0570 - Incompatible Flash Image for sys rel

The new card inserted into system with a flash image is not compatible with the system release. The card is auto-inhibited. A manual flash download is required.

Example

isht01 09-07-21 09:19:16 EST  EAGLE5 41.1  
  
ALARM STATUS       = **  0570 Incompatible flash image for sys rel
   99  Inserted H/W is not compatible with the provisioned slot
                   HW VERIFICATION CODE: 98

Alarm Level: Major

Recovery

1. Enter the command to load and activate the approved GPL onto the inhibited card:
   flash-card:code=appr:loc=xxxx:force=yes

   where xxxx is the card location used in the previous step. The optional force=yes is used to force the command to work on an IS-NR card. Links provisioned on the card are inhibited during command execution. The card and inhibited links are restored to their previous state when the command is completed.

   Example of the output using card location 1112:

   Command Accepted - Processing
   
       tekelecstp 18-01-18 16:06:22 MST  EAGLE 46.5.1.5.0-73.3.0
       flash-card:code=appr:force=yes:loc=1112
       Command entered at terminal #1.
   ;
   
       tekelecstp 18-01-18 16:06:55 MST  EAGLE 46.5.1.5.0-73.3.0
       Flash Card: FLASH GPL required to be downloaded on card 1112
       BLMCAP    : Running version 143-001-000  Expected version 143-002-000
   
   ;
       tekelecstp 18-01-18 16:07:14 MST  EAGLE 46.5.1.5.0-73.3.0
       Flash Card: Downloading BLMCAP on card 1112
       Flash Card: Card(s) will reset after the flash GPL download.
   
   ;
       tekelecstp 18-01-18 16:07:56 MST  EAGLE 46.5.1.5.0-73.3.0
       Flash Card: Activating BLMCAP on card 1112
   
   ;
       tekelecstp 18-01-18 16:08:25 MST  EAGLE 46.5.1.5.0-73.3.0
       Flash Card: Card 1112 flash activation complete.
   ;
       Flash Card: Activating links on card 1112. 
   ;
       tekelecstp 18-01-11 16:09:11 EST  EAGLE5 39.0.0
       Command Completed.

2. Enter the command to put the card that was inhibited in 1 back into service:
   alw-card:loc=xxxx

   where xxxx is the card location used in 1.

   Example of the output:

   RLGHNCXA03W  00-06-05  11:11:28 EDT  EAGLE 35.0.0
   Card has been allowed.

   Note:

   Allow the card to run for 5 minutes before continuing.
3. Enter the command to activate all links on the card.
   act-slk:loc=xxxx:link=y

   where xxxx is the card location identified in the output and y is the link.

4. Enter the command to verify all links on the card are active.
   rept-stat-slk:loc=xxxx:link=y

   where xxxx is the card location identified in the output and y is the link

5. Enter the command to verify the approved GPLs match the running GPLs:
   rept-stat-gpl:gpl=xxxxxxx

   where xxxxxxx is the GPL identified in the output.

6. If the GPLs match, you have completed this procedure.

   If the GPLs do not match, continue with the following step.

7. Repeat this procedure for each card that shows ALM in the output.
8. If the same card shows in an alarm condition after executing the procedure, please contact My Oracle Support (MOS).