rtrv-scr-destfld:sr=fld5

The following is an example of the possible output.
```
rlghncxa03w 06-10-25 15:30:30 GMT  EAGLE5 36.0.0
SCREEN = ALLOWED DESTFLD
SR    NI       NC       NCM      NSFI   NSR/ACT
FLD5  100      100      100      STOP    CR
```

Backup the new changes using the chg-db:action=backup:dest=fixed command.

The following messages should appear, the active Maintenance and Administration Subsystem Processor (MASP) appears first.

BACKUP (FIXED) : MASP A - Backup starts on active MASP.
BACKUP (FIXED) : MASP A - Backup on active MASP to fixed disk complete.
BACKUP (FIXED) : MASP A - Backup starts on standby MASP.
BACKUP (FIXED) : MASP A - Backup on standby MASP to fixed disk complete.

Figure 7-5 Add an Allowed Affected Destination Field Screen - Sheet 1 of 3

Figure 7-6 Add an Allowed Affected Destination Field Screen - Sheet 2 of 3

Figure 7-7 Add an Allowed Affected Destination Field Screen - Sheet 3 of 3