Recovery Procedures

6 Recovery Procedures

Before executing any of these procedures, contact My Oracle Support at Oracle Support Contacts Global Directory [see My Oracle Support (MOS).] In the event that other platforms are being upgraded in parallel, a determination whether recovery action is required on those platforms is required. Persons performing the upgrade should be familiar with these upgrade documents.

Backout Setup Procedures

Execute this section only if there is a problem and it is desired to revert back to the pre-upgrade version of the software.

WARNING:

Do not attempt to perform these backout procedures without first contacting the My Oracle Support at Oracle Support Contacts Global Directory.

Revert MASP, MCPM and IPSM to VxWorks6.4

Execute this section only if there is a problem and it is desired to revert to the pre-upgrade version of the software for the MASP, MCPM and IPSM cards.

If the source release is 46.5 or prior and the target release is 46.6 or later, then execute Revert IPS (ENET-B) cards on VxWorks6.4 through Revert the MASP Card to VxWorks6.4.

If system is running on VxWorks6.9 but pre-upgrade version is on VxWorks6.4 then following are the steps to revert the system to former state:

First revert the cards to VxWorks6.4 (Revert IPS (ENET-B) cards on VxWorks6.4 to Revert the MASP Card to VxWorks6.4)
Follow the normal recovery procedure A, B or C

Revert IPS (ENET-B) cards on VxWorks6.4

This procedure is to revert the IPSM cards to VxWorks6.4.

Execute the below procedure for every IPSM card present in the system.

SHOULD THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.

If source release is 46.5 or prior, issue the card status command.

REPT-STAT-CARD:APPL=IPS

Response to the card status command is displayed.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE      GPL        PST            SST        AST
    XXXX   XXX-XXX-XXX  IPSM      IPSHC      IS-NR          Active     ----
    XXXX   XXX-XXX-XXX  IPSM      IPSHC      IS-NR          Active     ----

    Command Completed.
;

For each card listed above, issue the GPL status commend.
REPT-STAT-GPL:LOC=XXXX
(Where XXXX is the location of the IPSM card)

Response to the GPL status command is displayed.
If card is running BLDC32, go to next step. Otherwise repeat Step 2 for next IPSM card listed in Step 1.
```
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y
    GPL        CARD      RUNNING            APPROVED      TRIAL
    IPSHC69      XXXX    XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
           BLDC32        YYY-YYY-YYY        YYY-YYY-YYY   YYY-YYY-YYY

    Command Completed.
;
```
Issue command to inhibit the card.
INH-CARD:LOC=XXXX
(Where XXXX is the location of the IPSM card use in previous command.)

Response to the inhibit command is displayed.
```
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been inhibited.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.

;
```
Note:
Wait for the card to boot and return to the IMT bus.

Download target-release flash to the IPSM card.

INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLMCAP

(Where XXXX is the location used in the previous command)

Response to flash initialization is shown.

Verify UAM 0004 is displayed.


    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    FLASH Memory Download for card xxxx started.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    FLASH Memory Download for card xxxx completed.
; 
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
*   8003.0004  * GPL SYSTEM BLMCAP       Card is running non-activated GPL
;

Note:

Wait for card to boot and return to the IMT bus.

Issue command to activate the flash image.
ACT-FLASH:loc=XXXX
(Where XXXX is the location of the IPSM card used in the previous command)

Response to the activate command is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Activation for card XXXX Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Activation for card XXXX Completed.
;
```
Issue the allow command to reload the IPSM card.
ALW-CARD:LOC=XXXX
(Where XXXX is the location of the IPSM card used in the previous command)

Response to allow-card command is shown.
```
eaglestp YY-MM-DD hh:mm:ssc TTTT EAGLE XX.x.x.x.x-YY.y.y 
    Card has been allowed.
;
```
Issue command to report the GPLs running on the IPSM card.
REPT-STAT-GPL:LOC=XXXX
(Where XXXX is the location of the IPSM card used in the previous command)

Response to GPL status command.

Verify that IPSM card is running BLMCAP flash GPL.
```
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    GPL Auditing  ON

    GPL        CARD      RUNNING            APPROVED      TRIAL
    IPSHC      XXXX      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
           BLMCAP        YYY-YYY-YYY        YYY-YYY-YYY   YYY-YYY-YYY

    Command Completed.
;
```
If this is the last card listed in Step 1, continue to next procedure. Otherwise, repeat Steps 2 - 7 for the next card listed in Step 1.

Note:
Wait till this flashed IPSM card to complete reloading before proceeding to next step.

Revert IPSM Application Running on SLIC to VxWorks6.4

This procedure reverts the SLIC card running the IPS application to VxWorks6.4.

Execute the below procedure for every SLIC card with IPS application present in the system.

SHOULD THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.

If source release is 46.5 or prior, issue the card status command.

REPT-STAT-CARD:APPL=IPS

Response to the card status command is displayed.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE      GPL        PST            SST        AST
    XXXX   XXX-XXX-XXX  SLIC      IPSHC      IS-NR          Active     ----
    XXXX   XXX-XXX-XXX  SLIC      IPSHC      IS-NR          Active     ----

    Command Completed.
;

For each card with type equal to SLIC listed above, issue the GPL status command.
REPT-STAT-GPL:LOC=XXXX
(Where XXXX is the location of the IPSM/SLIC card slot listed in previous step.)

Response to the card status command is displayed.

If card is running BLSL932, go to next step. Otherwise repeat Step 2 for next SLIC card listed in Step 1.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y
    GPL        CARD      RUNNING            APPROVED      TRIAL
    IPSHC69    XXXX      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
           BLSL932       YYY-YYY-YYY        YYY-YYY-YYY   YYY-YYY-YYY

    Command Completed.
;
```
Issue command to inhibit the card.
INH-CARD:LOC=XXXX
(Where XXXX is the location of the IPSM/SLIC card)

Response to the inhibit command is displayed.
```
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been inhibited.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.

;
```
Note:
Wait for the card to boot and return to the IMT bus.
Issue flash command to download target-release flash to the IPSM/SLIC card.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLSLC32
(Where XXXX is the location used in the previous command)

Response to flash initialization is shown.

Verify UAM 0004 is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    FLASH Memory Download for card xxxx started.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    FLASH Memory Download for card xxxx completed.
; 
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
*   8003.0004  * GPL SYSTEM BLSLC32      Card is running non-activated GPL
;
```
Note:
Wait for card to boot and return to the IMT bus.
Issue command to activate the flash image.
ACT-FLASH:loc=XXXX
(Where XXXX is the location of the IPSM/SLIC card used in the previous command.)

Response to the activate command is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Activation for card XXXX Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Activation for card XXXX Completed.
;
```
Issue the allow command to reload the IPSM/SLIC card.
ALW-CARD:LOC=XXXX
(Where XXXX is the location of the IPSM/SLIC card used in the previous command.)

Response to allow-card command is shown.
```
    eaglestp YY-MM-DD hh:mm:ssc TTTT EAGLE XX.x.x.x.x-YY.y.y 
    Card has been allowed.
;
```
Issue command to report GPL status.
REPT-STAT-GPL:LOC=XXXX
(Where XXXX is the location of the IPSM/SLIC card used in the previous command.)

Response to GPL status command

Verify that IPSM/SLIC card is running BLSLC32 flash GPL.
```
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    GPL Auditing  ON

    GPL        CARD      RUNNING            APPROVED      TRIAL
    IPSHC      XXXX      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
           BLSLC32       YYY-YYY-YYY        XXX-XXX-XXX   YYY-YYY-YYY

    Command Completed.
;
```
If this is last card listed in Step 1, continue to next procedure. Otherwise, repeat Steps 2 - Step 6 for the next card listed in Step 1.

Note:
Wait till this flashed IPSM/SLIC card to complete reloading before proceeding to next step.

Revert MCPM Cards on VxWorks6.4

This procedure is to revert the MCPM cards to VxWorks6.4.

Execute the below procedure for every MCPM card present in the system.

SHOULD THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.

If source release is 46.5 or prior, issue the card status command.

REPT-STAT-CARD:APPL=MCP

Response to the card status command is displayed.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE      GPL        PST            SST        AST
    XXXX   XXX-XXX-XXX  MCPM      MCPHC      IS-NR          Active     ----
    XXXX   XXX-XXX-XXX  MCPM      MCPHC      IS-NR          Active     ----

    Command Completed.
;

For each card with type equal to SLIC listed above, issue the GPL status command.
REPT-STAT-GPL:LOC=XXXX
(Where XXXX is the location of the MCPM card.)

Response to the card status command is displayed.

If card is running BLDC32, go to next step. Otherwise repeat Step 2 for next MCPM card listed in Step 1.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y
    GPL        CARD      RUNNING            APPROVED      TRIAL
    MCPHC69      XXXX   XXX-XXX-XXX       XXX-XXX-XXX   XXX-XXX-XXX
           BLDC32       YYY-YYY-YYY       YYY-YYY-YYY   YYY-YYY-YYY

    Command Completed.
;
```
Issue command to inhibit the card.
INH-CARD:LOC=XXXX
(Where XXXX is the location of the MCP card use in previous command.)

Response to the inhibit command is displayed.
```
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been inhibited.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.

;
```
Note:
Wait for the card to boot and return to the IMT bus.
Download target-release flash to the MCPM card.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLMCAP
(Where XXXX is the location used in the previous command)

Response to flash initialization is shown.

Verify UAM 0004 is displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    FLASH Memory Download for card xxxx started.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    FLASH Memory Download for card xxxx completed.
; 
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
*   8003.0004  * GPL SYSTEM BLMCAP       Card is running non-activated GPL
;
```
Note:
Wait for card to boot and return to the IMT bus.
Issue command to activate the flash image.
ACT-FLASH:loc=XXXX
(Where XXXX is the location of the MCPM card used in the previous command.)

Response to the activate command is displayed.
```
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Activation for card XXXX Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Activation for card XXXX Completed.
;
```
Run the target-release GPL on the MCPM card.
ALW-CARD:LOC=XXXX
(Where XXXX is the location of the MCP card used in the previous command.)

Response to allow-card command is shown.
```
    eaglestp YY-MM-DD hh:mm:ssc TTTT EAGLE XX.x.x.x.x-YY.y.y 
    Card has been allowed.
;
```
Issue command to report the GPLs running on the MCPM card.
REPT-STAT-GPL:LOC=XXXX
(Where XXXX is the location of the MCP card used in the previous command.)

Response to GPL status command

Verify that MCPM card is running BLMCAP flash GPL.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    GPL Auditing  ON

    GPL        CARD      RUNNING            APPROVED      TRIAL
    MCPHC      XXXX      XXX-XXX-XXX        XXX-XXX-XXX   -----------
       BLMCAP            YYY-YYY-YYY        XXX-XXX-XXX   YYY-YYY-YYY


    Command Completed.
;
```
If this is last card listed in Step 1, continue to next procedure. Otherwise, repeat Steps 2 - Step 6 for the next card listed in Step 1.

Note:
Wait till this flashed MCPM card to complete reloading before proceeding to next step.

Revert MCPM Application Running on SLIC card to VxWorks6.4

This procedure is to revert the SLIC card with MCPM application to VxWorks6.4.

Execute the below procedure for every SLIC card running the MCP application present in the system.

SHOULD THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.

If source release is 46.5 or prior, issue the card status command.

REPT-STAT-CARD:APPL=MCP

Response to the card status command is displayed.


    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE      GPL        PST            SST        AST
    XXXX   XXX-XXX-XXX  SLIC      MCPHC      IS-NR          Active     ----
    XXXX   XXX-XXX-XXX  SLIC      MCPHC      IS-NR          Active     ----

    Command Completed.
;

For each MCPM/SLIC card listed above, issue the GPL status command.
REPT-STAT-GPL:LOC=XXXX
(Where XXXX is the location of the MCPM/SLIC card slot listed in previous step.)

Response to the card status command is displayed.

If card is running BLSL932, go to next step. Otherwise repeat Step 2 for next card listed in Step 1.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y
    GPL        CARD      RUNNING            APPROVED      TRIAL
    MCPHC69      XXXX     XXX-XXX-XXX       XXX-XXX-XXX  XXX-XXX-XXX
           BLSL932        YYY-YYY-YYY       YYY-YYY-YYY  YYY-YYY-YYY

    Command Completed.
;
```
Issue command to inhibit the card.
INH-CARD:LOC=XXXX
(Where XXXX is the location of the MCPM/SLIC card use in previous command.)

Response to the inhibit command is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been inhibited.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.

;
```
Note:
Wait for the card to boot and return to the IMT bus.
Issue flash command to download target-release flash to the MCPM card.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLSLC32
(Where XXXX is the location used in the previous command)

Response to flash initialization is shown.

Verify UAM 0004 is displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    FLASH Memory Download for card xxxx started.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    FLASH Memory Download for card xxxx completed.
; 
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
*   8003.0004  * GPL SYSTEM BLSLC32       Card is running non-activated GPL
;
```
Note:
Wait for card to boot and return to the IMT bus.
Issue command to activate the flash image.
ACT-FLASH:loc=XXXX
(Where XXXX is the location of the MCPM card used in the previous command.)

Response to the activate command is displayed.
```
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Activation for card XXXX Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Activation for card XXXX Completed.
;
```
Run the target-release GPL on the MCPM card.
ALW-CARD:LOC=XXXX
(Where XXXX is the location of the MCPM\SLIC card used in the previous command.)

Response to allow-card command is shown.
```
    eaglestp YY-MM-DD hh:mm:ssc TTTT EAGLE XX.x.x.x.x-YY.y.y 
    Card has been allowed.
;
```
Retrieve status of the MCPM\SLIC card.
REPT-STAT-GPL:LOC=XXXX
(Where XXXX is the location of the MCPM card used in the previous command.)

Response to GPL status command

Verify that MCPM/SLIC card is running BLSLC32 flash GPL.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    GPL Auditing  ON

    GPL        CARD      RUNNING            APPROVED      TRIAL
    MCPHC      XXXX      XXX-XXX-XXX        XXX-XXX-XXX   -----------
       BLSLC32            YYY-YYY-YYY        XXX-XXX-XXX   YYY-YYY-YYY


    Command Completed.
;
```
If this is last card listed in Step 1, continue to next procedure. Otherwise, repeat Steps 2 - Step 6 for the next card listed in Step 1.

Note:
Wait till this flashed MCPM/SLIC card to complete reloading before proceeding to next step.

Revert the MASP Card to VxWorks6.4

This procedure is to revert the MASP cards to VxWorks6.4.

SHOULD THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.

If source release is 46.5 or prior, issue the card status to verify the location of the active/standby MASP slots.
REPT-STAT-CARD:APPL=OAM
Response to the card status command is displayed.

Record the MASP in the standby role:

Standby: 1113 or 1115
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE    GPL        PST            SST        AST
    
    1113    XXX-XXX-XXX E5MCAP  OAMHC      IS-NR          Active     -----
    1115    XXX-XXX-XXX E5MCAP  OAMHC      IS-NR          Standby    -----
    Command Completed.
;
```
Report the GPLs running on the card location.
REPT-STAT-GPL:LOC=XXXX
(Where XXXX is the location of the standby MASP slot display in the above step.)

Response from the retrieve command is displayed.

Verify that card is running the BLDC32 flash GPL
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y
    GPL        CARD      RUNNING            APPROVED      TRIAL
    OAMHC      XXXX      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
           BLDC32        YYY-YYY-YYY        YYY-YYY-YYY   YYY-YYY-YYY

    Command Completed.
;
```
Issue the command to inhibit the standby MASP.
INH-CARD:LOC=XXXX
(Where XXXX is the location of the standby MASP slot used in previous command.)

Response to the inhibit command is displayed.

Verify UAM 514 is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y
    Card is inhibited.
;

    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y
   **  5045.0514 ** CARD XXXX OAMHC         Standby MASP is inhibited
;
```
Note:
Wait for the card to boot and return to the IMT bus.
Issue pass command to enable the Shell command.
PASS:LOC=XXXX:SHELLCMD="-enable"
(Where XXXX is the location of the Standby MASP)

Response to the pass command.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y
    PASS: Command sent to card
;
```
Set the global variable to revert the bootloader.
PASS:lOC=XXXX:SHELLCMD="g_backout_6_9_bootloader=1"
(Where XXXX is the location of the Standby MASP)

Response to the pass command.
```
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y
    PASS: Command sent to card
;
```
Issue flash command to download the bootloader image.
INIT-FLASH:LOC=XXXX:MODE=RPLCEBL:BITS=32
(Where XXXX is the location of the Standby MASP slot used in the previous command.)

Response to flash command is shown.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y
    BOOTLOADER change for card XXXX SUCCESSFUL.
;

    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y
    Command Completed.
;
```
Download target-release flash to the standby MASP card.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLMCAP
(Where XXXX is the location used in the previous command.)

Response to flash initialization is shown.

Verify UAM 0004 is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    FLASH Memory Download for card xxxx started.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    FLASH Memory Download for card xxxx completed.
; 
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
*   8003.0004  * GPL SYSTEM BLMCAP       Card is running non-activated GPL
;
```
Note:
Wait for card to boot and return to the IMT bus.

Retrieve the GPLs running on the card location.

REPT-STAT-GPL:LOC=XXXX

(Where XXXX is the location of the standby MASP slot used in the previous command.)

Response to the GPL status command is displayed.

Verify that card is running BLMCAP GPL.

    
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y
    GPL        CARD      RUNNING            APPROVED      TRIAL
    OAMHC      XXXX      -----------        -----------   -----------
           BLMCAP        YYY-YYY-YYY+       YYY-YYY-YYY   YYY-YYY-YYY

    Command Completed.
;

Issue command to activate the flash on standby MASP.
ACT-FLASH:LOC=XXXX
(Where XXXX is the location of the standby MASP used in the previous command)

Response to the activate command is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Activation for card XXXX Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Activation for card XXXX Completed.
;
```
Issue command to allow the standby MASP to load.
ALW-CARD:LOC=XXXX
(Where XXXX is the location of the standby MASP used in the previous command)

Response to allow-card command is shown.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    Card has been allowed.
;
```

Issue command to report the status of the Standby MASP.

REPT-STAT-CARD:lOC=XXXX

Response from the retrieve command is displayed.

Verify that Standby MASP card running is running BLMCAP flash GPL.

eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE      GPL        PST            SST        AST
    XXXX   XXX-XXX-XXX  E5MCAP    OAMHC      IS-NR          Standby    -----
      ALARM STATUS        = No Alarms.
      BLMCAP  GPL version = YYY-YYY-YYY
      IMT BUS A           = Conn
      IMT BUS B           = Conn
      CURRENT TEMPERATURE =  33C ( 92F)
      PEAK TEMPERATURE:   =  33C ( 92F)     [17-10-14 00:30]

    Command Completed.
;

If this is the first pass through this procedure, issue command to boot the active MASP. Otherwise, go to Step 15.
INIT-CARD:LOC=YYYY
(Where YYYY is the location of the active MASP.)

Response to card initialization is shown.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 
    Init Card command issued to card YYYYY
;
```
Issue the command to log back in to the system.
LOGIN:UID=XXXXXX
(Where XXXXXX is a valid login ID)

Response to login command is displayed.

Ignore any login failure message.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y 
        User logged in on terminal UU.
;

? Login failures since last successful LOGIN
Last successful LOGIN was on port ? on ??-??-?? @ ??:??:?? 
```
Echo command input to capture terminal.
ACT-ECHO:TRM=P
(Where P is the terminal port number specified in Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 3)

Response to print capture command is displayed.

Repeat Steps 1 – 11 for the formerly active MASP.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y 
    Scroll Area Output will be echoed to Port P.
;
```
Issue the command to display the cards running with BLDC32 flash GPL
REPT-STAT-GPL:GPL=BLDC32
Response from the GPL status command is displayed.

Verify that no cards are displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y
    GPL Auditing  ON

    GPL        CARD      RUNNING            APPROVED      TRIAL

    Command Completed.
;
```

Recovery Procedure A

Perform this Recovery Procedure in order to copy the BLMCAP GPLs from the source after performing procedures Full Fallback Using Spare E5-MASP, Full Fallback Using Fixed Disk As OAM Conversion Workspace – Case 1, Full Fallback Using Fixed Disk As OAM Conversion Workspace – Case 2, and Full Fallback Using Fixed Disk As OAM Conversion Workspace – Case 3 when upgrading with the fixed workspace.

Note:

If the source release is 46.5 or prior, perform this procedure only when the MASPs are running the BLMCAP flash image. Otherwise Procedures Revert IPS (ENET-B) cards on VxWorks6.4 - Revert the MASP Card to VxWorks6.4 must be performed before this procedure.

SHOULD THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.

When directed to by My Oracle Support, execute this procedure: After the completion of Full Fallback Using Spare E5-MASP, Full Fallback Using Fixed Disk As OAM Conversion Workspace – Case 1, Full Fallback Using Fixed Disk As OAM Conversion Workspace – Case 2, Full Fallback Using Fixed Disk As OAM Conversion Workspace – Case 3 (but not Fall Back Procedure for Network Cards).

If a USB drive is present in the system, remove it.
If recovering from release 46.3 or later back to a release of 46.2 or earlier, go to step 16, else continue to next step.
Insert pre-upgrade source release media into the active MASP.
Once inserted, allow time for the source-release RMD to be detected by the system.

Issue the command to retrieve BLMCAP application data.

rtrv-gpl:gpl=blmcap

Response to rtrv-gpl command is displayed.

Record the REMOVE TRIAL version:

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y
    GPL Auditing  ON

    GPL       CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
    BLMCAP    1114  xxx-xxx-xxx  xxx-xxx-xxx      yyy-yyy-yyy  -----------
    BLMCAP    1116  xxx-xxx-xxx  xxx-xxx-xxx      yyy-yyy-yyy  xxx-xxx-xxx
;

Issue the command to change the gpl.

chg-gpl:gpl=blmcap:ver=xxx-xxx-xxx

(Where xxx-xxx-xxx is the GPL version recorded in the previous step)

Response to chg-gpl command is displayed.


    eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y
    BLMCAP upload to 1116 completed
    BLMCAP upload to 1114 completed
    System Release ID table upload to 1116 completed
    System Release ID table upload to 1114 completed
;

Issue the report card status command.
rept-stat-card:appl=oam
Response to the card status command is displayed.

Record which MASP is Active and Standby.

Record the card locations of the MASPs:

Act MASP ________

Stby MASP _______

Note:
The Standby MASP may report IS-ANR (and the Standby TDM may report 00S-MT|Isolated.) If so, check LEDs on the card. If LEDs are green, it is OK to proceed. This condition will clear after step 21.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE    GPL        PST            SST        AST
    1113    XXX-XXX-XXX E5MCAP  OAMHC      IS-NR          Active     -----
    1115    XXX-XXX-XXX E5MCAP  OAMHC      IS-NR          Standby    -----
    Command Completed.
;
```
Remove the source-release RMD from the drive slot.
Store RMD in a safe place.
Repeat step 8 until the standby location is IS-NR in step 9.
Force a switchover by issuing initialize-card command.
init-card:loc=YYYY
Where YYYY is the active MASP location recorded in step 9.
Issue the command to log in to the system.
login:uid=XXXXXX
(Where XXXXXX is a valid login ID)

Response to login command is displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
User logged in on terminal X
```

Issue the command to initialize both MASP cards.

init-card:appl=oam

Response to initialize command is displayed.

Ensure that the release shown in the banner is the source release after the MASP becomes active again.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
*   0261.0013  * CARD 111X OAMHC       Card is isolated from the system
                 ASSY SN: xxxxxxxx
;

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    5001.0009    CARD 111X OAMHC       MASP became active
;
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    5038.0014    CARD XXXX OAMHC        Card is present
                 ASSY SN: xxxxxxxx
;

Continue to Recovery Procedure C if directed by the My Oracle Support. Otherwise verify the system with the EAGLE health check References.

Note:
Command REPT-STAT-GPL:DISPLAY=ALL can be used to verify this step.

Recovery Procedure B

Full Fallback Using Spare E5-MASP

Perform the recovery procedure if directed to do so by My Oracle Support when failure occurs in STP Conversion, Step 1, Item C through Migrate the MCPM Cards Running VxWorks 6.4 GPL to VxWorks 6.9 GPL.

This procedure is a full fallback to the source-release on the spare E5-MASP.

Note:

If the source release is 46.5 or prior, perform this procedure only when the MASPs are running the BLMCAP flash image. Otherwise Revert IPS (ENET-B) cards on VxWorks6.4 - Revert the MASP Card to VxWorks6.4 must be performed before this procedure.

SHOULD THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.

When directed to by My Oracle Support, execute this procedure.

If upgrade using the fixed disk method, use Full Fallback Using Fixed Disk As OAM Conversion Workspace – Case 1.
Only perform this procedure if directed by My Oracle Support
Issue the report card status command.
rept-stat-card:appl=oam
Response to the card status command is displayed.

Determine MASP activity. Record which MASP is Active and Standby.

Record the card locations of both sets of MASPs:

Act MASP ________

Stby MASP ________

For this sample output, 1113 is active and 1115 is standby.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE    GPL        PST            SST        AST
    1113    XXX-XXX-XXX E5MCAP  OAMHC      IS-NR          Active     -----
    1115    XXX-XXX-XXX E5MCAP  OAMHC      IS-NR          Standby    -----
;
```
Remove USB drive from system if present.
Place spare E5-MASP in system.
Slide the MASP H/S switch (SW3) on the standby MASP up to the unlocked position (Wait for all drive LEDs to transition to a steady blue).
Remove the standby E5-MASP card determined in step 2.

Insert the spare E5-MASP card.

Slide the MASP H/S switch (SW3) on the new standby MASP down to the locked position (Wait for the MASP H/S LED to transition from blinking blue to off and the MASP to come up in standby mode).

Note:
UAMs are generated during this step. An audible alarm is generated. Wait for the new standby E5-MASP to come up in standby mode and system returns to duplex mode.
Insert the source-release media into the system.
A source-release USB drive in the active E5-MASP.
Once inserted, allow time for the source-release RMD to be detected by the system

After the standby MASP is available, issue the command to initialize the active MASP.

init-card:loc=XXXX

(Where XXXX is the location of the ACTIVE MASP slot)

Response to command is displayed.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    init-card:loc=XXXX
    Command entered at terminal #10.
;
    eaglestp 99-01-02 08:28:34 EST Rel XX.x.x-XX.x.x
*   0261.0013  * CARD XXXX OAMHC       Card is isolated from the system
                 ASSY SN: xxxxxxxx
;
    5038.0014    CARD XXXX OAMHC       Card is present
                 ASSY SN: xxxxxxxx
;

Issue the command to log in to the system.
login:uid=XXXXXX
(Where XXXXXX is a valid login ID)

Response to login command is displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    User logged in on terminal X
```

Inhibit the standby MASP.

inh-card:loc=XXXX

(Where XXXX is location of standby MASP)

Response to the command is displayed.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been inhibited.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;

Put the E5-MASP system in simplex mode.
Slide the MASP H/S switch (SW3) on the standby MASP up to the unlocked position (Wait for all drive LEDs to transition to a steady blue).
Init-card:loc=XXXX

(Where XXXX is the location of the ACTIVE MASP slot)

Wait for the active OAM to return to service and enter simplex mode.

Issue the retrieve GPL command to verify source-release GPLs.

rtrv-gpl

Response to the retrieve command is displayed.

Verify that the GPL versions in REMOVE TRIAL column and RELEASE column match those in Software Release Numbering for Source- Release GPLs.

Example here has location 1114 as the Active MASP slot.

eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y 
    GPL Auditing  OFF

    APPL      CARD  RELEASE      APPROVED         TRIAL        REMOVE TRIAL
    SS7ANSI   1114  XXX-XXX-XXX  XXX-XXX-XXX      XXX-XXX-XXX  XXX-XXX-XXX
    SS7ANSI   1116  -----------  -----------      -----------  -----------
    ATMANSI   1114  XXX-XXX-XXX  XXX-XXX-XXX      XXX-XXX-XXX  XXX-XXX-XXX
    ATMANSI   1116  -----------  -----------      -----------  -----------
    CCS7ITU   1114  XXX-XXX-XXX  XXX-XXX-XXX      XXX-XXX-XXX  XXX-XXX-XXX
    CCS7ITU   1116  -----------  -----------      -----------  -----------
    SS7GX25   1114  XXX-XXX-XXX  XXX-XXX-XXX      XXX-XXX-XXX  XXX-XXX-XXX
    SS7GX25   1116  -----------  -----------      -----------  -----------
    IMT       1114  XXX-XXX-XXX  XXX-XXX-XXX      XXX-XXX-XXX  XXX-XXX-XXX
    IMT       1116  -----------  -----------      -----------  -----------
    BPHCAP    1114  XXX-XXX-XXX  XXX-XXX-XXX      XXX-XXX-XXX  XXX-XXX-XXX
    BPHCAP    1116  -----------  -----------      -----------  -----------
;

Issue the command to retrieve measurement setup.

rtrv-meas-sched

Response to retrieve command is displayed.

Record if collection is on or off:

___________

If COLLECT=ON, continue to next step. Otherwise, go to Step 20.

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    COLLECT        = off
    SYSTOT-STP     = (off)
    SYSTOT-TT      = (off)
    COMP-LNKSET    = (off)
    COMP-LINK      = (off)
    MTCD-STP       = (on)
    MTCD-LINK      = (on)
    MTCD-LNKSET    = (on)
;

Issue the command to turn off measurement collection.
Note:
If executed, this step causes the database level to increment.
chg-meas:collect=off
Response to the change command is displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    chg-meas:collect=off
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    CHG-MEAS: MASP A – COMPLTD
;
```

Inhibit the standby MASP.

inh-card:loc=XXXX

(Where XXXX is location of standby MASP)

Response to the command is displayed.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been inhibited.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;

Bring the standby E5-MASP system back on the bus.
Slide the E5-MASP H/S switch (SW3) on the standby MASP down to the locked position (Wait for E5MASP H/S LED to transition from blinking blue to a steady blue and the card to return to the IMT bus.)
Issue the command to initialize the flash memory.
init-flash:code=appr:loc=XXXX
Where XXXX is the location for the Standby MASP.

Response to the init flash command is displayed.

Wait for the downloading to complete.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card xxxx started.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card xxxx completed.
;
```

Issue the command to activate the flash on the standby MASP.

act-flash:loc=XXXX

(Where XXXX is the location for the Standby MASP.)

Response to the activate command is displayed.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    act-flash:loc=XXXX
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Activation for card XXXX Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Activation for card XXXX Completed.
;

Issue the command to allow card.

alw-card:loc=XXXX

Where XXXX is the location for the Standby MASP.

Response to the command is displayed.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been allowed.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;

Issue the report card status command.

rept-stat-card:appl=oam

Response from the retrieve command is displayed.

Verify that the standby MASP is running the upgrade source release GPL.

eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    CARD   VERSION     TYPE    APPL       PST           SST        AST
    1113   XXX-XXX-XXX E5MCAP  OAMHC      IS-NR         Active     -----
    1115   XXX-XXX-XXX E5MCAP  OAMHC      IS-NR         Standby    -----
    Command Completed.
;

Issue the command to display security log status.

rept-stat-seculog

Response to the command is displayed.

If the ENTRIES column displays any value other than 0 for the Standby ROLE, proceed to the next step. Otherwise, go to step 24.

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    rept-stat-seculog
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
                 -- SINCE LAST UPLOAD --  OLDEST   NEWEST   LAST
    LOC  ROLE    ENTRIES %FULL OFLO FAIL  RECORD   RECORD   UPLOAD
    1114 Active  19      1     No   No    99-01-01 99-01-01 00-00-00
                                          13:43:37 14:08:12 00:00:00
    1116 Standby 0       0     No   No    99-01-01 99-01-01 99-01-01 
                                          13:39:39 13:43:10 14:07:59
;

Issue the command to copy the security log from the standby disk.
copy-seculog:slog=stb:dfile=upg.procC
Response to the copy security log command is displayed.

If this command fails, proceed to next step. Otherwise, go to Step 24.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    Security log on TDM 111X copied to file upg28.procC on TDM 111Y
;

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    0468.0177    SECULOG 111X          Security log exception cleared
;
```

Issue the command to display the FTA directory.

disp-fta-dir

Response to the command is displayed.

If there are any files that need to be saved, they need to be removed via a file transfer.

eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    File Transfer Area Directory of fixed disk 1114

    FILENAME                         LENGTH   LAST MODIFIED     LBA
    YYMMDDs.log                      2560256  99-01-03 10:18:44 388769
    YYMMDDa.log                      2560256  99-01-03 10:19:20 393770
    m60_lnp.csv                      0        99-01-03 13:10:38 398771
      3 File(s) 21093376 bytes free
;

Issue the command to delete ALL files in the transfer area.
dlt-fta:all=yes
Response to the delete command is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    dlt-fta:all=yes:loc=XXXX
    Command entered at terminal #nn.
;
```
Repeat Steps 19-20.

Issue the command to copy to the standby disk.

copy-disk:dloc=XXXX:force=yes:format=yes

(Where XXXX is the location of the STANDBY TDM)

Response to the copy-disk command is displayed.

Wait for the card reload to complete.

If this is the second time performing this step, go to Step 30. Otherwise continue.

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    Copy-disk (fixed): from active (YYYY) to standby (XXXX) started.
    Extended processing required, please wait.
;

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    Copy-disk (fixed): from active (XXXX) to standby (XXXX) complete.
    Measurements may be allowed now if desired.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    0485.0014    CARD 1115 OAMHC       Card is present
;

Issue the command to display card status.

rept-stat-card

Response to the card status command is displayed.

Verify that the GPL versions that are displayed in the VERSION column are correct; see Software Release Numbering.

Record the location of the Standby MASP:

MASP ___________

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    rept-stat-card
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y 
    CARD   VERSION      TYPE    APPL       EST            SST        AST
    1101   XXX-XXX-XXX  DSM     SCCPHC     IS-NR          Active     -----
    1102   XXX-XXX-XXX  DSM     SCCPHC     IS-NR          Active     -----
    1103   XXX-XXX-XXX  TSM     GLSHC      IS-NR          Active     -----
    1104   XXX-XXX-XXX  TSM     GLSHC      IS-NR          Active     -----
    1105   XXX-XXX-XXX  LIMDS0  SS7ML      IS-NR          Active     -----
    1111   XXX-XXX-XXX  IPSM    IPSHC      IS-NR          Active     -----
    1113   XXX-XXX-XXX  E5MCAP  OAMHC      IS-NR          Active     -----
    1114   -----------  E5TDM   -------    IS-NR          Active     -----
    1115   XXX-XXX-XXX  E5MCAP  OAMHC      IS-NR          Standby    -----
    1116   -----------  E5TDM   -------    IS-NR          Active     -----
    1117   -----------  E5MDAL  -------    IS-NR          Active     -----
    1201   XXX-XXX-XXX  LIMDS0  SS7ML      IS-NR          Active     -----
    1202   XXX-XXX-XXX  LIMDS0  SS7ML      IS-NR          Active     -----
    1203   XXX-XXX-XXX  DCM     IPLHC      IS-NR          Active     -----
    1204   XXX-XXX-XXX  DCM     IPLHC      IS-NR          Active     -----
    1211   XXX-XXX-XXX  DCM     IPGHC      IS-NR          Active     -----
    1218   XXX-XXX-XXX  TSM     GLSHC      IS-NR          Active     -----
    Command Completed.
;

Inhibit the standby MASP.

inh-card:loc=XXXX

(Where XXXX is location of standby MASP)

Response to the command is displayed.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been inhibited.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;

Replace the standby E5-MASP with the E5-MASP removed in step 4.
Slide the MASP H/S switch (SW3) on the standby MASP up to the unlocked position (Wait for all drive LEDs to transition to a steady blue).
Remove the standby E5-MASP card.

Insert the spare E5-MASP card.

Slide the MASP H/S switch (SW3) on the new standby MASP down to the locked position (Wait for the MASP H/S LED to transition from blinking blue to off and the MASP to come up in standby mode).

Note:
UAMs are generated during this step. An audible alarm is generated. Wait for the new standby E5-MASP to come up in standby mode and system returns to duplex mode.
Insert the source-release media into the system.
Insert an USB drive in the standby E5-MCAPs.
Once inserted, allow time for the source-release RMD to be detected by the system
Repeat steps 15 - 24.
After completing Step 24 the second time, continue to Step 30.
If steps 12 was executed, issue the command to turn the measurements collection on.
chg-meas:collect=on
Response to change measurement command is displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y 
    chg-meas:collect=on
    Command entered at terminal #10.
;

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    CHG-MEAS: MASP A - COMPLTD
;
```
Execute Procedure 17.
If this completes the recovery as directed by My Oracle Support, verify the system with the EAGLE health check in References. Otherwise continue with Recovery Procedure C.
If failure occurred prior to entering Phase 3, recovery is complete.

Full Fallback Using Fixed Disk As OAM Conversion Workspace – Case 1

Perform the recovery procedure if directed to do so by My Oracle Support when failure occurs in Verifying the Target Release and Software Access Key through STP Conversion, Step 1.

Note:

this procedure is done in lieu of Backing Up Fixed Disk for the case where a removable disk was NOT used as the workspace for the OAM conversion.

Note:

If the source release is 46.5 or prior, perform this procedure only when the MASPs are running the BLMCAP flash image. Otherwise Revert IPS (ENET-B) cards on VxWorks6.4 to Revert the MASP Card to VxWorks6.4 must be performed before this procedure.

SHOULD THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.

When directed to by My Oracle Support, execute this procedure:

If failure occurred between Verifying the Target Release and Software Access Key and STP Conversion, Step 1, Table: Act Upgrade Command Actions, Item E.

Only perform this procedure if directed by My Oracle Support.
If present, remove the target-release media from the system.

Issue the command to initialize both MASP cards.

init-card:appl=oam

Response to initialize command is displayed.

Ensure that the release shown in the banner is the source release after the MASP becomes active again.


    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 
*   0261.0013  * CARD 111X OAMHC       Card is isolated from the system
                 ASSY SN: xxxxxxxx
;

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    5001.0009    CARD 111X OAMHC       MASP became active
;
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    5038.0014    CARD XXXX OAMHC       Card is present
                 ASSY SN: xxxxxxxx
;

Execute Recovery Procedure A.

Full Fallback Using Fixed Disk As OAM Conversion Workspace – Case 2

Perform this recovery procedure if directed to do so by My Oracle Support when failure occurred between STP Conversion, Step 1, Item F through Item I. . This procedure makes the partition with the source GPLs active on both TDMs.

Note:

SHOULD THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.

When directed to by My Oracle Support, execute this procedure:

If failure occurred between STP Conversion, Step 1, Table: Act Upgrade Command Actions, Item F and STP Conversion, Step 1, Table: Act Upgrade Command Actions, Item I.

Remove USB drive from system if present.

Issue the command to display database status during upgrades.

act-upgrade:action=dbstatus

Response to the command is displayed.

Look at the status field and determine the loc of the TDM marked UPG 2.

eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y Upg Phase X 
;    DATABASE STATUS: >> NOT OK (DMS) <<
           TDM 1114 ( STDBY)                 TDM 1116 ( ACTV )
            C   LEVEL    TIME LAST BACKUP     C   LEVEL    TIME LAST BACKUP
            - -------- ---------------------- - -------- ----------------------
    FD BKUP Y   nnnnnn     -        -         Y   nnnnnn YY-MM-DD hh:mm:ss zzz
    FD CRNT Y   nnnnnn                        Y   nnnnnn
            MCAP 1113                         MCAP 1115
            - --------                        - --------
    RD BKUP -    -         -        -         -    -         -        -
    USB BKP -    -         -        -         -    -         -        -

    CARD/APPL  LOC   C  T  LEVEL       TIME LAST UPDATE   VERSION STATUS
    ---------  ----  -  -  ----------  -----------------  -------------------
    OAM-RMV    1113  -  -      -           -        -          -
    TDM-CRNT   1114  Y  N  nnnnnn      YY-MM-DD hh:mm:ss  ZZZ-ZZZ-ZZZ  UPG 2
    TDM-BKUP   1114  Y  -  nnnnnn      YY-MM-DD hh:mm:ss  ZZZ-ZZZ-ZZZ  UPG 2
    OAM-RMV    1115  -  -      -           -        -          -
    OAM-USB    1115  -  -      -           -        -          -
    TDM-CRNT   1116  Y  N  nnnnnn      YY-MM-DD hh:mm:ss  XXX-XXX-XXX  NORMAL
    TDM-BKUP   1116  Y  -  nnnnnn      YY-MM-DD hh:mm:ss  XXX-XXX-XXX  NORMAL

    INACTIVE PARTITION GROUP
    CARD/APPL  LOC   C  T  LEVEL       TIME LAST UPDATE   VERSION STATUS
    ---------  ----  -  -  ----------  -----------------  -------------------
    TDM-CRNT   1114  Y  -  nnnnnn      YY-MM-DD hh:mm:ss  XXX-XXX-XXX  NORMAL
    TDM-BKUP   1114  Y  -  nnnnnn      YY-MM-DD hh:mm:ss  XXX-XXX-XXX  NORMAL
    TDM-CRNT   1116  N  -  1           00-00-00 00:00:00  ZZZ-ZZZ-ZZZ  NORMAL
    TDM-BKUP   1116  N  -  1           00-00-00 00:00:00  ZZZ-ZZZ-ZZZ  NORMAL

If the TDM marked in UPG 2 is the active MASP continue. Otherwise, go to step 6.

Issue the command to init active location.

init-card:loc=YYYY

(Where YYYY is location of active MASP)

Response to initialize command is displayed.

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
*   0261.0013  * CARD XXXX OAMHC       Card is isolated from the system
                 ASSY SN:  xxxxxxxx
; 
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    5038.0014    CARD XXXX OAMHC       Card is present
                 ASSY SN: xxxxxxxx
;

Issue the command to log back in to the system.
login:uid=XXXXXX
(Where XXXXXX is a valid login ID)

Response to login command is displayed.

Ignore any login failure message.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
        User logged in on terminal 10.
;

? Login failures since last successful LOGIN
Last successful LOGIN was on port ? on ??-??-?? @ ??:??:?? 
```

Issue the command to display active/inactive disk partitions.

send-msg:ds=1:da=h’5d:f=h’47:loc=YYYY

(Where YYYY is location of active MASP)

Response to command.

Note:

Look for the command response on a terminal with all output display groups set to yes (printer/ksr terminal port specified in, Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 6)

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upgrade Phase x
    System Buffer sent has following attributes :
        Msg Length = H’0010
        Dest Card = H’00fb
        Orig Subsys = H’0001            Dest Subsys = H’0001
        Orig Appl ID = H’0030           Dest Appl ID = H’005d
        Func ID = H’0047                Bus/Ret/Sut = H’0002
        Violation Ind = H’0000
    User Message sent to location YYYY.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upgrade Phase x
    ACTIVE OAM Partition Grp Info:
    num_group = 2              
    num_partitions_per_group = 2
    active_partitions[]   = 0    1
    inactive_partitions[] = 2    3
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upgrade Phase x
    STANDBY OAM Partition Grp Info:
    num_group = 2              
    num_partitions_per_group = 2
    active_partitions[]   = 2    3
    inactive_partitions[] = 0    1
;

Issue the command to swap active/inactive disk partitions.

send-msg:ds=1:da=h’5d:f=h’48:loc=YYYY

(Where YYYY is location of active MASP)

Response to command.

Note:

Look for the command response on a terminal with all output display groups set to yes (printer/ksr terminal port specified in Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 6)

Compare the values for the active_partitions and inactive_partitions with those in step 6. For the STANDBY OAM, the values for the active_partitions shown should equal those for the inactive_partitions shown in step 6, and vice-versa. For the ACTIVE OAM, both sets of values should be identical.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    System Buffer sent has following attributes :
        Msg Length = H’0010
        Dest Card = H’00fb
        Orig Subsys = H’0001            Dest Subsys = H’0001
        Orig Appl ID = H’0030           Dest Appl ID = H’005d
        Func ID = H’0048                Bus/Ret/Sut = H’0002
        Violation Ind = H’0000
    User Message sent to location YYYY.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Partition switch PASSED
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    ACTIVE OAM Partition Grp Info:
    num_group = 2
    num_partitions_per_group = 2
    active_partitions[]   = 0    1
    inactive_partitions[] = 2    3
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    STANDBY OAM Partition Grp Info:
    num_group = 2              
    num_partitions_per_group = 2
    active_partitions[]   = 0    1
    inactive_partitions[] = 2    3
;

Inhibit the standby MASP.
inh-card:loc=XXXX
(Where XXXX is the location for the Standby MASP.)

Response to the inhibit command is displayed

Verify UAM 514 is displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    Card is inhibited.
;

   eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase x
   **  5045.0514 ** CARD XXXX OAMHC         Standby MASP is inhibited
;
```
Note:
Wait for the card to boot and return to the IMT bus.
Issue the command to initialize the flash memory on the standby MASP.
Note:
The approved flash GPL is the source version.
init-flash:code=appr:loc=XXXX
(Where XXXX is the location for the Standby MASP.)

Response to flash initialization is shown.

Verify UAM 0004 is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card xxxx started.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card xxxx completed.
; 
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
*   8003.0004  * GPL SYSTEM BLMCAP       Card is running non-activated GPL
;
```
Note:
Wait for card to boot and return to the IMT bus.

Issue the command to activate the flash on the standby MASP.

act-flash:loc=XXXX

(Where XXXX is the location for the Standby MASP.)

Response to the activate command is displayed.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    act-flash:loc=XXXX
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Activation for card XXXX Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Activation for card XXXX Completed.
;

Issue the command to allow card.
alw-card:loc=XXXX
(Where XXXX is the location for the Standby MASP.)

Response to the command is displayed.
```
      eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been allowed.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;
```
Determine the status of the GPLs running on the card location.
rept-stat-gpl:loc=XXXX
(Where XXXX is the location for the Standby MASP.)

Response from the status command is displayed.

Verify the standby MASP is running the upgrade source release GPLs. Verify that no “ALM” indicator is displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    GPL Auditing  ON

    GPL        CARD      RUNNING            APPROVED      TRIAL
    OAMHC      1115      134-074-000        -----------   -----------
          BLMCAP         134-070-000       134-070-000   134-070-000

    Command Completed.
;
```

If the active MASP is not running the upgrade source release GPL continue. Otherwise go to step 20.

init-card:loc=XXXX

(Where XXXX is location of active MASP)

Response to initialize command is displayed.

        eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
*   0261.0013  * CARD XXXX OAMHC       Card is isolated from the system
                 ASSY SN:  xxxxxxxx
; 
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    5038.0014    CARD XXXX OAMHC       Card is present
                 ASSY SN: xxxxxxxx
;

Issue the command to log back in to the system.
login:uid=XXXXXX
(Where XXXXXX is a valid login ID)

Response to login command is displayed.

Ignore any login failure message.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y 
        User logged in on terminal 10.
;

? Login failures since last successful LOGIN
Last successful LOGIN was on port ? on ??-??-?? @ ??:??:?? 
```
Inhibit the standby MASP.
inh-card:loc=XXXX
(Where XXXX is the location for the Standby MASP.)

Response to the inhibit command is displayed

Verify UAM 514 is displayed.
```
       eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    Card is inhibited.
;

   eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase x
   **  5045.0514 ** CARD XXXX OAMHC         Standby MASP is inhibited
;
```
Note:
Wait for the card to boot and return to the IMT bus.

Issue the command to initialize the flash memory on the standby MASP.

init-flash:code=appr:loc=XXXX

(Where XXXX is the location for the Standby MASP.)

Response to flash initialization is shown.

Verify UAM 0004 is displayed.

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card xxxx started.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card xxxx completed.
; 
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
*   8003.0004  * GPL SYSTEM BLMCAP       Card is running non-activated GPL
;

Note:

Wait for card to boot and return to the IMT bus.

Issue the command to activate the flash on the standby MASP.

act-flash:loc=XXXX

(Where XXXX is the location for the Standby MASP.)

Response to the activate command is displayed.

       eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    act-flash:loc=XXXX
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Activation for card XXXX Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Activation for card XXXX Completed.
;

Issue the command to allow card.
alw-card:loc=XXXX
(Where XXXX is the location for the Standby MASP.)

Response to the command is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been allowed.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;
```
Determine the status of the GPLs running on the card location.
rept-stat-gpl:loc=XXXX
(Where XXXX is the location for the Standby MASP.)

Response from the status command is displayed.

Verify that the standby MASP is running the upgrade source release GPLs. Verify that no ALM indicator is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    GPL Auditing  ON

    GPL        CARD      RUNNING            APPROVED      TRIAL
    OAMHC      1115      134-074-000        -----------   -----------
          BLMCAP         134-070-000       134-070-000   134-070-000

    Command Completed.
;
```
Execute Recovery Procedure A.

Full Fallback Using Fixed Disk As OAM Conversion Workspace – Case 3

Perform this recovery procedure if directed to do so by My Oracle Support when failure occurred between STP Conversion, Step 1 and Completing Upgrade/Return to Full-Function Mode [End of Session 1] This procedure makes the partition with the source GPLs active on both TDMs.

Note:

If the database level in the target release is different from the last database level of the source release, this procedure CANNOT BE USED; contact My Oracle Support.

Note:

SHOULD THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.

When directed to by My Oracle Support, execute this procedure:

If failure occurred between STP Conversion, Step 1 and Migrate the MCPM Cards Running VxWorks 6.4 GPL to VxWorks 6.9 GPL [End of Session 1].

If this is an incremental upgrade (i.e. the SOURCE release equals the TARGET release, go to Verifying All Databases, Step 1.
Complete all steps from Verifying All Databases to the end of Session 1 (Migrate the MCPM Cards Running VxWorks 6.4 GPL to VxWorks 6.9 GPL).

Note:
When executing Verifying All Databases through Migrate the MCPM Cards Running VxWorks 6.4 GPL to VxWorks 6.9 GPL in the recovery scenario, the terminology of source and target are reversed. Target release becomes the software load that is being recovered to (45.0.0) and the source release becomes the software load that was upgraded to (45.0.1).
Remove USB drive from system if present.

Issue the command to display active/inactive disk partitions.

send-msg:ds=1:da=h’5d:f=h’47:loc=YYYY

(Where YYYY is location of active MASP)

Response to command.

Note:

Look for the command response on a terminal with all output display groups set to yes (printer\ksr terminal port specified in Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 6)

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upgrade Phase x
    System Buffer sent has following attributes :
        Msg Length = H’0010
        Dest Card = H’00fb
        Orig Subsys = H’0001            Dest Subsys = H’0001
        Orig Appl ID = H’0030           Dest Appl ID = H’005d
        Func ID = H’0047                Bus/Ret/Sut = H’0002
        Violation Ind = H’0000
    User Message sent to location XXXX.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upgrade Phase x
    ACTIVE OAM Partition Grp Info:
    num_group = 2              
    num_partitions_per_group = 2
    active_partitions[]   = 2    3
    inactive_partitions[] = 0    1
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upgrade Phase x
    STANDBY OAM Partition Grp Info:
    num_group = 2              
    num_partitions_per_group = 2
    active_partitions[]   = 2    3
    inactive_partitions[] = 0    1
;

Issue the command to swap active/inactive disk partitions.

send-msg:ds=1:da=h’5d:f=h’48:loc=YYYY

(Where YYYY is location of active MASP)

Response to command.

Note:

Look for the command response on a terminal with all output display groups set to yes (printer\ksr terminal port specified in Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 6)

Compare the values for the active_partitions and inactive_partitions with those in step 3. For the STANDBY OAM, the values for the active_partitions shown should equal those for the inactive_partitions shown in step 3, and vice-versa. For the ACTIVE OAM, both sets of values should be identical.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    System Buffer sent has following attributes :
        Msg Length = H’0010
        Dest Card = H’00fb
        Orig Subsys = H’0001            Dest Subsys = H’0001
        Orig Appl ID = H’0030           Dest Appl ID = H’005d
        Func ID = H’0048                Bus/Ret/Sut = H’0002
        Violation Ind = H’0000
    User Message sent to location XXXX.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Partition switch PASSED
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    ACTIVE OAM Partition Grp Info:
    num_group = 2              
    num_partitions_per_group = 2
    active_partitions[]   = 2    3
    inactive_partitions[] = 0    1
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    STANDBY OAM Partition Grp Info:
    num_group = 2              
    num_partitions_per_group = 2
    active_partitions[]   = 0    1
    inactive_partitions[] = 2    3
;

Inhibit the standby MASP.
inh-card:loc=XXXX
(Where XXXX is the location for the Standby MASP.)

Response to the inhibit command is displayed

Verify UAM 514 is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    Card is inhibited.
;

   eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase x
   **  5045.0514 ** CARD XXXX OAMHC         Standby MASP is inhibited
;
```
Note:
Wait for the card to boot and return to the IMT bus.
Issue the command to initialize the flash memory on the standby MASP.
init-flash:code=trial:loc=XXXX
(Where XXXX is the location for the Standby MASP.)

Response to flash initialization is shown.

Verify UAM 0004 is displayed.
```
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card xxxx started.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card xxxx completed.
; 
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
*   8003.0004  * GPL SYSTEM BLMCAP       Card is running non-activated GPL
;
```
Note:
Wait for card to boot and return to the IMT bus.

Issue the command to activate the flash on the standby MASP.

act-flash:loc=XXXX

(Where XXXX is the location for the Standby MASP.)

Response to the activate command is displayed.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    act-flash:loc=XXXX
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Activation for card XXXX Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Activation for card XXXX Completed.
;

Issue the command to allow card.

alw-card:loc=XXXX

(Where XXXX is the location for the Standby MASP.)

Response to the command is displayed.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been allowed.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;

Determine the status of the GPLs running on the card location.

rept-stat-gpl:loc=XXXX

(Where XXXX is the location for the Standby MASP.)

Response from the status command is displayed.

Verify that the standby MASP is running the upgrade source release GPLs.

    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y 
    GPL Auditing  ON

    GPL        CARD      RUNNING            APPROVED      TRIAL
    OAMHC69    XXXX      XXX-XXX-XXX        -----------   -----------
          BLDC32         XXX-XXX-XXX        YYY-YYY-YYY   XXX-XXX-XXX

    Command Completed.
;

Issue the command to init active location.

init-card:loc=YYYY

(Where YYYY is location of active MASP)

Response to initialize command is displayed.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
*   0261.0013  * CARD XXXX OAMHC      Card is isolated from the system
                 ASSY SN:  xxxxxxxx
; 
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    5038.0014    CARD XXXX OAMHC      Card is present
                 ASSY SN: xxxxxxxx
;

Issue the command to log back in to the system.

login:uid=XXXXXX

(Where XXXXXX is a valid login ID)

Response to login command is displayed.

Ignore any login failure message.

    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
        User logged in on terminal nn.
;

? Login failures since last successful LOGIN
Last successful LOGIN was on port ? on ??-??-?? @ ??:??:??

Issue the command to display active/inactive disk partitions.

send-msg:ds=1:da=h’5d:f=h’47:loc=XXXX

(Where XXXX is location of newly active MASP)

Response to command.

Note:

Look for the command response on a terminal with all output display groups set to yes (printer\ksr terminal port specified in Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 6)

If the standby partition information is not displayed, wait for the standby MASP to return to service and repeat step 11.

Command Accepted - Processing
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y Upgrade Phase x
    System Buffer sent has following attributes :
        Msg Length = H’0010
        Dest Card = H’00fb
        Orig Subsys = H’0001            Dest Subsys = H’0001
        Orig Appl ID = H’0030           Dest Appl ID = H’005d
        Func ID = H’0047                Bus/Ret/Sut = H’0002
        Violation Ind = H’0000
    User Message sent to location YYYY.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y Upgrade Phase x
    ACTIVE OAM Partition Grp Info:
    num_group = 2              
    num_partitions_per_group = 2
    active_partitions[]   = 0    1
    inactive_partitions[] = 2    3
;
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y Upgrade Phase x
    STANDBY OAM Partition Grp Info:
    num_group = 2              
    num_partitions_per_group = 2
    active_partitions[]   = 2    3
    inactive_partitions[] = 0    1
;

Issue the command to swap active/inactive disk partitions.

send-msg:ds=1:da=h’5d:f=h’48:loc=XXXX

(Where XXXX is location of active MASP)

Response to command.

Note:

: Look for the command response on a terminal with all output display groups set to yes (printer\ksr terminal port specified in Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 6)

Compare the values for the active_partitions and inactive_partitions with those in step 12. For the STANDBY OAM, the values for the active_partitions shown should equal those for the inactive_partitions shown in step 12, and vice-versa. For the ACTIVE OAM, both sets of values should be identical.

eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y
    System Buffer sent has following attributes :
        Msg Length = H’0010
        Dest Card = H’00fb
        Orig Subsys = H’0001            Dest Subsys = H’0001
        Orig Appl ID = H’0030           Dest Appl ID = H’005d
        Func ID = H’0048                Bus/Ret/Sut = H’0002
        Violation Ind = H’0000
    User Message sent to location YYYY.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y
    Partition switch PASSED
;
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y 
    ACTIVE OAM Partition Grp Info:
    num_group = 2              
    num_partitions_per_group = 2
    active_partitions[]   = 0    1
    inactive_partitions[] = 2    3
;
    eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y 
    STANDBY OAM Partition Grp Info:
    num_group = 2              
    num_partitions_per_group = 2
    active_partitions[]   = 0    1
    inactive_partitions[] = 2    3
;

Inhibit the standby MASP.
inh-card:loc=YYYY
(Where YYYY is the location for the Standby MASP.)

Response to the inhibit command is displayed

Verify UAM 514 is displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    Card is inhibited.
;

   eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase x
   **  5045.0514 ** CARD XXXX OAMHC         Standby MASP is inhibited
;
```
Note:
Wait for the card to boot and return to the IMT bus.
Issue the command to initialize the flash memory on the standby MASP.
init-flash:code=appr:loc=YYYY
(Where YYYY is the location for the Standby MASP.)

Response to flash initialization is shown.

Verify UAM 0004 is displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card xxxx started.
;
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card xxxx completed.
; 
    eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
*   8003.0004  * GPL SYSTEM BLMCAP       Card is running non-activated GPL
;
```
Note:
Wait for card to boot and return to the IMT bus.

Issue the command to activate the flash on the standby MASP.

act-flash:loc=YYYY

(Where YYYY is the location for the Standby MASP.)

Response to the activate command is displayed.


    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Activation for card XXXX Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Activation for card XXXX Completed.
;

Issue the command to allow card.

alw-card:loc=YYYY

(Where YYYY is the location for the Standby MASP.)

Response to the command is displayed.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been allowed.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;

Determine the status of the GPLs running on the card location.
rept-stat-gpl:loc=XXXX
(Where XXXX is the location for the Standby MASP.)

Response from the retrieve command is displayed.

Verify that the both MASP are running the upgrade source release GPLs. Verify that no “ALM” indicator is displayed
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    GPL Auditing  ON

    GPL        CARD      RUNNING            APPROVED      TRIAL
    OAMHC69    XXXX      XXX-XXX-XXX        -----------   -----------
          BLDC32         XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX

    Command Completed.
;
```
Execute Procedure 15.

Recovery Procedure C

Fall Back Procedure for Network Cards

This procedure captures the card and link status data required when performing a manual fallback of the network cards back to the source-release GPLs.

Issue the command to report card status.

rept-stat-card

Response to the card status command is displayed.

Record all network card applications present for future reference within the procedure.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE      GPL        PST            SST        AST
    1101   XXX-XXX-XXX  DSM       SCCPHC     IS-NR          Active     -----
    1102   XXX-XXX-XXX  DCM       IPLHC      IS-NR          Active     -----
    1103   XXX-XXX-XXX  TSM       GLSHC      IS-NR          Fault      -----
    1105   XXX-XXX-XXX  DCM       IPGHC      IS-NR          Active     -----
    1109   XXX-XXX-XXX  HIPR      HIPR       IS-NR          Active     -----
    1110   XXX-XXX-XXX  HIPR      HIPR       IS-NR          Active     -----
    1111   XXX-XXX-XXX  MCPM      MCPHC      IS-ANR         Active     -----
    1113   XXX-XXX-XXX  E5MCAP    OAMHC      IS-NR          Active     -----
    1114   -----------  E5TDM     -------    IS-NR          Active     -----
    1115   XXX-XXX-XXX  E5MCAP    OAMHC      IS-NR          Standby    -----
    1116   -----------  E5TDM     -------    IS-NR          Active     -----
    1117   -----------  E5MDAL    -------    IS-NR          Active     -----
    1201   XXX-XXX-XXX  LIMT1     SS7HC      IS-NR          Active     -----
    1202   XXX-XXX-XXX  LIMT1     SS7HC      IS-NR          Active     -----
    1209   XXX-XXX-XXX  HIPR2     HIPR2      IS-NR          Active     -----
    1210   XXX-XXX-XXX  HIPR2     HIPR2      IS-NR          Active     -----
    1211   XXX-XXX-XXX  DCM       IPGHC      IS-NR          Active     -----
    1217   XXX-XXX-XXX  TSM       GLSHC      IS-NR          Active     -----
    1218   XXX-XXX-XXX  IPSM      IPSHC      IS-NR          Active     -----
    Command Completed.
;

Issue the card status command.

rept-stat-card:appl=mcp

Response to the card status command is displayed.

If any MCPM cards are displayed, continue to next step. Otherwise, go to Step 4.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE      GPL        PST            SST        AST
    1111   134-064-000  MCPM      MCPHC      IS-NR          Active     -----
    1112   134-064-000  MCPM      MCPHC      IS-NR          Active     -----

    Command Completed.
;

Issue the send message command. Repeat for each MCPM card.
Note:
This command causes the MCPM card to boot with an OBIT indicating a USER INITIATED COLD RESTART. All Measurements data not sent to an FTP server is lost. Waiting for the next scheduled Measurement FTP transfer and use of the rept-ftp-meascommand to save desired measurements can minimize these losses before proceeding with this step.

send-msg:ds=8:da=h’17:f=22:loc=XXXX

(Where XXXX is location of the MCPM cards display in previous step.)

Response to the send message command is displayed.
```
eaglestp YY-MM-DD hh:mm:ss TTTT PPP  XX.x.x.x.x-YY.y.y
    System Buffer sent has following attributes :
        Msg Length = H’0010
        Dest Card = H’00f7
        Orig Subsys = H’0001            Dest Subsys = H’0001
        Orig Appl ID = H’004d           Dest Appl ID = H’001d
        Func ID = H’0016                Bus/Ret/Sut = H’0002
        Violation Ind = H’0000
    User Message sent to location XXXX.

    Command Completed.
;
```
Issue the upgrade activation command.
If the threshold type is set to SET in Verifying all Databases, Step 2 and the source release is 46.0 or higher, issue the following command:
ACT-UPGRADE:ACTION=CONVERTSTP:SRC=FIXED

Otherwise, issue the following command:

ACT-UPGRADE:ACTION=CONVERTSTP:SRC=FIXED:THRES=75

(If another thres value is to be used see recommendation #5 in Recommendations.)

Response to the upgrade command is displayed.

Completion notice of successful upgrade.

If upgrade does not complete successfully, see recommendation # 7 in Recommendations.
```
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3
    Hardware Validation Test Started
    [ASM Obsolescence Test for all applications.]
    [DSM Obsolescence Test for MCP application.]

    Hardware Validation Test Completed Successfully.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3

    Starting network conversion...
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3
    Upgrading MUX card 1109
;
```
Output continues until the following is displayed
```
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3

    Command Complete : Upgrade action completed successfully
;
```
Go to STP Conversion, Step 6.
Complete all steps from STP Conversion, Step 6 to the end of STP Conversion. Then perform Completing Upgrade/Return to Full-Function Mode to complete the roll-back.

Restoring Flash-Based Service Cards

This procedure restores Service Cards that are flash based. This group includes IPSHC, MCPHC, DEIRHC, ENUMHC, SCCPHCand SIPHC cards.

This procedure updates each card with the source release GPLs.

Issue the command to display the GPL status.

rept-stat-gpl:gpl=YYYY

(Where YYYY is one of the Flash-Based service card types listed above.)

Response to the command is displayed.

Record the CARD locations for all cards that have alarms:

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    rept-stat-gpl:gpl=YYYY
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    GPL Auditing  ON

    APPL       CARD      RUNNING            APPROVED      TRIAL
    YYYYY      1101      XXX-XXX-XXX ALM   XXX-XXX-XXX   XXX-XXX-XXX
    YYYYY      1103      XXX-XXX-XXX ALM   XXX-XXX-XXX   XXX-XXX-XXX
Command Completed.
;

Issue the command to inhibit the card if the card is provisioned.
inh-card:loc=XXXX
(Where XXXX is the card location of the cards determined in Step 1)

Response to the inhibit command is displayed.

Wait for the Command completed response before proceeding
```
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been inhibited.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;
```
Issue the command to initialize the flash memory.
flash-card:code=appr:force=yes:loc=XXXX

Note:
this command causes the card to boot.

Response to the flash card command is displayed.

Wait for command complete to indicate that the card is finished loading before proceeding.
```
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    flash-card:code=appr:force=yes:loc=XXXX
    Command entered at terminal #10.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;
```
Issue the command to allow the card if the card is provisioned.
Note:
Specifying the DATA=PERSIST parameter for SCCP application cards allows for warm restart if possible.

alw-card:loc=XXXX

(Where XXXX is the card location of the cards determined in Step 1)

OR

alw-card:loc=XXXX:data=persist

(Where XXXX is the location of an SCCP card determined in Step 1)

Response to the allow command is displayed.

Wait for the card to finish loading before proceeding (approximately 30 seconds).

Note:
If card is MCPM, it may boot with an Obit for Module EMM_MCP.C Class 0001. This is expected behavior and is not service affecting.
```
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    alw-card:loc=1201
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Card has been allowed.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;
```
Repeat Steps 2 – 4 for each card in the current group that has an alarm.
Repeat steps 1 - 5 for each group of cards (VSCCP, ISP, MCP, EROUTE, SCCPHC, IPSHC, ERTHC, and SIPHC)

Issue the command to display the card status.

rept-stat-card

Response to the command is displayed.

Verify that all Flash-Based Service cards are IS-NR and are running the Source-Release GPL versions, as per your reference list of GPLs

For any such card that is not IS-NR or running the correct GPL, repeat Step 2.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    rept-stat-card
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE      GPL        PST            SST        AST
    1101   XXX-XXX-XXX  DSM       VSCCP      IS-NR          Active     -----
    1102   XXX-XXX-XXX  DSM       VSCCP      IS-NR          Active     -----
    1103   XXX-XXX-XXX  TSM       GLSHC      IS-NR          Active     -----
    1104   XXX-XXX-XXX  TSM       GLSHC      IS-NR          Active     -----
    1105   XXX-XXX-XXX  LIMDS0    SS7ML      IS-NR          Active     -----
    1109   XXX-XXX-XXX  HIPR      HIPR       IS-NR          Active     -----
    1110   XXX-XXX-XXX  HIPR      HIPR       IS-NR          Active     -----
    1111   XXX-XXX-XXX  LIMT1     SS7HC      IS-NR          Active     -----
    1113   XXX-XXX-XXX  E5MCAP    OAMHC      IS-NR          Active     -----
    1114   -----------  E5TDM     -------    IS-NR          Active     -----
    1115   XXX-XXX-XXX  E5MCAP    OAMHC      IS-NR          Standby    -----
    1116   -----------  E5TDM     -------    IS-NR          Active     -----
    1117   -----------  E5MDAL    -------    IS-NR          Active     -----
    1201   XXX-XXX-XXX  LIMDS0    SS7ML      IS-NR          Active     -----
    1202   XXX-XXX-XXX  LIMDS0    SS7ML      IS-NR          Active     -----
    1203   XXX-XXX-XXX  LIMDS0    SS7ML      IS-NR          Active     -----
    1204   XXX-XXX-XXX  LIMDS0    SS7ML      IS-NR          Active     -----
    Command Completed.
;

Restoring Flash-Based Link Cards

Link cards include SS7HC, IPLHC, IPGHC, and ATMHC cards.

This procedure updates each card with the source release GPLs.

Note:

Steps 3 through 8 are to be repeated for EACH Link card in the system.

Issue the command to display the GPL status.

rept-stat-gpl:gpl=YYYY

(Where YYYY is one of the Flash-Based Link card types listed above.)

Response to the command is displayed.

Record the CARD locations for all cards which have alarms:

_____________________

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    rept-stat-gpl:gpl=YYYY
    Command entered at terminal #10.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    GPL Auditing  ON

    APPL       CARD      RUNNING           APPROVED      TRIAL
    XXXXXXX    1201      XXX-XXX-XXX ALM   XXX-XXX-XXX   XXX-XXX-XXX
    XXXXXXX    1202      XXX-XXX-XXX ALM   XXX-XXX-XXX   XXX-XXX-XXX
    XXXXXXX    1205      XXX-XXX-XXX ALM   XXX-XXX-XXX   XXX-XXX-XXX
    XXXXXXX    1207      XXX-XXX-XXX ALM   XXX-XXX-XXX   XXX-XXX-XXX
    XXXXXXX    1209      XXX-XXX-XXX       XXX-XXX-XXX   XXX-XXX-XXX
    XXXXXXX    1211      XXX-XXX-XXX       XXX-XXX-XXX   XXX-XXX-XXX
 Command Completed.
;

Issue command to display provisioned links.

rept-stat-card:loc=XXXX

(Where XXXX is a card in alarm from Step 1.)

Response displayed.

Note which links are IS-NR for this card.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    rept-stat-card:loc=XXXX
    Command entered at terminal #10.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE      APPL       PST            SST        AST
    XXXX   XXX-XXX-XXX  XXXXXX    XXXXXX     IS-NR          Active     -----
      ALARM STATUS       =  *  0021 Clock A for card failed, Clock B normal
      XXXXXX GPL version = XXX-XXX-XXX
      IMT BUS A          = Conn
      IMT BUS B          = Conn
      SLK A   PST        = IS-NR           LS=XXXX      CLLI=-----------
      SLK B   PST        = IS-NR           LS=XXXX      CLLI=-----------
      SLK A1  PST        = OOS-MT          LS=XXXX      CLLI=-----------
      SLK B1  PST        = IS-NR           LS=XXXX      CLLI=-----------
      SLK A2  PST        = IS-NR           LS=XXXX      CLLI=-----------
      SLK B2  PST        = IS-NR           LS=XXXX      CLLI=-----------
      SLK A3  PST        = IS-NR           LS=XXXX      CLLI=-----------
      SLK B3  PST        = IS-NR           LS=XXXX      CLLI=-----------
    Command Completed.
;

Issue the command to initialize the flash memory.
flash-card:code=appr:force=yes:loc=XXXX

Note:
this command causes the card to boot.

Response to the flash card command is displayed.

Wait for command complete to indicate that the card is finished loading before proceeding.
```
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    flash-card:code=appr:force=yes:loc=XXXX
    Command entered at terminal #10.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    Command Completed.
;
```

Issue command to display provisioned links.

rept-stat-card:loc=XXXX

Response displayed.

Verify that the links that were IS-NR in Step 4 are IS-NR now

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    rept-stat-card:loc=XXXX
    Command entered at terminal #10.
;

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE      APPL       PST          SST        AST
    XXXX   XXX-XXX-XXX  XXXXXX    XXXXXX     IS-NR        Active     XXXXX
      ALARM STATUS       = **  0228 REPT-E1F:FAC-E1 Port 1 LOS failure
      IMT    VERSION     = XXX-XXX-XXX
      PROM   VERSION     = XXX-XXX-XXX
      IMT BUS A          = Conn
      IMT BUS B          = Conn
      SLK A   PST        = IS-NR           LS=XXXX       CLLI=-----------
      SLK B   PST        = OOS-MT          LS=XXXX       CLLI=-----------
    Command Completed.
;

Repeat Steps 2 - 4 for each card in the group from Step 1 that has an alarm.
Repeat Steps 1-5 for each Flash-Based Link card group (Refer to Software Release Numbering to see list of GPLs.)

Issue the command to display the GPL status.

rept-stat-card

Response to the command is displayed.

Verify that all Flash-Based Link cards are IS-NR and are running the Source-Release GPL versions, as per your reference list of GPLs

For any card that is not IS-NR or running the correct GPL, repeat Steps 2-4.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    rept-stat-card
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    CARD   VERSION      TYPE    APPL       EST            SST        AST
    1101   XXX-XXX-XXX  DSM     SCCPHC     IS-NR          Active     -----
    1102   XXX-XXX-XXX  DSM     SCCPHC     IS-NR          Active     -----
    1103   XXX-XXX-XXX  TSM     GLSHC      IS-NR          Active     -----
    1104   XXX-XXX-XXX  TSM     GLSHC      IS-NR          Active     -----
    1105   XXX-XXX-XXX  DCM     IPGHC      IS-NR          Active     -----
    1111   XXX-XXX-XXX  IPSM    IPSHC      IS-NR          Active     -----
    1113   XXX-XXX-XXX  E5MCAP  OAMHC      IS-NR          Active     -----
    1114   -----------  E5TDM   -------    IS-NR          Active     -----
    1115   XXX-XXX-XXX  E5MCAP  OAMHC      IS-NR          Standby    -----
    1116   -----------  E5TDM   -------    IS-NR          Active     -----
    1117   -----------  E5MDAL  -------    IS-NR          Active     -----
    1201   XXX-XXX-XXX  LIMDS0  SS7ML      IS-NR          Active     -----
    1202   XXX-XXX-XXX  LIMDS0  SS7ML      IS-NR          Active     -----
    1203   XXX-XXX-XXX  LIMATM  ATMANSI    IS-NR          Active     -----
    1204   XXX-XXX-XXX  IPSM    IPSHC      IS-NR          Active     -----
    Command Completed.
;

Restoring Mux Cards

This procedure updates each card with the source release GPLs. Mux cards include HIPR, and HIPR2 cards, which run HIPR, and HIPR2 GPLs respectively.

Issue the card status command to identify the MUX cards in the system.

rept-stat-gpl:gpl=YYYY

(Where YYYY is one of the Flash-Based Mux card types listed above.)

Response to the command is displayed.

Record the CARD locations for all cards in the system:

_____________________

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 
    rept-stat-gpl:gpl=YYYY
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    GPL Auditing  ON

    APPL       CARD      RUNNING            APPROVED      TRIAL
    YYYY       XX09      XXX-XXX-XXX ALM    XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX10      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX09      XXX-XXX-XXX ALM    XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX10      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX09      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX10      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX09      XXX-XXX-XXX ALM    XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX10      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    Command Completed.
;

Enter the command to initialize the FLASH on the next Mux card on the current bus.

init-flash:loc=XXZZ:code=appr

(Where XX = is a shelf number and, ZZ depends on which bus is being flashed. 09 is bus A; 10 is bus B.)

Response to the flash initialization is shown.

    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 
    init-flash:loc=XX09:code=appr
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card XXZZ Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Download for card XXZZ Completed.
;

Repeat steps 1-2 for each Mux card type on the current bus.

Note:
Steps 1-2 must be performed for all MUX card types on one bus before performing these steps for any MUX card types on the other bus.

Enter the command to initialize the current bus.

init-mux:bus=x

Note:

Warning: Do not use the FORCE= parameter. Use of this parameter may result in network outage. Analysis of the alternate bus is required.

(Where x = A or B, depending on current bus: xx09 is bus A; xx10 is bus B.)

Response to the initialization command is displayed.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    init-mux:bus=a
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    5080.0014    CARD XXZZ YYYY          Card is present
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    5081.0014    CARD XXZZ YYYY          Card is present
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
*   5082.0004  * GPL SYSTEM YYYY          Card is running non-activated GPL

Issue the command to activate the flash on the next MUX card on the current bus.
act-flash:loc=XXZZ
(Where XX = is a shelf number and, ZZ depends on which bus is being flashed. 09 is bus A; 10 is bus B.)

Response to the activate command is displayed.
```
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    act-flash:loc=XXZZ
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Memory Activation for card XXZZ Started.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    FLASH Activation for card XXZZ Completed.
;
```
Repeat step 5 for each MUX card on the current bus (A or B.)
Repeat steps 2-6 for the second bus (A or B.)

Issue the command to display the MUX card GPL status.

rept-stat-gpl:gpl=YYYY

(Where YYYY is hipr for HIPR cards, or hipr2 for HIPR2 cards.)

Verify that all MUX card types are running the approved GPL.

eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    rept-stat-gpl:gpl=Y
    Command entered at terminal #10.
;
    eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y
    GPL Auditing  ON

    APPL       CARD      RUNNING            APPROVED      TRIAL
    YYYY       XX09      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX10      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX09      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX10      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX09      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX10      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX09      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    YYYY       XX10      XXX-XXX-XXX        XXX-XXX-XXX   XXX-XXX-XXX
    Command Completed.
;

Repeat step 8 for all MUX card types.