- EAGLE Software Upgrade Guide
- Software Upgrade Procedure
5 Software Upgrade Procedure
Call the Oracle support hotlines [see Appendix G] prior to executing this upgrade to ensure that the proper media are available for use.
Before upgrade, users must perform the EAGLE system health check [1]. This check ensures that the system to be upgraded is in an upgrade-ready state. Performing the system health check determines which alarms are present in the system and if upgrade can proceed with these alarms.
WARNING:
If there are cards in the system, which are not in IS-NR state, these cards should be brought to the IS-NR before the upgrade process is started. If it is not possible to bring the cards IS-NR, contact My Oracle Support [see Appendix G ].If any card cannot be brought in-service, the card should be inhibited after entering Phase 2 (during procedure 8). If any GLS card is in OOS-MT or IS-ANR state, none of the SCCP or LIM cards will load. The sequence of upgrade is such that cards providing support services to other cards will be upgraded first.WARNING:
Do not start the upgrade process without the required spare equipment; without spare equipment, recovery procedures cannot be executed!Please read the following notes on upgrade procedures:
- Procedure completion times shown here are estimates. Times may vary due to differences in database size, user experience, and user preparation.
- Command steps that require user entry are indicated with white-on-black step numbers.
- The shaded area within response steps must be verified in order to successfully complete that step.
- Where possible, EXACT command response outputs are shown. EXCEPTIONS are as
follows:
- Banner information is displayed in a format form only.
- System-specific configuration information such as card location, terminal port # assignments, and system features.
- ANY information marked with “XXXX” or “YYYY.” Where appropriate, instructions are provided to determine what output should be expected in place of “XXXX or YYYY”
- After completing each step and at each point where data is recorded from the screen, a check box should be provided.
- Captured data is required for future support reference.
- Each procedural step is numbered chronologically within each procedure.
Software Upgrade Execution – Session 1
Verifying Pre-Upgrade Requirements and Capturing Upgrade Data
Should THIS PROCEDURE FAIL, Contact the Oracle support hotlines [see My Oracle Support (MOS)] AND ASK FOR UPGRADE ASSISTANCE.
- Complete pre-upgrade tasksAll of the following tasks must be completed before continuing.
- Perform hardware inventory.
- Verify that all target-release baseline hardware has been installed. And any obsolete hardware has been replaced.
- Verify that a full complement of EAGLE® spares is available, including a
source-release fixed disk.
Note:
This fixed disk’s database should have been repaired in Upgrade Health Check [1]. - Verify that you have at least one source-release RMD with an up-to-date
database.
Note:
This drive’s database should have been backed up in Upgrade Health Check [1]. - Verify that you have one target-release upgrade media drives provided by Oracle for upgrade Or Target-Release software has been downloaded to the inactive disk partitions (see section 4.2).
- Verify that you have a copy of the Target Release’s System Release Notes (see section 1.3.)
- Verify that an EAGLE system health check has been performed and the output capture file has been validated by My Oracle Support.
- Perform upgrade time calculations to ensure that the upgrade can be completed within the window.
- Collect all measurement reports.
- Verify that all required documentation is included in the upgrade kit. [See section 4.2].
- Issue the command to display terminal status.
rtrv-trmResponse to retrieve terminal command is displayed.
- Record the terminals in the TRM column that have TYPE of PRINTER[1]. Also record the terminal being used to enter
commands (the user terminal)[2] Or terminals used by
external applications that issue commands to the EAGLE. In this example, terminal 12 is a printer, terminal 10 is the user terminal, and terminal 2 is KSR.
Capture _______
USER _______
Ext. Application: _______
See recommendation #1 & #6 in section 1.6
If not echoing to the printer or KSR, go to step 8.
- Record the initial output group configurations for the user’s and capture
terminals. Also, record the user’s TMOUT value.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y rtrv-trm Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y TRM TYPE COMM FC TMOUT MXINV DURAL 1 OAP 19200 -7-E-1 SW 30 5 00:01:00 2 KSR 9600 -7-E-1 SW 30 5 00:01:00 3 NONE 9600 -7-E-1 SW 30 5 00:01:00 4 NONE 9600 -7-E-1 SW 30 5 00:01:00 5 NONE 9600 -7-E-1 SW 30 5 00:01:00 6 NONE 9600 -7-E-1 SW 30 5 00:01:00 7 NONE 9600 -7-E-1 SW 30 5 00:01:00 8 NONE 9600 -7-E-1 SW 30 5 00:01:00 9 OAP 19200 -7-E-1 SW 30 5 00:01:00 10 KSR 9600 -7-E-1 SW 30 5 00:01:00 11 NONE 9600 -7-E-1 SW 30 5 00:01:00 12 PRINTER 9600 -7-E-1 SW 30 5 00:01:00 13 VT320 9600 -7-E-1 SW 30 5 00:01:00 14 NONE 9600 -7-E-1 SW 30 5 00:01:00 15 NONE 9600 -7-E-1 SW 30 5 00:01:00 16 NONE 9600 -7-E-1 SW 30 5 00:01:00 TRM TRAF LINK SA SYS PU DB 1 YES YES YES YES YES YES 2 NO NO NO NO NO NO 3 NO NO NO NO NO NO 4 NO NO NO NO NO NO 5 NO NO NO NO NO NO 6 NO NO NO NO NO NO 7 NO NO NO NO NO NO 8 NO NO NO NO NO NO 9 YES YES YES YES YES YES 10 YES YES YES YES YES YES 11 NO NO NO NO NO NO 12 YES YES YES YES YES YES 13 YES YES YES YES YES YES 14 NO NO NO NO NO NO 15 NO NO NO NO NO NO 16 NO NO NO NO NO NO ; USER ___ ___ ___ ___ ___ ___ TMOUT ___ CAP ___ ___ ___ ___ ___ ___ - Echo command input to capture terminal. If the capture terminal is the user
terminal go to step 7.
act-echo:trm=P(Where the value for P is one of the printer/KSR terminal port numbers recorded in step 3)
Response to activate command is displayed.eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y act-echo:trm=P Command entered at terminal #10. - If capture terminal’s output groups are not all set to YES, issue the change
terminal command.
chg-trm:trm=P:all=yes(P is the terminal port that is specified in step 5)
Response to change terminal command is displayed.eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y chg-trm:trm=P:all=yes Command entered at terminal #10. - If the output group and timeout on the user terminal are not set correctly,
issue the command to change terminal timeout and display groups.
chg-trm:trm=USER:all=no:sa=yes:sys=yes:db=yes:dbg:yes:tmout=0(Where the value of USER is the user terminal number shown in Step 2)
Response to change terminal command is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y chg-trm:trm=USER:sa=yes:sys=yes:db=yes:dbg:yes:tmout=0 Command entered at terminal #10. - Issue the command to display the system features
rtrv-featResponse to retrieve features command is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y EAGLE FEATURE LIST GTT = on GWS = on NRT = off X25G = off LAN = on CRMD = off SEAS = off LFS = off MTPRS = off FAN = on DSTN5000 = off WNP = off CNCF = off TLNP = off SCCPCNV = off TCAPCNV = off IPISUP = off X252000 = off PLNP = off NCR = off ITUMTPRS = on SLSOCB = off EGTT = on VGTT = on MPC = on ITUDUPPC = on MEASPLAT = on TSCSYNC = off E5IS = off - Issue the command to display the FAK features.
rtrv-ctrl-featResponse to retrieve command is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.yThe following features have been permanently enabled:
Feature Name Partnum Status Quantity FEATURE_A XXXXXXXXX on ---- FEATURE_B XXXXXXXXX on nnThe following features have been temporarily enabled:
Feature Name Partnum Status Quantity Trial Period Left Zero entries found.The following features have expired temporary keys:
Feature Name Partnum Zero entries found. - Issue the command to display the system serial number.
rtrv-serial-numResponse to retrieve command is displayed.
Record the system serial number as shown:
SN: ____________
Additionally, record in Appendix E.
- Verify the serial number is locked.
rtrv-serial-numCommand entered at terminal #4. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y System serial number = nt00009999 System serial number is locked. - Issue the command to retrieve records from the event log.
rtrv-log:dir=bkwd:edate=YYMMDD:etime=HHMMSS:snum=XXXX:enum=YYYY:num=NNN(Where YYMMDD is today’s date and HHMMSS is one hour ago.)
(Where XXXX, YYYY, and NNN are the values listed in Table 16.)
Response to retrieve command is displayed.
Determine if the report termination reason meets the pass/fail criteria in Table 17.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y Card 1113; SYS REL= 35.1.0-56.31.0; STP CLLI= tklc1190601; Timezone= EST ****06-09-19 10:49:46**** 1426.0311 DPC 012-095-015 DPC is allowed ****06-09-19 10:49:45**** 1424.0314 DPC 012-095-015 Route is allowed ****06-09-19 10:46:33**** 0667.0312 * DPC 012-095-015 DPC is restricted ****06-09-19 10:46:33**** 0665.0312 * DPC 012-095-015 DPC is restricted ****06-09-19 10:32:19**** 3100.0311 DPC 012-079-001 DPC is allowed ****06-09-19 10:32:18**** 3098.0314 DPC 012-079-001 Route is allowed ****06-09-19 10:30:41**** 2828.0312 * DPC 012-079-001 DPC is restricted ****06-09-19 10:30:41**** 2827.0316 DPC 012-079-001 Route is prohibited ****06-09-19 10:30:41**** 2825.0312 * DPC 012-086-004 DPC is restricted UAM Report terminated - max. or num= count reached END OF LOG REPORT. - Repeat steps 12 for all sets of UAMs listed in the following table:
Table 5-1 DDL-Hunt-related UAM ranges
SNUM ENUM NUM UAM Text* Start UAM End UAM Maximum Events 200 200 15 RCVRY-LFK: link available236 236 15 REPT-LFK: not aligned264 275 50 REPT-LINK-CGST:congestion level X to Y RCVRY-LINK-CGST:congestion has cleared REPT-LINK-CGST:discard level X to Y RVCRY-LINK-CGST:discard has cleared311 313 50 DPC is prohibited DPC is restricted DPC is allowed314 316 50 Route is prohibited Route is restricted Route is allowedTable 5-2 Retrieve Log Termination Pass/Fail Criteria
Termination Reason Pass/Fail Comment no records found within specified range Pass X records displayed (where X is less then NUM.) Pass max. or num= count reached Further Analysis Required See Determination and Recovery of DDL Hunt during Upgrade
Backing Up the Database
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support (MOS) AND ASK FOR UPGRADE ASSISTANCE.
- Issue the command to display database status.
rept-stat-dbResponse from the command is displayed.
Look in the columns labeled C and LEVEL output by this command.
Verify entries in column C show Y which indicates coherence.
Verify both FD CRNT Levels are equal.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y DATABASE STATUS: >> OK << TDM 1114 ( STDBY) TDM 1116 ( ACTV ) C LEVEL TIME LAST BACKUP C LEVEL TIME LAST BACKUP - -------- ---------------------- - -------- ---------------------- FD BKUP Y XXXX YY-MM-DD HH:MM:SS TTTT Y XXXX YY-MM-DD HH:MM:SS TTTT FD CRNT Y XXXX Y XXXX MCAP 1113 MCAP 1115 - -------- - -------- RD BKUP Y XXXX YY-MM-DD HH:MM:SS TTTT Y XXXX YY-MM-DD HH:MM:SS TTTT USB BKP - - - - - - - - - Issue the command to back up the database.
chg-db:action=backupResponse to backup command is displayed.
Command execution time: approximately 4 – 20 minutes, longer for large databases.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y 5042.1114 CARD 1115 Database BACKUP started Report Date:YY-MM-DD Time:hh:mm:ss ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP B - Backup starts on active MASP. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP B - Backup on active MASP to fixed disk complete. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP B - Backup starts on standby MASP. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y 5045.1116 CARD 1115 Database action ended - OK Report Date:YY-MM-DD Time:hh:mm:ss ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP B - Backup on standby MASP to fixed disk complete. ; - Insert the RMD containing the source release into the drive slot. Wait for the RMD to be detected by the system
- Issue the Change-Database command to back up the database to RMD.
chg-db:action=backup:dest=removeResponse to backup command is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y chg-db:action=backup:dest=remove Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y BACKUP (REMOVABLE): MASP A - Backup starts on active MASP ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y BACKUP (REMOVABLE): MASP A - Backup to removable device complete - Issue the command to copy the GPLs to RMD.
copy-gplResponse to copy command is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y copy-gpl Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y COPY GPL: MASP A - COPY STARTS ON ACTIVE MASP COPY GPL: MASP A - COPY TO REMOVABLE CARTRIDGE COMPLETE - Issue the command to report database status.
rept-stat-dbResponse to database status command is displayed.
Check that all DB levels are the same.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y DATABASE STATUS: >> OK << TDM 1114 ( STDBY) TDM 1116 ( ACTV ) C LEVEL TIME LAST BACKUP C LEVEL TIME LAST BACKUP - -------- ---------------------- - -------- ---------------------- FD BKUP Y XXX YY-MM-DD hh:mm:ss TTTT Y XXX YY-MM-DD hh:mm:ss TTTT FD CRNT Y XXX Y XXX MCAP 1113 MCAP 1115 - -------- - -------- RD BKUP - - - - Y XXX YY-MM-DD hh:mm:ss TTTT USB BKP - - - - - - - - - Issue the command to display GPL status.
rtrv-gplResponse from the retrieve command is displayed.
Verify that the GPL versions that are displayed in the RELEASE and REMOVE TRIAL columns are correct; see Software Release Numbering.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y GPL Auditing ON GPL CARD RELEASE APPROVED TRIAL REMOVE TRIAL GGGGGG1 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG1 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG1 1113 ----------- ----------- ----------- ----------- GGGGGG2 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG2 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG2 1113 ----------- ----------- ----------- ----------- GGGGGG3 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG3 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG3 1113 ----------- ----------- ----------- ----------- OAMHC 1114 XXX-XXX-XXX XXX-XXX-XXX ----------- ----------- OAMHC 1116 XXX-XXX-XXX XXX-XXX-XXX ----------- ----------- OAMHC 1113 ----------- ----------- ----------- ----------- GGGGGG4 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG4 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG4 1113 ----------- ----------- ----------- ----------- GGGGGG5 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG5 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG5 1113 ----------- ----------- ----------- ----------- GGGGGG6 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG6 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG6 1113 ----------- ----------- ----------- ----------- - Remove the Source-Release RMD. Store the RMD in a safe location.
Updating the Source-Release Spare Fixed Disk
- Issue the report card status command.
rept-stat-card:appl=oamResponse to the card status command is displayed.
Record the card locations of both MASPs as well as the part number of the E5-MASP:
Act E5-MASP ________ p/n _________________ Stby E5-MASP _______ p/n _______________CARD VERSION TYPE GPL PST SST AST 1113 XXX-XXX-XXX E5MCAP OAMHC IS-NR Standby ----- 1115 XXX-XXX-XXX E5MCAP OAMHC IS-NR Active ----- Command Completed. - Place spare E5-MASP in system.
- Record the part number for the spare E5-TDM:p/n _______________
- Slide the MASP H/S switch (SW3) on the standby MASP up to the unlocked position (Wait for all drive LEDs to transition to a steady blue). Remove the standby E5-MASP card determined in step 1.
- Insert the spare E5-MASP card. Slide the MASP H/S switch (SW3) on the new
standby MASP down to the locked position (Wait for the MASP H/S LED to
transition from blinking blue to off and the MASP to come up in standby
mode).
Note:
UAMs are generated during this step. An audible alarm is generated.Wait for the new standby MASP to come up in standby mode and system returns to duplex mode.
- Issue the report status command for the standby MASP.
rept-stat-card:loc=xxxx:mode=full(Where xxxx is the STBY MASP slot from step 1 above)
Verify that the backup goes to IS-NR
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST xxxx xxx-xxx-xxx E5MCAP OAMHC IS-NR Standby DB-DIFF ALARM STATUS = No Alarms. BLMCAP GPL version = XXX-XXX-XXX IMT BUS A = Conn IMT BUS B = Conn MBD BIP STATUS = Valid MOTHER BOARD ID = E5-MCAP DBD STATUS = Valid DBD TYPE = 1G ENET DBD MEMORY SIZE = 4096M HW VERIFICATION CODE = ---- CURRENT TEMPERATURE = 33C ( 92F) PEAK TEMPERATURE: = 37C ( 99F) [13-05-19 08:02] TROUBLE TEXT VER. = ---- IPLNK STATUS IPLNK IPADDR STATUS PST A 192.168.53.89 UP IS-NR Command Completed. - Issue the command to retrieve GPL versions.
rtrv-gplResponse from the retrieve command is displayed.
Verify correct source release levels.
If any of the standby E5-MASP GPLs indicate ALM, it is possible that the fixed disk has not gone through session 2 of the previous upgrade. Stop the procedure and contact My Oracle Support (MOS).
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y GPL Auditing ON GPL CARD RELEASE APPROVED TRIAL REMOVE TRIAL GGGGGG1 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG1 1116 XXX-XXX-XXX XXX-XXX-XXX ALM XXX-XXX-XXX ----------- GGGGGG1 1113 ----------- ----------- ----------- ----------- GGGGGG2 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG2 1116 XXX-XXX-XXX XXX-XXX-XXX ALM XXX-XXX-XXX ----------- GGGGGG2 1113 ----------- ----------- ----------- ----------- GGGGGG3 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG3 1116 XXX-XXX-XXX XXX-XXX-XXX ALM XXX-XXX-XXX ----------- GGGGGG3 1113 ----------- ----------- ----------- ----------- OAMHC 1114 XXX-XXX-XXX XXX-XXX-XXX ----------- ----------- OAMHC 1116 XXX-XXX-XXX XXX-XXX-XXX ----------- ----------- OAMHC 1113 ----------- ----------- ----------- ----------- GGGGGG4 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG4 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG4 1113 ----------- ----------- ----------- ----------- GGGGGG5 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG5 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG5 1113 ----------- ----------- ----------- ----------- GGGGGG6 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG6 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG6 1113 ----------- ----------- ----------- ----------- - Issue the command to repair the standby TDM’s database.
chg-db:action=repairNote:
The system will need approximately 2 minutes after step 5 to acquire duplex mode. As a result, the system will reject thechg-dbcommand until it is back in duplex mode.Response to the repair command is displayed.
Wait for the repair complete message to display and the MASP returns to in-service.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y chg-db:action=repair Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y REPAIR: MASP A - Repair starts on standby MASP. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y REPAIR: MASP A - Repair from fixed disk complete. - Place original standby E5-MASP in system.
- Slide the MASP H/S switch (SW3) on the standby MASP up to the unlocked position (Wait for all drive LEDs to transition to a steady blue).
- Remove the standby E5-MASP card determined in step 1.
- Insert the original standby E5-MASP card.
- Slide the MASP H/S switch (SW3) on the original standby MASP down to the locked
position (Wait for the MASP H/S LED to transition from blinking blue to off and
the MASP to come up in standby mode).
Note:
UAMs are generated during this step. An audible alarm is generated. - Wait for the original standby E5-MASP to come up in standby mode and system returns to duplex mode.
Verifying All Databases
- Issue the command to display database information.
rept-stat-db:display=allResponse to the command is displayed.
Look in the columns labeled ‘C,’ ‘T’, and ‘LEVEL’ output by this command.
Verify entries in column ‘C’ show ‘Y’, which indicates coherence.
Verify entries in column ‘T’ show ‘N’ (backup and RMD may show a dash), which indicates that the database is not in transition.
Verify all entries in the database LEVEL column are the same.
LEVEL is a value, which varies depending on the system.
If the STDBY databases are not coherent or not at the correct level, repeat Updating the Source-Release Spare Fixed Disk, step 8.
Verify that the MPS databases are coherent.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y DATABASE STATUS: >> OK << TDM 1114 ( STDBY) TDM 1116 ( ACTV ) C LEVEL TIME LAST BACKUP C LEVEL TIME LAST BACKUP - -------- ---------------------- - -------- ---------------------- FD BKUP Y YYY YY-MM-DD hh:mm:ss TTTT Y 1 - - FD CRNT Y XXX Y XXX MCAP 1113 MCAP 1115 - -------- - -------- RD BKUP - - - - Y 1 - - USB BKP - - - - - - - - CARD/APPL LOC C T LEVEL TIME LAST UPDATE EXCEPTION --------- ---- - - ---------- ----------------- -------------- SS7HC 1101 Y N XXX YY-MM-DD HH:MM:SS - IPLHC 1103 Y N XXX YY-MM-DD HH:MM:SS - VSCCP 1104 Y N XXX YY-MM-DD HH:MM:SS - ERTHC 1105 Y N XXX YY-MM-DD HH:MM:SS - MCP 1107 Y N XXX YY-MM-DD HH:MM:SS - GLS 1108 Y N XXX YY-MM-DD HH:MM:SS - IPSHC 1111 Y N XXX YY-MM-DD HH:MM:SS - OAM-RMV 1113 - - - - - - TDM-CRNT 1114 Y N XXX YY-MM-DD hh:mm:ss - TDM-BKUP 1114 Y - YYY YY-MM-DD hh:mm:ss - OAM-RMV 1115 Y - 1 00-00-00 00:00:00 DIFF LEVEL OAM-USB 1115 - - - - - - TDM-CRNT 1116 Y N XXX YY-MM-DD hh:mm:ss - TDM-BKUP 1116 Y - YYY YY-MM-DD hh:mm:ss - ELAP A ( STDBY ) C BIRTHDATE LEVEL EXCEPTION - ----------------- ---------- -------------- RTDB Y YY-MM-DD hh:mm:ss ZZZZZZZ - RTDB-EAGLE YY-MM-DD hh:mm:ss ZZZZZZZ - ELAP B ( ACTV ) C BIRTHDATE LEVEL EXCEPTION - ----------------- ---------- -------------- RTDB Y YY-MM-DD hh:mm:ss ZZZZZZZ - RTDB-EAGLE YY-MM-DD hh:mm:ss ZZZZZZZ - EAGLE RTDB REPORT CARD/APPL LOC C BIRTHDATE LEVEL EXCEPTION IN-SRVC --------- ---- - ----------------- ---------- ------------ ----------- VSCCP 1104 Y YY-MM-DD hh:mm:ss ZZZZZZZ - DDd HHh MMm - (Required) Enter text of second step here.(Optional) Enter the result of the step here.
Initializing MASPs to Run on Target-Release GPLs
- Remove the USB flash drives from E5-MASPs.
Note:
The target-release is assumed to have been downloaded to the inactive partition prior to the execution of this procedure (see Software Upgrade Preparation.) - Inhibit the standby MASP.
INH-CARD:LOC=XXXX(Where XXXX is the location of the standby MASP slot recorded in Updating the Source-Release Spare Fixed Disk, Step 1)
Response to the inhibit command is displayed
Verify UAM 514 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y Card is inhibited. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y ** 5045.0514 ** CARD XXXX OAMHC Standby MASP is inhibited ;Note:
Wait for the card to boot and return to the IMT bus. - Issue the report card status command.
rept-stat-card:appl=oamResponse to the card status command is displayed.
Verify that standby MASP is OSS-MT-DSBLD.
For this sample output, 1113 is standby and 1115 is Active.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST 1113 ----------- E5MCAP OAMHC OOS-MT-DSBLD Manual ----- 1115 XXX-XXX-XXX E5MCAP OAMHC IS-NR Active ----- - Download target-release flash to the standby MASP.
INIT-FLASH:LOC=XXXX:CODE=TRIAL(Where XXXX is the location used in the previous command)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y * 8003.0004 * GPL SYSTEM BLMCAP Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Retrieve the GPLs running on the card location.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location used in the previous command)
Response to the card status command is displayed.
The card should be running the trial version of the GPL. If the approved and trial versions are the same no ALM will be present.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y GPL CARD RUNNING APPROVED TRIAL OAMHC 1113 ----------- ----------- ----------- BLMCAP YYY-YYY-YYY ALM+ XXX-XXX-XXX YYY-YYY-YYY Command Completed. - Run the target-release GPL on the standby MASP
ALW-CARD:LOC=XXXX:CODE=INACTIVEPRTN(target release on the inactive partition)
(Where XXXX is the location of the standby MASP used in the previous command)
Response to allow-card command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y Card has been allowed. - Retrieve status of the MASPs
REPT-STAT-GPL:GPL=OAMHCVerify standby MASP running target release GPL. The standby MASP will display ALM to indicate that the card is not running the approved version GPL.
Note:
Standby MASP will not be displayed here if Eagle is getting upgraded from R46.4 or earlier to R46.5 or later. If so, run step 14 verify the GPL on standby MASP. Otherwise, go to step 9.eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y GPL Auditing ON GPL CARD RUNNING APPROVED TRIAL OAMHC 1113 XXX-XXX-XXX XXX-XXX-XXX OAMHC 1115 YYY-YYY-YYY XXX-XXX-XXX Command Completed. - Retrieve GPL status of the standby MASP.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of the standby MASP slot recorded in Updating the Source-Release Spare Fixed Disk, Step 1)
Verify standby MASP running target release GPLs. Here the standby MASP will display GPL as EOAM (instead of OAMHC) if Eagle is getting upgraded from R46.4 or earlier to R46.5 or later.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y GPL Auditing ON GPL CARD RUNNING APPROVED TRIAL EOAM 1115 140-030-000 ----------- ----------- BLMCAP 140-030-000 ALM+ 138-029-000 140-030-000 Command Completed. - Perform an OAM role change by booting the active MASP.
INIT-CARD:LOC=XXXX(Where XXXX is the location of the active MASP recorded in Updating the Source-Release Spare Fixed Disk, Step 1)
Response to card initialization is shown
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y Init Card command issued to card xxxx - Issue the command to log back in to the system.
LOGIN:UID=XXXXXX(Where XXXXXX is a valid login ID)
Response to login command is displayed.
Ignore any login failure message.
Verify the Upgrade Phase in Banner.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y Upg Phase 0 User logged in on terminal UU. ; ? Login failures since last successful LOGIN Last successful LOGIN was on port ? on ??-??-?? @ ??:??:?? - Echo command input to capture terminal.
ACT-ECHO:TRM=P(Where P is the terminal port number specified in Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 3)
Response to print capture command is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y Upg Phase x Scroll Area Output will be echoed to Port P. - Issue the card status to verify the location of the active MASP slot
REPT-STAT-CARD:APPL=OAMResponse to the card status command is displayed.
Circle the status of both E5-MASPs:
1113: Active or Standby
1115: Active or Standby
For this sample output, 1113 is active and 1115 is standby.
Note:
GPL & PST display for the standby MASP can be ignored.eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST 1113 XXX-XXX-XXX E5MCAP OAMHC IS-NR Active ----- 1115 XXX-XXX-XXX E5MCAP OAMHC IS-NR Standby ----- Command Completed - Inhibit the standby MASP
INH-CARD:LOC=XXXX(Where XXXX is the location of the standby MASP identified in the previous command)
Response to the inhibit command is displayed.
Verify UAM 514 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y Card is inhibited. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase x ** 5045.0514 ** CARD XXXX OAMHC Standby MASP is inhibited ;Note:
Wait for the card to boot and return to the IMT bus. - Download target release flash to the standby MASP.
INIT-FLASH:LOC=XXXX:CODE=TRIAL(Where XXXX is the location of the standby MASP used in the previous command)
Response to flash initialization is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ;Note:
Wait for card to boot and return to the IMT bus. - Retrieve the GPLs running on the card location.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of the standby MASP slot used in the previous command)
Response to the card status command is displayed.
The card should be running the trial version of the GPL. If the approved and trial versions are the same no ALM will be present.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLEEAGLE XX.x.x-YY.yy.y GPL CARD RUNNING APPROVED TRIAL OAMHC 1115 ----------- ----------- ----------- BLMCAP YYY-YYY-YYY ALM+ XXX-XXX-XXX YYY-YYY-YYY Command Completed. - Run the target release GPL on the standby MASP
ALW-CARD:LOC=XXXX:CODE=INACTIVEPRTN(target release on the inactive partition)
(Where XXXX is the location of the standby MASP used in the previous command)
Response to allow card command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y Card has been allowed. - Issue the command to display the status of the MASPs’ GPL
REPT-STAT-GPL:GPL=OAMHC69Response from the retrieve command is displayed.
Verify that the GPL versions that are displayed in the RUNNING column are correct; see Software Release Numbering.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y GPL Auditing ON APPL CARD RUNNING APPROVED TRIAL OAMHC69 1113 XXX-XXX-XXX ALM YYY-YYY-YYY XXX-XXX-XXX * OAMHC69 1115 XXX-XXX-XXX ALM YYY-YYY-YYY XXX-XXX-XXX * Command Completed.Note:
If no cards are displayed, repeat this step where gpl=oamhc. - If GPLs are not correct, do the following:
- Repeat Steps 2 - 17.
- Contact My Oracle Support (MOS).
- Issue the command to display the version of the Flash GPL running on card
1113.
REPT-STAT-CARD:LOC=1113:MODE=FULLResponse from the retrieve command is displayed.
Record version of BLMCAP running on E5-MASP.
GPL Version: ____________
GPL Version: ____________
Note:
For upgrade to release 46.6 & later, UAM 0225, "CARD running outdated Flash GPL" is displayed in Alarm Status.eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST 1113 XXX-XXX-XXX E5MCAP OAMHC IS-NR Standby ----- ALARM STATUS = No Alarms. BLMCAP GPL version = YYY-YYY-YYY IMT BUS A = Conn IMT BUS B = Conn CLOCK A = Active CLOCK B = Idle CLOCK I = Idle MBD BIP STATUS = Valid MOTHER BOARD ID = E5-MCAP DBD STATUS = Valid DBD TYPE = 1G ENET DBD MEMORY SIZE = 4096M HW VERIFICATION CODE = ---- TROUBLE TEXT VER. = ---- IPLNK STATUS IPLNK IPADDR STATUS PST A 192.168.53.89 UP IS-NR Command Completed. - Repeat steps 18 – 19, for location 1115.
Verifying the Target Release and Software Access Key
- Validate the Software Access Key with the upgrade target release.
ACT-UPGRADE:ACTION=CHKREL:SRC=FIXEDResponse from the software validation.
Verify the Upgrade target release is correct.
For pre-46.1 release, verify the Software Access Key is valid. SAK is not used from release 46.1 forward.
If either the upgrade target release is incorrect or the Software Access Key is invalid STOP the upgrade and contact My Oracle Support (MOS).
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y act-upgrade:action=chkrel:src=zzzz Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y Upgrade target: EAGLE XX.x.x.x.x-YY.y.y Software Access Key valid for target release Copy Release data to ramdisk. Validate Release data on ramdisk. Eagle Release successfully validated. Command Complete : Upgrade action completed successfully
OAM Conversion
Verifying all Databases
Note:
Refer to Configuring Card-Set Network Conversion Method to configure the Card Set network conversion method for target release 46.0 and higher.- Issue the command to display database status during upgrades.
ACT-UPGRADE:ACTION=DBSTATUSResponse to the command is displayed.
Look in the columns labeled ‘C’, ‘T’, and ‘LEVEL’ output by this command.
Verify entries in column ‘C’ show ‘Y’, which indicates coherence or ‘-‘.
Verify column ‘T’ shows ‘N’ for both CRNT databases, which indicates that those databases are not in transition
Or if target release is on the inactive partition, the database level is “1”.
Verify all entries in the database ‘Level’ column marked as ‘XXX’ are the same.
Verify that the version numbers displayed are correct.
DATABASE STATUS: >> OK << TDM 1114 ( STDBY) TDM 1116 ( ACTV ) C LEVEL TIME LAST BACKUP C LEVEL TIME LAST BACKUP - -------- ---------------------- - -------- ---------------------- FD BKUP Y XXX YY-MM-DD hh:mm:ss TTTT Y XXX YY-MM-DD hh:mm:ss TTTT FD CRNT Y XXX YY-MM-DD hh:mm:ss TTTT Y XXX YY-MM-DD hh:mm:ss TTTT MCAP 1113 MCAP 1115 - -------- - -------- RD BKUP - - - - - - - - USB BKP - - - - - - - - CARD/APPL LOC C T LEVEL TIME LAST UPDATE VERSION STATUS --------- ---- - - ---------- ----------------- ------------------- OAM-RMV 1113 - - - - - - TDM-CRNT 1114 Y N XXX YY-MM-DD hh:mm:ss XXX-XXX-XXX NORMAL TDM-BKUP 1114 Y - XXX YY-MM-DD hh:mm:ss XXX-XXX-XXX NORMAL OAM-RMV 1115 - - - - - - OAM-USB 1115 - - - - - - TDM-CRNT 1116 Y N XXX YY-MM-DD hh:mm:ss XXX-XXX-XXX NORMAL TDM-BKUP 1116 Y - XXX YY-MM-DD hh:mm:ss XXX-XXX-XXX NORMAL INACTIVE PARTITION GROUP CARD/APPL LOC C T LEVEL TIME LAST UPDATE VERSION STATUS --------- ---- - - ---------- ----------------- ------------------- TDM-CRNT 1114 Y - 1 YY-MM-DD hh:mm:ss ZZZ-ZZZ-ZZZ NORMAL TDM-BKUP 1114 Y - 1 YY-MM-DD hh:mm:ss ZZZ-ZZZ-ZZZ NORMAL TDM-CRNT 1116 Y - 1 YY-MM-DD hh:mm:ss ZZZ-ZZZ-ZZZ NORMAL TDM-BKUP 1116 Y - 1 YY-MM-DD hh:mm:ss ZZZ-ZZZ-ZZZ NORMAL - Issue the command to retrieve the upgrade configuration.
rtrv-upgrade-configResponse to the retrieve command is displayed.
If target rlease is 46.0 or 45.x, verify that SAK is set.
The Threshold Type will be GROUP or SET.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y Upg Phase x Software Access Key entered on system : vbsevhcea7vy5 Configured Upgrade Threshold Type: SET Number of SERVICE Sets: X Number of LINK Sets: Y Command Completed.Note:
Refer to Configuring Card-Set Network Conversion Method to configure the Card Set network conversion method.
STP Conversion
See recommendation #5 in Recommendations before executing this procedure.
If the upgrade execution terminates before successfully completing, see recommendation #7 in Recommendations.
- Issue the command to begin database conversion.Note that the duration of this command is dependent on the size of the database and the size of the network configuration. The duration can be from about two hours when using threshold type SET to up to 8-10 hours in large systems using threshold type GROUP.
Supplemental Information For Procedure 8, Step 2 contains messages illustrative of the output of upgrade during this series of operations.
- If the threshold type is set to SET in Verifying all Databases, Step 2 issue the following command:
ACT-UPGRADE:ACTION=CONVERTSTP:SRC=FIXEDNote:
While upgrading from Release 46.9 to Release 46.9.1 or later releases, change PURGEPERIOD to 0 using theCHG-ATTR-SECULOG:PURGEPERIOD=0command. - If the threshold type is set to GROUP in Verifying all Databases, Step 2, issue the following command:
ACT-UPGRADE:ACTION=CONVERTSTP:SRC=FIXED:THRES=75The following table lists the actions completed by the command:
Table 5-3 Act Upgrade Command Actions
Fixed workspace A OAM based measurements are inhibited. B N/A C The standby disk is formatted based on the target release configuration table. D The target release GPLs are copied onto the standby TDM. E The existing database is converted onto the standby disk, upgrading the existing EAGLE source-release tables to target-release tables. F The standby MASP boots automatically. G The active MASP then boots allowing the standby to resume the active role. Proceed to step 2 to log back into the system and restart output capture. H The standby disk is formatted based on the target release configuration table. I The target release GPLs are copied onto the standby TDM. J The existing database is converted onto the standby disk, upgrading the existing EAGLE source-release tables to target-release tables. K The standby MASP boots automatically. L Initialization of Network cards. Command is displayed.
Note the banners transitions from Phase 0 to Phase 3.
Software troubles from the DMS_LOCK.C module may be generated, for incremental upgrade only, while GPLs are being copied. These software troubles are not expected but, if they occur in this circumstance, they are not service affecting.
Completion notice of successful upgrade.
If upgrade does not complete successfully, see recommendation # 7 in section Recommendations.
eaglestp YY-MM-DD hh:mm:ss EST Rel XX.x.x-XX.x.x Upg Phase 0 act-upgrade:action=convertstp:thres=XX Command entered at terminal #10.NOTICE: One of the following messages will be output at the start of the upgrade process to indicate which workspace (fixed or removable) has been selected by the system for OAM conversion:
eaglestp YY-MM-DD hh:mm:ss EST Rel XX.x.x-XX.x.x Upg Phase 0 Using inactive standby partitions for OAM conversion (disk=dddd)(Where dddd defines conversion workspace)
NOTICE: See Samples of Message from Convertstp Action for Act-Upgrade Command for samples of output messages.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3 Command Complete : Upgrade action completed successfullyNote:
If upgrade terminates abnormally in phase 3 due to cards being in IS-ANR|DDL Hunt, contact My Oracle Support (MOS) for assistance in executing Determination and Recovery of DDL Hunt During Upgrade. - After item G in step 1, issue the command to log back in to the system.
LOGIN:UID=XXXXXX(Where XXXXX is a vald login ID)
Response to login command is displayed.
Ignore any login failure message.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase x User logged in on terminal 10. ? Login failures since last successful LOGIN Last successful LOGIN was on port ? on ??-??-?? @ ??:??:?? - Issue the command to reactivate printer capture of upgrade process.
ACT-ECHO:TRM=P(Where P is the terminal port number specified in Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 3)
Response to print capture command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase x Scroll Area Output will be echoed to Port P. - Issue the command to display database status during upgrades.
ACT-UPGRADE:ACTION=DBSTATUSResponse from the command is displayed.
Look in the columns labeled ‘C’, ‘LEVEL’ and ‘VERSION STATUS’ output by this command.
Verify entries in column ‘C’ show ‘Y’ which indicates coherence or ‘-‘.
Verify both ‘FD CRNT’ Levels are equal.
Verify ‘VERSION STATUS’ shows NORMAL in the active partition group. NOTE: this will not occur until step 2 above is completed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase x DATABASE STATUS: >> OK << TDM 1114 ( STDBY) TDM 1116 ( ACTV ) C LEVEL TIME LAST BACKUP C LEVEL TIME LAST BACKUP - -------- ---------------------- - -------- ---------------------- FD BKUP Y XXX YY-MM-DD hh:mm:ss TTTT Y XXX YY-MM-DD hh:mm:ss TTTT FD CRNT Y XXX YY-MM-DD hh:mm:ss TTTT Y XXX YY-MM-DD hh:mm:ss TTTT MCAP 1113 MCAP 1115 - -------- - -------- RD BKUP - - - - - - - - USB BKP - - - - - - - - CARD/APPL LOC C T LEVEL TIME LAST UPDATE VERSION STATUS --------- ---- - - ---------- ----------------- ------------------- OAM-RMV 1113 - - - - - - TDM-CRNT 1114 Y N XXX YY-MM-DD hh:mm:ss XXX-XXX-XXX NORMAL TDM-BKUP 1114 Y - XXX YY-MM-DD hh:mm:ss XXX-XXX-XXX NORMAL OAM-RMV 1115 - - - - - - OAM-USB 1115 - - - - - - TDM-CRNT 1116 Y N XXX YY-MM-DD hh:mm:ss XXX-XXX-XXX NORMAL TDM-BKUP 1116 Y - XXX YY-MM-DD hh:mm:ss XXX-XXX-XXX NORMAL INACTIVE PARTITION GROUP CARD/APPL LOC C T LEVEL TIME LAST UPDATE VERSION STATUS --------- ---- - - ---------- ----------------- ------------------- TDM-CRNT 1114 Y - ZZZ YY-MM-DD hh:mm:ss ZZZ-ZZZ-ZZZ UPG 3 TDM-BKUP 1114 Y - ZZZ YY-MM-DD hh:mm:ss ZZZ-ZZZ-ZZZ UPG 3 TDM-CRNT 1116 Y - ZZZ YY-MM-DD hh:mm:ss ZZZ-ZZZ-ZZZ UPG 3 TDM-BKUP 1116 Y - ZZZ YY-MM-DD hh:mm:ss ZZZ-ZZZ-ZZZ UPG 3 - Issue the report card status command to verify network cards.
REPT-STAT-CARDResponse to the card status command is displayed.
Verify that the cards are IS-NR, OOS-MT | Isolated or OOS-MT-DSBLD.
Verify that the GPL versions that are displayed in the “VERSION” column are correct; see Software Release Numbering.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase x CARD VERSION TYPE APPL PST SST AST 1101 XXX-XXX-XXX DSM SCCPHC IS-NR Active ----- 1102 XXX-XXX-XXX DSM SCCPHC IS-NR Active ----- 1103 XXX-XXX-XXX TSM GLSHC IS-NR Active ----- 1104 XXX-XXX-XXX TSM GLSHC IS-NR Active ----- 1105 XXX-XXX-XXX LIMDS0 SS7ML IS-NR Active ----- 1111 XXX-XXX-XXX IPSM IPSHC OOS-MT Isolated ----- 1113 XXX-XXX-XXX E5MCAP OAMHC IS-NR Active ----- 1114 ----------- E5TDM ------- IS-NR Active ----- 1115 XXX-XXX-XXX E5MCAP OAMHC IS-NR Standby ----- 1116 ----------- E5TDM ------- IS-NR Active ----- 1117 ----------- E5MDAL ------- IS-NR Active ----- 1201 XXX-XXX-XXX LIMDS0 SS7ML IS-NR Active ----- 1202 XXX-XXX-XXX LIMDS0 SS7ML IS-NR Active ----- 1203 XXX-XXX-XXX LIMT1 SS7ML IS-NR Active ----- 1204 XXX-XXX-XXX LIMT1 SS7HC IS-NR Active ----- 1205 XXX-XXX-XXX DCM SS7IPGW IS-NR Active ----- 1207 XXX-XXX-XXX DCM IPGWI IS-NR Active ----- 1211 XXX-XXX-XXX LIMDS0 MPLGA IS-NR Active ----- 1215 xxx-xxx-xxx DSM SCCPHC IS-NR Active ----- 1217 xxx-xxx-xxx DSM SCCPHC IS-NR Active ----- 3101 xxx-xxx-xxx LIMATM ATMANSI IS-NR Active ----- 3102 xxx-xxx-xxx LIMATM ATMANSI IS-NR Active ----- Command Completed. - Issue the command to display GPL status.
RTRV-GPLResponse from the retrieve command is displayed.
Verify that the GPL versions that are displayed in the “RELEASE” column are correct; see Software Release Numbering.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y GPL Auditing ON GPL CARD RELEASE APPROVED TRIAL REMOVE TRIAL GGGGGG1 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG1 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG1 1113 ----------- ----------- ----------- ----------- GGGGGG2 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG2 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG2 1113 ----------- ----------- ----------- ----------- GGGGGG3 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG3 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG3 1113 ----------- ----------- ----------- ----------- OAMHC 1114 XXX-XXX-XXX XXX-XXX-XXX ----------- ----------- OAMHC 1116 XXX-XXX-XXX XXX-XXX-XXX ----------- ----------- OAMHC 1113 ----------- ----------- ----------- ----------- GGGGGG4 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG4 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG4 1113 ----------- ----------- ----------- ----------- GGGGGG5 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG5 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG5 1113 ----------- ----------- ----------- ----------- GGGGGG6 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG6 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG6 1113 ----------- ----------- ----------- -----------
Completion of Session 1
Migrate to VxWorks6.9
Migrate the OAM and selected modules to VxWorks 6.9 if target release is 46.6 or above.
If the source release is 46.5 or prior and the target release is 46.6 or later, then execute Migrate the MASP Cards Running VxWorks 6.4 GPL to VxWorks 6.9 GPL through IPS Application is Provisioned on SLIC Card, Migrate the Same to VxWorks6.9. Otherwise, go to Completing Upgrade/Return to Full-Function Mode.
If the display/report is for a command such as RTRV-GPL, or REPT-STAT-GPL, any command intended to display or Operate on a particular GPL, then EAGLE displays the correct GPL name, i.e.: OAMHC or OAMHC69. But when the command intends to display the status of a card, then EAGLE displays the generic name that is OAMHC for OAMHC and/or OAMHC69, MCPHC for MCPHC and/or MCPHC69; IPSHC for IPSHC and/or IPSMHC69.
Migrate the MASP Cards Running VxWorks 6.4 GPL to VxWorks 6.9 GPL
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- Issue the card status to verify the location of the active/standby MASP
slots.
REPT-STAT-CARD:APPL=OAMResponse to the card status command is displayed.
Record the MASP in the standby role:
Standby: 1113 or 1115
For this sample output, 1113 is active and 1115 is standby.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST 1113 XXX-XXX-XXX E5MCAP OAMHC IS-NR Active ----- 1115 XXX-XXX-XXX E5MCAP OAMHC IS-NR Standby ----- Command Completed. ; - Report the GPLs running on the card location.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of the standby MASP slot display in the above step.)
Response from the status command is displayed.
Record the flash image running on the standby MASP:
BLMCAP or BLDC32
If the “ALM” indicator is displayed for the card’s flash image, continue. Or if the card is running BLMCAP, continue. Otherwise, go to step 12.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y Upg Phase 3 GPL CARD RUNNING APPROVED TRIAL OAMHC XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ZZZZZZ YYY-YYY-YYY ALM YYY-YYY-YYY YYY-YYY-YYY Command Completed. ; - Issue the command to inhibit the standby MASP.
INH-CARD:LOC=XXXX(Where XXXX is the location of the standby MASP slot used in the previous command.)
Response to the inhibit command is displayed
Verify UAM 514 is displayed.
If the ALM indication was displayed in step 4, continue. Otherwise, go to step 6.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 Card is inhibited. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 ** 5045.0514 ** CARD XXXX OAMHC Standby MASP is inhibited ;Note:
Wait for the card to boot and return to the IMT bus. - Download the approved version flash to the standby MASP.
INIT-FLASH:LOC=XXXX:CODE=APPR(Where XXXX is the location of the standby MASP slot used in the previous command.)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
If the card is running BLMCAP, continue. Otherwise, go to step 9.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 8003.0004 * GPL SYSTEM ZZZZZZ Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash on standby MASP.
ACT-FLASH:loc=XXXX(Where XXXX is the location of the standby MASP slot used in the previous command.)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Activation for card XXXX Completed. ; - Issue flash command to download the bootloader image.
INIT-FLASH:LOC=XXXX:MODE=RPLCEBL:BITS=32(Where XXXX is the location of the standby MASP slot used in the previous command.)
Response to flash command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 BOOTLOADER change for card XXXX SUCCESSFUL. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 Command Completed. ; - Issue command to download approved flash image.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLDC32(Where XXXX is the location used in the previous command)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 8003.0004 * GPL SYSTEM BLDC32 Card is running non-activated GPL ; - Retrieve the GPLs running on the card location.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location used in the previous command)
Response to the GPL status command is displayed.
Verify that card is running BLDC32 GPL.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 GPL CARD RUNNING APPROVED TRIAL OAMHC XXXX ----------- ----------- ----------- BLDC32 YYY-YYY-YYY+ YYY-YYY-YYY XXX-XXX-XXX Command Completed. ; - Issue command to activate the flash on standby MASP.
ACT-FLASH:loc=XXXX(Where XXXX is the location of the standby MASP used in the previous command)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Activation for card XXXX Completed. ; - Issue command to allow the standby MASP.
ALW-CARD:LOC=XXXX(Where XXXX is the location of the standby MASP used in the previous command)
Response to allow-card command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 Card has been allowed. ; - Issue command to report the status of the Standby MASP.
REPT-STAT-CARD:LOC=XXXX:MODE=FULL(Where XXXX is the location of the standby MASP used in the previous command.)
Response to the card’s status report is displayed.
Verify that the standby MASP is running the BLDC32 flash GPL.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y Upg Phase 3 CARD VERSION TYPE GPL PST SST AST xxxx xxx-xxx-xxx E5MCAP OAMHC IS-NR Standby --- ALARM STATUS = No Alarms. BLDC32 GPL version = YYY-YYY-YYY IMT BUS A = Conn IMT BUS B = Conn MBD BIP STATUS = Valid MOTHER BOARD ID = E5-MCAP DBD STATUS = Valid DBD TYPE = 1G ENET DBD MEMORY SIZE = 4096M HW VERIFICATION CODE = ---- CURRENT TEMPERATURE = 33C ( 92F) PEAK TEMPERATURE: = 37C ( 99F) [13-05-19 08:02] TROUBLE TEXT VER. = ---- IPLNK STATUS IPLNK IPADDR STATUS PST A XXX.XXX.XX.XX UP IS-NR Command Completed. ; - If this is the first pass through this procedure, issue command to boot the
active MASP. Otherwise, continue to next procedure.
INIT-CARD:LOC=YYYY(Where YYYY is the location of the active MASP)
Response to card initialization is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 Init Card command issued to card YYYY ; - Issue the command to log back in to the system.
LOGIN:UID=XXXXXX(Where XXXXXX is a valid login ID)
Response to login command is displayed.
Ignore any login failure message.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y User logged in on terminal UU. ; ? Login failures since last successful LOGIN Last successful LOGIN was on port ? on ??-??-?? @ ??:??:?? - Echo command input to capture terminal.
ACT-ECHO:TRM=P(Where P is the terminal port number specified in Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 3)
Response to print capture command is displayed.
Repeat Steps 1 – 11 for the formerly active MASP.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y Scroll Area Output will be echoed to Port P. ;
Migrate the MCPM Cards Running VxWorks 6.4 GPL to VxWorks 6.9 GPL
Execute the below procedure for every MCPM card present in the system.
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- If the source release was 46.5 or prior, issue the MCPM card status command.
Otherwise, continue to next procedure.
REPT-STAT-CARD:APPL=MCPResponse to the card status command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST XXXX XXX-XXX-XXX MCPM MCPHC IS-NR Active ----- XXXX XXX-XXX-XXX MCPM MCPHC IS-NR Active ----- Command Completed. ; - For each MCPM-type card listed above, issue the GPL status command.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of a MCPM card slot listed in previous step.)
Response to the status command is displayed.
If the “ALM” indictor is displayed for the card’s flash image, continue. If card is running BLMCAP, continue. Otherwise repeat step 2 for next MCPM card in list.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y GPL CARD RUNNING APPROVED TRIAL MCPHC XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ZZZZZZ ZZZ-ZZZ-ZZZ ALM YYY-YYY-YYY YYY-YYY-YYY Command Completed. - Issue command to inhibit the card.
INH-CARD:LOC=XXXX(Where XXXX is the location of the MCPM card use in previous command.)
Response to the inhibit command is displayed
If the ALM indication was displayed in step 2, continue. Otherwise, go to step 6.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Card has been inhibited. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Command Completed. ;Note:
Wait for the card to boot and return to the IMT bus. - Issue command to download approved flash image.
INIT-FLASH:LOC=XXXX:CODE=APPR(Where XXXX is the location of the MCPM card use in previous command.)
Response to flash initialization is shown.
Verify UAM 0004 is displayed. If card is running BLDC32, go to step 5. Otherwise, continue.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 8003.0004 * GPL SYSTEM ZZZZZZ Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:LOC=XXXX(Where XXXX is the location of the MCPM card use in previous command.)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue flash command to download the bootloader image.
INIT-FLASH:LOC=XXXX:MODE=RPLCEBL:BITS=64(Where XXXX is the location of the MCPM card use in previous command.)
Response to flash command is shown.
If either response is displayed, then proceed to the next step.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y BOOTLOADER change for card XXXX SUCCESSFUL. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Command Completed. ; OR If the bootloader was succesfully downloaded previously: eaglestp 17-01-20 12:19:04 MST EAGLE XX.x.x.x.x-YY.y.y BOOTLOADER not changed for card XXXX. Already running requested bootloader. ; eaglestp 17-01-20 12:19:04 MST EAGLE XX.x.x.x.x-YY.y.y Command Completed. ; - Download target-release flash to the MCPM card.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLDC32(Where XXXX is the location used in the previous command)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y * 8003.0004 * GPL SYSTEM BLDC32 Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:loc=XXXX(Where XXXX is the location of the MCPM card used in the previous command)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue the allow command to reload the MCPM card.
ALW-CARD:LOC=XXXX(Where XXXX is the location of the card used in the previous command)
Response to allow-card command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Card has been allowed. ; - Retrieve status of the MCPM card if present in the system.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of the card used in the previous command)
Response to GPL status command.
Verify that MCPM card is BLDC32 GPL.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y GPL Auditing ON GPL CARD RUNNING APPROVED TRIAL MCPHC69 XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLDC32 YYY-YYY-YYY YYY-YYY-YYY YYY-YYY-YYY Command Completed. ; - Issue command to report the status of the measurement system.
REPT-STAT-MEASResponse to Measurement status command.
Verify that MCPM cards have returned to IS-NR
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y PST SST AST MEAS SS IS-NR Active ----- ALARM STATUS = No Alarms CARD VERSION TYPE PST SST AST XXXX P XXX-XXX-XXX MCPM IS-NR Active ----- IP Link A IS-NR Active ----- XXXX XXX-XXX-XXX MCPM IS-NR Active ----- IP Link A IS-NR Active ----- CARD XXXX ALARM STATUS = No Alarms CARD XXXX ALARM STATUS = No Alarms Command Completed. ; - If this is the last card listed in Step 1, continue to next procedure.
Otherwise, repeat Steps 2 - 11 for the next card listed in Step 1.
Note:
Wait till this flashed MCPM card to complete reloading before proceeding to next step.
MCP Application is Provisioned on SLIC Card, Migrate the Same to VxWorks6.9
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- If the source release was 46.5 or prior, issue the MCPM card status command.
Otherwise, continue to next procedure.
REPT-STAT-CARD:APPL=MCPResponse to the card status command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST XXXX XXX-XXX-XXX SLIC MCPHC IS-NR Active ----- XXXX XXX-XXX-XXX SLIC MCPHC IS-NR Active ----- Command Completed. ; - For each card with type equal to SLIC listed above, issue the GPL status
commend.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of a MCPM/SLIC card slot listed in previous step.)
Response to the GPL status command is displayed.
If the ALM indictor is displayed for the card’s flash image, continue. If card is running BLSLC32, continue. Otherwise repeat step 2 for next SLIC card in list.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y GPL CARD RUNNING APPROVED TRIAL MCPHC XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLSLC32 ZZZ-ZZZ-ZZZ ALM YYY-YYY-YYY YYY-YYY-YYY Command Completed. - Issue command to inhibit the card.
INH-CARD:LOC=XXXX(Where XXXX is the location of the MCPM/SLIC card)
Response to the inhibit command is displayed
If the ALM indication was displayed in step 2, continue. Otherwise, go to step 6.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Card has been inhibited. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Command Completed. ;Note:
Wait for the card to boot and return to the IMT bus. - Issue command to download approved flash image.
INIT-FLASH:LOC=XXXX:CODE=APPR(Where XXXX is the location of the MCPM card use in previous command.)
Response to flash initialization is shown. Verify UAM 0004 is displayed. If card is running BLSL932, go to step 5. Otherwise, continue.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 8003.0004 * GPL SYSTEM ZZZZZZ Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:LOC=XXXX(Where XXXX is the location of the MCPM card use in previous command.)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Activation for card XXXX Completed. ; - Issue flash command to download target-release flash to the MCPM card.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLSL932(Where XXXX is the location used in the previous command)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y * 8003.0004 * GPL SYSTEM BLSL932 Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:LOC=XXXX(Where XXXX is the location of the MCPM card used in the previous command)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue the allow command to reload the MCPM card.
ALW-CARD:LOC=XXXX(Where XXXX is the location of the card used in the previous command)
Response to allow-card command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Card has been allowed. ; - Issue command to report GPL status.
REPT-STAT-GPL:LOC=XXXXResponse to GPL status command.
Verify that MCPM card is running BLSL932 GPL.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y GPL Auditing ON GPL CARD RUNNING APPROVED TRIAL MCPHC69 XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLSL932 YYY-YYY-YYY YYY-YYY-YYY YYY-YYY-YYY Command Completed. ; - Issue command to report the status of the measurement system.
REPT-STAT-MEASResponse to Measurement status command.
Verify that MCPM cards have returned to IS-NR
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y PST SST AST MEAS SS IS-NR Active ----- ALARM STATUS = No Alarms CARD VERSION TYPE PST SST AST XXXX P XXX-XXX-XXX MCPM IS-NR Active ----- IP Link A IS-NR Active ----- XXXX XXX-XXX-XXX MCPM IS-NR Active ----- IP Link A IS-NR Active ----- CARD XXXX ALARM STATUS = No Alarms CARD XXXX ALARM STATUS = No Alarms Command Completed. ; - If this is last card listed in Step 1, continue to next procedure. Otherwise,
repeat Steps 2 - Step 9 for the next card listed in Step 1.
Note:
Wait till this flashed MCPM card to complete reloading before proceeding to next step.
Migrate the IPS (ENET-B) Cards Running VxWorks 6.4 GPL to VxWorks 6.9 GPL
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- If the source release was 46.5 or prior, issue the IPSM card status command.
Otherwise, continue to next procedure.
REPT-STAT-CARD:APPL=IPSResponse to the card status command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST XXXX XXX-XXX-XXX IPSM IPSHC IS-NR Active ----- XXXX XXX-XXX-XXX IPSM IPSHC IS-NR Active ----- Command Completed. ; - For each IPSM-type card listed above, issue the GPL status commend.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of an IPSM card slot listed in previous step.)
Response to the status command is displayed. If the ALM indictor is displayed for the card’s flash image, continue. If card is running BLMCAP, continue. Otherwise repeat step 2 for next IPSM card in list.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y GPL CARD RUNNING APPROVED TRIAL IPSHC XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ZZZZZZ ZZZ-ZZZ-ZZZ ALM YYY-YYY-YYY YYY-YYY-YYY Command Completed. - Issue command to inhibit the card.
INH-CARD:LOC=XXXX(Where XXXX is the location of the IPSM card use in previous command.)
Response to the inhibit command is displayed.
If the ALM indication was displayed in step 2, continue. Otherwise, go to step 6.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Card has been inhibited. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Command Completed. ;Note:
Wait for the card to boot and return to the IMT bus. - Issue command to download approved flash image.
INIT-FLASH:LOC=XXXX:CODE=APPR(Where XXXX is the location of the IPSM card use in previous command.)
Response to flash initialization is shown. Verify UAM 0004 is displayed. If card is running BLDC32, go to step 5. Otherwise, continue.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 8003.0004 * GPL SYSTEM ZZZZZZ Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:loc=XXXX(Where XXXX is the location of the IPSM card use in previous command.)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue flash command to download the bootloader image.
INIT-FLASH:LOC=XXXX:MODE=RPLCEBL:BITS=64(Where XXXX is the location of the IPSM card use in previous command.)
Response to flash command is shown. If either response is displayed, then proceed to the next step.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y BOOTLOADER change for card XXXX SUCCESSFUL. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Command Completed. ; OR If the bootloader was succesfully downloaded previously: eaglestp 17-01-20 12:19:04 MST EAGLE XX.x.x.x.x-YY.y.y BOOTLOADER not changed for card XXXX. Already running requested bootloader. ; eaglestp 17-01-20 12:19:04 MST EAGLE XX.x.x.x.x-YY.y.y Command Completed. ; - Download target-release flash to the IPSM card.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLDC32(Where XXXX is the location of the IPSM card use in previous command.)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y * 8003.0004 * GPL SYSTEM BLDC32 Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:loc=XXXX(Where XXXX is the location of the IPSM card used in the previous command)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue the allow command to reload the IPSM card.
ALW-CARD:LOC=XXXX(Where XXXX is the location of the card used in the previous command)
Response to allow-card command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Card has been allowed. ; - Retrieve status of the IPSM card if present in the system.
REPT-STAT-GPL:LOC=XXXXResponse to GPL status command.
Verify that IPSM card is running BLDC32 flash GPL
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y GPL Auditing ON GPL CARD RUNNING APPROVED TRIAL IPSHC69 XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLDC32 YYY-YYY-YYY YYY-YYY-YYY YYY-YYY-YYY Command Completed. ; - If this is the last card listed in Step 1, continue to next procedure.
Otherwise, repeat Steps 2 - 10 for the next card listed in Step 1.
Note:
Wait till this flashed IPSM card to complete reloading before proceeding to next step.
IPS Application is Provisioned on SLIC Card, Migrate the Same to VxWorks6.9
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- If the source release was 46.5 or prior, issue the IPSM card status command.
Otherwise, continue to next procedure.
REPT-STAT-CARD:APPL=IPSResponse to the card status command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST XXXX XXX-XXX-XXX SLIC IPSHC IS-NR Active ----- XXXX XXX-XXX-XXX SLIC IPSHC IS-NR Active ----- Command Completed. ; - For each IPSM/SLIC card listed above, issue the GPL status commend.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of the IPSM/SLIC card slot listed in previous step.)
Response to the GPL status command is displayed.
If the ALM indictor is displayed for the card’s flash image, continue. If card is running BLSLC32, continue.
Otherwise repeat step 2 for next SLIC card in list.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y GPL CARD RUNNING APPROVED TRIAL IPSHC XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLSLC32 ZZZ-ZZZ-ZZZ ALM YYY-YYY-YYY YYY-YYY-YYY Command Completed. - Issue command to inhibit the card.
INH-CARD:LOC=XXXX(Where XXXX is the location of the IPSM/SLIC card slot listed in previous step.)
Response to the inhibit command is displayed.
If the ALM indication was displayed in step 2, continue. Otherwise, go to step 6.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Card has been inhibited. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Command Completed. ;Note:
Wait for the card to boot and return to the IMT bus. - Issue command to download approved flash image.
INIT-FLASH:LOC=XXXX:CODE=APPR(Where XXXX is the location of the IPSM/SLIC card use in previous command.)
Response to flash initialization is shown. Verify UAM 0004 is displayed. If card is running BLSL932, go to step 5. Otherwise, continue.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 8003.0004 * GPL SYSTEM ZZZZZZ Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:loc=XXXX(Where XXXX is the location of the IPSM/SLIC card use in previous command.)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue flash command to download target-release flash to the IPSM/SLIC
card.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLSL932(Where XXXX is the location used in the previous command)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y * 8003.0004 * GPL SYSTEM BLSL932 Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:loc=XXXX(Where XXXX is the location of the IPSM/SLIC card used in the previous command)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue the allow command to reload the IPSM card.
ALW-CARD:LOC=XXXX(Where XXXX is the location of the card used in the previous command)
Response to allow-card command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Card has been allowed. ; - Issue command to report GPL status.
REPT-STAT-GPL:LOC=XXXXResponse to GPL status command.
Verify that IPSM card is running BLSL932 GPL.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y GPL Auditing ON GPL CARD RUNNING APPROVED TRIAL IPSHC69 XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLSL932 YYY-YYY-YYY YYY-YYY-YYY YYY-YYY-YYY Command Completed. ;If this is last card listed in Step 1, continue to next procedure. Otherwise, repeat Steps 2 - Step 9 for the next card listed in Step 1.
Note:
Wait till this flashed IPSM/SLIC card to complete reloading before proceeding to next step.
Completing Upgrade/Return to Full-Function Mode
Verification of the GPL distribution is also performed.
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- If system remains in upgrade mode, issue the command to initialize both MASPs.
Otherwise, go to step 4.
INIT-CARD:APPL=OAMResponse to the init command is displayed.
Verify the banner display full-function mode after the MASPs boot.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase x init-card:appl=oam Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 0002.0009 CARD 1113 OAMHC MASP became active ; - Issue the command to log back in to the system.
LOGIN:UID=XXXXXX(Where XXXXXX is a valid login ID)
Response to login command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y User logged in on terminal 10. ; - Issue the command to reactivate printer capture.
ACT-ECHO:TRM=P(Where P is the terminal port number specified in Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 5)
Response to printer capture command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y act-echo:trm=X Command entered at terminal #10. ; - Issue the command to display card status.
REPT-STAT-GPL:DISPLAY=ALLResponse to GPL status command is displayed.
Verify that no “ALM” indicator is displayed.
If GPL versions are not displayed, wait for the MASPs to return to service and re-issue the command.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y GPL Auditing ON GPL CARD RUNNING APPROVED TRIAL OAMHC 1113 XXX-XXX-XXX ALM XXX-XXX-XXX XXX-XXX-XXX * BLDC32 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX OAMHC 1115 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX * BLDC32 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ATMHC 1206 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLIXP XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 1209 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 1210 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR 1109 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR 1110 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX SS7HC 1201 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLIXP XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX SS7HC 1202 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLIXP XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GLSHC 1213 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLIXP XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GLSHC 1214 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLIXP XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX SCCPHC 1107 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLIXP XXX-XXX-XXX ALM XXX-XXX-XXX XXX-XXX-XXX SCCPHC 1111 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLIXP XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX Command Completed. ; - Establish system status.See recommendation # 7 in Recommendations.
Backing Up Converted Database
This procedure backs up the converted Target-Release database to the fixed disk and to either the removable media or the DB FTP server if provisioned. Verification of the converted database is also done.
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- If the target release was on the RMD, insert the target-release RMD. Then go to
step 6. If a source-release RMD is available and the target release was on the
inactive partition, insert the RMD and continue. Otherwise, go to step 13.
Note:
DO NOT use the source release RMD created in Backing Up the Database.Once inserted, allow time for the RMD to be detected by the system.
RMD is inserted in the latched USB port on the active E5-MASP.
- Issue the command to retrieve measurement status.
rtrv-meas-schedResponse to retrieve command is displayed.
Record if collection is on or off:
_____________
Record if system configuration requires measurements to be on or off:
_____________
If COLLECT=ON, continue to next step. Otherwise, go to Step 4.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y COLLECT = off SYSTOT-STP = (off) SYSTOT-TT = (off) COMP-LNKSET = (off) COMP-LINK = (off) MTCD-STP = (on) MTCD-LINK = (on) MTCD-LNKSET = (on) ; - Issue the command to turn off measurement collection.
chg-meas:collect=offResponse to the change command is displayed.
eaglestp YY-MM-DD hh:mm:ss zzzz PPP XX.x.x.x.x-YY.y.y chg-meas:collect=off Command entered at terminal #XX. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CHG-MEAS: MASP A – COMPLTD ; - Issue the command to format the RMD.
FORMAT-DISK:TYPE=SYSTEM:FORCE=YESResponse to format command is displayed.
If the format fails, first repeat the previous step, and then contact My Oracle Support.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Format-disk of system removable cartridge started. Extended processing required, please wait. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Format-disk of system removable cartridge completed. ; - Issue the command to copy the GPLs to the RMD.
COPY-GPLResponse to copy command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y COPY-GPL Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y COPY-GPL: MASP A - COPY STARTS ON ACTIVE MASP ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y COPY-GPL: MASP A - COPY COMPLETED ON ACTIVE MASP ; - Issue the command to report database status.
REPT-STAT-DBResponse to database status command is displayed.
Check entries in ‘C’ should be coherent, which is indicated by a ‘Y’.
If all FD BKUP & FD CRNT entries in column ‘LEVEL’ are the same, go to step 9.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y DATABASE STATUS: >> OK << TDM 1114 ( STDBY) TDM 1116 ( ACTV ) C LEVEL TIME LAST BACKUP C LEVEL TIME LAST BACKUP - -------- ---------------------- - -------- ---------------------- FD BKUP Y XXX YY-MM-DD hh:mm:ss TTTT Y XXX YY-MM-DD hh:mm:ss TTTT FD CRNT Y XXX YY-MM-DD hh:mm:ss TTTT Y XXX YY-MM-DD hh:mm:ss TTTT MCAP 1113 MCAP 1115 - -------- - -------- RD BKUP - - - - N 1 - - USB BKP - - - - - - - - - Issue the database command to backup the fixed disks.
CHG-DB:ACTION=BACKUPResponse and progress of back up command are displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 5028.1114 CARD 1115 Database BACKUP started Report Date:YY-MM-DD Time:hh:mm:ss ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP A - Backup starts on active MASP. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP A - Backup on active MASP to fixed disk complete. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP A - Backup starts on standby MASP. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 5031.1116 CARD 1115 Database action ended - OK Report Date:YY-MM-DD Time:hh:mm:ss ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP A - Backup on standby MASP to fixed disk complete ; - Issue the command to report database status.
rept-stat-dbResponse to database status command is displayed.
Check: entries in C should be coherent, which is indicated by a Y.
Verify both FD CRNT and FD BKUP Levels are equal.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y DATABASE STATUS: >> OK << TDM 1114 ( STDBY) TDM 1116 ( ACTV ) C LEVEL TIME LAST BACKUP C LEVEL TIME LAST BACKUP - -------- ---------------------- - -------- ---------------------- FD BKUP Y XXX YY-MM-DD hh:mm:ss TTTT Y XXX - - FD CRNT Y XXX Y XXX MCAP 1113 MCAP 1115 - -------- - -------- RD BKUP - - - - N 1 - - USB BKP - - - - - - - - ; - Issue the database command to back up to the target-release RMD.
chg-db:action=backup:dest=removeResponse to backup command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 5035.1114 CARD 1115 Database BACKUP started Report Date:YY-MM-DD Time:hh:mm:ss eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (REMOVABLE): MASP B - Backup starts on active MASP. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (REMOVABLE): MASP B - Backup to removable cartridge complete. ; - Issue the command to report database status.
rept-stat-dbResponse to database status command is displayed.
Check entries in C should be coherent, which is indicated by a Y.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y DATABASE STATUS: >> OK << TDM 1114 ( STDBY) TDM 1116 ( ACTV ) C LEVEL TIME LAST BACKUP C LEVEL TIME LAST BACKUP - -------- ---------------------- - -------- ---------------------- FD BKUP Y XXX YY-MM-DD hh:mm:ss TTTT Y XXX YY-MM-DD hh:mm:ss TTTT FD CRNT Y XXX Y XXX MCAP 1113 MCAP 1115 - -------- - -------- RD BKUP - - - - Y XXX YY-MM-DD hh:mm:ss TTTT USB BKP - - - - - - - - - Issue the command to display GPL status.
rtrv-gplResponse from the retrieve command is displayed.
Verify that the GPL versions that are displayed in the RELEASE and REMOVE TRIAL column are correct; see Software Release Numbering.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y GPL Auditing ON GPL CARD RELEASE APPROVED TRIAL REMOVE TRIAL GGGGGG1 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG1 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG1 1113 ----------- ----------- ----------- ----------- GGGGGG2 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG2 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG2 1113 ----------- ----------- ----------- ----------- GGGGGG3 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG3 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG3 1113 ----------- ----------- ----------- ----------- OAMHC 1114 XXX-XXX-XXX XXX-XXX-XXX ----------- ----------- OAMHC 1116 XXX-XXX-XXX XXX-XXX-XXX ----------- ----------- OAMHC 1113 ----------- ----------- ----------- ----------- GGGGGG4 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG4 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG4 1113 ----------- ----------- ----------- ----------- GGGGGG5 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG5 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG5 1113 ----------- ----------- ----------- ----------- GGGGGG6 1114 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX GGGGGG6 1116 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ----------- GGGGGG6 1113 ----------- ----------- ----------- ----------- ; - Remove the target-release RMD from the drive slot.Store the RMD in a safe location.
- If the system is configured for remote backups, issue the database command to
backup to remote FTP server. Otherwise, go to step 14.
chg-db:action=backup:dest=serverResponse to backup command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 5035.1114 CARD 1115 Database BACKUP started Report Date:YY-MM-DD Time:hh:mm:ss eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (SERVER): MASP B - Backup starts on active MASP. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (SERVER): MASP B - Backup to server complete. ; - If step 3 was executed, issue the command to turn the measurements collection
on.
chg-meas:collect=onResponse to change measurement command is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y chg-meas:collect=on Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y CHG-MEAS: MASP A - COMPLTD ;
Upgrade Session 2
Verifying Upgrade Session 2 Requirements
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- Complete pre-upgrade session 2 tasks.Verify that an EAGLE system health check 3 has been performed prior to upgrade session 2 execution.
Upgrading Removable Medias
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- Echo command input to capture terminal. See recommendation #1 & #6 in
Recommendations.
act-echo:trm=P(Where the value for P is one of the printer/KSR terminal port numbers recorded in Verifying Pre-Upgrade Requirements and Capturing Upgrade Data, Step 3)
Response to activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y act-echo:trm=P Command entered at terminal #XX. ; - If capture terminal’s output groups are not all set to YES, issue the change
terminal command.
chg-trm:trm=P:all=yes(P is the terminal port that is specified in step 1)
Response to change terminal command is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y chg-trm:trm=P:all=yes Command entered at terminal #XX. ; - If the measurements platform is enabled[1] go to step 9. Otherwise, issue the
command to retrieve measurement status.
Note:
If enabled, the measurements platform feature is displayed in Procedure 1, Step 11.rtrv-meas-schedResponse to retrieve command is displayed.
Record if collection is on or off:
___________
Record if system configuration requires measurements to be on or off:
___________
If COLLECT=ON, continue to next step. Otherwise, go to Step 9.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y COLLECT = off SYSTOT-STP = (off) SYSTOT-TT = (off) COMP-LNKSET = (off) COMP-LINK = (off) MTCD-STP = (on) MTCD-LINK = (on) MTCD-LNKSET = (on) ; - Issue the command to turn off measurement collection.
chg-meas:collect=offResponse to the change command is displayed.
eaglestp YY-MM-DD hh:mm:ss zzzz PPP XX.x.x.x.x-YY.y.y chg-meas:collect=off Command entered at terminal #XX. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CHG-MEAS: MASP A – COMPLTD ; - Issue measurement report command.
rept-meas:type=systot:enttype=stpResponse to the command is displayed.
If command fails, reattempt in five minutes until it completes, See Table below.
E2278 Cmd Rej: 30-minute measurement collection in progress eaglestp YY-MM-DD hh:mm:ss zzzz PPP XX.x.x.x.x-YY.y.y rept-meas:type=systot:enttype=stp Command entered at terminal #XX. ; - If LNP feature on, issue measurement report command.
Note:
This cmd is not supported in 46.3.rept-meas:type=mtcd:enttype=lnpResponse to the command is displayed.
If command fails, reattempt in five minutes until it completes, See Table below.E2277 Cmd Rej: Daily measurement collection in progress eaglestp YY-MM-DD hh:mm:ss zzzz PPP XX.x.x.x.x-YY.y.y rept-meas:type=mtcd:enttype=lnp Command entered at terminal #XX. ; - Issue measurement report command.
rept-meas:type=mtcdth:enttype=stpResponse to the command is displayed.
If command fails, reattempt in five minutes until it completes, See Table below.
If no source cartridges need upgrading, go to next procedure.
E2276 Cmd Rej: Day-to-hour measurement collection in progress eaglestp YY-MM-DD hh:mm:ss zzzz PPP XX.x.x.x.x-YY.y.y rept-meas:type= mtcdth:enttype=stp Command entered at terminal #XX. ; - Insert the source-release RMD to be upgraded into the drive slot on the active
MASP. Once inserted, allow time for the RMD to be detected by the system.
RMD is inserted in the latched USB port on the active E5-MASP.
- Issue the command to format the RMD.
format-disk:type=system:force=yesResponse to format command is displayed.
If the format should fail, first repeat Step 16, then contact My Oracle Support.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Format-disk of system removable cartridge started. Extended processing required, please wait. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Format-disk of system removable cartridge completed. ; - Issue the command to copy the GPLs to the target-release RMD.
copy-gplResponse to copy command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y copy-gpl Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y COPY-GPL: MASP A - COPY STARTS ON ACTIVE MASP ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y COPY-GPL: MASP A - COPY COMPLETED ON ACTIVE MASP ; - Issue the command to backup the target-release database to the RMD.
chg-db:action=backup:dest=removeResponse to backup command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 5035.1114 CARD 1115 Database BACKUP started Report Date:YY-MM-DD Time:hh:mm:ss ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (REMOVABLE): MASP B - Backup starts on active MASP. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (REMOVABLE): MASP B - Backup to removable cartridge complete. ; - Remove the target-release RMD from the drive slot and store it in a safe
place.If upgrading more RMDs, repeat step 15-22.
Table 5-4 MTT Errors Generated When Measurement Collection is in Progress
Response ID Code: Command Reject Text for MTT error: E2276 Day-to-hour measurement collection in progress E2277 Daily measurement collection in progress E2278 30-minute measurement collection in progress E2279 5-minute measurement collection in progress E2290 Hourly measurement collection in progress E3688 15-minute measurement collection in progress
Backing Up Fixed Disk
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- Issue the command to backup the database to the fixed disks.
chg-db:action=backupResponse and progress of the backup command are displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 5028.1114 CARD 1115 Database BACKUP started Report Date:YY-MM-DD Time:hh:mm:ss ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP A - Backup starts on active MASP. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP A - Backup on active MASP to fixed disk complete. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP A - Backup starts on standby MASP. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 5031.1116 CARD 1115 Database action ended - OK Report Date:YY-MM-DD Time:hh:mm:ss ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y BACKUP (FIXED): MASP A - Backup on standby MASP to fixed disk complete. ;
Migrate the ATMITU or ATMANSI (E5-ATM-B) Cards Running VxWorks 6.4 GPL to VxWorks 6.9 GPL
Note:
Run this procedure if the target release is 46.9.0 and later.Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- If the source release was 46.7.x and later, issue the LIMATM or LIME1ATM-type
card status command. Otherwise, continue to next procedure.
REPT-STAT-CARD:APPL=ATMITUORREPT-STAT-CARD:APPL=ATMANSIResponse to the card status command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST XXXX XXX-XXX-XXX LIMATM ATMHC IS-NR Active ----- XXXX XXX-XXX-XXX LIMATM ATMHC IS-NR Active ----- Command Completed. ; - For each LIMATM or LIME1ATM-type card listed above, issue the GPL status
command.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of a LIMATM or LIME1ATM-type card slot listed in previous step.)
Response to the status command is displayed.
If the “ALM” indictor is displayed for the card’s flash image, continue. If card is running BLMCAP, continue. Otherwise repeat step 2 for next LIMATM or LIME1ATM-type card in list.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y GPL CARD RUNNING APPROVED TRIAL ATMHC XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ZZZZZZ ZZZ-ZZZ-ZZZ ALM YYY-YYY-YYY YYY-YYY-YYY Command Completed. - Issue command to cancel the links on the card.
DACT-SLK:LOC=XXXX:LINK=<LINK NAME>(Where XXXX is the location of the LIMATM or LIME1ATM-type card used in the previous step)
- Issue command to inhibit the card.
INH-CARD:LOC=XXXX(Where XXXX is the location of the LIMATM or LIME1ATM-type card use in previous command.)
Response to the inhibit command is displayed
If the ALM indication was displayed in step 2, continue. Otherwise, go to step 7.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Card has been inhibited. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Command Completed. ;Note:
Wait for the card to boot and return to the IMT bus. - Issue command to download approved flash image.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLMCAP(Where XXXX is the location of the LIMATM or LIME1ATM-type card use in previous command.)
Response to flash initialization is shown.
Verify UAM 0004 is displayed. If card is running BLDC32, go to step 7. Otherwise, continue.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 8003.0004 * GPL SYSTEM ZZZZZZ Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:LOC=XXXX(Where XXXX is the location of the LIMATM or LIME1ATM-type card use in previous command.)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue flash command to download the bootloader image.
INIT-FLASH:LOC=XXXX:MODE=RPLCEBL:BITS=64(Where XXXX is the location of the LIMATM or LIME1ATM-type card use in previous command.)
Response to flash command is shown.
If either response is displayed, then proceed to the next step.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y BOOTLOADER change for card XXXX SUCCESSFUL. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Command Completed. ; OR If the bootloader was succesfully downloaded previously: eaglestp 17-01-20 12:19:04 MST EAGLE XX.x.x.x.x-YY.y.y BOOTLOADER not changed for card XXXX. Already running requested bootloader. ; eaglestp 17-01-20 12:19:04 MST EAGLE XX.x.x.x.x-YY.y.y Command Completed. ; - Download target-release flash to the LIMATM or LIME1ATM-type card.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLDC32(Where XXXX is the location used in the previous command)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y * 8003.0004 * GPL SYSTEM BLDC32 Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:loc=XXXX(Where XXXX is the location of the LIMATM or LIME1ATM-type card used in the previous command)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue the allow command to reload the LIMATM or LIME1ATM-type card.
ALW-CARD:LOC=XXXX(Where XXXX is the location of the card used in the previous command)
Response to allow-card command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Card has been allowed. ; - Retrieve status of the LIMATM or LIME1ATM-type card if present in the
system.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of the card used in the previous command)
Response to GPL status command.
Verify that LIMATM or LIME1ATM-type card is BLDC32 GPL.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y GPL Auditing ON GPL CARD RUNNING APPROVED TRIAL ATMHC69 XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLDC32 YYY-YYY-YYY YYY-YYY-YYY YYY-YYY-YYY Command Completed. ; - Issue command to activate the links.
ACT-SLK:LOC=XXXX:LINK=<LINK NAME>(Where XXXX is the location of the LIMATM or LIME1ATM-type card in Step 3)
- Issue command to report the status of the LIMATM or LIME1ATM-type cards.
REPT-STAT-CARD:APPL=LIMATMORREPT-STAT-CARD:APPL=LIME1ATMResponse to the status command.
Verify that LIMATM or LIME1ATM cards have returned to IS-NR
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST XXXX XXX-XXX-XXX LIMATM ATMHC IS-NR Active ----- XXXX XXX-XXX-XXX LIMATM ATMHC IS-NR Active ----- Command Completed. ; - If this is the last card listed in Step 1, continue to next procedure.
Otherwise, repeat Steps 2 - 13 for the next card listed in Step 1.
Note:
Wait till this flashed LIMATM or LIME1ATM-type card to complete reloading before proceeding to next step.
Migrate the E5-E1T1-B Cards Running VxWorks 6.4 GPL to VxWorks 6.9 GPL
Note:
Run this procedure if the target release is 46.9.0 and later.Execute the below procedure for every LIME1 or LIMT1 E5-E1T1-B card present in the system.
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- If the source release was 46.7.x and later, issue the LIME1 or LIMT1 card
status command. Otherwise, continue to next procedure.
REPT-STAT-CARD:APPL=SS7ANSIORREPT-STAT-CARD:APPL=CCS7ITUResponse to the card status command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST XXXX XXX-XXX-XXX LIME1 SS7HC IS-NR Active ----- XXXX XXX-XXX-XXX LIME1 SS7HC IS-NR Active ----- Command Completed. ; - For each LIME1 or LIMT1 E5-E1T1-B-type card listed above, issue the GPL status
command.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of a LIME1 or LIMT1 E5-E1T1-B card slot listed in previous step.)
Response to the status command is displayed.
If the “ALM” indictor is displayed for the card’s flash image, continue. If card is running BLMCAP, continue. Otherwise repeat step 2 for next LIME1 card in list.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y GPL CARD RUNNING APPROVED TRIAL SS7HC XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX ZZZZZZ ZZZ-ZZZ-ZZZ ALM YYY-YYY-YYY YYY-YYY-YYY Command Completed. - Issue command to cancel the links on the card.
DACT-SLK:LOC=XXXX:LINK=<LINK NAME>(Where XXXX is the location of the LIME1 or LIMT1 E5-E1T1-B card used in the previous step)
- Issue command to inhibit the card.
INH-CARD:LOC=XXXX(Where XXXX is the location of the LIME1 or LIMT1 E5-E1T1-B card use in previous command.)
Response to the inhibit command is displayed
If the ALM indication was displayed in step 2, continue. Otherwise, go to step 7.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Card has been inhibited. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Command Completed. ;Note:
Wait for the card to boot and return to the IMT bus. - Issue command to download approved flash image.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLMCAP(Where XXXX is the location of the LIME1 or LIMT1 E5-E1T1-B card use in previous command.)
Response to flash initialization is shown.
Verify UAM 0004 is displayed. If card is running BLDC32, go to step 7. Otherwise, continue.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 8003.0004 * GPL SYSTEM ZZZZZZ Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:LOC=XXXX(Where XXXX is the location of the LIME1 or LIMT1 E5-E1T1-B card use in previous command.)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue flash command to download the bootloader image.
INIT-FLASH:LOC=XXXX:MODE=RPLCEBL:BITS=64(Where XXXX is the location of the LIME1 or LIMT1 E5-E1T1-B card used in the previous command.)
Response to flash command is shown.
If either response is displayed, then proceed to the next step.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y BOOTLOADER change for card XXXX SUCCESSFUL. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Command Completed. ; OR If the bootloader was succesfully downloaded previously: eaglestp 17-01-20 12:19:04 MST EAGLE XX.x.x.x.x-YY.y.y BOOTLOADER not changed for card XXXX. Already running requested bootloader. ; eaglestp 17-01-20 12:19:04 MST EAGLE XX.x.x.x.x-YY.y.y Command Completed. ; - Download target-release flash to the LIME1 or LIMT1 E5-E1T1-B card.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLDC32(Where XXXX is the location used in the previous command)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y * 8003.0004 * GPL SYSTEM BLDC32 Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:loc=XXXX(Where XXXX is the location of the LIME1 or LIMT1 E5-E1T1-B card used in the previous command)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue the allow command to reload the LIME1 or LIMT1 E5-E1T1-B card.
ALW-CARD:LOC=XXXX(Where XXXX is the location of the card used in the previous command)
Response to allow-card command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Card has been allowed. ; - Retrieve status of the LIME1 or LIMT1 E5-E1T1-B card if present in the
system.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of the card used in the previous command)
Response to GPL status command.
Verify that LIME1 or LIMT1 card is BLDC32 GPL.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y GPL Auditing ON GPL CARD RUNNING APPROVED TRIAL SS7HC69 XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLDC32 YYY-YYY-YYY YYY-YYY-YYY YYY-YYY-YYY Command Completed. ; - Issue command to activate the links.
ACT-SLK:LOC=XXXX:LINK=<LINK NAME>(Where XXXX is the location of the LIME1 or LIMT1 card in Step 3)
- Issue command to report the status of the LIME1 or LIMT1 cards.
REPT-STAT-CARD:APPL=SS7ANSIORREPT-STAT-CARD:APPL=CCS7ITUResponse to the status command.
Verify that LIME1 or LIMT1 cards have returned to IS-NR
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST XXXX XXX-XXX-XXX LIME1 SS7HC IS-NR Active ----- XXXX XXX-XXX-XXX LIME1 SS7HC IS-NR Active ----- Command Completed. ; - If this is the last card listed in Step 1, continue to next procedure.
Otherwise, repeat Steps 2 - 13 for the next card listed in Step 1.
Note:
Wait till this flashed LIME1 or LIMT1 E5-E1T1-B card to complete reloading before proceeding to next step.
CCS7ITU or SS7ANSI Application is Provisioned on SLIC Card, Migrate the Same to VxWorks6.9
Note:
Run this procedure if the target release is 46.9.0 and later.Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- If the source release was 46.7.x and later, issue the LIME1 or LIMT1 card
status command. Otherwise, continue to next procedure.
REPT-STAT-CARD:APPL=SS7ANSIORREPT-STAT-CARD:APPL=CCS7ITUResponse to the card status command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST XXXX XXX-XXX-XXX LIME1 SS7HC IS-NR Active ----- XXXX XXX-XXX-XXX LIME1 SS7HC IS-NR Active ----- Command Completed. ; - For each card with type equal to LIME1 or LIMT1 listed above, issue the GPL
status commend.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location of a LIME1 or LIMT1 SLIC card slot listed in previous step.)
Response to the GPL status command is displayed.
If the ALM indictor is displayed for the card’s flash image, continue. If card is running BLSLC32, continue.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x-YY.yy.y GPL CARD RUNNING APPROVED TRIAL SS7HC XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLSLC32 ZZZ-ZZZ-ZZZ ALM YYY-YYY-YYY YYY-YYY-YYY Command Completed. - Issue command to cancel the links on the card.
DACT-SLK:LOC=XXXX:LINK=<LINK NAME>(Where XXXX is the location of the LIME1 or LIMT1 SLIC card used in the previous step)
- Issue command to inhibit the card.
INH-CARD:LOC=XXXX(Where XXXX is the location of the LIME1 or LIMT1 SLIC card)
Response to the inhibit command is displayed
If the ALM indication was displayed in step 2, continue. Otherwise, go to step 7.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Card has been inhibited. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Command Completed. ;Note:
Wait for the card to boot and return to the IMT bus. - Issue command to download approved flash image.
INIT-FLASH:LOC=XXXX:CODE=APPR(Where XXXX is the location of the LIME1 or LIMT1 SLIC card use in previous command.)
Response to flash initialization is shown. Verify UAM 0004 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 8003.0004 * GPL SYSTEM ZZZZZZ Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:LOC=XXXX(Where XXXX is the location of the LIME1 or LIMT1 SLIC card use in previous command.)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Activation for card XXXX Completed. ; - Issue update bootloader command.
INIT-FLASH:LOC=XXXX:MODE=RPLCEBL:BITS=64 - Issue flash command to download target-release flash to the LIME1 or LIMT1
SLIC card.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLSL932(Where XXXX is the location used in the previous command)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y * 8003.0004 * GPL SYSTEM BLSL932 Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash image.
ACT-FLASH:LOC=XXXX(Where XXXX is the location of the LIME1 or LIMT1 SLIC card used in the previous command)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue the allow command to reload the LIME1 or LIMT1 SLIC card.
ALW-CARD:LOC=XXXX(Where XXXX is the location of the card used in the previous command)
Response to allow-card command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Card has been allowed. ; - Issue command to report GPL status.
REPT-STAT-GPL:LOC=XXXXResponse to GPL status command.
Verify that LIME1 or LIMT1 SLIC card is running BLSL932 GPL.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y GPL Auditing ON GPL CARD RUNNING APPROVED TRIAL SS7HC69 XXXX XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX BLSL932 YYY-YYY-YYY YYY-YYY-YYY YYY-YYY-YYY Command Completed. ; - Issue command to activate the links.
ACT-SLK:LOC=XXXX:LINK=<LINK NAME>(Where XXXX is the location of the LIME1 or LIMT1 card in Step 3)
- Issue command to report the status of the LIME1 or LIMT1 cards.
REPT-STAT-CARD:APPL=SS7ANSIORREPT-STAT-CARD:APPL=CCS7ITUResponse to the status command.
Verify that LIME1 or LIMT1 cards have returned to IS-NR
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST XXXX XXX-XXX-XXX LIME1 SS7HC IS-NR Active ----- XXXX XXX-XXX-XXX LIME1 SS7HC IS-NR Active ----- Command Completed. ; - If this is last card listed in Step 1, continue to next procedure. Otherwise,
repeat Steps 2 - Step 13 for the next card listed in Step 1.
Note:
Wait till this flashed LIME1 or LIMT1 card to complete reloading before proceeding to next step.
Upgrading Spare MASPs
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- Issue the command to display card status.
REPT-STAT-CARD:APPL=OAMResponse to the card status command is displayed.
Determine MASP activity.
Act MASP __________
Stby MASP _________
CARD VERSION TYPE GPL PST SST AST 1113 XXX-XXX-XXX E5MCAP OAMHC IS-NR Standby ----- 1115 XXX-XXX-XXX E5MCAP OAMHC IS-NR Active ----- Command Completed. ; - Issue the command to inhibit standby MASP.
INH-CARD:LOC=XXXX(Where XXXX is the location for the Standby MASP in the previous steps.)
Response to the command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Card has been inhibited. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Command Completed. ; - Place spare E5-MASP in system.Slide the MASP H/S switch (SW3) on the standby MASP up to the unlocked position (Wait for all drive LEDs to transition to a steady blue).
Remove the standby E5-MASP card determined in step 2.
Insert the spare E5-MASP card.
Slide the MASP H/S switch (SW3) on the new standby MASP down to the locked position (Wait for the MASP H/S LED to transition from blinking blue to off and the MASP to come up in standby mode).
Note:
UAMs are generated during this step. An audible alarm is generated. Wait for the new standby MASP to come up in standby mode and system returns to duplex mode. - Issue command to report the GPLs running on the card location.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location for the Standby MASP recorded Step 1.)
Response to the status command is displayed.
If the ALM indicator is displayed for the card’s flash image, continue. If the target release is 46.6 or higher and the card is running BLMCAP, continue. Otherwise, go to step 20.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y GPL CARD RUNNING APPROVED TRIAL GGGGG XXXX ----------- ----------- ----------- BLMCAP YYY-YYY-YYY ALM XXX-XXX-XXX YYY-YYY-YYY Command Completed. ; - Download the approved version flash to the standby MASP.
INIT-FLASH:LOC=XXXX:CODE=APPR(Where XXXX is the location of the standby MASP slot used in the previous command.)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
If the target release is 46.6 or higher and the card is running BLMCAP, continue. Otherwise, go to step 18.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 8003.0004 * GPL SYSTEM ZZZZZZ Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Issue command to activate the flash on standby MASP
ACT-FLASH:loc=XXXX(Where XXXX is the location of the standby MASP used in the previous command)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for card XXXX Completed. ; - Issue flash command to download the bootloader image.
INIT-FLASH:LOC=XXXX:MODE=RPLCEBL:BITS=32(Where XXXX is the location of the standby MASP slot used in the previous command.)
Response to flash command is shown.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 BOOTLOADER change for card XXXX SUCCESSFUL. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y Upg Phase 3 Command Completed. ; - Issue command to download approved BLDC32 flash image.
INIT-FLASH:LOC=XXXX:CODE=APPR:GPL=BLDC32(Where XXXX is the location used in the previous command)
Response to flash initialization is shown.
Verify UAM 0004 is displayed.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx started. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y FLASH Memory Download for card xxxx completed. ; eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y 8003.0004 * GPL SYSTEM BLDC32 Card is running non-activated GPL ;Note:
Wait for card to boot and return to the IMT bus. - Retrieve the GPLs running on the card location.
REPT-STAT-GPL:LOC=XXXX(Where XXXX is the location used in the previous command)
Response to the GPL status command is displayed.
Verify that card is running BLDC32 GPL.
eaglestp YY-MM-DD hh:mm:ss TTTT EAGLE XX.x.x.x.x-YY.y.y GPL CARD RUNNING APPROVED TRIAL OAMHC XXXX ----------- ----------- ----------- BLDC32 YYY-YYY-YYY+ YYY-YYY-YYY XXX-XXX-XXX Command Completed. ; - Activate the flash on standby MASP.
ACT-FLASH:loc=XXXX(Where XXXX is the location of the standby MASP used in the previous command)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Memory Activation for card XXXX Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Upg Phase 3 FLASH Activation for card XXXX Completed. ; - Insert target-release USB into the drive slot on the standby E5-MASP. Once inserted, allow time for the RMD to be detected by the system.
- Issue the command to allow card.
alw-card:loc=XXXXWhere XXXX is the location for the Standby MASP.
Response to the command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Card has been allowed. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Command Completed. ; - Issue the command to display MASP status.
rept-stat-card:appl=oamResponse to the card status command is displayed.
Verify the MASP cards are running the same version of the OAM application GPL.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y CARD VERSION TYPE GPL PST SST AST 1113 XXX-XXX-XXX TTTTT GGGG IS-NR ACTIVE ---- 1115 XXX-XXX-XXX TTTTT GGGG IS-NR STANDBY ---- Command Completed. ; - Issue the command to display security log status.
rept-stat-seculogResponse to the command is displayed.
If the ENTRIES column displays any value other than 0 for the Standby ROLE, proceed to the next step. Otherwise, go to step 34.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y rept-stat-seculog Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y -- SINCE LAST UPLOAD -- OLDEST NEWEST LAST LOC ROLE ENTRIES %FULL OFLO FAIL RECORD RECORD UPLOAD 1114 Active 19 1 No No 99-01-01 99-01-01 00-00-00 13:43:37 14:08:12 00:00:00 1116 Standby 0 0 No No 99-01-01 99-01-01 99-01-01 13:39:39 13:43:10 14:07:59 ; - Issue the command to copy the security log from the standby disk to FTA
area.
copy-seculog:slog=stb:dfile=upgP15.sprResponse to copy seculog command is displayed.
If this command fails, proceed to next step. Otherwise, go to step 34.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Security log on TDM 111X copied to file upgP15.spr on TDM 111Y ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 0468.0177 SECULOG 111X Security log exception cleared ; - Issue the command to display the FTA directory.
disp-fta-dirResponse to display directory command is displayed.
If there are any files that need to be saved, they need to be removed via a file transfer.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y File Transfer Area Directory of fixed disk 111Y FILENAME LENGTH LAST MODIFIED LBA YYMMDDs.log 2560256 99-01-03 10:18:44 388769 YYMMDDa.log 2560256 99-01-03 10:19:20 393770 m60_lnp.csv 0 99-01-03 13:10:38 398771 3 File(s) 21093376 bytes free ; - Issue the command to delete ALL files in the transfer area
dlt-fta:all=yesResponse to the delete command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y dlt-fta:all=yes Command entered at terminal #nn. ; - Repeat Steps 27-28.
- Issue the command to copy the active MASP image to the standby disk.
copy-disk:dloc=XXXX:force=yes:format=yes(Where XXXX is the location of the STANDBY E5-TDM recorded in Step 2)
Response to the copy-disk command is displayed.
Note that user terminal port may be automatically logged out.
Wait for the card reload to complete.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Copy-disk (fixed): from active (YYYY) to standby (XXXX) started. Extended processing required, please wait. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Copy-disk (fixed): from active (YYYY) to standby (XXXX) complete. Measurements may be allowed now if desired. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 0485.0014 CARD 1115 OAMHC Card is present ; - If the disk copy fails repeat steps 34-35.
- Repeat Steps 34-35.
- If second attempt fails, contact My Oracle Support
- If the measurements platform is enabled then go next procedure. Otherwise, if
Procedure 17 Steps 7 & 8 were executed, issue the command to turn the
measurements collection on.
CHG-MEAS:COLLECT=ONResponse to change measurement command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y chg-meas:collect=on Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CHG-MEAS: MASP A - COMPLTD ;
Upgrading Spare HIPR2 Cards
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- Issue the command to display imt bus status.
rept-stat-muxResponse to the
MUX statuscommand is displayed.eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD TYPE PST SST AST BITRATE 1109 HIPR2 IS-NR Active ----- HIGH 1110 HIPR2 IS-NR Active ----- HIGH 1209 HIPR2 IS-NR Active ----- HIGH 1210 HIPR2 IS-NR Active ----- HIGH 1309 HIPR2 IS-NR Active ----- HIGH 1310 HIPR2 IS-NR Active ----- HIGH Command Completed. ; - Issue the command to display imt bus status.
rept-stat-imtResponse to the card status command is displayed.
Verify that both imt buses are IS-NR.
If either bus is not IS-NR Stop this procedure and contact My Oracle Support
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y rept-stat-imt Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y IMT PST SST AST A IS-NR Active ----- ALARM STATUS = No Alarms. IMT PST SST AST B IS-NR Active ----- ALARM STATUS = No Alarms. Command Completed. ; - Issue the command to initialize the IMT bus B at low speed only if the HIPR2
card is getting upgraded from R46.3 or earlier to R46.4 or higher. Otherwise, go
to step 6.
init-mux:bus=b:hs=noResponse to the above command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y init-mux:bus=b:hs=no Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Command Completed. ; - Issue the command to display imt bus status.
rept-stat-muxResponse to the MUX status command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD TYPE PST SST AST BITRATE 1109 HIPR2 IS-NR Active ----- HIGH 1110 HIPR2 IS-NR Active ----- LOW 1209 HIPR2 IS-NR Active ----- HIGH 1210 HIPR2 IS-NR Active ----- LOW 1309 HIPR2 IS-NR Active ----- HIGH 1310 HIPR2 IS-NR Active ----- LOW Command Completed. ; - Issue the command to display imt bus status
rept-stat-imtResponse to the card status command is displayed.
Verify that both imt buses are IS-NR.
If either bus is not IS-NR Stop this procedure and contact My Oracle Support
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y rept-stat-imt Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y IMT PST SST AST A IS-NR Active ----- ALARM STATUS = No Alarms. IMT PST SST AST B IS-NR Active ----- ALARM STATUS = No Alarms. Command Completed. ; - Issue the command to inhibit IMT bus-B.
inh-imt:bus=bResponse to the command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Inhibit IMT Bus B command issued ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 8687.0098 IMT BUS B IMT inhibited ; - Swap spare HIPR2 cards with those on the IMT B-bus. (i.e. location 1110, 1210)
- Issue the command to allow IMT bus-B.
alw-imt:bus=bResponse to the command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Allow IMT Bus B command issued ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 8712.0097 IMT BUS B IMT allowed ; - Issue the command to display imt bus status.
rept-stat-muxResponse to the MUX status command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD TYPE PST SST AST BITRATE 1109 HIPR2 IS-NR Active ----- HIGH 1110 HIPR2 IS-NR Active ----- LOW 1209 HIPR2 IS-NR Active ----- HIGH 1210 HIPR2 IS-NR Active ----- LOW 1309 HIPR2 IS-NR Active ----- HIGH 1310 HIPR2 IS-NR Active ----- LOW Command Completed. ; - Issue the command to display imt bus status.
rept-stat-imtResponse to the card status command is displayed.
Verify that both imt buses are IS-NR.
If either bus is not IS-NR Stop this procedure and contact My Oracle Support.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y rept-stat-imt Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y IMT PST SST AST A IS-NR Active ----- ALARM STATUS = No Alarms. IMT PST SST AST B IS-NR Active ----- ALARM STATUS = No Alarms. Command Completed. ; - Issue the card status command to identify the MUX cards in the system.
rept-stat-gpl:gpl=hipr2Response to the command is displayed.
Record the CARD locations for all MUX cards in the system not running the APPROVED version of the GPL.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y GPL Auditing ON APPL CARD RUNNING APPROVED TRIAL HIPR2 XX09 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX10 YYY-YYY-YYY ALM XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX09 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX10 YYY-YYY-YYY ALM XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX09 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX10 YYY-YYY-YYY ALM XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX09 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX10 YYY-YYY-YYY ALM XXX-XXX-XXX XXX-XXX-XXX Command Completed. ; - Enter the command to initialize the FLASH on a MUX card on the B-bus that is
not running the APPROVED version of the GPL.
init-flash:sloc=1110:eloc=XX10:code=appr:gpl=hipr2(Where XX = is a last shelf number with a spare MUX being flashed.)
Response to the flash initialization is shown.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y init-flash:loc=XX10:code=appr:gpl=hipr2 Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Download for card XX10 Started. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Download for card XX10 Completed. ; - Enter the command to initialize the current bus.
init-mux:bus=bResponse to the initialization command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 5080.0014 CARD XX10 HIPR2 Card is present ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y 5081.0014 CARD YY10 HIPR2 Card is present ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y * 5082.0004 * GPL SYSTEM HIPR2 Card is running non-activated GPL - Issue the command to display imt bus status.
rept-stat-muxResponse to the MUX status command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y CARD TYPE PST SST AST BITRATE 1109 HIPR2 IS-NR Active ----- HIGH 1110 HIPR2 IS-NR Active ----- HIGH 1209 HIPR2 IS-NR Active ----- HIGH 1210 HIPR2 IS-NR Active ----- HIGH 1309 HIPR2 IS-NR Active ----- HIGH 1310 HIPR2 IS-NR Active ----- HIGH Command Completed. ; - Issue the command to display imt bus status.
rept-stat-imtResponse to the card status command is displayed.
Verify that both imt buses are IS-NR.
If either bus is not IS-NR Stop this procedure and contact My Oracle Support.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y rept-stat-imt Command entered at terminal #10. ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y IMT PST SST AST A IS-NR Active ----- ALARM STATUS = No Alarms. IMT PST SST AST B IS-NR Active ----- ALARM STATUS = No Alarms. Command Completed. ; - Issue the command to activate the flash on a MUX card flashed in step 12.
act-flash:sloc=1110:eloc=XX10:gpl=hipr2(Where XX is a last shelf number with spare MUX being flashed)
Response to the activate command is displayed.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Memory Activation for card 1110-XX10 Started. ; XX.x.x.x.x-YY.y.y eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y * 2395.0002 * GPL SYSTEM HIPR2 Card is not running approved GPL ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y FLASH Activation for cards 1110 - XX10 completed. LOC YY10 : FLASH OPERATION COMPLETED LOC XX10 : FLASH OPERATION COMPLETED ALL CARD RESULTS PASSED ; eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y Command Completed. ; - Issue the command to display the HIPR2 card GPL status.
rept-stat-gpl:gpl=hipr2Verify that all HIPR2 cards are running the approved GPL.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y GPL Auditing ON APPL CARD RUNNING APPROVED TRIAL HIPR2 XX09 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX10 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX09 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX10 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX09 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX10 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX09 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX HIPR2 XX10 XXX-XXX-XXX XXX-XXX-XXX XXX-XXX-XXX Command Completed. ; - Repeat steps 1-17 until all spare HIPR2 cards have been flashed.
Verifying All Databases
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- Issue the command to display database information.
rept-stat-db:display=allResponse to the command is displayed.
Look in the columns labeled C, T, and LEVEL output by this command.
Verify entries in column C show Y, which indicates coherence.
Verify entries in column T show N (except the E5-MDAL), which indicates that the database is not in transition.
Verify all entries in the database LEVEL column are the same.
LEVEL is a value, which varies depending on the system.
If the STDBY databases are not coherent or not at the correct level, repeat Updating the Source-Release Spare Fixed Disk, step 8.
Verify that the MPS databases are coherent.
eaglestp YY-MM-DD hh:mm:ss TTTT PPP XX.x.x.x.x-YY.y.y DATABASE STATUS: >> OK << TDM 1114 ( ACTV ) TDM 1116 ( STDBY) C LEVEL TIME LAST BACKUP C LEVEL TIME LAST BACKUP - -------- ---------------------- - -------- ---------------------- FD BKUP Y YYY YY-MM-DD hh:mm:ss TTTT Y YYY YY-MM-DD hh:mm:ss TTTT FD CRNT Y XXX Y XXX MCAP 1113 MCAP 1115 - -------- - -------- RD BKUP - - - - Y YYY YY-MM-DD hh:mm:ss TTTT USB BKP - - - - - - - - CARD/APPL LOC C T LEVEL TIME LAST UPDATE EXCEPTION --------- ---- - - ---------- ----------------- -------------- SS7ANSI 1101 Y N XXX 06-04-19 12:13:02 - SS7ANSI 1103 Y N XXX 06-04-19 12:13:02 - GLS 1104 Y N XXX 06-04-19 12:13:02 - SS7ANSI 1105 Y N XXX 06-04-19 12:13:02 - SS7ANSI 1106 Y N XXX 06-04-19 12:13:02 - VSCCP 1107 Y N XXX 06-04-19 12:13:02 - VSCCP 1111 Y N XXX 06-04-19 12:13:02 - OAM-RMV 1113 - - - - - - TDM-CRNT 1114 Y N XXX 06-04-19 12:13:02 - TDM-BKUP 1114 Y - YYY 06-04-18 16:11:18 DIFF LEVEL OAM-RMV 1115 Y - YYY 06-04-18 16:11:18 DIFF LEVEL OAM-USB 1115 - - - - - - TDM-CRNT 1116 Y N XXX 06-04-19 12:13:02 - TDM-BKUP 1116 Y - YYY 06-04-18 16:11:18 DIFF LEVEL E5MDAL 1117 Y - YYY 06-04-18 16:11:18 DIFF LEVEL EPAP A ( ACTV ) C BIRTHDATE LEVEL EXCEPTION - ----------------- ---------- -------------- PDB 03-09-04 15:09:38 418231879 - RTDB Y 03-09-04 15:09:38 418231879 - RTDB-EAGLE 06-02-06 22:13:06 418231879 - EPAP B ( STDBY ) C BIRTHDATE LEVEL EXCEPTION - ----------------- ---------- -------------- PDB 03-09-04 15:09:38 418231879 - RTDB Y 03-09-04 15:09:38 418231879 - RTDB-EAGLE 06-02-06 22:13:06 418231879 - EAGLE RTDB REPORT CARD/APPL LOC C BIRTHDATE LEVEL EXCEPTION IN-SRVC --------- ---- - ----------------- ---------- ------------ ----------- VSCCP 1107 Y 06-02-06 22:13:06 418231879 - 0d 4h 33m VSCCP 1111 Y 06-02-06 22:13:06 418231879 - 0d 4h 33m ; - When the command completes, remove the target-release RMD from the drive
slot.Store the RMD in a safe location.
Session 2 Completion
Should THIS PROCEDURE FAIL, CONTACT My Oracle Support AND ASK FOR UPGRADE ASSISTANCE.
- Issue status command for troubles.
rept-stat-trblResponse to command is displayed.
If UAM 0002 is present where XXXX is a flash GPL (i.e. BLMCAP or BLIXP), record it below:
______________
______________
If any GPL is recorded contact My Oracle Support and report the GPL alarm.
eaglestp YY-MM-DD hh:mm:ss EST PPP XX.x.x.x.x-YY.y.y SEQN UAM AL DEVICE ELEMENT TROUBLE TEXT 0329.0048 * TERMINAL 15 Terminal failed 0330.0048 * TERMINAL 16 Terminal failed 0006.0002 * GPL SYSTEM XXXX Card is not running approved GPL 0331.0176 * SECULOG 1116 Stdby security log—upload required 0332.0308 *C SYSTEM Node isolated due to SLK failures Command Completed. ;