Upgrading Flash-Based GPL on Non-In-Service and Unprovisioned Network Cards

A Upgrading Flash-Based GPL on Non-In-Service and Unprovisioned Network Cards

This procedure determines any BLIXP, BLMCAP, BLDC64, BLSLC32, or BLSLC64 cards that are inhibited, and updates each card with its target release GPLs. (See Software Release Numbering for complete list of flash GPLs.)

Issue the command to display the GPL status.

rept-stat-gpl:gpl=XXXX

(Where XXXX is the GPL listed in the header of the procedure)

Response to the command is displayed.

Record any card which shows an alarm:

______________

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    rept-stat-gpl:gpl=xxxx
    Command entered at terminal #10.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    GPL Auditing  ON

    APPL       CARD      RUNNING            APPROVED      TRIAL
    XXXXXX     1101      xxx-xxx-xxx        xxx-xxx-xxx   xxx-xxx-xxx 
    XXXXXX     1103      xxx-xxx-xxx        xxx-xxx-xxx   xxx-xxx-xxx 
    XXXXXX     1111      xxx-xxx-xxx ALM    xxx-xxx-xxx   xxx-xxx-xxx 
    Command Completed.
;

Issue the status command for specific card.

rept-stat-card:loc=XXXX

(Where XXXX is the card location recorded in the previous step.)

Response to the command is displayed.

If the PST for the card is OOS-MT-DSBLD or the command is rejected with MTT error E2144 Cmd Rej: Location invalid for hardware configuration, go to step 4.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE      APPL       PST            SST       AST
    1111   -----------  DSM       VSCCP      OOS-MT-DSBLD   Manual    ---
      ALARM STATUS       = No Alarms.
      BPDCM GPL version  = 002-115-000
      IMT BUS A          = -----
      IMT BUS B          = -----
      SCCP % OCCUP       = 0%
    Command Completed.

Issue the command to inhibit card.

inh-card:loc=XXXX

Response to the command is displayed.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been inhibited.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;

Issue the command to flash all GPLs on the card.
flash-card:code=appr:loc=XXXX

Note:
This command causes the card to boot.

Response to the flash command is displayed.

Wait for the card to finish loading before proceeding.
```
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    flash-card:code=appr:loc=XXXX
    Command entered at terminal #10.
;




    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;
```

If step 3 was executed, issue the command to allow card.

alw-card:loc=XXXX

Response to the command is displayed.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been allowed.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;

Repeat Steps 2 – 5 for all cards recorded in step 1.
Repeat Steps 1 – 6 for each group of Flash-Based cards (see Software Release Numbering.)