Updating a High-Capacity Card to Run the BLIXP GPL

High-capacity cards that were issued before EAGLE Release 43.0 may not be loaded with the BLIXP GPL. This procedure updates the high-capacity card with the BLIXP GPL using the flash-card command. The BLIXP GPL is a tar image of all the flash GPLs that are necessary to operate the high-capacity cards. The high-capacity cards are shown in Table 3-7. When the BLIXP GPL is downloaded to the card, the tar image is un-archived and the flash GPLs are loaded onto the card.

Table 3-7 High-Capacity Cards

HC MIM	E5-E1T1	E5-ENET
E5-STC	E5-SLAN	E5-SM4G
E5-ATM	E5-TSM	E5-SM4G

Caution:

The flash-card command cannot be entered if the IMT Rate Change sequence or the Extended Bit Error Rate Test (BERT) is being performed.

The applications and entities supported by the high-capacity cards are shown in Table 3-8.

Table 3-8 High-Capacity Card Applications

High-Capacity Card	Card Name (as shown on the card label)	Application	Application GPL Running on the Card	Supported Entities
HC MIM	HC MIM	SS7ANSI, CCS71TU	SS7HC	E1 or T1 signaling links
E5-E1T1	E5-E1T1	SS7ANSI, CCS71TU	SS7HC	E1 or T1 signaling links
E5-ENET	E5-ENET	SS7IPGW, IPLIM, IPLIMI, IPGWI, IPSG	IPLHC, IPGHC, IPSG	IP signaling links
E5-STC	E5-ENET	EROUTE	ERTHC	EAGLE 5 Integrated Monitoring Support
E5-SM4G	E5-SM4G	VSCCP	SCCPHC	GTT-related features
E5-SLAN	E5-ENET	STPLAN	SLANHC	TCP/IP data links for the STPLAN feature
E5-ENET-B/SLIC	E5-ENET-B SLIC	IPS	IPSHC	Telnet sessions for remote connections to the EAGLE and SEAS terminals for the SEAS over IP feature
E5-ATM	E5-ATM	ATMANSI, ATMITU	ATMHC	ANSI and ITU ATM high-speed signaling links
E5-TSM	E5-TSM	GLS	GLSHC	Gateway Screening related features

Caution:

Before any high-capacity card can be updated with the BLIXP GPL, all the traffic hosted by the high-capacity card must be stopped, and the high-capacity card must be taken out of service.

Canceling the REPT-STAT-SLK and RTRV-SLK Commands

Because the rept-stat-slk and rtrv-slk commands used in this procedure can output information for a long period of time, the rept-stat-slk and rtrv-slk commands can be canceled and the output to the terminal stopped. There are three ways that the rept-stat-slk and rtrv-slk commands can be canceled.

Press the F9 function key on the keyboard at the terminal where the rept-stat-slk or rtrv-slk commands command were entered.
Enter the canc-cmd without the trm parameter at the terminal where the rept-stat-slk or rtrv-slk commands were entered.
Enter the canc-cmd:trm=<xx>, where <xx> is the terminal where the rept-stat-slk or rtrv-slk commands were entered, from another terminal other that the terminal where the rept-stat-slk or rtrv-slk commands were entered. To enter the canc-cmd:trm=<xx> command, the terminal must allow Security Administration commands to be entered from it and the user must be allowed to enter Security Administration commands. The terminal’s permissions can be verified with the rtrv-secu-trm command. The user’s permissions can be verified with the rtrv-user or rtrv-secu-user commands.

For more information about the canc-cmd command, go to Commands User's Guide.

Display the BLIXP GPL on the fixed disk by entering this command.

rtrv-gpl:gpl=blixp

If E5-based control cards are installed in the EAGLE, this is an example of the possible output.

rlghncxa03w 10-12-01 11:34:04 GMT  EAGLE5 43.0.0
GPL Auditing  ON

GPL       CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
BLIXP     1114  133-003-000  133-003-000      133-002-000  133-003-000
BLIXP     1116  133-003-000  133-003-000      133-002-000  133-003-000
BLIXP     1115  -----------  -----------      -----------  -----------

Display the status of the card that is being updated using the rept-stat-card command and specifying the location of the card.

For this example, enter this command.

rept-stat-card:loc=1303

For an HC MIM or E5-E1T1 card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  LIME1     SS7HC      IS-NR          Active     -----
  ALARM STATUS       =  No Alarms.
  IMTPCI  GPL version = 133-002-000
  BLCPLD  GPL version = 133-002-000
  BLDIAG6 GPL version = 133-002-000
  BLBIOS  GPL version = 133-002-000
  BLVXW6  GPL version = 133-002-000
  BLROM1  GPL version = 133-002-000
  PLDPMC1 GPL version = 133-002-000
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  SIGNALING LINK STATUS
      SLK    PST                LS            CLLI
      A      IS-NR              e11303a       -----------
      B      IS-NR              e11303b       -----------
      A1     IS-NR              e11303a       -----------
      B3     IS-NR              e11303b       -----------
Command Completed.

For an E5-E1T1 card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  LIME1     SS7EPM     IS-NR          Active     -----
  ALARM STATUS       =  No Alarms.
  IMTPCI  GPL version = 133-002-000
  BLCPLD  GPL version = 133-002-000
  BLDIAG6 GPL version = 133-002-000
  BLBEPM  GPL version = 133-002-000
  PLDPMC1 GPL version = 133-002-000
  BLVXW6  GPL version = 133-002-000
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  32C ( 90F)     [ALARM TEMP:  60C (140F)]
  PEAK TEMPERATURE:     =  39C (103F)     [06-05-02 13:40]
  SIGNALING LINK STATUS
      SLK    PST                LS            CLLI
      A      IS-NR              e11303a       -----------
      B      IS-NR              e11303b       -----------
      A1     IS-NR              e11303a       -----------
      B3     IS-NR              e11303b       -----------
Command Completed.

For an E5-ENET card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  DCM       IPLHC      IS-NR          Active     -----
  ALARM STATUS       =  No Alarms.
  IMTPCI  GPL version = 133-002-000
  BLCPLD  GPL version = 133-002-000
  BLDIAG6 GPL version = 133-002-000
  BLBEPM  GPL version = 133-002-000
  PLDPMC1 GPL version = 133-002-000
  BLVXW6  GPL version = 133-002-000
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  32C ( 90F)     [ALARM TEMP:  60C (140F)]
  PEAK TEMPERATURE:     =  39C (103F)     [06-05-02 13:40]
  SIGNALING LINK STATUS
      SLK    PST                LS            CLLI
      A      IS-NR              e11303a       -----------
      B      IS-NR              e11303b       -----------
      A1     IS-NR              e11303a       -----------
      B3     IS-NR              e11303b       -----------
Command Completed.

For an E5-STC card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  STC       ERTHC      IS-NR          Active     -----
  ALARM STATUS       = No Alarms.
  IMTPCI  GPL version = 133-002-000
  BLVXW6  GPL version = 133-002-000
  BLDIAG6 GPL version = 133-002-000
  BLBEPM  GPL version = 133-002-000
  BLCPLD  GPL version = 133-002-000
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  61C (142F)
  PEAK TEMPERATURE:     =  61C (142F)     [00-02-14 10:33]
  EROUTE % OCCUP     = 0%
  NTP broadcast = VALID
  STC IP PORT A:                         OOS-MT         Unavail    -----
      ALARM STATUS  = **  0084 IP Connection Unavailable
      ERROR STATUS  = DHCP Lease. Physical Link.
  STC IP PORT B:                         OOS-MT         Unavail    -----
      ALARM STATUS  = **  0084 IP Connection Unavailable
      ERROR STATUS  = DHCP Lease. Physical Link.

Command Completed.

For an E5-SLAN card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  DCM       SLANHC     IS-NR          Active     -----
  ALARM STATUS       = No Alarms.
  IMTPCI  GPL version = 133-002-000
  BLVXW6  GPL version = 133-002-000
  BLDIAG6 GPL version = 133-002-000
  BLBEPM  GPL version = 133-002-000
  BLCPLD  GPL version = 133-002-000
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  60C (140F)
  PEAK TEMPERATURE:     =  63C (146F)     [00-02-12 21:58]
  DLK A   PST        = IS-NR         SST = Avail     AST = -----
  SLAN % EAGLE CAPACITY    = 57%
  SLAN % HOST CAPACITY     = 49%

Command Completed.

For an E5-SM4G card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  DSM       SCCPHC     IS-NR          Active     -----
  ALARM STATUS       = No Alarms.
  IMTPCI  GPL version = 133-002-000
  BLVXW6  GPL version = 133-002-000
  BLDIAG6 GPL version = 133-002-000
  BLBSMG  GPL version = 133-002-000
  BLCPLD  GPL version = 133-002-000
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  31C ( 88F)
  PEAK TEMPERATURE:     =  32C ( 90F)     [07-05-12 15:55]
  SCCP % OCCUP        = 1%

Command Completed.

For an E5-ENET-B/SLIC card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  IPSM      IPSHC      IS-NR          Active     -----
  ALARM STATUS       =  No Alarms.
  IMTPCI  GPL version = 133-002-000
  BLVXW6  GPL version = 133-002-000
  BLDIAG6 GPL version = 133-002-000
  BLBEPM  GPL version = 133-002-000
  BLCPLD  GPL version = 133-002-000
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  32C ( 90F)
  PEAK TEMPERATURE:     =  39C (103F)     [06-05-02 13:40]
  Command Completed.

For an E5-ATM card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0     
CARD   VERSION      TYPE      GPL        PST            SST        AST     
1303   133-003-000  LIMATM    ATMHC      IS-NR          Active     ----- 
  ALARM STATUS       = No Alarms.
  IMTPCI  GPL version = 133-002-000
  BLVXW6  GPL version = 133-002-000
  BLDIAG6 GPL version = 133-002-000
  BLBEPM  GPL version = 133-002-000
  BLCPLD  GPL version = 133-002-000
  IMT BUS A           = Conn
  IMT BUS B           = Conn 
  CURRENT TEMPERATURE   =  38C (101F)
  PEAK TEMPERATURE:     =  38C (101F)     [07-11-23 06:10]
  SIGNALING LINK STATUS
      SLK    PST                LS            CLLI
      A      IS-NR              ls1           -----------       
      

Command Completed.

For an E5-TSM card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0     
CARD   VERSION      TYPE      GPL        PST            SST        AST     
1303   133-003-000  TSM       GLSHC      IS-NR          Active     ----- 
  ALARM STATUS       = No Alarms.
  IMTPCI  GPL version = 133-002-000
  BLVXW6  GPL version = 133-002-000
  BLDIAG6 GPL version = 133-002-000
  BLBEPM  GPL version = 133-002-000
  BLCPLD  GPL version = 133-002-000
  IMT BUS A           = Conn
  IMT BUS B           = Conn 
  CURRENT TEMPERATURE   =  38C (101F)
  PEAK TEMPERATURE:     =  38C (101F)     [07-11-23 06:10]
 
Command Completed.

Continue the procedure by performing one of these actions:

If the card is running one of these application GPLs: SS7HC, SS7EPM, IPLHC, IPGHC, ATMHC, IPSG (shown in the GPL column in the rept-stat-card output in 2), continue the procedure with 5.
If the card is running the ERTHC application GPL, (shown in the GPL column in the rept-stat-card output in 2), continue the procedure with 12.
If the card is running the SLANHC application GPL(shown in the GPL column in the rept-stat-card output in 2), continue the procedure with 7.
If the card is running the IPSHC application GPL, (shown in the GPL column in the rept-stat-card output in 2), continue the procedure with 9.
If the card is running the SCCPHC application GPL, (shown in the GPL column in the rept-stat-card output in 2), continue the procedure with 4.
If the card is running the GLSHC application GPL (shown in the GPL column in the rept-stat-card output in 2), continue the procedure with 3.

Display the GLS cards by entering this command.

rept-stat-card:appl=gls

The output from this command will display the TSMs that are running the GLS GPL and the E5-TSMs that are running the GLSHC GPL.

This is an example of the possible output.


rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1207   133-003-000  TSM       GLSHC      IS-NR          Active     -----
1211   133-003-000  TSM       GLSHC      IS-NR          Active     -----
1303   133-003-000  TSM       GLSHC      IS-NR          Active     -----

Command Completed.

Continue the procedure with 12.

Display the service modules by entering the rept-stat-sccp command.

The output from this command will display the DSMs that are running the VSCCP GPL and the E5-SM4G cards that are running the SCCPHC GPL.

This is an example of the possible output.


rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0

CARD  VERSION      PST             SST        AST       MSU USAGE  CPU USAGE
-----------------------------------------------------------------------------
1303  133-003-000  IS-NR           Active     -----       47%         81%
2103  133-003-000  IS-NR           Active     -----       34%         50%
2111  133-003-000  IS-NR           Active     -----       21%         29%
2115  133-003-000  IS-NR           Active     -----       35%         52%
2117  133-003-000  IS-NR           Active     -----       40%         71%
-----------------------------------------------------------------------------
SCCP Service Average MSU Capacity = 36%       Average CPU Capacity = 56%
Command Completed.

Note:

The rept-stat-sccp command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by the rept-stat-sccp command, refer to the rept-stat-sccp command description in Commands User's Guide.

Continue the procedure with 12.

Display the signaling links associated with the card shown in 2.

Enter the rtrv-slk command with the card location specified in 2. For this example, enter this command.

rtrv-slk:loc=1303

This is an example of the possible output for an HC MIM or E5-E1T1 card.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0

                                   L2T               PCR  PCR   E1   E1
LOC  LINK LSN         SLC TYPE     SET  BPS    ECM   N1   N2    LOC  PORT TS
1303 A    e11303a      0  LIME1    1    64000  PCR   76   3800  1303 2    12
1303 B    e11303b      0  LIME1    1    56000  BASIC ---  ----- 1303 1    2
1303 A1   e11303a      1  LIME1    1    56000  BASIC ---  ----- 1303 1    3
1303 B3   e11303b      1  LIME1    1    56000  BASIC ---  ----- 1303 1    7

This is an example of the possible output for an E5-ENET card.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0

LOC  LINK LSN         SLC TYPE     IPLIML2
1303 A    e11303a      0  IPLIM    M2PA
1303 B    e11303b      0  IPLIM    M2PA
1303 A1   e11303a      1  IPLIM    M2PA
1303 B3   e11303b      1  IPLIM    M2PA

This is an example of the possible output for an E5-ATM card.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0

                                   LP            ATM     
LOC  LINK LSN         SLC TYPE     SET  BPS      TSEL      VCI    VPI   LL     
1303 A    ls2          2  LIMATM   1    1544000  LINE      5      0     0
1303 B    ls1          3  LIMATM   1    1544000  LINE      5      0     0

Deactivate the SS7 signaling links on the card using the dact-slk command.
For this example, enter these commands.

dact-slk:loc=1303:link=a

dact-slk:loc=1303:link=b

dact-slk:loc=1303:link=a1

dact-slk:loc=1303:link=b3

Caution:
These command examples place the signaling links on card 1303 out of service. This will interrupt service on the signaling links on card 1303 and allow the BLIXP GPL to be loaded on to card 1303.

Caution:
If the EAGLE contains only signaling links assigned to the card that is specified in this step, deactivating all of the signaling links that are assigned to the card will take all of these signaling links out of service and will isolate the EAGLE from the network.

When each of these commands have successfully completed, this message should appear.
```
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
Deactivate SLK message sent to card
```
Continue the procedure with 12.
Display the data link, and its status, associated with the card shown in 2. Enter the rept-stat-dlk command with the card location specified in 2.
For this example, enter this command.
rept-stat-dlk:loc=1303
This is an example of the possible output.
```
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
DLK             PST          SST       AST 
1303            IS-NR        Active    ----
  Alarm Status      = No Alarms.
Command Completed.
```
Deactivate the TCP/IP data link on the card that you wish to load the GPL onto using the canc-dlk command. For this example, enter this command.
canc-dlk:loc=1303

Caution:
This command example places the TCP/IP data link on card 1303 out of service. This will interrupt service on the TCP//IP data link on card 1303 and allow the flash GPL to be loaded onto card 1303.

Caution:
If there is only one TCP/IP data link in the EAGLE, placing the card out of service will cause the STPLAN feature to be disabled.

When this command has successfully completed, these messages should appear.
```
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
Deactivate Link message sent to card.
Command Completed.
```
Continue the procedure with 12.

Display the terminal configuration in the database with the rtrv-trm command.

The Telnet terminals associated with the card shown in 9 must be taken out of service. The Telnet terminals are shown in the output with the entry TELNET in the TYPE field. This is an example of the possible output. In this example, the Telnet terminals that must be taken out of service are terminals 17 to 24.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
TRM  TYPE    COMM        FC    TMOUT MXINV DURAL
1    VT320    9600-7-E-1 SW    30    5     99:59:59
2    KSR      9600-7-E-1 HW    30    5     INDEF
3    PRINTER  4800-7-E-1 HW    30    0     00:00:00
4    VT320    2400-7-E-1 BOTH  30    5     00:30:00
5    VT320    9600-7-O-1 NONE  30    5     00:00:30
6    VT320    9600-7-O-1 NONE  30    5     00:00:30
7    PRINTER  9600-7-E–2 HW    30    5     00:30:00
8    KSR     19200-7-E-2 BOTH  30    5     00:30:00
9    VT320    9600-7-O-1 NONE  30    5     00:00:30
10   VT320    9600-7-E-1 HW    30    5     00:30:00
11   VT320    4800-7-E-1 HW    30    5     00:30:00
12   PRINTER  9600-7-E-1 HW    30    4     00:30:00
13   VT320    9600-7-O-1 NONE  30    5     00:30:00
14   VT320    9600-7-E-2 SW    30    8     00:30:00
15   VT320    9600-7-E–2 HW    30    5     00:30:00
16   VT320    9600-7-E-2 BOTH  30    3     00:30:00

TRM  TYPE      LOC              TMOUT MXINV DURAL
17   TELNET    1303             60    5     00:30:00
18   TELNET    1303             60    5     00:30:00
19   TELNET    1303             60    5     00:30:00
20   TELNET    1303             60    5     00:30:00
21   TELNET    1303             60    5     00:30:00
22   TELNET    1303             60    5     00:30:00
23   TELNET    1303             60    5     00:30:00
24   TELNET    1303             60    5     00:30:00
25   TELNET    1203             60    5     00:30:00
26   TELNET    1203             60    5     00:30:00
27   TELNET    1203             60    5     00:30:00
28   TELNET    1203             60    5     00:30:00
39   TELNET    1203             60    5     00:30:00
30   TELNET    1203             60    5     00:30:00
31   TELNET    1203             60    5     00:30:00
32   TELNET    1203             60    5     00:30:00
33   TELNET    1208             60    5     00:30:00
34   TELNET    1208             60    5     00:30:00
35   TELNET    1208             60    5     00:30:00
36   TELNET    1208             60    5     00:30:00
37   TELNET    1208             60    5     00:30:00
38   TELNET    1208             60    5     00:30:00
39   TELNET    1208             60    5     00:30:00
40   TELNET    1208             60    5     00:30:00

Note:

The rtrv-trm command output contains other fields that are not used by this procedure. If you wish to see all the fields displayed by the rtrv-trm command, see the rtrv-trm command description in Commands User's Guide.

Display the status of the terminals with the rept-stat-trm command. This is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
TRM   PST           SST           AST
1     IS-NR         Active        -----
2     IS-NR         Active        -----
3     IS-NR         Active        -----
4     IS-NR         Active        -----
5     IS-NR         Active        -----
6     IS-NR         Active        -----
7     IS-NR         Active        -----
8     IS-NR         Active        -----
9     IS-NR         Active        -----
10    IS-NR         Active        -----
11    IS-NR         Active        -----
12    IS-NR         Active        -----
13    IS-NR         Active        -----
14    IS-NR         Active        -----
15    IS-NR         Active        -----
16    IS-NR         Active        -----
17    IS-NR         Active        -----
18    IS-NR         Active        -----
19    IS-NR         Active        -----
20    IS-NR         Active        -----
21    IS-NR         Active        -----
22    IS-NR         Active        -----
23    IS-NR         Active        -----
24    IS-NR         Active        -----
25    IS-NR         Active        -----
26    IS-NR         Active        -----
27    IS-NR         Active        -----
28    IS-NR         Active        -----
29    IS-NR         Active        -----
30    IS-NR         Active        -----
31    IS-NR         Active        -----
32    IS-NR         Active        -----
33    IS-NR         Active        -----
34    IS-NR         Active        -----
35    IS-NR         Active        -----
36    IS-NR         Active        -----
37    IS-NR         Active        -----
38    IS-NR         Active        -----
39    IS-NR         Active        -----
40    IS-NR         Active        -----

Command Completed.

Place the required terminals out of service using the rmv-trm or the inh-trm command. The function of the rmv-trm and the inh-trm commands are the same. For this example, enter these commands.
rmv-trm:trm=17

rmv-trm:trm=18

rmv-trm:trm=19

rmv-trm:trm=20

rmv-trm:trm=21

rmv-trm:trm=22

rmv-trm:trm=23

rmv-trm:trm=24

Note:
If the terminal that is being taken out of service is the last in service SEAS terminal, theforce=yes parameter must be specified with thermv-trm command for that terminal.

Caution:
Placing the Telnet terminals out of service will disable any Telnet sessions running on these terminals.

If the status of any of the terminals shown in the PST field in 10 is OOS-MT-DSBLD (out-of-service maintenance disabled), the terminal is already out of service and the rmv-trm command does not need to be executed for that terminal.

This message should appear when each of these commands have successfully completed.
```
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
Inhibit message sent to terminal

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
Command Completed.
```
Place the card shown in 2 out of service using the rmv-card or inh-card command. The function of the rmv-card and the inh-card commands are the same.
For this example, enter this command.

rmv-card:loc=1303

When this command has successfully completed, this message should appear.
```
rlghncxa03w 10-12-01  11:11:28 GMT  EAGLE5 43.0.0
Card has been inhibited.
```
The force=yes parameter must be specified in this step if any of these conditions exist.
- The HC MIM, E5-E1T1, E5-ATM, or E5-ENET card contains the last signaling link in a linkset.
- The E5-TSM is the last GLS card that is in service.
- The service module is the last service module that is in service.

Load the approved version of the BLIXP GPL onto the card that was inhibited in 12 using the flash-card command with the code=appr and the card location parameters.

Caution:

The flash-card command cannot be entered if the IMT Rate Change sequence or the Extended Bit Error Rate Test (BERT) is being performed.

For this example, enter this command.

flash-card:code=appr:loc=1303

When this command has successfully completed, these messages should appear.

   
    rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
    Flash Card: Downloading BLIXP on card 1303.
;
    rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
    Flash Card: Card 1303 download BLIXP complete.
;
    rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
    Flash Card: Activating BLIXP on card 1113.
;
    rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
    Flash Card: Card 1303 activation BLIXP complete.
;
    rrlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
    Command Completed.

Put the card that was inhibited in 12 back into service using the rst-card or alw-card command. The function of the rst-card and the alw-card commands are the same.
The rst-card or alw-card command also loads the approved version of the BLIXP GPL onto the card.

For this example, enter this command.

rst-card:code=appr:loc=1303

When this command has successfully completed, this message should appear.
```
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
Card has been allowed.
```

Verify that the BLIXP GPL from 14 has loaded and that the card has returned to its in-service normal (IS-NR) state using the rept-stat-card command.

For this example, enter this command.

rept-stat-card:loc=1303

For an HC MIM or E5-E1T1 card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  LIME1     SS7HC      IS-NR          Active     -----
  ALARM STATUS       =  No Alarms.
  BLIXP   GPL version = 133-003-000  
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  SIGNALING LINK STATUS
      SLK    PST                LS            CLLI
      A      OOS-MT-DSBLD       e11303a       -----------
      B      OOS-MT-DSBLD       e11303b       -----------
      A1     OOS-MT-DSBLD       e11303a       -----------
      B3     OOS-MT-DSBLD       e11303b       -----------
Command Completed.

For an E5-E1T1 card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  IPLIM     SS7EPM     IS-NR          Active     -----
  ALARM STATUS       =  No Alarms.
  BLIXP   GPL version = 133-003-000 
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  32C ( 90F)     [ALARM TEMP:  60C (140F)]
  PEAK TEMPERATURE:     =  39C (103F)     [06-05-02 13:40]
  SIGNALING LINK STATUS
      SLK    PST                LS            CLLI
      A      IS-NR              e11303a       -----------
      B      IS-NR              e11303b       -----------
      A1     IS-NR              e11303a       -----------
      B3     IS-NR              e11303b       -----------
Command Completed.

For an E5-ENET card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  DCM       IPLHC      IS-NR          Active     -----
  ALARM STATUS       =  No Alarms.
  BLIXP   GPL version = 133-003-000 
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  32C ( 90F)     [ALARM TEMP:  60C (140F)]
  PEAK TEMPERATURE:     =  39C (103F)     [06-05-02 13:40]
  SIGNALING LINK STATUS
      SLK    PST                LS            CLLI
      A      IS-NR              e11303a       -----------
      B      IS-NR              e11303b       -----------
      A1     IS-NR              e11303a       -----------
      B3     IS-NR              e11303b       -----------
Command Completed.

For an E5-STC card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  STC       ERTHC      IS-NR          Active     -----
  ALARM STATUS       =  No Alarms.
  BLIXP   GPL version = 133-003-000 
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  61C (142F)
  PEAK TEMPERATURE:     =  61C (142F)     [06-05-02 13:40]
  NTP broadcast = VALID
  STC IP PORT A:                         OOS-MT         Unavail    -----
      ALARM STATUS  = **  0084 IP Connection Unavailable
      ERROR STATUS  = DHCP Lease. Physical Link.
  STC IP PORT B:                         OOS-MT         Unavail    -----
      ALARM STATUS  = **  0084 IP Connection Unavailable
      ERROR STATUS  = DHCP Lease. Physical Link.
Command Completed.

For an E5-SLAN card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  DCM       SLANHC     IS-NR          Active     -----
  ALARM STATUS       =  No Alarms.
  BLIXP   GPL version = 133-003-000 
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  60C (140F)
  PEAK TEMPERATURE:     =  63C (146F)     [00-02-12 21:58]
  DLK A   PST        = IS-NR         SST = Avail     AST = -----
  SLAN % EAGLE CAPACITY    = 57%
  SLAN % HOST CAPACITY     = 49%
Command Completed.

For an E5-SM4G card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  DSM       SCCPHC     IS-NR          Active     -----
  ALARM STATUS       =  No Alarms.
  BLIXP   GPL version = 133-003-000 
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  31C ( 88F)
  PEAK TEMPERATURE:     =  32C ( 90F)     [07-05-12 15:55]
  SCCP % OCCUP        = 1%

Command Completed.

For an E5-ENET-B or SLIC card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
CARD   VERSION      TYPE      GPL        PST            SST        AST
1303   133-003-000  IPSM      IPSHC      IS-NR          Active     -----
  ALARM STATUS       =  No Alarms.
  BLIXP   GPL version = 133-003-000 
  IMT BUS A           = Conn
  IMT BUS B           = Conn
  CURRENT TEMPERATURE   =  32C ( 90F)
  PEAK TEMPERATURE:     =  39C (103F)     [06-05-02 13:40]
  Command Completed.

For an E5-ATM card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0     
CARD   VERSION      TYPE      GPL        PST            SST        AST     
1303   133-003-000  LIMATM    ATMHC      IS-NR          Active     ----- 
  ALARM STATUS       = No Alarms.
  BLIXP   GPL version = 133-003-000 
  IMT BUS A           = Conn
  IMT BUS B           = Conn 
  CURRENT TEMPERATURE   =  38C (101F)
  PEAK TEMPERATURE:     =  38C (101F)     [07-11-23 06:10]
  SIGNALING LINK STATUS
      SLK    PST                LS            CLLI
      A      IS-NR              ls1           -----------       
      

Command Completed.

For an E5-TSM card, this is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0     
CARD   VERSION      TYPE      GPL        PST            SST        AST     
1303   133-003-000  TSM       GLSHC      IS-NR          Active     ----- 
  ALARM STATUS       = No Alarms.
  BLIXP   GPL version = 133-003-000 
  IMT BUS A           = Conn
  IMT BUS B           = Conn 
  CURRENT TEMPERATURE   =  38C (101F)
  PEAK TEMPERATURE:     =  38C (101F)     [07-11-23 06:10]
 
Command Completed.

Note:

If the version number of the BLIXP GPL that is shown in this step is not the version specified in 1, contact the Customer Care Center. Refer to the My Oracle Support (MOS) section for the contact information.

Continue the procedure by performing one of these actions.

If card is running one of these application GPLs: SS7HC, SS7EPM, IPLHC, IPGHC, ATMHC, IPSG (shown in the GPL column in the rept-stat-card output in 15), continue the procedure with 16.
If card is running one of these application GPLs: ERTHC, GLSHC, or SCCPHC, (shown in the GPL column in the rept-stat-card output in 15), continue the procedure with 22.
If the card is running the SLANHC application GPL, (shown in the GPL column in the rept-stat-card output in 15), continue the procedure with 18.
If the card is running the IPSHC application GPL, (shown in the GPL column in the rept-stat-card output in 15), continue the procedure with 20.

Place the signaling links that were deactivated in 6 back into service using the act-slk command.
For this example, enter these commands.

act-slk:loc=1303:link=a

act-slk:loc=1303:link=b

act-slk:loc=1303:link=a1

act-slk:loc=1303:link=b3

When each of these commands have successfully completed, this message should appear.
```
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
Activate SLK message sent to card
```

Verify that the signaling links activated in 16 are back in service using the rept-stat-slk command with the card location and signaling link.

For this example, enter these commands.

rept-stat-slk:loc=1303:link=a

This is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
SLK      LSN       CLLI        PST          SST       AST
1303,A   e11303a   ----------- IS-NR        Avail     ----
  ALARM STATUS       = No Alarms.
  UNAVAIL REASON     = --

rept-stat-slk:loc=1303:link=b

This is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
SLK      LSN       CLLI        PST          SST       AST
1303,B   e11303b   ----------- IS-NR        Avail     ----
  ALARM STATUS       = No Alarms.
  UNAVAIL REASON     = --

rept-stat-slk:loc=1303:link=a1

This is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
SLK      LSN       CLLI        PST          SST       AST
1303,A1  e11303a   ----------- IS-NR        Avail     ----
  ALARM STATUS       = No Alarms.
  UNAVAIL REASON     = --

rept-stat-slk:loc=1303:link=b3

This is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
SLK      LSN       CLLI        PST          SST       AST
1303,B3  e11303b   ----------- IS-NR        Avail     ----
  ALARM STATUS       = No Alarms.
  UNAVAIL REASON     = --
Command Completed.

Continue the procedure with 22.

Place the TCP/IP data link that was deactivated in 8 back into using the act-dlk command. For this example, enter this command.
act-dlk:loc=1303
When this command has successfully completed, this message should appear.
```
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0 
Activate Link message sent to card.
```
Verify that the TCP/IP data link activated in 18 is back in service with the rept-stat-dlk command. For this example, enter this command.
rept-stat-dlk:loc=1303
This is an example of the possible output.
```
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
DLK             PST          SST       AST 
1303            IS-NR        Active    ----
  Alarm Status      = No Alarms.
Command Completed.
```
Continue the procedure with 22.
Put the required terminals back into service with the rst-trm or alw-trm command. The function of the rst-trm and the alw-trm commands are the save. For this example, enter these commands.
rst-trm:trm=17
rst-trm:trm=18
rst-trm:trm=19
rst-trm:trm=20
rst-trm:trm=21
rst-trm:trm=22
rst-trm:trm=23
rst-trm:trm=24
This message should appear when each of these commands have successfully completed.
```
rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
Allow message sent to terminal

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
Command Completed.
```

Verify that the terminals are in service with the rept-stat-trm command. This is an example of the possible output.

rlghncxa03w 10-12-01 09:12:36 GMT EAGLE5 43.0.0
TRM   PST           SST           AST
1     IS-NR         Active        -----
2     IS-NR         Active        -----
3     IS-NR         Active        -----
4     IS-NR         Active        -----
5     IS-NR         Active        -----
6     IS-NR         Active        -----
7     IS-NR         Active        -----
8     IS-NR         Active        -----
9     IS-NR         Active        -----
10    IS-NR         Active        -----
11    IS-NR         Active        -----
12    IS-NR         Active        -----
13    IS-NR         Active        -----
14    IS-NR         Active        -----
15    IS-NR         Active        -----
16    IS-NR         Active        -----
17    IS-NR         Active        -----
18    IS-NR         Active        -----
19    IS-NR         Active        -----
20    IS-NR         Active        -----
21    IS-NR         Active        -----
22    IS-NR         Active        -----
23    IS-NR         Active        -----
24    IS-NR         Active        -----
25    IS-NR         Active        -----
26    IS-NR         Active        -----
27    IS-NR         Active        -----
28    IS-NR         Active        -----
29    IS-NR         Active        -----
30    IS-NR         Active        -----
31    IS-NR         Active        -----
32    IS-NR         Active        -----
33    IS-NR         Active        -----
34    IS-NR         Active        -----
35    IS-NR         Active        -----
36    IS-NR         Active        -----
37    IS-NR         Active        -----
38    IS-NR         Active        -----
39    IS-NR         Active        -----
40    IS-NR         Active        -----

Command Completed.

This procedure is finished.

Figure 3-9 Updating a High-Capacity Card to Run the BLIXP GPL

Sheet 1 of 4

Sheet 2 of 4

Sheet 3 of 4

Sheet 4 of 4