5 Debug Commands
This chapter contains information about debug commands used in troubleshooting and debugging the system. These commands are intended only for My Oracle Support (MOS) personnel and authorized engineering personnel in the operating companies. The use of these commands is restricted to personnel who have access to the command class Debug.
CAUTION: These commands are to be used precisely as they are described in this chapter, and only under the direction of Customer Care Center personnel. Any other use of these commands can result in a system failure.
This chapter contains the debug commands in alphabetical order.
act-gedti
Use this command to activate a GEDTI Hub for Eagle Eyes. The state of the GEDTI Hub is changed from DACT(Deactivated) to ACT(Active).
Note:
The GEDTI hub must be Deactived on the specified card before the command can be executed. If the card boots, then the status of the GEDTI Hub will be reset to DACT.Parameters
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
Example
act-gedti:loc=1102
Dependencies
The value specified for the loc parameter must refer to an equipped card location.
The card at the specified location must be configured as GEDTI Hub.
Activating the state of GEDTI Hub that is already activated has no effect.
The card at the specified location must not be a reserved location.
Notes
None.
Output
act-gedti:loc=1101
Command Accepted - Processing
tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0 act-gedti:loc=1101
Command entered at terminal #1.;
tekelecstp 11-08-16 18:35:44 MST
UNKNOWN EAGLE 46.0.0 Activate GEDTI Hub message sent to card.;
tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0
Command Completed.;
Related Topics
act-ip-lnk
Use this command to activate an IP link and put the link into service. The state of the link is changed from OOS-MT-DSBLD (Out-Of-Service-Maintenance-Disabled) to OOS-MT (Out-Of-Service-Maintenance), IS-ANR (In-Service-Abnormal) or IS-NR (In-Service-Normal).
Note:
The specified card must be Active before the command can be executed. If the card boots, then the status of the IP link will be reset.Parameters
- loc (mandatory)
- The card location as stenciled on the shelf of the
system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1113, 1115
Example
act-ip-lnk:loc=1102:port=a
act-ip-lnk:loc=1203:port=fca
act-ip-lnk:loc=1103:port=c
act-ip-lnk:loc=1202:port=d
Dependencies
The value specified for the loc parameter must refer to one of the following cards, and the referenced card must be equipped:
- E5-ENET-B card running the EROUTE, IPGWx, IPLIMx, IPSG, or STPLAN application
- IPSM card
- E5-SM4G or E5-SM8G-B card running the VSCCP application
- E5-OAM card running the OAMHC application
- E5-MCPM-B
- SLIC card
A valid value must be specified for the loc parameter.
- port A - E5-OAM card running OAMHC application, IPSM card, E5-MCPM-B card, E5-ENET-B card running the STPLAN application
- port A, B - E5-ENET-B card running the EROUTE or IPLIMx application, E5-SM4G or E5-SM8G-B card running the VSCCP application
- port A, B, FCA, FCB - E5-ENET-B card running the IPGWx or IPSG application
- port A, B, C and D are valid for SIP/ENUM/DEIR application running on SLIC card.
The card at the specified location must be configured.
The card in the specified location must be Active before this command can be executed.
Notes
The act-ip-lnk/dact-ip-lnk commands were created as debug means - aids to turn off or disable the IP interface to troubleshoot network problems, specifically to allow the operator to troubleshoot IP network flooding issues that can cause EAGLE cards to boot repeatedly while trying to come up. These commands should NOT be used for general maintenance actions since they have not been rigorously tested and their usage should be limited to situations like described above.
Interface A/D is used for ExAP connectivity and interface B/C is used for the signaling network on the SLIC card running the SIP/ENUM/DEIR application.
Output
act-ip-lnk:loc=1101:port=a
Command Accepted - Processing
tekelecstp 11-08-16 19:52:01 MST EAGLE 44.0.0
act-ip-lnk:loc=1101:port=a
Command entered at terminal #1.
;
tekelecstp 11-08-16 19:52:01 MST EAGLE 44.0.0
Activate IP link message sent to card.
;
tekelecstp 11-08-16 19:52:01 MST EAGLE 44.0.0
Command Completed.
;
act-ip-lnk:loc=1103:port=c
Command Accepted - Processing
tekelecstp 16-05-25 03:48:33 MST EAGLE 46.4.0.0.0-69.1.0
act-ip-lnk:loc=1103:port=c
Command entered at terminal #18.
;
tekelecstp 16-05-25 03:48:33 MST EAGLE 46.4.0.0.0-69.1.0
Activate IP link message sent to card.
;
tekelecstp 16-05-25 03:48:33 MST EAGLE 46.4.0.0.0-69.1.0
Command Completed.
;
act-upgrade
Use this command to perform a software upgrade from a source release to the target release on an in-service system.
Caution:
It is strongly recommended that this command be used only in conjunction with the system Upgrade Procedure for your target release. The Upgrade Procedure provides step-by-step information on performing an upgrade.Parameters
- action (mandatory)
- The action to be performed for the upgrade
process.
Caution:
The convertoam and netcomplete actions should be used only under the direction of My Oracle Support (MOS).- Range:
- yyyyyyyyyy
Up to 10 alphabetic characters. Valid actions are:
- chkrel—Validates the stored upgrade target release on the physical disk as specified by the src parameter.
- convertoam—Converts the standby OAM database.
- convertstp—Performs all OAM and network conversions necessary for an upgrade. This command transitions through all of the upgrade phases to upgrade completion. If measurement collection is turned on, this command automatically inhibits measurements during the upgrade. Upon completion of the upgrade, this command returns the MASPs to full-function mode with measurement collection turned back on.
- createsets—Assigns network cards to upgrade-grouping sets.
-
dbstatus—Reports the status of all database partitions on the TDM
fixed disks and the removable drive(s) (similar to the
rept-stat-db:display=versioncommand). - displaysets—Reports the upgrade-grouping sets of network cards.
- getrel—Retrieves the upgrade target release file from either the EAGLE software release distribution server or the plug-in flash drive. It then expands the data on the inactive partition group of the hard disks.
- netcomplete—Indicates upgrade completion and places the system in a fully functional mode.
- oamcomplete—Sets the upgrade phase number to 3, and enables the beginning of controlled card loading.
- refreshsets—Not yet supported.
- verifysets—Verifies that the card set list is consistent with the current EAGLE configuration and displays detailed information on any inconsistencies found.
- force (optional)
- Allows the user to override Card Set List verification and perform upgrade when only minor inconsistencies are present.
- release (optional)
- The name of the software release file to be
downloaded.
This file contains the upgrade target release on the software release distribution server or plug-in flash drive.
- Range:
-
xyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
1 alphabetic character followed by up to 29 alphanumeric characters. One or more periods can be used.
Note:
The value must be at least 11 characters in length and must contain a hyphen (-). The format of the value must be xx.xx.xx-yy.yy.yy, where xx.xx.xx is the release number, and yy.yy.yy is the engineering build number.
Example
act-upgrade:action=convertstp
act-upgrade:action=dbstatus
act-upgrade:action=convertstp:thres=75
act-upgrade:action=getrel:release="46.7.0.0.0-74.2.0.tar.gz":src=usb
act-upgrade:action=chkrel:src=fixed
Dependencies
The value specified for the action parameter must correspond to a specific upgrade phase:
- action=convertoam—upgrade phase=0 and 1
- action=oamcomplete—upgrade phase=2
- action=convertnet—upgrade phase=3
- action=netcomplete—upgrade phase=3
- action=convertstp—upgrade phase=0-3
The Measurements Collection function must be turned off
(chg-meas:collect=off) or the Measurements
Platform feature must be turned on (chg-measopts:platformenable=on) before a value of
convertoam,
oamcomplete, or
netcomplete can be specified for the
action parameter.
A valid upgrade release must reside on the plug-in flash drive or the inactive partition of the fixed disk.
The standby OAM database must be the source release.
The current OAM database must be the source release.
The database partition must be coherent.
The database partition must be in the correct functional mode.
The action=convertstp and thres parameters must be specified together in the command.
Upgrade conversion cannot be initiated from a telnet-type terminal (terminal IDs 17-40).
The DCM cards are obsolete for SS7IPGW, IPGWI, IPLIM, and IPLIMI applications.
The action=getrel and release parameters must be specified together in the command.
An IPSM card must be provisioned and in service before a value of getrel or chkrel can be specified for the action parameter.
The
ent-ftp-serv:app=dist
command must be entered before a value of
getrel or
chkrel can be specified for the
action parameter.
The act-upgrade:action=convertstp cannot be issued with any removable media inserted in any of the USB ports.
Invalid hardware configuration alarms are set or an HMUX alarm must be addressed.
All cards that are in the auto-inhibited state must be removed before this command can be entered.
Cards that prevent the IMT buses from being inhibited during the upgrade cannot exist in the system.
The specified source drive must be at the correct database version for the upgrade to proceed.
The plug-in flash drive cannot contain an EAGLE backup image.
If the src=usb parameter is selected, then the plug-in flash drive upgrade media must be inserted in the Active OAM's flush-mounted USB port.
The internal RAM disk must be available for the plug-in flash drive's upgrade image to be unpackaged.
The disk that contains the upgrade target release must be in a known upgrade mode.
If the src=usb or src=server parameter is specified, then the action=getrel parameter must be specified. If the src=fixed parameter is specified, then the action=getrel parameter cannot be specified.
The EAGLE PVN address in the source database cannot be identical to the EAGLE FCNA or FCNB network address in the target database.
The icdpnunknx and icdpnunknX and the gcdpnunknx and gcdpnunknX NPP Action Sets cannot co-exist in the source release.
The value specified for the release parameter must be at least 11 characters in length and contain a hyphen (-). The format of the value must be xx.xx.xx-yy.yy.yy, where xx.xx.xx is the release number, and yy.yy.yy is the engineering build number.
The card must have sufficient DRAM memory to perform the GTMOD table Health Check.
The AMGTT data in the GTT table cannot exceed the capacity of the GTMOD table (100 K).
Unable to access GTT table from source drive.
The MFC feature must be ON prior to upgrading to release 46.2 or later.
The action=refreshsets and action=verifysets parameters are not supported.
The thres parameter cannot be specified if the threshold type (threstype) has been changed to set.
When issuing the
act-upgrade command with the threstype
assigned to card sets, the list of card sets needs to be created and valid.
When issuing the act-upgrade command with the threstype assigned to Card Set, the card set list must be consistent with the current EAGLE configuration, unless force=yes is allowed and specified. Details of any such inconsistencies and recovery instructions will be reported in a similar manner as act-upgrade:action=verifysets.
The act-upgrade command cannot be issued when SFAPP(P)->OAM sync
is ON.
This command cannot be entered when CAT2 IPSM to OAM syncing is in progress.
Notes
The
act-upgrade:action=convertstp command
executes all four upgrade phases consecutively.
If the
act-upgrade:action=convertstp command
is entered following a command abort, the upgrade processing determines the
last upgrade phase that was successfully completed. The upgrade processing then
attempts to restart from that point to successful completion. Re-entering the
act-upgrade:action=convertstp command
following a command abort is the recommended method for recovery.
The TDMs and plug-in flash drives have upgrade phase indicators. The upgrade command expects the disks to be in certain phases before executing a specific action. If the disks are not in the correct phases, an error is generated.
The
act-upgrade:action=dbstatus command
generates output similar to that provided by the
rept-stat-db:display=version command.
The thres parameter is used to:
- Allow multiple cards to be upgraded together, as
long as the specified percentage of links remains in service. The value is
applied to groups of links based upon the link-supporting group or the entire
system. The grouping is set by the
chg-upgrade-config:threstype=command. - Enable SCCP thresholding, which allows multiple Service Module cards to be upgraded together. The specified thres parameter value is not used to determine the number of Service Module cards to upgrade. The peak SCCP load since the last OAM boot is used to determine the number of cards that must remain in service (at least half of the cards must remain in service).
- Enable the non-provisioned flash function, which flash-downloads any boot-prom type card if the card is in the system but not provisioned.
The
act-upgrade:action=getrel action
defaults to getting the release from the provisioned IPSM card using the
provisioned FTP Server. If the
src=usb parameter is specified, then
the release is obtained from the plug-in USB flash drive upgrade media.
Output
Note:
Theact-upgrade:action=convertstp command
performs the OAM conversion and the network conversion. During the
conversion, this command broadcasts the current activity in the scroll area.
Refer to Appendix B of the EAGLE Release Software Upgrade Procedure for a
sample of message output.
The action dbstatus reports the current database status.
act-upgrade:action=dbstatus
eaglestp 15-02-13 11:45:51 MST EAGLE5 45.0.1-64.70.35 Upg Phase 0
DATABASE STATUS: >> OK <<
TDM 1114 ( STDBY) TDM 1116 ( ACTV )
C LEVEL TIME LAST BACKUP C LEVEL TIME LAST BACKUP
- -------- ---------------------- - -------- ----------------------
FD BKUP Y 210 - - Y 210 - -
FD CRNT Y 210 Y 210
MCAP 1113 MCAP 1115
- -------- - --------
RD BKUP - - - - - - - -
USB BKP - - - - - - - -
CARD/APPL LOC C T LEVEL TIME LAST UPDATE VERSION STATUS
--------- ---- - - ---------- ----------------- -------------------
OAM-RMV 1113 - - - - - -
TDM-CRNT 1114 Y N 210 15-01-16 12:22:02 135-000-000 NORMAL
TDM-BKUP 1114 Y - 210 15-01-16 12:22:02 135-000-000 NORMAL
OAM-RMV 1115 - - - - - -
OAM-USB 1115 - - - - - -
TDM-CRNT 1116 Y N 210 15-01-16 12:22:02 135-000-000 NORMAL
TDM-BKUP 1116 Y - 210 15-01-16 12:22:02 135-000-000 NORMAL
INACTIVE PARTITION GROUP
CARD/APPL LOC C T LEVEL TIME LAST UPDATE VERSION STATUS
--------- ---- - - ---------- ----------------- -------------------
TDM-CRNT 1114 N - 1 00-00-00 00:00:00 136-000-000 NORMAL
TDM-BKUP 1114 N - 1 00-00-00 00:00:00 136-000-000 NORMAL
TDM-CRNT 1116 Y - 1 00-00-00 00:00:00 136-000-000 NORMAL
TDM-BKUP 1116 Y - 1 00-00-00 00:00:00 136-000-000 NORMAL
;
chg-bip-fld
Use this command to manually update the board identification PROM (BIP) data during an upgrade in the field.
Note:
Initial programming of the BIP data occurs during manufacturing.Parameters
Example
This example shows changing of the sm (Software MatchID) field in BIP data of Main assembly:
chg-bip-fld:loc=1102:fld=sm:data="001"Dependencies
The value of the loc parameter cannot specify a location for a fixed disk or removable drive.
Notes
The card in the specified location must be inhibited.
Output
chg-bip-fld:loc=1103:fld=rev:data="B"
tekelecstp 10-04-01 12:05:44 IST EAGLE 42.0.0
Board ID Prom updated.
;
chg-bip-rec
Use this command to manually update the Board Identification PROM (BIP) data during an upgrade in the field.
Note:
Initial programming of the BIP data occurs during manufacturing.Parameters
Example
This example initializes the contents of a main assembly BIP to contain only the record specified in the data parameter:
chg-bip-rec:loc=1105:data=xxxx:init=yes
This example displays the programming of the DCM Ethernet Addresses for Port A (ENT01):
chg-bip-rec:loc=1102:data="ENT01,AD00001704000D,cs104"Dependencies
The value of the loc parameter cannot specify a location for a fixed disk or removable drive.
If the init=yes parameter is specified, then the value of the data parameter must be a Board IDentification (BID) record.
Notes
The card in the specified location must be inhibited.
Output
chg-bip-rec:loc=1107:data=xxx:init=yes
tekelecstp 10-04-01 12:05:44 IST EAGLE 42.0.0
Board ID Prom updated.
;
chg-ee-card
Parameters
Use this command to enter/modify Eagle Eyes Network card data in the Eagle Eyes Card (EE CARD) table. The EE CARD entry consists of Card location and Eagle Eyes specific data.
- loc (mandatory)
- Eagle Eyes Card location.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
- fltid (optional)
- A comma-separated Eagle Eyes Filter ID list to be associated or disassociated with the card. Up to 8 FLT IDs can be specified in the list.
Example
chg-ee-card:loc=1101:fltid=12:action=attach:thr=2000:pktlim=5000
chg-ee-card:loc=1102:kblim=40000:seclim=3000000
chg-ee-card:loc=1101:fltid=13:action=detach:pktlim=none
Dependencies
If the fltid parameter is specified, then the action parameter must be specified.
The EE CARD table cannot contain more than 256 entries.
The EE CARD table must be accessible.
At least one optional parameter must be specified.
The fltid specified should not be already associated with the card.
The value specified for the fltid parameter must already exist in the EE FLT table.
Maximum of 16 include filters can be attached to a card.
Maximum of 16 exclude filters can be attached to a card.
The value specified for the loc parameter must not be a system reserved location.
The IMT table must be accessible.
The card in the location specified by the loc parameter must have Eagle Eyes service capability.The card loc specified to detach a filter must have Eagle Eyes configured.
The card at the specified location must be equipped.
The Filter appl and card appl should be same.
Notes
- IPSG, IPLHC, IPGHC
- ATMHC
- SS7HC
- SIPHC
- DEIRHC
Output
chg-ee-card:loc=1101:fltid=12:action=attach:thr=2000:pktlim=5000
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
EE CARD table is (2 of 256) 1% full
CHG-EE-CARD: MASP A - COMPLTD
Related Topics
chg-gedti-card
Use this command to configure GEDTI Hub for Eagle Eyes traffic capture.
Parameters
- loc (mandatory)
- IPSM Card location to be configured as GEDTI Hub.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
Example
chg-gedti-card:loc=1211:port=1124
Dependencies
The value specified for the loc parameter must correspond to the location of an IPSM card.
The value specified for the port parameter must not be configured on any other IPSM card.
If the GEDTI Hub is in ACTIVE state then port cannot be changed.
The EE Card table must be accessible.
Notes
None.
Output
chg-gedti-card:loc=1211:port=1245
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
EE CARD table is (2 of 256) 1% full
CHG-GEDTI-CARD:MASP A - COMPLTD ;
Related Topics
chg-tbl
Use this command to create, rename, or reset any table on a fixed disk or removable drive.
Caution:
Before entering thechg-tbl command, contact My Oracle
Support.
Parameters
Example
chg-tbl:action=create:disk=remove:name=test:ext=sys:filelength=150000
chg-tbl:action=reset:disk=remove:id=0
chg-tbl:action=rename:disk=remove:id=0:name=dms:ext=old
Dependencies
If the action=create/rename parameter is specified, then the name parameter must be specified.
If the action=create parameter is specified, then the name, ext, and filelength parameters must be specified.
If the file type is a directory, the filelength parameter is not required. The directory entry file length is always 1 cluster in length.
The attributes used during file creation are current date and time of the active MASP. Readable/writable files are allocated contiguously from the last free FAT cluster.
If the action=reset parameter is specified, then the id parameter must be specified.
If the action=rename parameter is specified, then the id, name, and ext parameters must be specified.
This command cannot be used to modify the security log.
Notes
None
Output
chg-tbl:action=create:disk=remove:name=test:ext=sys:filelength=150000
chg-tbl: CREATE 0K : filename = test.sys, byte length = 150000
chg-tbl: command complete
;
chg-tbl:action=reset:disk=remove:id=0
chg-tbl: RESET OK : Table 0, DMS.CFG
chg-tbl: command complete
;
chg-tbl:action=rename:disk=remove:id=0:name=dms:ext=old
chg-tbl: RENAME 0K : Table 0, DMS.CFG to DMS.OLD
chg-tbl: command complete
;
Related Topics
chg-upgrade-config
Note:
This command stores data that will be used during the software upgrade. The command does not start the software upgrade.Parameters
- addtblcnv (optional)
- This parameter sets the flag of the corresponding entry in the Table Conversion Definition table that forces the table to be converted during a software upgrade.
Caution:
The addtblcnv parameter should be used only under the direction of My Oracle Support (MOS).
- assignset (optional)
- Assigned Set. The card specified by the loc parameter is assigned to the upgrade-grouping set specified by this parameter.
- deltblcnv (optional)
- This parameter clears the flag of the corresponding entry in the Table Conversion Definition table that forces the table to be converted during a software upgrade.
Caution:
The deltblcnv parameter should be used only under the direction of My Oracle Support (MOS).
- loc (optional)
- Location. The location of a network card to be assigned to a set specified by the assignset parameter.
Example
chg-upgrade-config:addtblcnv=327
chg-upgrade-config:deltblcnv=327
chg-upgrade-config:sak=vbjyapdpbtejb:src=fixed
chg-upgrade-config:threstype=set:srvsets=2:limsets=4
Dependencies
The addtblcnv and deltblcnv parameters cannot be specified together in the command.
One of the optional parameters must be specified in the command.
The srvsets and limsets parameters cannot be specified unless the threstype is being changed to or has been changed to set.
The loc parameter is required when the assignset parameter is specified.
The value specified for the assignset parameter cannot be greater than the current value of srvsets or limsets for the specified card.
The chg-upgrade-config command cannot be issued when SFAPP(P)->OAM
sync is ON.
This command cannot be entered when CAT2 IPSM to OAM syncing is in progress.
Output
chg-upgrade-config:addtblcnv=327
rlghncxa03w 07-03-13 08:15:45 EST EAGLE 37.5.0
Command Completed.
;
Related Topics
clr-disk-stats
Use this command to clear the disk performance statistics. All associated disk statistics are zeroed.
Example
clr-disk-stats:loc=1113
Dependencies
The specified card location must contain a card that is running an OAM (1113 or 1115).
A related command must not be in progress.
Notes
None
Output
clr-disk-stats:loc=1113
rlghncxa03w 01-03-01 14:14:05 EST Rel 28.1.0
Disk performance statistics cleared.
;
Related Topics
copy-tbl
Use this command to copy a single table from one source to another. A table can be copied to any verifiable location in the system; however, the source and destination tables must have identical configurations (same number of entries, same entry size, both 1- dimensional and 2-dimensional).
Note:
A table cannot be copied onto itself.Parameters
- dloc (mandatory)
- Destination location. The location of the
destination table.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
- sloc (mandatory)
- Source location. The location of the source table.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
Example
copy-tbl:stbl=25:dtbl=24:sloc=1114:dloc=1116:sdrv=fixed
Dependencies
Only one table copy command can be executed at a time.
The source and destination tables must exist and be compatible.
This command cannot be used to modify the security log.
The same value cannot be specified for the sloc and dloc or the stbl and dtbl parameters.
If a value of fixed is specified for the sdrv or ddrv parameter, then a value of 1114 or 1116 must be specified for the sloc or dloc parameter.
This command cannot be entered when CAT2 IPSM to OAM syncing is in progress.
Notes
None
Output
copy-tbl:stbl=25:dtbl=24:sloc=1114:dloc=1116:sdrv=fixed
rlghncxa03w 01-03-04 16:11:53 EST Rel 28.1.0
Table copy command complete.
;
dact-ee
Use this command to deactivate an Eagle Eyes Card and stop capturing traffic on it. The state of the card is changed from ACT (Active) to DACT (Deactivated).
Note:
If the card boots, then the status of the card would be reset to DACT. This will clear the EE configuration from the card.Parameters
- loc (mandatory)
- The Eagle Eyes card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
Example
dact-ee:loc=1203
Dependencies
The card at the specified location must be equipped.
The card should be configured as an Eagle Eyes card.
Notes
- IPSG, IPLHC, IPGHC
- ATMHC
- SS7HC
- SIPHC
- DEIRHC
- ERTHC
Output
dact-ee:loc=1101
Command Accepted - Processing
tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0
dact-ee:loc=1101
Command entered at terminal #1.
;
tekelecstp 11-08-16 18:35:44 MST UNKNOWN EAGLE 46.0.0
Deactivate EE message sent to card.
;
tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0
Command Completed.
;
Related Topics
dact-gedti
Use this command to deactivate a GEDTI Hub. The state of the GEDTI Hub is changed from ACT (Active) to DACT (Deactivated).
Note:
The specified card must be Active before the command can be executed. If the card boots, then the status of the GEDTI Hub will be reset to DACT.Parameters
- loc (mandatory)
- The card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1113, 1115
Example
dact-gedti:loc=1102
Dependencies
The value specified for the loc parameter must refer to an equipped card location.
A valid value must be specified for the loc parameter.
The card at the specified location must be configured as a GEDTI Hub.
Deactivating the state of a GEDTI Hub that is already deactivated has no effect.
Notes
None.
Output
dact-gedti:loc=1101
Command Accepted - Processing
tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0
dact-gedti:loc=1101
Command entered at terminal #1.
;
tekelecstp 11-08-16 18:35:44 MST UNKNOWN EAGLE 46.0.0
Deactivate GEDTI Hub message sent to card.
;
tekelecstp 11-08-16 18:35:44 MST EAGLE 46.0.0
Command Completed.;Related Topics
dact-ip-lnk
Use this command to deactivate an IP link and put the link out of service. The state of the link is changed from IS-NR (In-Service-Normal), IS-ANR (In-Service-Abnormal), or OOS-MT (Out-Of-Service-Maintenance), to OOS-MT-DSBLD (Out-Of-Service-Maintenance-Disabled).
Note:
The specified card must be Active before the command can be executed. If the card boots, then the status of the IP link will be reset.Parameters
- loc (mandatory)
- The card location as stenciled on the shelf of the
system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1113, 1115
Example
dact-ip-lnk:loc=1102:port=a
dact-ip-lnk:loc=1203:port=fca
dact-ip-lnk:loc=1103:port=c
dact-ip-lnk:loc=1202:port=d
Dependencies
The value specified for the loc parameter must refer to one of the following cards, and the referenced card must be equipped:
- E5-ENET-B card running the EROUTE, IPGWx, IPLIMx, IPSG, or STPLAN application
- IPSM card
- E5-SM4G or E5-SM8G-B card running the VSCCP application
- E5-OAM card running the OAMHC application
- E5-MCPM-B card
- SLIC card
A valid value must be specified for the loc parameter.
- port A-E5-OAM card running OAMHC application, IPSM card, E5-MCPM-B card, E5-ENET-B card running the STPLAN application
- port A, B- E5-ENET-B card running the EROUTE or IPLIMx application, E5-SM4G or E5-SM8G-B card running the VSCCP application
- port A, B, FCA, FCB- E5-ENET-B card running the IPGWx or IPSG application
- ports A, B, C and D are valid for DEIR/SIP/ENUM applications running on SLIC card
The card at the specified location must be configured.
The card in the specified location must be Active before this command can be executed.
Notes
The act-ip-lnk/dact-ip-lnk commands were created as debug means - aids to turn off or disable the IP interface to troubleshoot network problems, specifically to allow the operator to troubleshoot IP network flooding issues that can cause EAGLE cards to boot repeatedly while trying to come up. These commands should NOT be used for general maintenance actions since they have not been rigorously tested and their usage should be limited to situations like described above.
Interface A/D is used for ExAP connectivity and interface B/C is used for the signaling network on the SLIC card running DEIR/SIP/ENUM applications.
Output
dact-ip-lnk:loc=1101:port=a
Command Accepted - Processing
tekelecstp 11-08-16 18:35:44 MST EAGLE 44.0.0
dact-ip-lnk:loc=1101:port=a
Command entered at terminal #1.
;
tekelecstp 11-08-16 18:35:44 MST UNKNOWN EAGLE 44.0.0
Deactivate IP link message sent to card.
;
tekelecstp 11-08-16 18:35:44 MST EAGLE 44.0.0
Command Completed.
; dact-ip-lnk:loc=1103:port=c
Command Accepted - Processing
tekelecstp 16-05-25 03:51:03 MST EAGLE 46.4.0.0.0-69.1.0
dact-ip-lnk:loc=1103:port=c
Command entered at terminal #18.
;
tekelecstp 16-05-25 03:51:03 MST EAGLE 46.4.0.0.0-69.1.0
Deactivate IP link message sent to card.
;
tekelecstp 16-05-25 03:51:03 MST EAGLE 46.4.0.0.0-69.1.0
Command Completed.
;
Related Topics
dbg-ddb
Use this command to display the checksum, statistics, and wild write audit (WWA) updates of dynamic database (DDB) table entries, audit a specific table, and reset the DDB statistics on the cards.
Parameters
- action (mandatory)
- The action taken by the command.
- Range:
-
- stats
- display dynamic database statistics
- aud
- audit a specific table
- disp
- display a table entry
- wwa
- display any entries updated by WWA task
- rststat
- reset following DDB audit statistics:
- Number of DDB updates
- Number of consecutive DDB update in progress
- Maximum DDB updates in 100 msec
- Idle period
- Maximum and minimum idle period
- audtype (optional)
- Audit type. This parameter specifies whether a unicast or multicast audit is performed.
- dpc (optional)
- The destination point code value. The Route table entry corresponding to the DPC value is displayed.
- Range:
- p-, 000-255, *
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
prefix—p-
The asterisk value (*) is not valid for the ni subfield.
When
chg-sid:pctype=ansiis specified, ni = 000 is not valid.When
chg-sid:pctype=ansiis specified, nc = 000 is not valid if ni = 001–005.When
chg-sid:pctype=ansiis specified, nc = 000 is valid if ni = 006–255.The point code 000-000-000 is not a valid point code.
- dpci (optional)
- ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-zone-area-id).
- dpcn (optional)
- ITU national destination point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the
chg-stpopts:npcfmtiflexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- dpcn24 (optional)
- 24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp). The prefix subfield indicates a private point code (prefix-msa-ssa-sp).
- dpcn16 (optional)
- 16-bit ITU national point code with subfields unit number sub number area main number area (un-sna-mna). The prefix subfield indicates a private point code (prefix-un-sna-mna).
- loc (optional)
- The location of the MTP card that is being debugged.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
- lsn (optional)
- Linkset name. The entry in the Linkset table that corresponds to the specified linkset name.
- rloc (optional)
- Reference card location. This parameter audits the table where the reference card is located.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
Example
This command displays the 126th entry in the Link table.dbg-ddb:loc=1105:tbl=lnk:action=disp:tidx=126
This command displays the entry in the Link table corresponding to link=a and rloc=1107.dbg-ddb:loc=1105:tbl=lnk:action=disp:rloc=1107:link=a
This command audits the Link table in multicast mode.dbg-ddb:loc=1105:tbl=lnk:action=aud:audtype=mc
This command audits the Link table in unicast mode.dbg-ddb:loc=1105:tbl=lnk:action=aud:audtype=uc
This command audits the Link table at the card location 1105 using the reference card 1107.dbg-ddb:loc=1105:tbl=lnk:action=aud:audtype=uc:rloc=1107
This command displays the statistics of a specified card.dbg-ddb:loc=1201:action=stats
This command displays the WWA entries on a specified card.dbg-ddb:action=wwa:loc=1201
This command resets the statistics of a specified card.dbg-ddb:action=rststat:loc=2100
This command resets the statistics of all active MTP cards.
dbg-ddb:action=rststat
Dependencies
The dpc, tidx, lsn, and rloc parameters cannot be specified together in the command.
The dpc, tidx, lsn, and link parameters cannot be specified together in the command.
The action=disp and tbl=rte parameters must be specified before the dpc parameter can be specified.
The action=disp and tbl=ls parameters must be specified before the lsn parameter can be specified.
The action=disp and tbl=lnk parameters must be specified before the link parameter can be specified.
The action=disp parameter must be specifed before the tidx parameter can be specified.
The action= aud parameter must be specified before the audtype parameter can be specified.
The action=disp and tbl=lnk parameters or the action=aud and audtype=uc parameters must be specified before the rloc parameter can be specified.
If the action parameter has a value of wwa, stats, or rststat, then the loc parameter is the only other parameter that can be specified.
If the action=disp and tbl=lnk parameters are specified, then the rloc and link parameters must be specified together in the command.
The card location specified by the loc or rloc parameter must be equipped.
The value specified for the loc or rloc parameter must indicate an MTP card.
The status of the card at the location specified by the loc or rloc parameter must be active.
The linkset specified by the lsn parameter must already exist in the Linkset table.
The link specified by the link parameter must already be equipped.
The value specified for the dpc parameter must already exist in the Route table.
The Link table is corrupt or cannot be found.
The value specified for the dpc parameter must be a full point code, network point code, or a cluster point code.
Values of 1113 - 1118 cannot be specified for the loc or rloc parameters.
If the action parameter has a value of disp, aud, stats, or wwa, then the loc parameter must be specified.
If the action=aud parameter and the rloc parameter are specified, then the audtype parameter must be specified.
If the action parameter has a value of disp or aud, then the tbl parameter must be specified.
The J7 support feature must be enabled before the opcn16/dpcn16 parameters can be specified.
Notes
For a multicast audit, the card that receives the message sends the audit request to all other MTP cards simultaneously. For a unicast audit, the card that receives the message sends the audit request to another MTP card, which sends the request to next MTP card, etc. This process continues until the last MTP card in the system receives the request.
A maximum of the last 10 entries of WWA updates are displayed.
Output
A maximum of 20 entries with mismatched card values can be displayed as necessary.
If mismatched card entries occur, the SeqNo field can be used to correlate the entries between two cards (e.g.SeqNo: 1 of card 1 can be compared against SeqNo: 1 of card 2.)
dbg-ddb:loc=1104:action=disp:tbl=ls:tidx=1
tekelecstp 09-10-15 12:37:37 EST EAGLE5 41.1.0
dbg-ddb:loc=1104:action=disp:tbl=ls:tidx=1
Command entered at terminal #4.
;
tekelecstp 09-10-15 12:37:37 EST EAGLE5 41.1.0
User Message sent to location 1104.
;
tekelecstp 09-10-15 12:37:37 EST EAGLE5 41.1.0
[SeqNo: 0] [1104] [Linkset:1] Chksum h'1624 at h'28e84a (138 bytes)
Assign:1 Avail:0 APC: 001-001-002 ITUNVar:0
;
dbg-ddb:loc=1104:action=disp:tbl=lnk:tidx=1
tekelecstp 09-10-15 12:37:37 GMT EAGLE5 41.1.0
dbg-ddb:loc=1104:action=disp:tbl=lnk:tidx=1
Command entered at terminal #4.
;
tekelecstp 09-10-15 12:37:37 GMT EAGLE5 41.1.0
User Message sent to location 1104.
;
tekelecstp 09-10-15 12:37:37 GMT EAGLE5 41.1.0
[SeqNo: 0] [1104] [Link:x1] Chksum h'da8d at h'2877ce (14 bytes)
PortId:h'1e6 (Card:1104 Link h'0)
Slc:0 Stat:h'2 LsId:h'0 Class:0
Status:Fail
;
dbg-ddb:loc=1104:action=aud:tbl=lnk:audtype=mc
tekelecstp 09-10-15 13:40:38 GMT EAGLE5 41.1.0
dbg-ddb:loc=1104:action=aud:tbl=lnk:audtype=mc
Command entered at terminal #4.
;
tekelecstp 09-10-15 13:40:38 GMT EAGLE5 41.1.0
User Message sent to location 1104.
;
tekelecstp 09-10-15 13:40:38 GMT EAGLE5 41.1.0
[1104] Bcast:Card->Sys (Tbl 0) MTPCards:h'2 Reply:h'2 Mismatch:h'0
;
dbg-ddb:loc=1104:action=aud:tbl=lnk:audtype=uc
tekelecstp 09-10-15 16:37:11 GMT EAGLE5 41.1.0
dbg-ddb:loc=1104:action=aud:tbl=lnk:audtype=uc
Command entered at terminal #4.
;
tekelecstp 09-10-15 16:37:11 GMT EAGLE5 41.1.0
User Message sent to location 1104.
;
tekelecstp 09-10-15 16:37:11 GMT EAGLE5 41.1.0
[1104]Card->System (Tbl:0) Successful System Audit Completed
;
This example shows the output when multiple mismatch entries occur between two cards:
dbg-ddb:loc=1205:rloc=1207:action=aud:tbl=rte:audtype=uc
tekelecstp 10-01-28 16:37:11 GMT EAGLE5 42.0.0
dbg-ddb:loc=1205:rloc=1207:action=aud:tbl=rte:audtype=uc
Command entered at terminal #4.
;
tekelecstp 10-01-28 16:37:11 GMT EAGLE5 42.0.0
User Message sent to location 1205.
;
tekelecstp 10-01-28 16:37:11 GMT EAGLE5 42.0.0
Card[1205]->card[1207] (Tbl:0) TblAuditDone:TotalMisses:h'2 FirstMiss:h'0
;
tekelecstp 10-01-28 16:37:11 GMT EAGLE5 42.0.0
[SeqNo: 1] [1205] [Route:h'0] Chksum h'320b at h'8fc3b0 (75 bytes)
PC: 001-001-001 LstRt:0 CmbRt:6 Dyn:h'1 TFC:0
Xlst:0 MOBR:0 NAdj:1 3 3 3 3 3 NmTFR:0 PrevSt:1
;
tekelecstp 10-01-28 16:37:11 GMT EAGLE5 42.0.0
[SeqNo: 1] [1205] nway: 0 cost_grp(0-5): c7 c6 c6 c6 c6 c6
rte_used(0-5): c0 36 36 36 36 36
curr_cost_grp: 0 prev_cost_grp 0
SRT:h'88079c (28 bytes) AKT:h'8bb43c (12 bytes)
;
tekelecstp 10-01-28 16:37:11 GMT EAGLE5 42.0.0
[SeqNo: 2] [1205] [Route:h'1] Chksum h'c96e at h'8fc3fb (75 bytes)
PC: 001-001-002 LstRt:0 CmbRt:6 Dyn:h'1 TFC:0
Xlst:0 MOBR:0 NAdj:1 3 3 3 3 3 NmTFR:0 PrevSt:1
;
tekelecstp 10-01-28 16:37:11 GMT EAGLE5 42.0.0
[SeqNo: 2] [1205] nway: 0 cost_grp(0-5): c7 c6 c6 c6 c6 c6
rte_used(0-5): c0 36 36 36 36 36
curr_cost_grp: 0 prev_cost_grp 0
SRT:h'8807b8 (28 bytes) AKT:h'8bb448 (12 bytes)
;
tekelecstp 10-01-28 16:37:11 GMT EAGLE5 42.0.0
[SeqNo: 1] [1207] [Route:h'0] Chksum h'cecc at h'9688ea0 (243 bytes)
PC: 001-001-001 LstRt:0 CmbRt:6 Dyn:h'1 TFC:0
Xlst:0 MOBR:0 NAdj:1 3 3 3 3 3 NmTFR:0 PrevSt:1
;
tekelecstp 10-01-28 16:37:11 GMT EAGLE5 42.0.0
[SeqNo: 1] [1207] nway: 0 cost_grp(0-5): c8 c6 c6 c6 c6 c6
rte_used(0-5): c0 46 36 36 36 36
curr_cost_grp: 0 prev_cost_grp 0
SRT:h'95148e0 (28 bytes) AKT:h'9575980 (12 bytes)
;
tekelecstp 10-01-28 16:37:11 GMT EAGLE5 42.0.0
[SeqNo: 2] [1207] [Route:h'1] Chksum h'662f at h'9688f93 (243 bytes)
PC: 001-001-002 LstRt:0 CmbRt:6 Dyn:h'1 TFC:0
Xlst:0 MOBR:0 NAdj:1 3 3 3 3 3 NmTFR:0 PrevSt:1
;
tekelecstp 10-01-28 16:37:11 GMT EAGLE5 42.0.0
[SeqNo: 2] [1207] nway: 0 cost_grp(0-5): c8 c6 c6 c6 c6 c6
rte_used(0-5): c0 46 36 36 36 36
curr_cost_grp: 0 prev_cost_grp 0
SRT:h'95148fc (28 bytes) AKT:h'957598c (12 bytes)
;
dbg-ddb:action=wwa:loc=1301
tekelecstp 09-10-12 17:37:11 GMT EAGLE5 41.1.0
dbg-ddb:action=wwa:loc=1301
Command entered at terminal #10.
;
tekelecstp 09-10-12 17:37:11 GMT EAGLE5 41.1.0
User Message sent to location 1301.
;
tekelecstp 09-10-12 17:37:11 GMT EAGLE5 41.1.0
DDB WWA REPORT (LOC = 1301)
WILD WRITE AUDIT UPDATED (1) ENTRIES:
TIME STAMP TABLE ENTRY_IDX ORIG CHKSUM UPD CHKSUM
1. 09-10-12 17:35:02:586 RTE 0 H'41880000 H'00000000
;
dbg-ddb:action=stats:loc=1201
tekelecstp 09-10-03 17:37:11 GMT EAGLE5 41.1.0
dbg-ddb:action=stats:loc=1201
Command entered at terminal #10.
;
tekelecstp 09-10-03 17:37:11 GMT EAGLE5 41.1.0
User Message sent to location 1201.
;
tekelecstp 09-10-03 17:37:11 GMT EAGLE5 41.1.0
DDB STATISTICS
LOC : 1201
CARD STATUS (DDL) : [CROSSLOADED]
(DDB) : [INITIALIZED]
IN UPDATE STATUS (DDB CHECKSUM) : [FALSE]
(TSRC) : [IDLE]
SUCCESIVE TIMES CARD REPORTED (IN UPDATE) : 0
DDB UPDATES : 2000
MAXIMUM UPDATES PER 100ms : 900
DDB IDLE PERIOD: : 03:12:30:20:50
MAXIMUM IDLE PERIOD : 02:12:30:20:50
MINIMUM IDLE PERIOD : 01:04:40:10:80
NUMBER OF WWA UPDATED ENTRIES : 4
;
dbg-ddb:action=wwa:loc=1201
tekelecstp 09-10-21 17:37:11 GMT EAGLE5 41.1.0
dbg-ddb:action=wwa:loc=1201
Command entered at terminal #10.
;
tekelecstp 09-10-21 17:37:11 GMT EAGLE5 41.1.0
User Message sent to location 1201.
;
tekelecstp 09-10-21 17:37:11 GMT EAGLE5 41.1.0
DDB WWA REPORT (LOC = 1201)
WILD WRITE AUDIT UPDATED (NO) ENTRIES:
;
Legend
- WWA—Wild Write Audit
- DDB—Dynamic Database
- Time stamp—Card time stamp when the checksum was detected and updated by wild write audit. The time stamp is inYY-MM-DD hh:mm:ss:msec format.
- TABLE—Table where the checksum is being performed
- Entry Idx—Index of entry that is updated by wild write audit
- Orig Chksum—Original Checksum
- Upd Chksum—Checksum after update by wild write audit
- Idle Period—Time elapsed, in milliseconds, since the last DDB update was received by this card. All idle periods are displayed indd:hh:mm:ss:msec format.
- Number of WWA Updated Entries—Number of entries updated by the WWA
Related Topics
disp-bip
Use this command to display the Board Identification PROM (BIP) hex and ASCII data for the specified card type and location. The PROM data consists of the board ID, part number, revision, date of manufacture, power, serial number, software match ID, and check sums.
Parameters
- loc (mandatory)
- The card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1113, 1115, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110
Example
This example displays the BIP data for the main assembly of the specified card location.
disp-bip:loc=1105Dependencies
The value of the loc parameter cannot specify the location of a fixed disk or removable drive.
Notes
None.
Output
This example displays the BIP data for the main assembly:
disp-bip:loc=1105
tekelecstp 10-03-30 20:24:41 IST EAGLE 42.0.0
Board Identification PROM Dump Location: 1105 - MDB Packet: 1
-------------------------------------------------------------------------
0000 42 49 44 30 31 2c 50 4e 38 37 30 2d 32 32 31 32 BID01,PN870-2212
0010 2d 30 33 2e 45 2c 53 4d 45 47 2e 30 30 31 2c 44 -03.E,SMEG.001,D
0020 53 32 30 30 38 2e 31 34 2e 43 2e 31 30 32 30 38 S2008.14.C.10208
0030 31 34 37 30 39 39 2c 50 57 36 34 36 2c 43 53 32 147099,PW646,CS2
0040 32 35 00 00 01 26 07 ff 01 00 26 00 80 14 21 ff 25...&....&...!.
0050 ff ff 01 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0070 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
;
tekelecstp 10-03-30 20:24:41 IST EAGLE 42.0.0
Board Identification PROM Dump Location: 1105 - MDB Packet: 2
-------------------------------------------------------------------------
0000 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0020 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0030 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0060 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
;
tekelecstp 10-03-30 20:24:41 IST EAGLE 42.0.0
Board Identification PROM Dump Location: 1105 - MDB Packet: 3
-------------------------------------------------------------------------
0000 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0020 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0030 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0060 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
;
tekelecstp 10-03-30 20:24:41 IST EAGLE 42.0.0
Board Identification PROM Dump Location: 1105 - MDB Packet: 4
-------------------------------------------------------------------------
0000 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0020 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0030 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0060 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................
;
Related Topics
disp-bp
Use this command to display currently active breakpoints in the communication and application processors.
Parameters
- card (optional)
- This parameter specifies the card location, in the form of GPLID–Subsystem ID.
- Range: GPLID-Subsystem ID
-
- GPLID
- atmhc, deirhc, erthc, glshc, hipr2, ipghc, iplhc, ipsg, ipshc, mcphc, oamhc, pktgen, sccphc, siphc, slanhc, ss7hc, utility
- Subsystem ID
- a, b, act, stb, all
The oamhc GPL can be specified with any of the subsystem IDs. For all other GPLs, only the all subsystem ID is valid.
- loc (optional)
- The card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115
Example
disp-bp:loc=1109:ueng=3
Dependencies
The loc, imt, or card parameter must be specified.
Only one of the loc, imt, and card parameters can be specified in the command.
The imt parameter allows this command to be entered for a card that has not been configured in the system.
The ueng parameter can be specified only for IXP-based cards.
The oamhc GPLID accepts all subsystem values; all other GPLIDs accept only the all subsystem value.
The card location specified by the loc parameter must be in the database.
Values of 1114, 1116, 1117, and 1118 cannot be specified for the loc parameter.
Notes
None
Output
These examples are for x86-based cards:
disp-bp:card=ss7ansi-all
rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0
SDS Installed Breakpoint Report from IMT Address H'00f4
Brkpoint-Addr Memory-Dump-Addr Condition-1 Condition-2 Repeat-Count
------------- ---------------- ----------- ----------- ------------
H'003a-H'0001 ANY ANY 0
rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0
SDS Installed Breakpoint Report from IMT Address H’000a
BP Address Memory-Dump Address Conditions Rpt Ct Ind
---------- ------------------------- ------------------ ------ ---
H’0000a974 H’000c030c 1- ANY 3 1
Code Breakpoint 2- ANY
H’0000a975 1- ANY PERM 0
Data Write - WORD 2- ANY
H’0000a976 1- ANY 15 0
Any Access - DWORD 2- ANY
H’0000a977 1- ANY PERM 0
Data Read - BYTE 2- ANY
rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0
80386/80486 Debug Registers in Use: DR0 DR2 DR3
;
disp-bp:card=vsccp-all:
rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0
SDS Installed Breakpoint Report from IMT Address H'0005
BP Address Memory-Dump Address Conditions Rpt Ct Ind
---------- ------------------------- ----------------- ------ ---
H'0000a974 1- ANY 1 0
Code Breakpoint 2- ANY
;
These examples are for IXP-based cards:
disp-bp:loc=1109
tekelecstp 05-01-10 13:58:45 GMT EAGLE5 33.0.0
SDS Installed Breakpoint Report from IMT Address H'00ff
BP Address Memory-Dump Address Conditions Rep Ind CPU
---------- ------------------- --------------------- ---- --- ------
H'000401000 R11+H'0000ffff 1- R15 > H'ffffffff 2 0 ARM
Any Access - 2- R0 <= H'0000ffff
Data value: H'00000000 Data Mask: H'ffffffff
disp-bp:loc=1109:ueng=3
tekelecstp 05-01-10 13:58:45 GMT EAGLE 33.0.0
SDS Installed Breakpoint Report from IMT Address H'00ff
BP Address Memory-Dump Address Conditions Rep Ind CPU
---------- ------------------- --------------------- ---- --- ------
H'00235000 H'00020044 1- ANY PERM 1 UENG 3
CODESW Breakpoint 2- ANY CTX 2
;
disp-disk-dir
Use this command to display the DOS directory on the specified disk. This command can display the creation date for each file or for selected files and applies to fixed disks and removable drives.
Note:
This command can be used to verify that the correct version of a file is on the disk.Parameters
Example
disp-disk-dir:loc=1117:file="dms.cfg"
disp-disk-dir:src=remove:file="fta"
disp-disk-dir:src=remove:file="*.*"
Dependencies
Valid filenames must be in the format filename.extension with the following requirements:
- File name—1–8 ASCII Characters
- Extension—0–3 ASCII Characters
Wildcards (asterisks) are allowed when the wildcard pattern is enclosed in parentheses.
- *—Matches all characters in either filename or extension
- ?—Matches one character in either filename or extension
- file=”*.*”—Matches all files on disk
- file=”*.tbl”—Matches all files on disk with .tbl as the extension
The src parameter must be specified.
The 1113 and 1115 locations are used by E5-MCAP cards. The 1114 and 1116 locations are used by E5-TDM cards.
A removable drive must be inserted in the slot indicated by the value specified for the loc or src parameter.
The card specified by the loc parameter must be connected to at least one IMT bus.
Notes
None
Output
disp-disk-dir
lnpstp 01-03-30 15:52:04 EST Rel 28.1.0
DISP-DISK-DIR, Loc=1116, Device = FIXED, Dir = :\
Filename Ext Length Last Modified Cluster LBA
DMS CFG 16384 00-08-01 18:45 2 573
:
File(s) : 175 Bytes : 457956761
Volume : FIXED DISK
Bytes free : 73654887
Disk Size (MB) : 2014
;
disp-disk-dir:loc=1117
lnpstp 01-03-30 15:52:46 EST Rel 28.1.0
disk-disk-dir:loc=1117:file="dms1024.cfg"
DISP-DISK-DIR, Loc=1117, Device = REMOVE, Dir = :\
Filename Ext Length Last Modified Cluster LBA
DMS1024 CFG 16384 00-08-01 15:48 2 339
:
File(s) : 72 Bytes : 192883124
Volume : SYSTEM DISK
Bytes free : 956339788
Disk Size (MB) : 1096
;
disp-disk-dir:file=ttserv.tbl
lnpstp 01-03-30 15:53:09 EST Rel 28.1.0
DISP-DISK-DIR, Loc=1116, Device = FIXED, Dir = :\
Filename Ext Length Last Modified Cluster LBA
TTSERV TBL 8192 00-08-01 18:45 2731 44237
File(s) : 1 Bytes : 8192
Volume : FIXED DISK
Bytes free : 73654887
Disk Size (MB): 2014
;
disp-disk-dir:loc=1116
eaglestp 10-03-06 15:53:09 EST TTTT PPP EAGLE 42.0.0
DISP-DISK-DIR, Loc=1116, Device = FIXED, Dir = :\
Filename Ext Length Last Modified Cluster LBA
DMS CFG 16384 08-07-97 11:00 2 573
OAM ELF 3145728 08-07-97 11:00 4 605
TOAM ELF 3145728 08-07-97 11:00 388 6749
SS7 ELF 1048576 08-07-97 11:00 772 12893
TSS7 ELF 1048576 08-07-97 11:00 900 14941
CCS7ITU ELF 1048576 08-07-97 11:00 1284 21085
.
.
.
LNP_LRN BKP 3072096 08-07-97 11:00 38963 623949
LNP_MR BKP 1679392 08-07-97 11:00 39339 629965
LNP_NPA BKP 5120096 08-07-97 11:00 39545 633261
LNP_4DIG BKP 128000064 08-07-97 11:00 40171 643277
ACG_MIC BKP 187712 08-07-97 11:00 55797 893293
LNP_CHCK BKP 197378 08-07-97 11:00 55820 893661
LNP_DBMM BKP 801600 08-07-97 11:00 55845 894061
TRBLTX BKP 63980 08-07-97 11:00 55943 895629
MTT BKP 384000 08-07-97 11:00 55951 895757
2201800 REL 2048 08-07-97 11:00 55998 896509
File(s) : 175 Bytes : 457956761
Volume : FIXED DISK
Bytes free : 73654887
Disk Size (MB) : 507
Largest Free Space : 73654887
;
This example shows the output when an E5-MCAP card is used:
disp-disk-dir:loc=1113:src=remove
e5oam 09-01-20 22:24:12 EST EAGLE 40.1.0
DISP-DISK-DIR Loc=1113 Dev = REMOVE
Filename Ext Length
DMS1024 CFG 32768
TATMANSI ELF 3145728
TATMHC ELF 5242880
TATMITU ELF 3145728
TBLBEPM ELF 3145728
TBLBIOS ELF 3145728
TBLBSMG ELF 3145728
TBLCPLD ELF 3145728
TBLDIAG ELF 3145728
TBLDIAG6 ELF 3145728
...
SMEAS_ST SYS 12228
UIMLOG SYS 11263947
SYSREL SYS 949
MTT BKP 384000
TRBLTX BKP 96000
FEATCTRL BKP 128000
ASSYPWR BKP 8016
TS30100 REL 5120
BLMCAP TAR 13721600
File(s) : 178 Bytes : 437596655 Disk Size (MB) : 1972;
Legend
- Filename—Name of the file in the directory
- Ext—Extension of the file name (for example, for the file MFC.BIN, MFC is the file name and BIN is the extension of the file name)
- Length—Amount of space, in bytes, the file occupies on the disk
- Last Modified—Date and time the file was changed
- Cluster—A 2-byte, 16-digit binary number that represents the first section of the disk occupied by the file
- LBA—Starting logical block address that corresponds to the cluster
- File(s)—Number of files on the disk that match the search criteria
- Bytes—Amount of space, in bytes, the displayed files occupy on the disk
- Volume—11-character name for the disk
- Bytes free—Number of bytes that are available on the disk for file storage
- Disk Size—Total capacity of the specified disk
disp-disk-stats
Use this command to display the disk performance statistics.
Note:
The OAMs maintain disk read/writer access times as well as per table and per application statistics on the number of disk accesses and cache accesses. Per application and per table statistics that have zero values are not displayed if an application ID or table ID is not specified; only nonzero statistics are displayed in the default report.Example
disp-disk-stats:loc=1113:applid=29
disp-disk-stats:loc=1113:applid=93
disp-disk-stats:loc=1113
Dependencies
The specified card location must contain a card that is running an OAM (1113 or 1115).
GPSM-II and E5-MCAP cards cannot co-exist in the system.
Notes
None
Output
disp-disk-stats:loc=1113:applid=29
rlghncxa03w 01-03-01 14:14:05 EST Rel 28.1.0
Disk Performance Statistics Report:
Cache Read Disk Read Cache Write Disk Write
Appl Id Hits Accesses Hits Accesses
----------- ----------- ----------- ----------- -----------
29 113 23 25 40
Command Completed.
disp-disk-stats:loc=1113:applid=93
tekelecstp 01-06-01 14:14:05 EST Rel 28.1.0
Disk Performance Statistics Report:
Cache Read Disk Read Cache Write Disk Write
Appl Id Hits Accesses Hits Accesses
----------- ----------- ----------- ----------- -----------
93 0 0 0 0
Command Completed.
;
disp-disk-stat:loc=1113
rlghncxa03w 01-03-01 14:14:05 EST Rel 28.1.0
Disk Performance Statistics Report:
Cache Read Disk Read Cache Write Disk Write
Appl Id Hits Accesses Hits Accesses
----------- ----------- ----------- ----------- -----------
29 113 23 25 40
120 12 223 225 361
Cache Read Disk Read Cache Write Disk Write
Table Id Hits Accesses Hits Accesses
----------- ----------- ----------- ----------- -----------
185 12 223 225 361
201 113 23 25 40
Total Cache Total Disk Total Cache Total Disk
Read Hits Reads Write Hits Writes
----------- ----------- ----------- -----------
125 246 250 401
Disk Access Times (microseconds)
Minimum Maximum Average Access Type
----------- ----------- ----------- -----------
1260 31121 6380 Read
1215 31090 6350 Write
Command Completed.
;
Related Topics
disp-mem
Use this command to display memory in communication and application processors. This display is in byte format.
Parameters
- loc (optional)
- The card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115
Example
disp-mem:loc=1204:paddr=h’103abc:bc=8:dformat=word
disp-mem:loc=1204:paddr=h’103abc:bc=8:dformat=dword
disp-mem:card=ss7ansi-all:addr=h'03a-h’001:bc=8
Dependencies
The loc, imt, or card parameter must be specified.
Only one of the loc, imt, and card parameters can be specified in the command.
The card location specified by the loc parameter must be in the database.
All of the subsystem values can be specified with the oamhc GPLID. The other GPLID values can be specified only with the all subsystem value.
Card locations 1114, 1116, 1117, and 1118 are not valid for memory commands.
The GPL specified in the card parameter must be supported.
The addr and paddr parameters cannot be specified together in the command.
Notes
The imt parameter allows this command to be entered for a card that has not been configured in the system.
Output
disp-mem:loc=1204:paddr=h’103abc:bc=8:dformat=word
rlghncxa03w 01-03-22 21:13:50 EST Rel 28.1.0
SDS Memory Dump from IMT Address H'000a
Source-Address = H'00103abc Length = 8 bytes
0000 ffff 00ff 00ff 0000 ........
;
disp-mem:card=psm-a:addr=h'03a-h’001:bc=8
rlghncxa03w 01-03-22 21:13:50 EST Rel 28.1.0
SDS Memory Dump from IMT Address H'00f6
Source-Address = H'003a0001 Length = 8 bytes
0000 04 0d 3d 1c 04 0d 3d 1c ..=...=.
;
Related Topics
disp-trace
Use this command to display trace entries.
Example
disp-trace
disp-trace:traceid=5
Dependencies
A valid value must be specified for the traceid parameter.
None
Output
disp-trace
stdcfg2b 07-10-05 12:55:32 EST EAGLE 37.5.0
Trace Request 1:
CARD= SS7ANSI OPC= 001-001-001
TRACE DISPLAY COMPLETE.
;
dlt-bp
Use this command to delete breakpoints in the communication or application processors.
Parameters
- card (optional)
- The card location in the form of GPLID–Subsystem ID.
- Range:
- GPLID-Substystem ID
GPLID— atmhc, deirhc, erthc, glshc, hipr2, ipghc, iplhc, ipsg, ipshc, mcphc, oamhc, pktgen, sccphc, siphc, slanhc, ss7hc, utility
Subsystem ID— a, b, act, stb, all
The OAMHC GPL can be specified with any of the subsystem IDs. For all other GPLs, only the all subsystem ID is valid.
- loc (optional)
- The card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115
Example
dlt-bp:loc=1209:ueng=2
dlt-bp:card=hipr2-all
dlt-bp:loc=6312
Dependencies
The loc, imt, or card parameter must be specified.
Only one of the loc, imt, and card parameters can be specified in the command.
The ueng parameter can be specified only for IXP-based cards.
The card location specified by the loc parameter must be in the database.
Values of 1114, 1116, 1117, and 1118 cannot be specified for the loc parameter.
All of the subsystem values can be specified with the oamhc GPLID. The other GPLID values can be specified only with the all subsystem value.
The addr and paddr parameters cannot be specified together in the command.
Notes
The imt parameter allows this command to be entered for a card that has not been configured in the system.
Output
dlt-bp:card=oam-all:proc=com
Command Accepted - Processing
tekelecstp 97-01-20 19:21:10 EST Rel 37.0.0
dlt-bp:card=oam-all:proc=com
Command entered at terminal #1.
;
dlt-ee-flt
Use this command to delete an Eagle Eyes Filter from the Eagle Eyes Filter (EE FLT) table. The EE FLT entry consists of a Filter ID and Filter specific data. It can be used to delete a filter only when it is not associated with any card.
Example
dlt-ee-flt:fltid=20
Dependencies
The specified Filter ID must exist in the EE FLT table.
The Eagle Eyes Filter table must be available.
The specified filter should not be associated with any network card.
Notes
None.
Output
dlt-ee-flt:fltid=3
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
EE FLT table is (2 of 200) 1% full
DLT-EE-FLT: MASP A - COMPLTD
;
Related Topics
dlt-trace
Use this command to delete provisioned MSU tracing criteria from the database.
Example
dlt-trace:traceid=5
dlt-trace
Dependencies
Only values between 1 and 10 are valid for the traceid parameter.
None
Output
dlt-trace:traceid=1
stdcfg2b 07-10-05 13:03:29 EST EAGLE 37.5.0
dlt-trace:traceid=1
Command entered at terminal #4.
;
Related Topics
ent-bp
Use this command to add breakpoints in communications and application processors in the system.
Parameters
- access (optional)
- The access type, in the form of access type-format.
Use the data parameter to set the format on IXP-based cards.
- bc (optional)
-
The number of data bytes to display.
For IXP-based cards, bc represents the number of bytes of memory. The number of bytes of stack to be displayed is 255 – bc. For example, if bc=128, then 128 bytes of memory and 127 bytes of stack are displayed. If bc=0, then 0 bytes of memory and 255 bytes of stack are displayed. The exception to this rule is that 1 byte of stack is never displayed.
- ca (optional)
-
Condition “a” in the form of register–condition–integer.
The value register is the CPU internal register.
The value condition is the comparison condition (equal, not equal, greater than, less than, greater than or equal, less than or equal).
The value integer is the value for comparison.
- card (optional)
- The card location, in the form of GPLID–Subsystem ID.
- Range:
- GPLID-Subsystem ID
GPLID—atmhc, deirhc, erthc, glshc, hipr2, ipghc, iplhc, ipsg, ipshc, mcphc, oamhc, pktgen, sccphc, siphc, slanhc, ss7hc, utility
Subsystem ID— a, b, act, stb, all
The OAMHC GPL can be specified with any of the subsystem IDs.
For all other GPLs, only the all subsystem ID is valid.
- cb (optional)
-
Condition b in the form of register–condition–integer.
The value register is the CPU internal register.
The value condition is the comparison condition (equal, not equal, greater than, less than, greater than or equal, less than or equal).
The value integer is the value for comparison.
- data (optional)
- This parameter instructs a data breakpoint to qualify on a match of the data.
Note:
This parameter is valid only on IXP-based cards.
- dr (optional)
-
The data register indirect memory dump, in the form register-register-integer.
The register-register value is the CPU internal register.
The integer value is the offset value.
- Range:
- register-register-integer
register—sp, bp, ss, ds, es, cs, fl, ax, ah, al, bx, bh, bl, cx, ch, cl, dx, dh, dl, di, si, ip, fs, gs, esi, edi, ebp, esp, eip, efl, eax, ebx, ecx, edx
register—sp, bp, ds, ss, es, cs, fl, ax, ah, al, bx, bh, bl, cx, ch, cl, dx, dh, dl, di, si, ip, fs, gs, esi, edi, ebp, esp, eip, efl, eax, ebx, ecx, edx
integer— h’00–h’ffffffff
- loc (optional)
- The card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115
Example
ent-bp:loc=1204:paddr=h’27c3c:type=p486-data:access=rw-word
ent-bp:loc=1109:paddr=h’401000:type=arm-codesw:access=rw-any:ca=r7-eq-0
ent-bp:loc=1209:paddr=h’402000:type=arm-data:access=w-any:data=h’1111-h’ff
ent-bp:loc=1309:paddr=h’403000:type=ixp-codesw:ueng=2:ctx=1
ent-bp:card=hipr2-all:paddr=h’404000:type=arm-codehw:drarm=r3-0:bc=64
ent-bp:loc=1113:addr=h'03a-0001
Dependencies
All of the subsystem values can be specified with the OAMHC GPLID. The other GPLID values can be specified only with the all subsystem value.
Values of 1114, 1116, 1117, and 1118 cannot be specified for the loc parameter.
The loc, imt, or card parameter must be specified.
Only one of the loc, imt, and card parameters can be specified in the command.
The dr parameter and the da parameter cannot be specified together in the command.
The dur=perm parameter and the rep parameter cannot be specified together in the command.
The dur=perm parameter cannot be specified when the value of the processor type portion of the type parameter is p186 or p286.
When the da, dr, or drarm parameter is specified, the dpaddr parameter cannot be specified.
For the type parameter (which is in the form of processor type-breakpoint type), a breakpoint type of data cannot be specified in combination with a processor type of P186, P286, or IXP.
When the paddr parameter and the bc parameter are specified, either the dpaddr or dr parameter must be specified in the command.
The access parameter can be specified only when the type parameter value is p486-data or arm-data.
The bc parameter value cannot be greater than 96 for x86-based cards.
The ind parameter value cannot be greater than 3.
The specified card must be in use.
For 80286 processors, registers for 80386 processors cannot be specified.
For 80286 processors, integer values for registers and conditions must be less than 65535.
The ueng parameter is valid only on IXP-based cards (the value ixp is specified for the processor type portion of the type parameter).
The cts parameter is valid only on IXP-based cards (the value ixp is specified for the processor type portion of the type parameter).
The data parameter is valid only on IXP-based cards.
The data parameter is valid only when the value is data for the breakpoint type portion of the type parameter.
The register values sp, lr, pc, and r0-r15 for the ca or cb parameters are valid only on IXP-based (ARM processor) cards.
The ca and cb parameters cannot be specified when the value ixp is specified for the processor type portion of the type parameter.
The drarm parameter can be specified only on IXP-based cards.
The drarm parameter can be specified only when the value arm is specified for the processor type portion of the type parameter.
The dr parameter cannot be specified for IXP-based cards.
The data and codesw values for the breakpoint type portion of the type parameter cannot be specified when the value ixp is specified for the processor type portion of the type parameter.
The arm and ixp values for the processor type portion of the type parameter are valid only on IXP-based cards.
The value any for the format portion of the access parameter can be specified only on IXP-based cards. The format value must be set to any on IXP-based cards.
When the value ixp is specified for the processor type portion of the type parameter, the ueng and cts parameters must be specified.
The addr parameter can be specified only when the proc=com parameter is specified for DS0 cards with PROM-based COM processors (such as TSMs).
When the ca, cb, and dr parameters are used with 80186 and 80286 processors, the register values ip, fs, gs, esi, edi, ebp, esp, eip, efl, eax, ebx, ecx, and edx cannot be specified. These registers can be used only with 80486 processors. The integer values for these parameters when used with 80186 and 80286 processors must be less than h’ffff (65535).
The data value for the breakpoint type portion of the type parameter cannot be specified with the values p186, p286, and ixp for the processor type portion of the type parameter.
The da parameter cannot be specified for IXP-based cards.
An ARM register value must be specified for an IXP-based card with an ARM processor.
The addr or paddr parameter must be specified in the command. Both parameters cannot be specified in the command.
Notes
The imt parameter allows this command to be entered for a card that has not been configured in the system.
Output
ent-bp:loc=1113:addr=h'03a-0001
rlghncxa03w 04-08-22 21:14:41 EST EAGLE 33.0.0
SDS Response Code 22 from IMT Address H'00f6 - command complete.
rlghncxa03w 04-08-22 21:14:41 EST EAGLE 33.0.0
SDS Response from IMT Address H'000a - command complete.
;
ent-bp:loc=6205:paddr=h'03a002
rlghncxa03w 12-05-22 21:14:41 EST EAGLE 45.0.0
SDS Response Code 22 from IMT Address H'00fd - command complete.
;
ent-ee-flt
Use this command to enter Eagle Eyes Filter data in the Eagle Eyes Filter (EE FLT) table. The EE FLT entry consists of a Filter ID and Filter specific data. After the FLT ID is provisioned, it can be used in the dlt-ee-flt and chg-ee-card commands.
Parameters
Example
ent-ee-flt:appl=ip:type=inc:ipprot=sctp:ssport=2048:stype=data:sctpstr=100
ent-ee-flt:appl=atm:type=exl:port=a:sscopsu=data:mtp3si=sccp
ent-ee-flt:appl=e1t1:type=exl:port=a1:sutype=msu:mtp3si=tup
Dependencies
If the appl=ip then ipprot, ipsrc or ipdst parameters must be specified.
If the ssport, sdport or stype parameters are specified, then the ipprot=sctp parameter must be specified.
At least one optional parameter (ipprot or port) must be specified.
If the sctppld parameter is specified, then the stype=data and ipprot=sctp parameters must be specified.
If the sctpstr parameter is specified, then the stype=data and ipprot=sctp parameters must be specified.
The Eagle Eyes Filter table cannot contain more than 200 entries.
The Eagle Eyes Filter table must be available.
If the appl=ip parameter is specified, then the appl=atm and appl=e1t1 parameters must not be specified.
If the appl=atm parameter is specified, then the appl=ip and appl=e1t1 parameters must not be specified.
If the appl=e1t1 parameter is specified, then the appl=atm and appl=ip parameters must not be specified.
If the appl=atm parameter is specified, then the port parameter can only be either a, b or a1.
Notes
- ipprot, ipsrc, ipdst, ssport, sdport, style, sctppld, sctpstr
- sscopsu, mtp3si, port
- sutype, mtp3si, port
Output
ent-ee-flt:appl=atm:type=inc:port=a:sscopsu=data
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
EE FLT table is (1 of 200) 1% full
ENT-EE-FLT: MASP A - COMPLTD
;
ent-trace
Use this debug command to trace MSUs sent to Service Module cards or to LIM cards running the SS7ANSI, CCS7ITU, VSCCP, ATMITU, ATMANSI, IPLIMI, SS7IPGW, IPGWI, or IPSG applications.
The EAGLE traps MSUs that meet the provisioned tracing criteria, and the MSU remains in the trapped state for the life span of that MSU. The life span varies depending on the type of MSU. For MTP-Routed or GTT MSUs, the life span lasts until the MSU travels out of the EAGLE or is discarded. For LNP MSUs, the life span lasts until the request is processed. The response is not part of the LNP MSU. Trapping a response requires the provisioning of another MSU trace.
This command uses different parameters depending on the card type sending the MSU as shown:
- Service Module— error, gt, lrn, tn, ssp/sspa/sspi/sspn/sspn24/sspn16, dn, entityid, imei, and imsi
- LIM card running ANSI applications— error, ssp/sspa, opc/opca, dpc/dpca, tlnpisuptype, and gt
- LIM card running ITU applications— error, sspi/sspn/sspn24/sspn16, opci/opcn/opcn24/opcn16, dpci/dpcn/dpcn24/dpcn16, and gt
The lrn, tn, dn, entityid, imsi, imei, and error parameters are mutually exclusive.
The following parameters can be used once in a single MSU trace request with ONE of the mutually exclusive parameters specified above: opc, dpc, ilsn, si, gt, ssp, h0h1, cpc, or cic/ecic.
The cic/ecic parameters can be used only for ISUP traffic. The ecic parameter must be specified with the cic parameter.
For all cards supported by this command, the error parameter can be provisioned as the only optional parameter or in addition to any other optional parameter to trace any messages that fail verification or processing. If the error parameter not specified, the default value is error=no.
Caution:
If the system configuration approaches the maximum number of provisioned Service Module cards, then entering this command might cause an OAM to reset because of the amount of information that may be returned.Parameters
- brief (optional)
- This parameter specifies whether all information is provided for each MSU as it moves through the EAGLE.
- cpc (optional)
- ANSI destination point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm).
- Synonym:
- cpca
- Range:
- 000-255
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
When
chg-sid:pctype=ansiis specified, ni = 000 is not valid.When
chg-sid:pctype=ansiis specified, nc = 000 is not valid if ni = 001–005.When
chg-sid:pctype=ansiis specified, nc = 000 is valid if ni = 006–255.The point code 000-000-000 is not a valid point code.
- cpci (optional)
- ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).
- cpcn (optional)
- ITU national destination point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the
chg-stpopts:npcfmtiflexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnngc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnngc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- cpcn24 (optional)
- 24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).
- cpcn16 (optional)
- 16-bit ITU national point code with subfields unit number-sub number area-main number area (un-sna-mna).
- dn (optional)
- Directory Number. This parameter is used for the ANSI41 AIQ, ATINP, G-Flex, G-Port, INP, PPSMS, or V-Flex features.
The tn parameter is used as the directory number for LNP.
- dpc (optional)
- ANSI destination point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm)
- Synonym:
- dpca
- Range:
- 000-255
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
When
chg-sid:pctype=ansiis specified, ni = 000 is not valid.When
chg-sid:pctype=ansiis specified, nc = 000 is not valid if ni = 001–005.When
chg-sid:pctype=ansiis specified, nc = 000 is valid if ni = 006–255.The point code 000-000-000 is not a valid point code.
- dpci (optional)
- ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).
- dpcn (optional)
- ITU national destination point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the
chg-stpopts:npcfmtiflexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnn-gc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnn-gc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- dpcn24 (optional)
- 24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).
- dpcn16 (optional)
- 16-bit ITU national point code with subfields unit number-sub number area-main number area (un-sna-mna).
- error (optional)
- This parameter specifies whether to perform a trace on any message verification error and message processing error
- h0h1 (optional)
- A combination of values contained in some MSUs. The h0 value is the code for a message group, and the h1 value is the code for a message within that group.
- loc (optional)
- The card location of the card as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
- opc (optional)
- ANSI point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm). The prefix subfield indicates a private point code (prefix-ni-nc-ncm).
- Range:
- 000-255
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
When
chg-sid:pctype=ansiis specified, ni = 000 is not valid.When
chg-sid:pctype=ansiis specified, nc = 000 is not valid if ni = 001–005.When
chg-sid:pctype=ansiis specified, nc = 000 is valid if ni = 006–255.The point code 000-000-000 is not a valid point code.
- opci (optional)
- ITU international origination point code with subfields zone-area-id. The prefix subfield indicates a spare point code, private point code, or private and spare point code (prefix-zone-area-id).
- opcn (optional)
- ITU national destination point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the
chg-stpopts:npcfmtiflexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnngc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnngc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- opcn24 (optional)
- 24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).
- opcn16 (optional)
- 16-bit ITU national point code with subfields unit number-sub number area-main number area (un-sna-mna).
- ssp (optional)
- ANSI destination point code with subfields network indicator-network cluster-network cluster member (ni-nc-ncm).
- Range:
- 000-255
Specify a valid value for each subfield of the point code, and separate the subfields with a dash (-).
When
chg-sid:pctype=ansiis specified, ni = 000 is not valid.When
chg-sid:pctype=ansiis specified, nc = 000 is not valid if ni = 001–005.When
chg-sid:pctype=ansiis specified, nc = 000 is valid if ni = 006–255.The point code 000-000-000 is not a valid point code.
- sspi (optional)
- ITU international destination point code with subfields zone-area-id. The prefix subfield indicates a spare point code (prefix-zone-area-id).
- sspn (optional)
- ITU national destination point code in the format of a 5-digit number (nnnnn); or 2, 3, or 4 numbers (members) separated by dashes (m1-m2-m3-m4) as defined by the
chg-stpopts:npcfmtiflexible point code option. A group code must be specified when the ITUDUPPC feature is turned on (nnnnngc, m1-m2-m3-m4-gc). The prefix subfield indicates a spare point code (prefix-nnnnn, prefix-nnnnngc, prefix-m1-m2-m3-m4, prefix-m1-m2-m3-m4-gc).
- sspn24 (optional)
- 24-bit ITU national destination point code with subfields main signaling area-sub signaling area-signaling point (msa-ssa-sp).
Example
ent-trace:opc=1-1-1:card=SS7ANSI-ALL:rep=2
ent-trace:tlnpisuptype=01:card=SS7ANSI-ALL
ent-trace:dn=12345:card=VSCCP-ALL
ent-trace:imsi=c122d:card=VSCCP-ALL
ent-trace:card=ccs7itu-all:dpc=2-7-5:error=no
ent-trace:card=vsccp-all:error=yes
ent-trace:card=ccs7itu-all:sspn24=10-11-12:opcn24=10-10-10:dpcn24=10-101-11
ent-trace:imei=123456789101234:card=VSCCP-ALL
ent-trace:entityid=c123:card=VSCCP-ALL
ent-trace:loc=1305:si=5:brief=yes
ent-trace:dn=98912345:loc=1105
ent-trace:card=ccs7itu-all:sspn16=121-10-12:opcn16=121-10-13:dpcn16=121-10-14
Dependencies
The card parameter or the loc parameter must be specified.
At least one optional parameter must be specified. The error parameter can be specified as the only optional parameter or with any of the other optional parameters in the command.
The gt, entityid, dn, imei, and imsi parameters cannot have a value of none.
A valid value must be specified for the card parameter.
The only qualifier allowed for the card parameter is all.
The gt, entityid, dn, imei, imsi, lrn, and tn parameters are invalid for LIM cards running the SS7ANSI, ATMANSI, or SS7IPGW applications.
The opci/opcn/opcn24/opcn16, dpci/dpcn/dpcn24/dpcn16, and sspi/sspn/sspn24/sspn16 ITU point code parameters are invalid for LIM cards running the SS7ANSI, ATMANSI, or SS7IPGW applications.
The gt, entityid, dn, imei, imsi, lrn, tn, and tlnpisuptype parameters are invalid for LIM cards running the ATMITU or IPLIMI applications.
The opc/opca, dpc/dpca, and ssp/sspa ANSI point code parameters are invalid for LIM cards running the IPLIMI application.
The opc, dpc, and tlnpisuptype parameters cannot be specified for Service Module cards.
The G-Flex feature or the Equipment Identity Register feature must be turned on before the imsi parameter can be specified.
If the ITUDUPPC feature is turned on, the ITU national point code must be specified as a full point code.
The EIR feature must be turned on before the imei parameter can be specified.
The AINPQ, G-Flex, G-Port, IDP Relay, INP, PPSMS, or V-Flex feature must be turned on or the ANSI41 AIQ or ATINP feature must be enabled before the dn parameter can be specified.
The G-Flex, G-Port, INP, or V-Flex feature must be turned on or the ATINP, IDP Relay or any TIF feature must be enabled before the entityid parameter can be specified.
The loc and card parameters are mutually exclusive.
Only one of the lrn, tn, dn, entityid, imsi, imei, or error parameters can be specified in a single MSU trace request.
A maximum of 10 traces can be entered in the system at a time.
Values 1113 - 1118 cannot be specified for the loc parameter.
The J7 Support feature must be enabled before the sspn16/opcn16/dpcn16 parameters can be specified.
Output
This example shows the output for an MTP trace:
ent-trace:loc=1101:dpc=7-1-0
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e1: Card=1101 RX - Link B0
Trace Condition:
LOC= 1101
DPC= 007-001-000
MSU info:
TOTAL MSU SIZE= 12 Bytes
MSU DATA SIZE = 4 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 85 00 01 07 01 65 01 16
DATA: 00 00 09 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e1: Card=1101 Use RTE: 007-001-000:H'0001
Trace Condition:
LOC= 1101
DPC= 007-001-000
MSU info:
TOTAL MSU SIZE= 12 Bytes
MSU DATA SIZE = 4 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 85 00 01 07 01 65 01 16
DATA: 00 00 09 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e1: Card=1101 Sending to 1103:B1
Trace Condition:
LOC= 1101
DPC= 007-001-000
MSU info:
TOTAL MSU SIZE= 12 Bytes
MSU DATA SIZE = 4 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 85 00 01 07 01 65 01 0b
DATA: 00 00 09 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e1: Card=1103 MSU Received from 1101
Trace Condition:
LOC= 1101
DPC= 007-001-000
MSU info:
TOTAL MSU SIZE= 12 Bytes
MSU DATA SIZE = 4 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 85 00 01 07 01 65 01 0b
DATA: 00 00 09 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e1: Card=1103 MSU sent to L2 - B1
Trace Condition:
LOC= 1101
DPC= 007-001-000
MSU info:
TOTAL MSU SIZE= 12 Bytes
MSU DATA SIZE = 4 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 85 00 01 07 01 65 01 0b
DATA: 00 00 09 00
TRACE OUTPUT COMPLETE.
;
This example shows the output for an SCCP trace:
ent-trace:loc=1101:gt=9194605500
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1101 RX - Link B0
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 90 Bytes
MSU DATA SIZE = 82 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 01 01 65 01 02
SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1101 TVG: Sending to SCCP 1107
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 90 Bytes
MSU DATA SIZE = 82 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 01 01 65 01 02
SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1107 MSU Received from 1101
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 90 Bytes
MSU DATA SIZE = 82 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 01 01 65 01 02
SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1107 SCCP: Before SS7 Trans Encod
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 97 Bytes
MSU DATA SIZE = 89 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 01 01 65 01 02
SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
08 01 65 01 00 04
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1107 SCCP: After SS7 Trans Encode
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 97 Bytes
MSU DATA SIZE = 89 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 07 00 01 01 02
SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
08 01 65 01 00 04
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1107 Use RTE 007-001-000:H'0009
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 97 Bytes
MSU DATA SIZE = 89 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 07 00 01 01 02
SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
08 01 65 01 00 04
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1107 Sending to 1103:B1
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 97 Bytes
MSU DATA SIZE = 89 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 07 00 01 01 01
SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
08 01 65 01 00 04
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'0000: Card=1103 MSU Received from 1107
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 97 Bytes
MSU DATA SIZE = 89 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 07 00 01 01 01
SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
08 01 65 01 00 04
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'0000: Card=1103 MSU sent to L2 - B1
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 90 Bytes
MSU DATA SIZE = 82 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 07 00 01 01 01
SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
TRACE OUTPUT COMPLETE.
;
This example shows the output for a trace when truncated output is requested. Only the filters that are specified in the command are displayed.
ent-trace:loc=1305:si=0:hoh1=20:sls=255:cpc=001-002-003:mode=debug:brief=yes
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
;
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
MSU TRACE H'0081: Card=1305
Trace ID 1 Condition:
LOC= 1305
SI= 0
H0H1= 20
SLS= 255
CPC= 001-002-003
MODE= DEBUG
Info: RX - Link A0
TRACE OUTPUT COMPLETE.
;
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
MSU TRACE H'0081: Card=1305
Trace ID 1 Condition:
LOC= 1305
SI= 0
H0H1= 20
SLS= 255
CPC= 001-002-003
MODE= DEBUG
Info: TIF Stop Action: OK
TRACE OUTPUT COMPLETE.
;
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
MSU TRACE H'0081: Card=1305
Trace ID 1 Condition:
LOC= 1305
SI= 0
H0H1= 20
SLS= 255
CPC= 001-002-003
MODE= DEBUG
Info: TVG: Sending to SCCP 1317
TRACE OUTPUT COMPLETE.
;
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
MSU TRACE H'0081: Card=1317
Trace ID 1 Condition:
LOC= 1305
SI= 0
H0H1= 20
SLS= 255
CPC= 001-002-003
MODE= DEBUG
Info: SCCP: MSU RX from 1305
TRACE OUTPUT COMPLETE.
;
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
MSU TRACE H'0081: Card=1317
Trace ID 1 Condition:
LOC= 1305
SI= 0
H0H1= 20
SLS= 255
CPC= 001-002-003
MODE= DEBUG
Info: TIF Process Msg: Ruleset TIF1
TRACE OUTPUT COMPLETE.
;
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
MSU TRACE H'0081: Card=1317
Trace ID 1 Condition:
LOC= 1305
SI= 0
H0H1= 20
SLS= 255
CPC= 001-002-003
MODE= DEBUG
Info: TIF: No Error CdPN:1111111119703819111100
TRACE OUTPUT COMPLETE.
;
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
MSU TRACE H'0081: Card=1305
Trace ID 1 Condition:
LOC= 1305
SI= 0
H0H1= 20
SLS= 255
CPC= 001-002-003
MODE= DEBUG
Info: Use RTE (16) DPCa: 023-172-011, OPCa: 013-159-005
TRACE OUTPUT COMPLETE.
;
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
MSU TRACE H'0081: Card=1305
Trace ID 1 Condition:
LOC= 1305
SI= 0
H0H1= 20
SLS= 255
CPC= 001-002-003
MODE= DEBUG
Info: Sending to 2311:B3
TRACE OUTPUT COMPLETE.
;
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
MSU TRACE H'0081: Card=2311
Trace ID 1 Condition:
LOC= 1305
SI= 0
H0H1= 20
SLS= 255
CPC= 001-002-003
MODE= DEBUG
Info: MSU Received from 1305
TRACE OUTPUT COMPLETE.
;
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
MSU TRACE H'0081: Card=2311
Trace ID 1 Condition:
LOC= 1305
SI= 0
H0H1= 20
SLS= 255
CPC= 001-002-003
MODE= DEBUG
Info: MSU sent to L2 - B3: DPCa= 023-172-011, OPCa= 013-159-005
TRACE OUTPUT COMPLETE.
;
tklc1071501 08-09-22 10:49:00 EST EAGLE5 39.2.0
MSU TRACE H'0081: Card=2311
Trace ID 1 Condition:
LOC= 1305
SI= 0
H0H1= 20
SLS= 255
CPC= 001-002-003
MODE= DEBUG
Info: Transmitted and ACK'd on B3
TRACE OUTPUT COMPLETE.
;
ent-trace:loc=1101:dpcn16=7-1-0
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e1: Card=1101 RX - Link B0
Trace Condition:
LOC= 1101
DPC= 007-001-000
MSU info:
TOTAL MSU SIZE= 12 Bytes
MSU DATA SIZE = 4 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 85 00 01 07 01 65 01 16
DATA: 00 00 09 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e1: Card=1101 Use RTE: 007-001-000:H'0001
Trace Condition:
LOC= 1101
DPC= 007-001-000
MSU info:
TOTAL MSU SIZE= 12 Bytes
MSU DATA SIZE = 4 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 85 00 01 07 01 65 01 16
DATA: 00 00 09 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e1: Card=1101 Sending to 1103:B1
Trace Condition:
LOC= 1101
DPC= 007-001-000
MSU info:
TOTAL MSU SIZE= 12 Bytes
MSU DATA SIZE = 4 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 85 00 01 07 01 65 01 0b
DATA: 00 00 09 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e1: Card=1103 MSU Received from 1101
Trace Condition:
LOC= 1101
DPC= 007-001-000
MSU info:
TOTAL MSU SIZE= 12 Bytes
MSU DATA SIZE = 4 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 85 00 01 07 01 65 01 0b
DATA: 00 00 09 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e1: Card=1103 MSU sent to L2 - B1
Trace Condition:
LOC= 1101
DPC= 007-001-000
MSU info:
TOTAL MSU SIZE= 12 Bytes
MSU DATA SIZE = 4 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 85 00 01 07 01 65 01 0b
DATA: 00 00 09 00
TRACE OUTPUT COMPLETE.
;
This example shows the output for an SCCP trace:
ent-trace:loc=1101:gt=9194605500
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1101 RX - Link B0
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 90 Bytes
MSU DATA SIZE = 82 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 01 01 65 01 02
SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1101 TVG: Sending to SCCP 1107
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 90 Bytes
MSU DATA SIZE = 82 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 01 01 65 01 02
SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1107 MSU Received from 1101
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 90 Bytes
MSU DATA SIZE = 82 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 01 01 65 01 02
SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1107 SCCP: Before SS7 Trans Encod
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 97 Bytes
MSU DATA SIZE = 89 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 01 01 65 01 02
SCCP: 09 80 03 0e 13 0b 8b 8c 28 04 01 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
08 01 65 01 00 04
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1107 SCCP: After SS7 Trans Encode
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 97 Bytes
MSU DATA SIZE = 89 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 07 00 01 01 02
SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
08 01 65 01 00 04
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1107 Use RTE 007-001-000:H'0009
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 97 Bytes
MSU DATA SIZE = 89 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 07 00 01 01 02
SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
08 01 65 01 00 04
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'00e2: Card=1107 Sending to 1103:B1
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 97 Bytes
MSU DATA SIZE = 89 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 07 00 01 01 01
SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
08 01 65 01 00 04
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'0000: Card=1103 MSU Received from 1107
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 97 Bytes
MSU DATA SIZE = 89 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 07 00 01 01 01
SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00 02
08 01 65 01 00 04
TRACE OUTPUT COMPLETE.
;
stdcfg1b 07-08-10 15:51:33 EST EAGLE 37.5.0
MSU TRACE H'0000: Card=1103 MSU sent to L2 - B1
Trace Condition:
LOC= 1101
GT= 9194605500
MSU info:
TOTAL MSU SIZE= 90 Bytes
MSU DATA SIZE = 82 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 83 00 01 07 00 01 01 01
SCCP: 09 80 03 0e 13 0b cb 10 00 01 07 0a 19 49 06 55 00 05 c3 0a
04 05 06
TCAP: 3a e2 38 c7 04 e5 04 61 80 e8 30 e9 2e cf 01 00 d0 02 83 01
f2 25 aa 0b 84 09 01 00 11 0a 19 49 06 12 19 84 09 02 00 11
0a 19 39 88 41 63 84 07 07 00 01 03 21 03 00 df 45 01 00
TRACE OUTPUT COMPLETE.
;
This example shows the output to display the selected highest priority component in a TCAP message:
ent-trace:loc=1103:si=3:mode=debug
tekelecstp 17-03-22 11:30:07 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: SCCP: service selector not found
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 3f 78 0c 0c
SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:07 MST EAGLE 46.5.0.0.0-70.26.0
1660.0309 SYSTEM Node is no longer isolated
;
tekelecstp 17-03-22 11:30:07 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: TOBR:Msg=Begin Opcode=2,22,8 ACN(hex)= 0
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 3f 78 0c 0c
SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:08 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: GTT Mode=FD-FG,GTIi=2/2,TT11/242,SS10/242,NP-/-,NAI-/-,SelID=NONE
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 3f 78 0c 0c
SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:08 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: LS: ls661
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 3f 78 0c 0c
SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:09 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: dGT=22222210,gGT=9876543210,gPC=7-080-1,
OPCi=6-006-1,DPCi=7-007-7
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 3f 78 0c 0c
SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:10 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: Opcode 8 from component#3 selected for translation
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 3f 78 0c 0c
SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:10 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: Opcode 2 from component#1 selected for translation
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 3f 78 0c 0c
SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:11 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: SET=FD-cd1-amituopcd-cg1-ZITUOPCD
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 3f 78 0c 0c
SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:11 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: xlatPCi=6-008-1,SS=0,RI=0,GTMODID=-,CGPCACT=DFLT,ACTSN=-
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 3f 78 0c 0c
SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:12 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: SCCP - Before Encode :old, GTT perfd
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 3f 78 0c 0c
SCCP: 09 80 03 0c 16 09 0b 31 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:12 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: After Encd:OPCi=7-007-7,DPCi:6-008-1,CgPC=7-080-1
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 41 f0 0f 0e
SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:13 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: route_message_hp:DPCi=6-008-1,OPC=7-007-7>route_msg_on_rtidx
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 41 f0 0f 0e
SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:13 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: Use RTE (5) DPCi: 6-008-1, OPCi: 7-007-7
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 41 f0 0f 0e
SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:14 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: Rotated SLS = H'0000
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 41 f0 0f 0e
SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:14 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1103
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: Sending to 1102:A1
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 41 f0 0f 0e
SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:15 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1102
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: MSU Received from 1103
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 41 f0 0f 0e
SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-22 11:30:15 MST EAGLE 46.5.0.0.0-70.26.0
MSU TRACE H'0021: Card=1102
Trace ID 1 Condition: (brief=Y, MSU size=145)
LOC= 1103
SI= 3
MODE= debug
Info: MSU sent to L2: A1: DPCi=6-008-1,OPCi=7-007-7,NI=0
MSU info:
TOTAL MSU SIZE= 145 Bytes
MSU DATA SIZE = 140 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 03 41 f0 0f 0e
SCCP: 09 80 03 0c 16 09 0b 41 30 0a 0b 22 22 22 01 0a 4b 81 3a f2
f2 89 67 45 23 01
TCAP: 71 62 6f 48 01 00 6b 1f 28 1d 06 07 00 11 86 05 01 01 01 a0
12 60 10 80 01 00 a1 03 06 01 00 be 06 28 04 a0 02 00 00 6c
49 a1 24 02 01 00 02 01 02 30 1c 04 05 79 58 45 28 93 80 0b
80 00 00 00 00 00 00 00 00 00 00 04 06 91 22 33 44 55 66 a1
10 02 01 00 02 01 16 30 08 80 06 91 21 43 65 87 09 a1 0f 02
01 00 02 01 08 30 07 80 05 89 67 45 23 01
TRACE OUTPUT COMPLETE.
;
This example shows the output for mode=debug:
ent-trace:loc=1107:si=12:mode=debug
tekelecstp 17-03-03 10:23:27 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: RX:SLK A0,DPCi=1-001-3,APCi=1-001-2,TSPCi=1-001-1,SAPC =
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 c2
DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:27 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: SS7_HMDC:4thisPC=N,TRUE_PCi=1-001-3 =>sccp=No
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 c2
DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:27 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: HMDC MTP-routes MSU: call route_message_hp
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 c2
DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:28 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: route_message_hp:DPCi=1-001-3,OPC=1-001-1>route_msg_on_rtidx
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 c2
DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:28 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: Use RTE (5) DPCi: 1-001-3, OPCi: 1-001-1
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 c2
DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:29 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: Rotated SLS = H'000c
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 c2
DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:29 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: Sending to 1108:A0
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 c2
DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:29 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1108
Trace ID 1 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: MSU Received from 1107
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 c2
DATA: 09 08 00 01 6e f9 de 91 b8 81 f6 00 0c 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
This example shows the output for mode=debug and brief=yes:
ent-trace:loc=1107:si=12:mode=debug:brief=yes
tekelecstp 17-03-03 10:23:40 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=Y, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: RX:SLK A0,DPCi=1-001-3,APCi=1-001-2,TSPCi=1-001-1,SAPC =
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:40 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=Y, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: SS7_HMDC:4thisPC=N,TRUE_PCi=1-001-3 =>sccp=No
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:40 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=Y, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: HMDC MTP-routes MSU: call route_message_hp
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:40 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=Y, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: route_message_hp:DPCi=1-001-3,OPC=1-001-1>route_msg_on_rtidx
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:41 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=Y, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: Use RTE (5) DPCi: 1-001-3, OPCi: 1-001-1
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:41 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=Y, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: Rotated SLS = H'0000
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:41 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1107
Trace ID 1 Condition: (brief=Y, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: Sending to 1108:A0
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:41 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c1: Card=1108
Trace ID 1 Condition: (brief=Y, MSU size=101)
LOC= 1107
SI= 12
MODE= debug
Info: MSU Received from 1107
TRACE OUTPUT COMPLETE.
;
This example shows the output for when the mode is not defined:
ent-trace:loc=1107:si=12
tekelecstp 17-03-03 10:23:49 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c2: Card=1107
Trace ID 2 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
Info: RX:SLK A0,DPCi=1-001-3,APCi=1-001-2,TSPCi=1-001-1,SAPC =
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 52
DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:49 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c2: Card=1107
Trace ID 2 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
Info: SS7_HMDC:4thisPC=N,TRUE_PCi=1-001-3 =>sccp=No
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 52
DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:50 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c2: Card=1107
Trace ID 2 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
Info: Use RTE (5) DPCi: 1-001-3, OPCi: 1-001-1
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 52
DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:51 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c2: Card=1107
Trace ID 2 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
Info: Sending to 1107:A0
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 52
DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:51 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c2: Card=1107
Trace ID 2 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
Info: MSU Received from 1107
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 52
DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
tekelecstp 17-03-03 10:23:51 EST EAGLE 46.5.0.0.0-70.21.0
MSU TRACE H'00c2: Card=1107
Trace ID 2 Condition: (brief=N, MSU size=101)
LOC= 1107
SI= 12
Info: MSU sent to L2: A0: DPCi=1-001-3,OPCi=1-001-1,NI=0
MSU info:
TOTAL MSU SIZE= 101 Bytes
MSU DATA SIZE = 096 Bytes
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
MTP: 0c 0b 48 02 52
DATA: 09 08 00 01 81 97 2f 93 bd 83 f6 00 05 00 00 0e 00 10 00 12
00 14 00 16 00 18 00 1a 00 1c 00 1e 00 20 00 22 00 24 00 26
00 28 00 2a 00 2c 00 2e 00 30 00 32 00 34 00 36 00 38 00 3a
00 3c 00 3e 00 40 00 42 00 44 00 46 00 48 00 4a 00 4c 00 4e
00 50 00 52 00 54 00 56 00 58 00 5a 00 5c 00 5e
TRACE OUTPUT COMPLETE.
;
rept-stat-ee
Use this command to generate the status report of Eagle Eyes on network cards.
Parameters
- loc (optional)
- Eagle Eyes Card location.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
Example
rept-stat-ee
rept-stat-ee:loc=1102
Dependencies
The card location specified in the 'loc' parameter must be configured to use Eagle Eyes.
The shelf and card must be equipped.
The specified card location must not be a reserved card location.
Notes
This command can be canceled using the F9 function key or the canc-cmd command. See canc-cmd for more information
Output
This example generates the Eagle Eyes status report for the specified Network Card.
rept-stat-ee:loc=1101
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
LOC STATE
----------------
1101 ACTIVE
Command Completed.
This example generates the Eagle Eyes status report for all the EE configured Network Cards.
rept-stat-ee
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
LOC STATE
----------------
1101 ACTIVE
1103 INACTIVE
Command Completed.
Related Topics
rept-stat-gedti
Use this command to generate a report of the GEDTI Hub's status.
Parameters
- loc (optional)
- GEDTI Hub Card location.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
Example
rept-stat-gedti
rept-stat-gedti:loc=1111
Dependencies
The value specified for the loc parameter must correspond to the location of an IPSM card which is configured as a GEDTI Hub.
Notes
This command can be canceled using the F9 function key or the canc-cmd command. See canc-cmd for more information.
Output
This example generates the report of all the IPSM cards configured as GEDTI Hubs.
rept-stat-gedti
tekelecstp 08-01-29 10:41:52 EST EAGLE 46.0.0
LOC PORT STATE
-------------------------------------------------------------------------
1101 4567 ACTIVE
SID SOCK FD APPL CARD APPL SUBSYS APPL ID PC STATE APPL STATE
-------------------------------------------------------------------------
0 -1 0 0 0 0 0
1 -1 0 0 0 0 0
2 -1 0 0 0 0 0
3 -1 0 0 0 0 0
4 -1 0 0 0 0 0
5 -1 0 0 0 0 0
6 -1 0 0 0 0 0
7 -1 0 0 0 0 0
LOC PORT STATE
-------------------------------------------------------------------------
1112 4568 INACTIVE
SID SOCK FD APPL CARD APPL SUBSYS APPL ID PC STATE APPL STATE
-------------------------------------------------------------------------
0 0 0 0 0 0 0
Command Completed.
This example generates the report of the specified IPSM card configured as a GEDTI Hub.
rept-stat-gedti:loc=1101
tekelecstp 08-01-29 10:41:54 EST EAGLE 46.0.0
LOC PORT STATE
-------------------------------------------------------------------------
1101 4567 ACTIVE
SID SOCK FD APPL CARD APPL SUBSYS APPL ID PC STATE APPL STATE
-------------------------------------------------------------------------
0 -1 0 0 0 0 0
1 -1 0 0 0 0 0
2 -1 0 0 0 0 0
3 -1 0 0 0 0 0
4 -1 0 0 0 0 0
5 -1 0 0 0 0 0
6 -1 0 0 0 0 0
7 -1 0 0 0 0 0
Command Completed.
Related Topics
rtrv-ee-card
Use this command to display Eagle Eyes Card Configuration data from the Eagle Eyes Card (EE CARD) table. The EE CARD entry consists of a Card Loc and Eagle Eyes Card specific data.
Parameters
- loc (optional)
- Eagle Eyes Card location.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
Example
rtrv-ee-card
rtrv-ee-card:loc=1102
Dependencies
The EE CARD table must be available.
The card location specified in the 'loc' parameter must be configured to use Eagle Eyes.
The Eagle Eyes Filter table must be available.
Notes
None.
Output
This example displays the Eagle Eyes parameters for all the EE configured network cards.
rtrv-ee-card
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
LOC THR SECLIM PKTLIM KBLIM
-----------------------------------
1101 10000 5644800 10000000 4000000
1201 1000 464400 NONE 2000000
EE CARD table is (2 of 254) 1% full
RTRV-EE-CARD: MASP A - COMPLTD
;
This example displays the Eagle Eyes parameters for the specified EE configured network card.
rtrv-ee-card:loc=1201
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
EE OAM Card Configuration
-------------------------------------------
LOC THR SECLIM PKTLIM KBLIM PORT
-------------------------------------------
1201 1000 2000 2000 3000 -
ATM FILTERS
-----------------------------
ID TYPE PORT SSCOPSU MTP3SI
-----------------------------
71 INC a ctrl -
13 INC a - -
5 EXC b - -
EE CARD table is (2 of 254) 1% full
RTRV-EE-CARD: MASP A - COMPLTD
;
Legend
- LOC--- Card location as stenciled on the shelf of the system.
- THR--- The sending rate of the Eagle Eyes throttle task in IMT packets per second.
- SECLIM--- The limit on the amount of time to perform the trace, in seconds.
- PKTLIM--- The limit on the number of Ethernet frames to send.
- KBLIM--- The file size limit of the capture file created, in kilobytes.
- PORT--- Port being filtered.
- ID--- Eagle Eyes Filter ID.
- TYPE--- Eagle Eyes Filter Type.
- SSCOPSU--- SSCOP sub-protocol or SU type filter.
- MTP3SI--- MTP3 user filter.
rtrv-ee-flt
Use this command to retrieve Eagle Eyes Filter data from the Eagle Eyes Filter (EE FLT) table. The EE-FLT entry consists of a Filter ID and Filter specific data. It can be used to obtain the Filter ID of the filter to be associated to a card using the CHG-EE-CARD command.
Parameters
Example
rtrv-ee-flt:appl=ip
rtrv-ee-flt:fltid=16
Dependencies
The Eagle Eyes Filter table must be available.
The specified Filter ID must exist in the EE FLT table.
The Filter ID and APPL are mutually exclusive parameters.
Notes
None.
Output
This example displays the Filter parameters for the specified Filter ID.
rtrv-ee-flt:fltid=85
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
EE OAM Filter Configuration
IP FILTERS
--------------------------------------------------------------------------
ID TYPE IP IP IP SCTP SCTP SCTP SCTP SCTP
PROT SRC DST SRC DST TYPE DATA DATA
ADDR ADDR PORT PORT PLD STR
--------------------------------------------------------------------------
85 INC sctp - - - - data sua -
EE Filter table is (83 of 200) 42% full.
;
Command ExecutedThis example displays the Filter parameters for the ATM Application Type.
rtrv-ee-flt:appl=atm
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
EE OAM Filter Configuration
ATM FILTERS
-----------------------------
ID TYPE PORT SSCOPSU MTP3SI
-----------------------------
5 EXC b - -
13 INC a - -
67 INC a - -
68 INC a1 - -
71 INC a ctrl -
77 INC all - -
EE Filter table is (83 of 200) 42% full.
;
Command Executed
This example displays the Filter parameters for the IP Application Type.
rtrv-ee-flt:appl=ip
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
EE OAM Filter Configuration
IP FILTERS
----------------------------------------------------------------------------------
ID TYPE IP IP IP SCTP SCTP SCTP SCTP SCTP
PROT SRC DST SRC DST TYPE DATA DATA
ADDR ADDR PORT PORT PLD STR
----------------------------------------------------------------------------------
3 INC tcp - - - - - - -
8 EXC - - 3.3.3.3 - - - - -
9 EXC - - 5.5.50.5 - - - - -
18 INC sctp 10.248.13.9 - 1234 - - - -
19 INC sctp 10.248.13.9 - - 1234 - - -
32 INC sctp 10.248.13.9 - 1234 - data m2pa -
34 INC sctp 111.248.131.119 111.111.111.111 1234 2345 data m2pa -
37 EXC sctp 111.248.131.119 111.111.111.111 1234 2345 data m2pa -
38 EXC sctp 111.248.131.119 111.111.111.111 1234 2345 data - -
46 EXC sctp 10.248.13.9 - 1234 - data m2pa -
50 EXC sctp 10.248.13.9 - 1234 - data m2pa -
85 INC sctp - - - - data sua -
EE Filter table is (83 of 200) 42% full.
;
Command Executed
This example displays the Filter parameters for the E1T1 Application Type.
rtrv-ee-flt:appl=e1t1
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
EE OAM Filter Configuration
E1T1 FILTERS
-----------------------------
ID TYPE PORT SUTYPE MTP3SI
-----------------------------
6 INC a21 - -
7 INC a22 - -
12 INC a - -
69 INC a31 - -
70 INC b31 - -
72 INC a lsu -
EE Filter table is (83 of 200) 42% full.
;
Command Executed
This example displays the Filter parameters for all the configured Filters.
rtrv-ee-flt
tekelecstp 10-03-08 14:43:31 EST EAGLE 46.0.0
EE Filter Configuration
IP Filters
ID TYPE IP IP IP SS SD STYPE SCTP SCTP
PROT SRC DST PORT PORT PLD STR
ADDR ADDR
-----------------------------------------------------------------------------------
1 INC SCTP 10.248.13.10 10.25.80.191 65535 10000 DATA M2PA 65535
47 EXC SCTP 101.248.131.191 102.251.118.111 65432 10245 HTBT - -
ATM Filters
ID TYPE PORT SSCOPSU MTP3SI
-----------------------------
100 INC A DATA SCCP
105 EXC B CTRL -
E1T1 Filters
ID TYPE PORT SUTYPE MTP3SI
-----------------------------
2 INC A1 MSU SCCP
EE FLT table is (5 of 200) 2% full
;
Command Executed
rtrv-upgrade-config
Use this command to retrieve provisioned data used by the upgrade software during an upgrade of an in-service EAGLE from a source release to the target release.
Parameters
Example
Display a list of DMS tables that will be converted during the next upgrade.rtrv-upgrade-config:display=tblcnv
rtrv-upgrade-config
Dependencies
None
Output
rtrv-upgrade-config:display=tblcnv
rlghncxa03w 07-03-13 08:15:45 EST EAGLE 37.5.0
The following tables will be converted:
FEAT_CTRL Table, ID=327
Command Completed.
;
rtrv-upgrade-config
rlghncxa03w 10-02-13 08:15:45 EST EAGLE 42.0.0
Software Access Key no longer required for this system
Configured Upgrade Threshold Type: SET
Command Completed.
;
Related Topics
send-msg
Use this command to manually simulate a system generated message from a user terminal. The parameters (not entered by the user) are defaulted to:
- Origination subsystem = cam_active
- Destination subsystem = orig application ID=appl_ID_ui
- Violation= no report
- Bus = imt choice
- Message length = computed
Parameters
- loc (mandatory)
- The card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1113, 1115, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118
Example
send-msg:loc=1113:os=2:oa=h'28:ds=2:da=h'28:f=7
send-msg:loc=1113:ds=2:oa=h'17:da=h'30:f=11
send-msg:loc=1116:ds=2:oa=h'17::da=h'30:f=12
send-msg:loc=1101:ds=1:da=65:f=27:d0=78:si=3
send-msg:loc=6212:ds=2:oa=h'17:da=h'30:f=11
send-msg:loc=6312:ds=1:da=64:f=171
Dependencies
The value of the da parameter must be valid.
The destination location must be equipped to receive messages.
Card locations xy09 and xy10 cannot be used with bus b and bus a, respectively.
The value of the ds parameter must be valid.
Notes
The bus and sut parameters must be used when sending a message to a MUX card.
If the bus parameter is not specified with a MUX card location on imt B (such as xy10), the bus b value is used instead of the bus a value.
Output
send-msg:loc=1113:os=2:oa=h'28:ds=2:da=h'28:f=7
rlghncxa03w 01-03-13 15:01:02 EST
0061.0019 CARD 1113 PSM ADMIN PSM became active
;
send-msg:loc=1113:ds=2:oa=h'17:da=h'30:f=11
rlghncxa03w 01-03-13 15:02:34 EST
System Buffer sent has following attributes :
Msg Length = H'0006
Dest Card = H'00f4
Orig Subsys = H'0002 Dest Subsys = H'0002
Orig Appl ID = H'0017 Dest Appl ID = H'0030
Func ID = H'000b Bus/Alt/SUT = H’000b
Violation Ind = H’0000
User Message sent to location 1113.
;
send-msg:sut=7:loc=1110:ds=0:da=h'40:f=h'a3:d0=0:bus=b
tekelecstp 06-01-11 11:39:15 EST EAGLE 35.1.0
System Buffer sent has following attributes :
Msg Length = H'0010
Dest Card = H'00ff
Orig Subsys = H'0001 Dest Subsys = H'0000
Orig Appl ID = H'0030 Dest Appl ID = H'0040
Func ID = H'00a3 Bus/Ret/Sut = H'0087
Violation Ind = H'0000
User Message sent to location 1110.
;
send-msg:loc=1101:ds=1:da=65:f=27:d0=78:si=3
slanmfc 11-03-18 05:12:51 EST EAGLE 44.0.0
System Buffer sent has following attributes :
Msg Length = H'001c
Dest Card = H'00f0
Orig Subsys = H'0001 Dest Subsys = H'0001
Orig Appl ID = H'0030 Dest Appl ID = H'0041
Func ID = H'001b Bus/Ret/Sut = H'0002
Violation Ind = H'0018
User Message sent to location 1101.
;
send-msg:loc=6212:ds=2:oa=h'17:da=h'30:f=11
tekelecstp 12-05-11 11:39:15 EST EAGLE 45.0.0
System Buffer sent has following attributes :
Msg Length = H'0006
Dest Card = H'00f4
Orig Subsys = H'0002 Dest Subsys = H'0002
Orig Appl ID = H'0017 Dest Appl ID = H'0030
Func ID = H'000b Bus/Alt/SUT = H’000b
Violation Ind = H’0000
User Message sent to location 6212.
;
set-mem
Use this command to set values in memory in the communication and application processors. If a card is reloaded, these memory changes are lost.
Parameters
- card (optional)
- The card location, in the form of GPLID–Subsystem ID.
- Range:
- GPLID–Subsystem ID
GPLID— atmhc, deirhc, erthc, glshc, hipr2, ipghc, iplhc, ipsg, ipshc, mcphc, oamhc, pktgen, sccphc, siphc, slanhc, ss7hc, utility
Subsystem ID— a, b, act, stb, all
The OAMHC GPL can be specified with any of the subsystem IDs.
For all other GPLs, only the all subsystem ID is valid.
- loc (optional)
- Location. The card location as stenciled on the shelf of the system.
- Range:
- 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115
- op (optional)
- Operation. The operation performed in order to arrive at the final value in the memory location.
Example
set-mem:loc=1109:paddr=h’201000:byte=0:fill=1024
set-mem:card=hipr2-all:paddr=h’202000:word=h’2a:op=and:mask=h’fff
Dependencies
The loc, imt, or card parameter must be specified.
Only one of the loc, imt, and card parameters can be specified in the command.
The card location specified by the loc parameter must be in the database.
All of the subsystem values can be specified with the OAMHC GPLID. The other GPLID values can be specified only with the all subsystem value.
Values of 1114, 1116, 1117, and 1118 cannot be specified for the loc parameter.
The byte, word, or dword parameter must be specified.
Only one of the byte, word, and dword parameters can be specified in the command.
The paddr parameter cannot be specified for an SS7 LIM card.
Memory Type of FWORD is NOT supported at this time.
The addr and paddr parameters cannot be specified together in the command.
The value specified for the fill parameter cannot exceed 65535.
Notes
The imt parameter allows this command to be entered for a card that has not been configured in the system.
Output
set-mem:loc=6205:paddr=h'0345fe:byte=2
rlghncxa03w 12-05-22 21:14:03 EST Rel 45.0.0
SDS Response Code 22 from IMT Address H'00fd - command complete.
;
Related Topics