Oracle® Communications EAGLE Database Administration - SS7 User's Guide Release 46.7 E97335 Revision 1 |
|
![]() Previous |
![]() Next |
This procedure is used to add an exception route to the database using the ent-rtx
command. The ent-rtx
command uses these parameters.
:dpc
/dpca
/dpci
/dpcn
/dpcn24
– The destination point code of the node that the traffic is being sent to.
:opc
/opca
/opci
/opcn
/opcn24
– The originating point code of the node sending traffic to the EAGLE.
Note:
See Point Code Formats for a definition of the point code types that are used on the EAGLE and for a definition of the different formats that can be used for ITU national point codes.:ilsn
– The name of the linkset carrying incoming traffic to the EAGLE.
:lsn
– The name of the linkset that will carry the traffic to the node specified by the destination point code.
:si
– The service indicator value that will be assigned to the exception route. The value of the si
parameter is 3 to 15.
:cic
– The circuit identification code (CIC) value that will be assigned to an exception route containing a single CIC entry or the CIC value that begins a range of CICs that will be assigned to the exception route. The value of the cic
parameter is 0 to 16383.
:ecic
– The circuit identification code value that ends the range of CICs that will be assigned to the exception route. The value of the ecic
parameter is 0 to 16383.
:rc
– The relative cost value (priority) that will be assigned to the exception route. The value of the rc
parameter is 0 to 99.
:force
– This parameter allows an exception route to be added to the database even if the ilsn
parameter value is the same as the lsn
parameter value. This parameter has only one value, yes
.
The combinations of these parameters that can be used with the ent-rtx
command are shown in Table 3-27.
To add an exception route to the database, the Origin-Based MTP Routing feature must be enabled and turned on. If error message E4584 is displayed after the rtrv-rtx
command is executed, the Origin-Based MTP Routing feature is not enabled or turned on.
E4584 Cmd Rej: MTP Origin Based Routing Feature must be ON
If the Origin-Based MTP Routing feature is not enabled or turned on, perform the Activating the Origin-Based MTP Routing Feature procedure to enable, if required, and turn on the Origin-Based MTP Routing feature.
The DPC value assigned to the exception route must be assigned to a route. If the required route is not shown in the rtrv-rte
output, perform on of these procedures to add the required route.
The names of the linksets required specified for the lsn
and ilsn
parameters must be provisioned in the database. This can be verified by entering the rtrv-ls
command. If the required linkset is not in the database, perform one of these procedures to add the linkset.
The linkset must be added according to the rules shown in the "Adding Linksets for Exception Routes" section.
Adding Linksets for Exception Routes
The linkset must be added according to the following rules:
dpc
value of the exception route entry is an ANSI point code, the adjacent point code of the lsn
value must be an ANSI point code. opc
parameter value cannot be the adjacent point code of the linkset that is specified by the lsn
parameter value. dpc
value of the exception route entry is an ITU-I point code, the adjacent point code of the lsn
value must be an ITU-I point code. If the linkset contains an SAPC (secondary adjacent point code), the adjacent point code of the lsn
value can be either an ITU-N or ITU-N24 point code if the sapc
value is an ITU-I point code. If the adjacent point code of the lsn
value is an ITU-N point code with a group code, when the exception route is added, the group code of the adjacent point code of the linkset does not have to be the same as the group code of the opcn
value. If an ITU-N linkset is specified for the ilsn
parameter, the group code of the adjacent point code of the ilsn
value does not have to match the group code of the adjacent point code of the lsn
value. dpc
value of the exception route entry is an ITU-N point code, the adjacent point code of the lsn
value must be an ITU-N point code. dpc
value of the exception route entry is an ITU-N point code with no group code assigned to the ITU-N point code, the adjacent point code of the lsn
value or the adjacent point code of all the linksets in the routeset can be an ITU-I point code if the sapc
(secondary adjacent point code) value is an ITU-N point code. dpc
value of the exception route entry is an ITU-N point code with a group code, the adjacent point code of the lsn
value can be an ITU-I point code if the sapc
value is an ITU-N point code. When the exception route is added, the group code of the dpcn
value and the opcn
value must be the same. The group code of the adjacent point code of the lsn
value and the ilsn
value must be the same. The group code of the dpcn
value must be the same as the group code of either the adjacent point code of the lsn
value or the sapc
(secondary adjacent point code) assigned to the lsn
value. dpc
value of the exception route entry is an ITU-N24 point code, the adjacent point code of the lsn
value must be an ITU-N24 point code. If the linkset contains an SAPC (secondary adjacent point code), the adjacent point code of the lsn
value can be an ITU-I point code if the sapc
value is an ITU-N24 point code. The SAPC values assigned to the linksets can be verified by entering the rtrv-ls:lsn=<linkset name>
command.
rtrv-rtx
command. This is an example of the possible output.
rlghncxa03w 08-02-11 11:43:04 GMT EAGLE5 38.0.0 DPCA RTX-CRITERIA LSN RC APC 003-003-003 OPCA 009-009-009 lsn1 3 002-002-002 010-010-010 lsn1 2 002-002-002 ILSN lsn3 lsn2 2 002-002-003 lsn4 lsn2 1 002-002-003 CIC - ECIC 15 15 lsn2 1 002-002-003 17 17 lsn2 7 002-002-003 18 30 lsn1 8 002-002-002 SI 3 lsn2 5 002-002-003 5 lsn2 5 002-002-003 DPCI RTX-CRITERIA LSN RC APC 0-123-7 OPCI 1-222-3 lsn3 10 1-234-5 1-222-4 lsn3 11 1-234-5 1-222-5 lsn4 11 2-145-6 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 12 TOTAL DPC(s): 32 CAPACITY (% FULL): 2% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
If the rtrv-rtx
output contains any entries, the Origin-Based MTP Routing feature is enabled. Continue the procedure with 3.
If error message E4584 is displayed after the rtrv-rtx
command is executed, the Origin-Based MTP Routing feature is not turned on.
E4584 Cmd Rej: MTP Origin Based Routing Feature must be ON
If error message E4584 is displayed, perform the Activating the Origin-Based MTP Routing Feature procedure to enable, if required, and turn on the Origin-Based MTP Routing feature. After the Origin-Based MTP Routing feature is turned on, continue the procedure with 2.
rtrv-dstn
command with the msar=only
parameter. This is an example of the possible output.
rlghncxa03w 08-02-11 11:43:04 GMT EAGLE5 38.0.0 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 12 TOTAL DPC(s): 32 CAPACITY (% FULL): 2% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
ent-dstn
command and the number of exception routes provisioned by ent-rtx
command. The number of entries in the EAGLE’s routing table cannot exceed the number of DPCs allocated in the routing table, shown in the DESTINATION ENTRIES ALLOCATED:
row of the rtrv-rtx
and rtrv-dstn
output. The EAGLE can contain a maximum of 10,000 entries in the routing table. The total number of entries provisioned in the routing table is shown in the TOTAL DPC(s):
row of the rtrv-dstn
or rtrv-rtx
output. If adding the new exception route entry would exceed the number of DPCs allocated in the routing table, perform one of these actions:
After either these actions are performed, continue the procedure with 4.
Note:
If adding the new exception route entry would exceed the number of DPCs allocated in the routing table and neither of these actions are performed, this procedure cannot be performed. If the number of DPCs provisioned in the routing table is10,000, the only action that can be performed that would allow the addition of new exception routes is to remove existing entries from the routing table.If adding the new exception route entry would not exceed the number of DPCs allocated in the routing table, continue the procedure with 4.
rtrv-rte
command. If the new exception route entry will be added to an existing DPC shown in the rtrv-rtx
output, continue the procedure with 5.
This is an example of the possible output.
rlghncxa03w 10-12-10 11:43:04 GMT EAGLE5 43.0.0 Extended Processing Time may be Required DPCA ALIASI ALIASN/N24 LSN RC APCA 002-002-002 ---------- -------------- ---------- -- ----------- RTX:No CLLI=----------- 002-002-003 ---------- -------------- ---------- -- ----------- RTX:No CLLI=----------- 003-003-003 ---------- -------------- lsn1 1 002-002-002 lsn2 2 002-002-003 RTX:Yes CLLI=----------- 004-004-004 ---------- -------------- ---------- -- ----------- RTX:No CLLI=----------- 005-005-005 ---------- -------------- ---------- -- ----------- RTX:No CLLI=----------- 006-006-006 ---------- -------------- lsn11 1 004-004-004 lsn12 2 005-005-006 RTX:No CLLI=----------- DPCI ALIASN/N24 ALIASA LSN RC APC 0-123-7 -------------- -------------- lsn3 1 1-234-5 lsn4 2 2-145-6 RTX:Yes CLLI=----------- 1-234-5 -------------- -------------- ---------- -- ----------- RTX:No CLLI=----------- 2-145-6 -------------- -------------- ---------- -- ----------- RTX:No CLLI=----------- 3-025-6 -------------- -------------- lsn13 1 1-100-5 lsn14 2 4-139-4 RTX:No CLLI=----------- 1-100-5 -------------- -------------- ---------- -- ----------- RTX:No CLLI=----------- 4-139-4 -------------- -------------- ---------- -- ----------- RTX:No CLLI=----------- DPCN ALIASA ALIASI LSN RC APC 00002 -------------- ---------- ---------- -- ----------- RTX:No CLLI=----------- 00003 -------------- ---------- ---------- -- ----------- RTX:Yes CLLI=----------- 00004 -------------- ---------- lsn5 1 00002 lsn6 2 00003 RTX:No CLLI=----------- 11302 -------------- ---------- ---------- -- ----------- RTX:No CLLI=----------- 12567 -------------- ---------- ---------- -- ----------- RTX:No CLLI=----------- 09852 -------------- ---------- lsn15 1 11302 lsn16 2 12567 RTX:No CLLI=----------- DPCN24 ALIASA ALIASI LSN RC APC
rtrv-rte
output, perform one of these procedures to add the required route.
After the required routes have been configured, continue the procedure with 5.
rtrv-ls
command. This is an example of the possible output.
rlghncxa03w 06-10-10 11:43:04 GMT EAGLE5 38.0.0 L3T SLT GWS GWS GWS LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS lsn1 002-002-002 none 1 1 no B 2 off off off no off lsn2 002-002-003 none 1 1 no B 3 off off off no off lsn11 004-004-004 none 1 1 no B 1 off off off no off lsn12 005-005-005 none 1 1 no B 4 off off off no off L3T SLT GWS GWS GWS LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS lsn3 1-234-5 none 1 2 no B 2 off off off --- off lsn4 2-145-6 none 1 2 no B 2 off off off --- off lsn13 1-100-5 none 1 2 no B 1 off off off --- off lsn14 4-139-4 none 1 2 no B 1 off off off --- off L3T SLT GWS GWS GWS LSN APCN (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS lsn5 00002 none 1 2 no B 2 off off off --- off lsn6 00003 none 1 2 no B 2 off off off --- off lsn15 11302 none 1 2 no B 2 off off off --- off lsn16 12567 none 1 2 no B 2 off off off --- off Link set table is (12 of 1024) 1% full.
If the required linkset is not in the database, perform one of these procedures to add the linkset.
The linkset must be added according to the rules shown in the "Adding Linksets for Exception Routes" section.
Note:
If the DPC exception route entry is an ANSI DPC, the adjacent point code of thelsn
value must be an ANSI point code. If the DPC exception route entry is an ANSI DPC, continue the procedure with7. rtrv-ls
command with the name of the linkset. For this example, enter these commands.
rtrv-ls:lsn=lsn13
This is an example of the possible output.
rlghncxa03w 08-02-11 11:43:04 GMT EAGLE5 38.0.0 L3T SLT GWS GWS GWS LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS lsn13 1-100-5 none 1 2 no B 1 off off off --- off CLLI TFATCABMLQ MTPRSE ASL8 SLSOCBIT SLSRSB MULTGC ----------- 1 no --- none 7 no ITUTFR RANDSLS off all IPGWAPC MATELSN IPTPS LSUSEALM SLKUSEALM GTTMODE no ---------- --- --- --- CdPA LOC LINK SLC TYPE IPLIML2 1301 A 0 IPLIMI M2PA SAPCN 11211 Link set table is (12 of 1024) 1% full.
rtrv-ls:lsn=lsn16
This is an example of the possible output.
rlghncxa03w 08-02-11 11:43:04 GMT EAGLE5 38.0.0 L3T SLT GWS GWS GWS LSN APCI (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS lsn16 12567 none 1 2 no B 2 off off off --- off CLLI TFATCABMLQ MTPRSE ASL8 SLSOCBIT SLSRSB MULTGC ----------- 1 no --- none 7 no ITUTFR RANDSLS off all IPGWAPC MATELSN IPTPS LSUSEALM SLKUSEALM GTTMODE no ---------- --- --- --- CdPA LOC LINK SLC TYPE IPLIML2 1301 A 0 IPLIMI M2PA SAPCI 5-067-1 Link set table is (12 of 1024) 1% full.
If the linkset does not meet the criteria shown in the "Adding Linksets for Exception Routes" section, either choose another linkset from the rtrv-ls
output in 5 and repeat this step, or add a new linkset by performing one of these procedures:
rtrv-rtx
command in 1, continue the procedure with 14. rtrv-rtx
command in 1, continue the procedure with 13. rtrv-dstn
command. Note:
If cluster point codes are displayed in thertrv-rtx
orrtrv-rte
outputs, skip this step and continue the procedure with8. This is an example of the possible output.
rlghncxa03w 10-12-10 11:43:04 GMT EAGLE5 43.0.0 Extended Processing Time may be Required DPCA CLLI BEI ELEI ALIASI ALIASN/N24 DMN 002-002-002 ----------- no --- ---------- -------------- SS7 002-002-003 ----------- no --- ---------- -------------- SS7 003-003-003 ----------- no --- ---------- -------------- SS7 004-004-004 ----------- no --- ---------- -------------- SS7 005-005-005 ----------- no --- ---------- -------------- SS7 006-006-006 ----------- no --- ---------- -------------- SS7 DPCI CLLI BEI ELEI ALIASA ALIASN/N24 DMN 1-234-5 ----------- no --- -------------- -------------- SS7 2-145-6 ----------- no --- -------------- -------------- SS7 0-123-7 ----------- no --- -------------- -------------- SS7 3-025-6 ----------- no --- -------------- -------------- SS7 1-100-5 ----------- no --- -------------- -------------- SS7 4-139-4 ----------- no --- -------------- -------------- SS7 5-067-1 ----------- no --- -------------- -------------- SS7 DPCN CLLI BEI ELEI ALIASA ALIASI DMN 00002 ----------- no --- -------------- ---------- SS7 00003 ----------- no --- -------------- ---------- SS7 00004 ----------- no --- -------------- ---------- SS7 09852 ----------- no --- -------------- ---------- SS7 11211 ----------- no --- -------------- ---------- SS7 11302 ----------- no --- -------------- ---------- SS7 12567 ----------- no --- -------------- ---------- SS7 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 12 TOTAL DPC(s): 32 CAPACITY (% FULL): 2% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
If a cluster point code is not shown in the rtrv-dstn
output, continue the procedure with 12.
If a cluster point code is shown in the rtrv-dstn
output, and the DPC of the exception route is not a member of a cluster point code, continue the procedure with 12.
If a cluster point code is shown in the rtrv-dstn
output, and the DPC of the exception route is a member of a cluster point code, continue the procedure with 8.
rtrv-dstn
command with the cluster point code. For this example, enter this command.
rtrv-dstn:dpca=010-010-*
This is an example of the possible output.
rlghncxa03w 10-12-10 11:43:04 GMT EAGLE5 43.0.0 DPCA CLLI BEI ELEI ALIASI ALIASN/N24 DMN 010-010-* ----------- no no ---------- -------------- SS7 SPCA NCAI RCAUSE NPRST SPLITIAM HMSMSC HMSCP SCCPMSGCNV ----------- yes none off none no no none Destination table is (33 of 2000) 1% full Alias table is (0 of 12000) 0% full
The DPC of an exception route cannot be a member of a cluster point code unless the NCAI
value of the cluster point code is yes
. If the NCAI
value of the cluster point code is yes
, continue the procedure with 12.
If the NCAI
value of the cluster point code is no
, continue the procedure with 9.
rtrv-feat
command. The entry NCR = on
in the rtrv-feat
command output shows that the NCR feature is on.
Note:
Thertrv-feat
command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by thertrv-feat
command, see the rtrv-feat
command description in Commands User's Guide. If the NCR feature is on, continue the procedure with 11.
If the NCR feature is off, continue the procedure with 10.
chg-feat:ncr=on
Note:
Once the NCR feature is turned on with thechg-feat
command, it cannot be turned off.The NCR feature must be purchased before you turn the feature on with the chg-feat
command. If you are not sure if you have purchased the NCR feature, contact your Sales Representative or Account Representative.
When this command has successfully completed, this message should appear.
rlghncxa03w 06-10-10 11:43:04 GMT EAGLE5 38.0.0 CHG-FEAT: MASP A - COMPLTD
NCAI
value for the cluster point code from no to yes by entering the chg-dstn
command with the cluster point code and the ncai=yes
parameter. For this example, enter this command. chg-dstn:dpca=010-010-*:ncai=yes
.
When this command has successfully completed, this message should appear.
rlghncxa03w 08-02-11 15:35:05 GMT EAGLE5 38.0.0 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 12 NETWORK DPC(s): 0 CLUSTER DPC(s): 1 TOTAL DPC(s): 33 CAPACITY (% FULL): 1% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0% X-LIST ENTRIES ALLOCATED: 500 CHG-DSTN: MASP A - COMPLTD
Note:
If theopc
/opca
parameter will not be specified with theent-rtx
command, continue the procedure with12. opc
/opca
value of the exception route can be specified with the network cluster and network cluster member values of the point code as asterisks (*). If the network cluster and network cluster member values of the opc
/opca
value will not be specified as asterisks, continue the procedure by performing one of the steps shown at the end of this step.
If the network cluster and network cluster member values of the opc
/opca
value will be specified as asterisks, and the network indicator value of the opc
/opca
value is 6 or greater, continue the procedure by performing one of the steps shown at the end of this step.
If the network cluster and network cluster member values of the opc
/opca
value will be specified as asterisks, and the network indicator value of the opc
/opca
value will be 1 through 5, the PCTYPE
value shown in the rtrv-sid
output must be OTHER
. Enter the rtrv-sid
command to verify the PCTYPE
value.
This is an example of the possible output.
rlghncxa03w 06-10-10 11:43:04 GMT EAGLE5 38.0.0 PCA PCI PCN CLLI PCTYPE 001-001-001 1-001-1 00001 rlghncxa03w OTHER CPCA 002-002-004 002-002-005 002-002-006 002-002-007 002-002-008 002-002-009 004-002-001 004-003-003 050-060-070 CPCI 1-001-2 1-001-3 1-001-4 1-002-1 1-002-2 1-002-3 1-002-4 2-001-1 7-222-7 CPCN 00050 00060 00070 00100 00080 00090
If the PCTYPE
value shown in the rtrv-sid
output is OTHER
, continue the procedure by performing one of the steps shown at the end of this step.
If the PCTYPE
value shown in the rtrv-sid
output is ANSI
, Change the PCTYPE
value of the self-identification of the EAGLE to OTHER
by performing the Changing the Self-Identification of the EAGLE procedure. After the PCTYPE
value is changed, continue the procedure by performing one of the steps shown at the end of this step.
rtrv-rtx
command in 1, continue the procedure with 14. rtrv-rtx
command in 1, continue the procedure with 13. lsn
parameter value), the 6-Way Loadsharing on Routesets feature must be enabled and turned on. To verify the status of the 6-Way Loadsharing on Routesets feature, enter this command.
rtrv-ctrl-feat:partnum=893019801
The following is an example of the possible output.
rlghncxa03w 09-05-28 21:15:37 GMT EAGLE5 41.0.0 The following features have been permanently enabled: Feature Name Partnum Status Quantity 6-Way LS on Routesets 893019801 on ---- The following features have been temporarily enabled: Feature Name Partnum Status Quantity Trial Period Left Zero entries found. The following features have expired temporary keys: Feature Name Partnum Zero entries found.
If the 6-Way Loadsharing on Routesets feature is not enabled or not turned on, perform the Activating the 6-Way Loadsharing on Routesets Feature procedure to enable and turn on the 6-Way Loadsharing on Routesets feature.
After the 6-Way Loadsharing on Routesets feature has been enabled and turned on, or if the rtrv-ctrl-feat
output shows that the 6-Way Loadsharing on Routesets feature is enabled and turned on, continue this procedure with 14.
ent-rtx
command and specifying the parameter combinations shown in Table 3-27 for the exception route criteria being assigned to the exception route. Table 3-27 Add Exception Route Parameter Combinations
OPC- Based Exception Lists | ILSN- Based Exception Lists | SI- Based Exception Lists | Single CIC- Based Exception Lists | Range of CICs- Based Exception Lists |
---|---|---|---|---|
:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the |
:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the |
:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the |
:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the |
:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the |
:opc/opca/ opci/opcn/ opcn24 = OPC value of the exception route (See Notes 5, 6, and 9) |
:ilsn = incoming linkset name shown in the |
:si = service indicator, 3 - 15 |
:cic = circuit identification code, 0 - 16383 (See Note 8) |
:cic = the circuit identification code value beginning a range of CICs, 0 - 16383 (See Note 8) |
:lsn = linkset name shown in the |
:lsn = linkset name shown in the |
:lsn = linkset name shown in the |
:lsn = linkset name shown in the |
:ecic = the circuit identification code value ending a range of CICs, 0 - 16383 (See Notes 7 and 8) |
:rc = 0 - 99 |
:rc = 0 - 99 |
:rc = 0 - 99 |
:rc = 0 - 99 |
:lsn = linkset name shown in the |
:force=yes (See Note 6) |
:force=yes (See Note 6) |
:rc = 0 - 99 |
||
Notes: 1. The DPC of an exception route entry can contain only a maximum of two entries with the same RC value and with either the same OPC value, the same ILSN value, the same SI value, the same CIC value, or range of CIC values if the 6-Way Loadsharing on Routesets feature is not enabled or turned on. If the 6-Way Loadsharing on Routesets feature is enabled and turned on, the DPC of an exception route entry can contain more than two entries with the same RC value and with either the same OPC value, the same ILSN value, the same SI value, the same CIC value, or range of CIC values, the LSN value for each entry must be different. 2. Each DPC can contain a maximum of six entries with either the same OPC value, the same ILSN value, the same SI value, or the same range of CIC values. The LSN value for each entry must be different. If the 6-Way Loadsharing on Routesets feature is not enabled or turned on, the DPC of a route exception entry can contain only one entry with a single CIC value. If the 6-Way Loadsharing on Routesets feature is enabled and turned on, the DPC of a route exception entry can contain more than one entry with a single CIC value. 4. The linksets specified in this step must meet the criteria shown in the "Adding Linksets for Exception Routes" section. 5. The DPC value cannot be the same as the OPC value. 6. The 7. The 8. The range of CIC values cannot overlap an existing range of CIC values. A single CIC value cannot be within a range of CIC values provisioned for another exception route entry. The 9. Asterisks can be used as the values for the network cluster and network cluster member portions of an ANSI point code value for the |
For this example, enter these commands.
ent-rtx:dpca=006-006-006:opca=125-150-175:lsn=lsn11:rc=10
ent-rtx:dpca=006-006-006:opci=2-103-1:lsn=lsn11:rc=20
ent-rtx:dpca=006-006-006:ilsn=lsn12:lsn=lsn11:rc=11
ent-rtx:dpca=006-006-006:ilsn=lsn13:lsn=lsn11:rc=12
ent-rtx:dpca=006-006-006:si=5:lsn=lsn12:rc=10
ent-rtx:dpca=006-006-006:cic=250:lsn=lsn12:rc=15
ent-rtx:dpca=006-006-006:cic=300:ecic=500:lsn=lsn12:rc=25
ent-rtx:dpci=3-025-6:opca=135-102-089:lsn=lsn13:rc=10
ent-rtx:dpci=3-025-6:opci=4-054-0:lsn=lsn13:rc=15
ent-rtx:dpci=3-025-6:opcn=00503:lsn=lsn13:rc=45
ent-rtx:dpci=3-025-6:ilsn=lsn2:lsn=lsn14:rc=20
ent-rtx:dpci=3-025-6:ilsn=lsn4:lsn=lsn13:rc=25
ent-rtx:dpci=3-025-6:ilsn=lsn16:lsn=lsn16:rc=50:force=yes
ent-rtx:dpci=3-025-6:si=3:lsn=lsn13:rc=30
ent-rtx:dpci=3-025-6:cic=100:lsn=lsn14:rc=35
ent-rtx:dpci=3-025-6:cic=50:ecic=75:lsn=lsn13:rc=40
ent-rtx:dpcn=09852:opca=127-063-048:lsn=lsn15:rc=10
ent-rtx:dpcn=09852:opci=3-037-1:lsn=lsn16:rc=15
ent-rtx:dpcn=09852:opcn=00409:lsn=lsn13:rc=20
ent-rtx:dpcn=09852:ilsn=lsn13:lsn=lsn15:rc=25
ent-rtx:dpcn=09852:ilsn=lsn4:lsn=lsn16:rc=30
ent-rtx:dpcn=09852:si=4:lsn=lsn15:rc=35
ent-rtx:dpcn=09852:cic=1000:lsn=lsn16:rc=40
ent-rtx:dpcn=09852:cic=2000:ecic=3000:lsn=lsn15:rc=45
When each of these commands have successfully completed, this message should appear.
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 ENT-RTX: MASP A - COMPLTD
rtrv-rtx
command, specifying these parameters depending on the exception route criteria specified in 14. opc
/opca
/opci
/opcn
/opcn24
parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx
command – dpc
/dpca
/dpci
/dpcn
/dpcn24
, opc
/opca
/opci
/opcn
/opcn24
, and lsn
. ilsn
parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx
command – dpc
/dpca
/dpci
/dpcn
/dpcn24
, ilsn
, and lsn
. si
parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx
command – dpc
/dpca
/dpci
/dpcn
/dpcn24
, si
, and lsn
. cic
parameter was specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx
command – dpc
/dpca
/dpci
/dpcn
/dpcn24
, cic
, and lsn
. cic
and ecic
parameters were specified in 14 - enter these parameters and values specified in 14 with the rtrv-rtx
command – dpc
/dpca
/dpci
/dpcn
/dpcn24
, cic
, ecic
, and lsn
. For this example, enter these commands.
rtrv-rtx:dpca=006-006-006:opca=125-150-175:lsn=lsn11
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCA RTX-CRITERIA LSN RC APC 006-006-006 OPCA 125-150-175 lsn11 10 004-004-004 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:opci=2-103-1:lsn=lsn11
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCA RTX-CRITERIA LSN RC APC 006-006-006 OPCI 2-103-1 lsn11 20 004-004-004 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:ilsn=lsn12:lsn=lsn11
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCA RTX-CRITERIA LSN RC APC 006-006-006 ILSN lsn12 lsn11 11 004-004-004 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:ilsn=lsn13:lsn=lsn11
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCA RTX-CRITERIA LSN RC APC 006-006-006 ILSN lsn13 lsn11 12 004-004-004 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:si=5:lsn=lsn12
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCA RTX-CRITERIA LSN RC APC 006-006-006 SI 5 lsn12 10 005-005-005 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:cic=250:lsn=lsn12
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCA RTX-CRITERIA LSN RC APC 006-006-006 CIC - ECIC 250 250 lsn12 15 005-005-005 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpca=006-006-006:cic=300:ecic=500:lsn=lsn12
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCA RTX-CRITERIA LSN RC APC 006-006-006 CIC - ECIC 250 250 lsn12 15 005-005-005 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:opca=135-102-089:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCI RTX-CRITERIA LSN RC APC 3-025-6 OPCA 135-102-089 lsn13 10 1-100-5 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:opci=4-054-0:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCI RTX-CRITERIA LSN RC APC 3-025-6 OPCI 4-054-0 lsn13 15 1-100-5 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:opcn=00503:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCI RTX-CRITERIA LSN RC APC 3-025-6 OPCN 00503 lsn11 15 1-100-5 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:ilsn=lsn2:lsn=lsn14
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCI RTX-CRITERIA LSN RC APC 3-025-6 ILSN lsn2 lsn14 45 4-139-4 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:ilsn=lsn4:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCI RTX-CRITERIA LSN RC APC 3-025-6 ILSN lsn4 lsn13 25 1-100-5 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:ilsn=lsn16:lsn=lsn16
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCI RTX-CRITERIA LSN RC APC 3-025-6 ILSN lsn16 lsn16 50 12567 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:si=3:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCI RTX-CRITERIA LSN RC APC 3-025-6 SI 3 lsn13 30 1-100-5 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:cic=100:lsn=lsn14
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCI RTX-CRITERIA LSN RC APC 3-025-6 CIC - ECIC 100 100 lsn14 35 4-139-4 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpci=3-025-6:cic=50:ecic=75:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCI RTX-CRITERIA LSN RC APC 3-025-6 CIC - ECIC 50 75 lsn13 40 1-100-5 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:opca=127-063-048:lsn=lsn15
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCN RTX-CRITERIA LSN RC APC 09852 OPCA 127-063-048 lsn15 10 11302 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:opci=3-037-1:lsn=lsn16
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCN RTX-CRITERIA LSN RC APC 09852 OPCI 3-037-1 lsn16 15 12567 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:opcn=00409:lsn=lsn13
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCN RTX-CRITERIA LSN RC APC 09852 OPCN 00409 lsn13 20 1-100-5 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:ilsn=lsn13:lsn=lsn15
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCN RTX-CRITERIA LSN RC APC 09852 ILSN lsn13 lsn15 25 11302 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:ilsn=lsn4:lsn=lsn16
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCN RTX-CRITERIA LSN RC APC 09852 ILSN lsn4 lsn16 30 12567 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:si=4:lsn=lsn15
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCN RTX-CRITERIA LSN RC APC 09852 SI 4 lsn15 35 11302 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:cic=1000:lsn=lsn16
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCN RTX-CRITERIA LSN RC APC 09852 CIC - ECIC 1000 lsn16 40 12567 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
rtrv-rtx:dpcn=09852:cic=2000:ecic=3000:lsn=lsn15
rlghncxa03w 08-02-11 08:28:30 GMT EAGLE5 38.0.0 DPCN RTX-CRITERIA LSN RC APC 09852 CIC - ECIC 2000 3000 lsn15 45 11302 DESTINATION ENTRIES ALLOCATED: 2000 FULL DPC(s): 20 EXCEPTION DPC(s): 36 TOTAL DPC(s): 56 CAPACITY (% FULL): 3% ALIASES ALLOCATED: 12000 ALIASES USED: 0 CAPACITY (% FULL): 0%
chg-db:action=backup:dest=fixed
command. These messages should appear, the active Maintenance and Administration Subsystem Processor (MASP) appears first.
BACKUP (FIXED) : MASP A - Backup starts on active MASP. BACKUP (FIXED) : MASP A - Backup on active MASP to fixed disk complete. BACKUP (FIXED) : MASP A - Backup starts on standby MASP. BACKUP (FIXED) : MASP A - Backup on standby MASP to fixed disk complete.
Figure 3-45 Adding an Exception Route Entry
Sheet 1 of 10
Sheet 2 of 10
Sheet 3 of 10
Sheet 4 of 10
Sheet 5 of 10
Sheet 6 of 10
Sheet 7 of 10
Sheet 8 of 10
Sheet 9 of 10
Sheet 10 of 10