Removing a Route Exception Entry

This procedure is used to remove an exception route from the database using the dlt-rtx command. The dlt-rtx command uses these parameters.

:dpc/dpca/dpci/dpcn/dpcn24 – The destination point code of the node that the traffic is being sent to.

:opc/opca/opci/opcn/opcn24 – The originating point code of the node sending traffic to the EAGLE.

:ilsn – The name of the linkset carrying incoming traffic to the EAGLE.

:lsn – The name of the linkset carrying the traffic to the node specified by the destination point code.

:si – The service indicator value assigned to the exception route.

:cic – The circuit identification code value assigned to an exception route containing a single CIC entry or the CIC value that begins a range of CICs assigned to the exception route.

:ecic – The circuit identification code value that ends the range of CICs assigned to the exception route.

:all – This parameter, along with the force=yes parameter, allows all the exception routes containing the exception route criteria, OPC, ILSN, SI, CIC, CIC and ECIC, to be removed from the database. This parameter has only one value, yes.

:force – This parameter, along with the all=yes parameter, allows all the exception routes containing the exception route criteria, OPC, ILSN, SI, CIC, CIC and ECIC, to be removed from the database. This parameter has only one value, yes.

The values of all the parameters specified for the dlt-rtx command, except the all=yes and force=yes parameters, must be shown in the rtrv-rtx output and must be assigned to the specified dpc/dpca/dpci/dpcn/dpcn24 value.

The combinations of these parameters that can be used with the dlt-rtx command are shown in Table 3-28.

Display the exception routes in the database by entering the rtrv-rtx command. This is an example of the possible output.

rlghncxa03w 06-10-07 11:43:04 GMT  EAGLE5 36.0.0

   DPCA          RTX-CRITERIA              LSN        RC    APC

   003-003-003   OPCA
                 009-009-009               lsn1       3     002-002-002
                 010-010-010               lsn1       2     002-002-002
                 010-010-010               lsn2       10    002-002-003

                 ILSN
                 lsn3                      lsn2       2     002-002-003
                 lsn4                      lsn2       1     002-002-003
                 lsn4                      lsn1       10    002-002-002

                 CIC - ECIC
                 15    15                  lsn2       1     002-002-003
                 17    17                  lsn2       7     002-002-003
                 17    17                  lsn1       10    002-002-002
                 18    30                  lsn1       8     002-002-002
                 18    30                  lsn2       10    002-002-003

                 SI
                 3                         lsn2       5     002-002-003
                 3                         lsn1       10    002-002-002
                 5                         lsn2       5     002-002-003

   006-006-006   OPCA
                 125-150-175               lsn11      10    004-004-004

                 OPCI
                 2-103-1                   lsn11      20    004-004-004

                 ILSN
                 lsn12                     lsn11      11    004-004-004
                 lsn13                     lsn11      12    004-004-004

                 CIC - ECIC
                 250   250                 lsn12      15    005-005-005
                 300   500                 lsn12      25    005-005-005

                 SI
                 5                         lsn12      10    005-005-005

   DPCI          RTX-CRITERIA              LSN        RC    APC

   0-123-7       OPCI
                 1-222-3                   lsn3       10    1-234-5
                 1-222-4                   lsn3       11    1-234-5
                 1-222-5                   lsn4       11    2-145-6

   3-025-6       OPCA
                 135-102-089               lsn13      10    1-100-5

                 OPCI
                 4-054-0                   lsn13      15    1-100-5

                 OPCN
                 00503                     lsn11      15    1-100-5

                 ILSN
                 lsn2                      lsn14      45    4-139-4
                 lsn4                      lsn13      25    1-100-5
                 lsn16                     lsn16      50    12567

                 CIC - ECIC
                 100   100                 lsn14      35    4-139-4
                 50    75                  lsn13      40    1-100-5

                 SI
                 3                         lsn13      30    1-100-5

   DPCN          RTX-CRITERIA              LSN        RC    APC
   09852         OPCA
                 127-063-048               lsn15      10    11302

                 OPCI
                 3-037-1                   lsn16      15    12567

                 OPCN
                 00409                     lsn13      20    1-100-5

                 ILSN
                 lsn13                     lsn15      25    11302
                 lsn4                      lsn16      30    12567

                 CIC - ECIC
                 1000  1000                lsn16      40    12567
                 2000  3000                lsn15      45    11302

                 SI
                 4                         lsn15      35    11302

DESTINATION ENTRIES ALLOCATED:   2000
    FULL DPC(s):                   20
    EXCEPTION DPC(s):              41
    TOTAL DPC(s):                  61
    CAPACITY (% FULL):              3%
ALIASES ALLOCATED:               12000
    ALIASES USED:                   0
    CAPACITY (% FULL):              0%

Remove the exception route entry by entering the dlt-rtx command and specifying the parameter combinations shown in Table 3-28 for the exception route criteria being assigned to the exception route.

Table 3-28 Remove Exception Route Parameter Combinations

Exception Route Criteria
:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the `rtrv-rtx` output	:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the `rtrv-rtx` output	:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the `rtrv-rtx` output	:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the `rtrv-rtx` output	:dpc/dpca/ dpci/dpcn/ dpcn24 = DPC of the exception route shown in the `rtrv-rtx` output
:opc/opca/ opci/opcn/ opcn24 = OPC value of the exception route assigned to the DPC value	:ilsn = incoming linkset name of the exception route assigned to the DPC value	:si = service indicator value of the exception route assigned to the DPC value	:cic = circuit identification code value of the exception route assigned to the DPC value	:cic = the circuit identification code value beginning a range of CICs of the exception route assigned to the DPC value
:lsn = linkset name of the exception route assigned to the DPC value (See Notes)	:lsn = linkset name of the exception route assigned to the DPC value (See Notes)	:lsn = linkset name of the exception route assigned to the DPC value (See Notes)	:lsn = linkset name shown of the exception route assigned to the DPC value (See Notes)	:ecic = the circuit identification code value ending a range of CICs of the exception route assigned to the DPC value
:force=yes (See Notes)	:force=yes (See Notes)	:force=yes (See Notes)	:force=yes (See Notes)	:lsn = linkset name shown of the exception route assigned to the DPC value (See Notes)
:all=yes (See Notes)	:all=yes (See Notes)	:all=yes (See Notes)	:all=yes (See Notes)	:force=yes (See Notes)
				:all=yes (See Notes)
Note: The `all=yes` and `force=yes` parameter cannot be specified with the `lsn` parameter. If the `all=yes` parameter is specified, the `force=yes` parameter must be specified. If the exception route entry being removed contains only one entry for the specified exception route criteria, the `all=yes` and `force=yes` parameters can be specified, but do not have to be specified. If the `all=yes` and `force=yes` parameters are not specified, the `lsn` parameter must be specified.

For this example, enter these commands to remove a single entry for a specific exception route criteria.

dlt-rtx:dpca=003-003-003:opca=010-010-010:lsn=lsn1

dlt-rtx:dpca=003-003-003:ilsn=lsn4:lsn=lsn2

dlt-rtx:dpca=003-003-003:cic=17:lsn=lsn2

dlt-rtx:dpca=003-003-003:cic=18:ecic=30:lsn=lsn2

dlt-rtx:dpca=003-003-003:si=3:lsn=lsn1

To remove all the entries for a specific exception route criteria, for this example enter these commands.

dlt-rtx:dpca=003-003-003:opca=010-010-010:all=yes:force=yes

dlt-rtx:dpca=003-003-003:ilsn=lsn4:all=yes:force=yes

dlt-rtx:dpca=003-003-003:cic=17:all=yes:force=yes

dlt-rtx:dpca=003-003-003:cic=18:ecic=30:all=yes:force=yes

dlt-rtx:dpca=003-003-003:si=3:all=yes:force=yes

When each of these commands have successfully completed, this message should appear.

rlghncxa03w 06-10-07 08:28:30 GMT  EAGLE5 36.0.0
DLT-RTX: MASP A - COMPLTD

Verify the changes using the rtrv-rtx command, specifying these parameters depending on the parameters specified in 2.

If the ilsn and lsn parameters were specified in 2 - enter these parameters and values specified in 2 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, ilsn, and lsn.
If the si and lsn parameters were specified in 2 - enter these parameters and values specified in 2 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, si, and lsn.
If only the cic and lsn parameters were specified in 2 - enter these parameters and values specified in 2 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, cic, and lsn.
If the cic and ecic and lsn parameters were specified in 2 - enter these parameters and values specified in 2 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, cic, ecic, and lsn.
If the opc/opca/opci/opcn/opcn24, all=yes, and force=yes parameters were specified in 2 - enter these parameters and values specified in 2 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24 and opc/opca/opci/opcn/opcn24.
If the ilsn, all=yes, and force=yes parameters were specified in 2 - enter these parameters and values specified in 2 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24 and ilsn.
If the si, all=yes, and force=yes parameters were specified in 2 - enter these parameters and values specified in 2 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24 and si.
If only the cic, all=yes, and force=yes parameters were specified in 2 - enter these parameters and values specified in 2 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24 and cic.
If the cic, ecic, all=yes, and force=yes parameters were specified in 2 - enter these parameters and values specified in 2 with the rtrv-rtx command – dpc/dpca/dpci/dpcn/dpcn24, cic, and ecic.

For this example, if a single entry for the specified exception route criteria was removed in step 2, enter these commands.

rtrv-rtx:dpca=003-003-003:opca=010-010-010:lsn=lsn1

rlghncxa03w 06-10-07 08:28:30 GMT  EAGLE5 36.0.0

DESTINATION ENTRIES ALLOCATED:   2000
    FULL DPC(s):                   20
    EXCEPTION DPC(s):              31
    TOTAL DPC(s):                  51
    CAPACITY (% FULL):              3%
ALIASES ALLOCATED:               12000
    ALIASES USED:                   0
    CAPACITY (% FULL):              0%

rtrv-rtx:dpca=003-003-003:ilsn=lsn4:lsn=lsn2

rlghncxa03w 06-10-07 08:28:30 GMT  EAGLE5 36.0.0

DESTINATION ENTRIES ALLOCATED:   2000
    FULL DPC(s):                   20
    EXCEPTION DPC(s):              31
    TOTAL DPC(s):                  51
    CAPACITY (% FULL):              3%
ALIASES ALLOCATED:               12000
    ALIASES USED:                   0
    CAPACITY (% FULL):              0%

rtrv-rtx:dpca=003-003-003:cic=17:lsn=lsn2

rlghncxa03w 06-10-07 08:28:30 GMT  EAGLE5 36.0.0

DESTINATION ENTRIES ALLOCATED:   2000
    FULL DPC(s):                   20
    EXCEPTION DPC(s):              31
    TOTAL DPC(s):                  51
    CAPACITY (% FULL):              3%
ALIASES ALLOCATED:               12000
    ALIASES USED:                   0
    CAPACITY (% FULL):              0%

rtrv-rtx:dpca=003-003-003:cic=18:ecic=30:lsn=lsn2

rlghncxa03w 06-10-07 08:28:30 GMT  EAGLE5 36.0.0
DESTINATION ENTRIES ALLOCATED:   2000
    FULL DPC(s):                   20
    EXCEPTION DPC(s):              31
    TOTAL DPC(s):                  51
    CAPACITY (% FULL):              3%
ALIASES ALLOCATED:               12000
    ALIASES USED:                   0
    CAPACITY (% FULL):              0%

rtrv-rtx:dpca=003-003-003:si=3:lsn=lsn1

rlghncxa03w 06-10-07 08:28:30 GMT  EAGLE5 36.0.0
DESTINATION ENTRIES ALLOCATED:   2000
    FULL DPC(s):                   20
    EXCEPTION DPC(s):              31
    TOTAL DPC(s):                  51
    CAPACITY (% FULL):              3%
ALIASES ALLOCATED:               12000
    ALIASES USED:                   0
    CAPACITY (% FULL):              0%

For this example, if multiple entries for a specific exception route criteria were removed in step 2, enter these commands.

rtrv-rtx:dpca=003-003-003:opca=010-010-010

rlghncxa03w 06-10-07 08:28:30 GMT  EAGLE5 36.0.0

DESTINATION ENTRIES ALLOCATED:   2000
    FULL DPC(s):                   20
    EXCEPTION DPC(s):              26
    TOTAL DPC(s):                  46
    CAPACITY (% FULL):              2%
ALIASES ALLOCATED:               12000
    ALIASES USED:                   0
    CAPACITY (% FULL):              0%

rtrv-rtx:dpca=003-003-003:ilsn=lsn4

rlghncxa03w 06-10-07 08:28:30 GMT  EAGLE5 36.0.0

DESTINATION ENTRIES ALLOCATED:   2000
    FULL DPC(s):                   20
    EXCEPTION DPC(s):              26
    TOTAL DPC(s):                  46
    CAPACITY (% FULL):              2%
ALIASES ALLOCATED:               12000
    ALIASES USED:                   0
    CAPACITY (% FULL):              0%

rtrv-rtx:dpca=003-003-003:cic=17

rlghncxa03w 06-10-07 08:28:30 GMT  EAGLE5 36.0.0

DESTINATION ENTRIES ALLOCATED:   2000
    FULL DPC(s):                   20
    EXCEPTION DPC(s):              26
    TOTAL DPC(s):                  46
    CAPACITY (% FULL):              2%
ALIASES ALLOCATED:               12000
    ALIASES USED:                   0
    CAPACITY (% FULL):              0%

rtrv-rtx:dpca=003-003-003:cic=18:ecic=30

rlghncxa03w 06-10-07 08:28:30 GMT  EAGLE5 36.0.0

DESTINATION ENTRIES ALLOCATED:   2000
    FULL DPC(s):                   20
    EXCEPTION DPC(s):              26
    TOTAL DPC(s):                  46
    CAPACITY (% FULL):              2%
ALIASES ALLOCATED:               12000
    ALIASES USED:                   0
    CAPACITY (% FULL):              0%

rtrv-rtx:dpca=003-003-003:si=3

rlghncxa03w 06-10-07 08:28:30 GMT  EAGLE5 36.0.0

DESTINATION ENTRIES ALLOCATED:   2000
    FULL DPC(s):                   20
    EXCEPTION DPC(s):              26
    TOTAL DPC(s):                  46
    CAPACITY (% FULL):              2%
ALIASES ALLOCATED:               12000
    ALIASES USED:                   0
    CAPACITY (% FULL):              0%

Back up the new changes using the chg-db:action=backup:dest=fixed command. These messages should appear, the active Maintenance and Administration Subsystem Processor (MASP) appears first.

BACKUP (FIXED) : MASP A - Backup starts on active MASP.
BACKUP (FIXED) : MASP A - Backup on active MASP to fixed disk complete.
BACKUP (FIXED) : MASP A - Backup starts on standby MASP.
BACKUP (FIXED) : MASP A - Backup on standby MASP to fixed disk complete.

Figure 3-46 Removing a Route Exception Entry

Sheet 1 of 5

Sheet 2 of 5

Sheet 3 of 5

Sheet 4 of 5

Sheet 5 of 5