4.75 chg-gttset
Use this command to specify the attributes to change for an existing set of global title translations.
Parameters
- gttsn (mandatory)
- GTT set name. A GTT set is an entity to which global title addresses and selectors are assigned.
- checkmulcomp (optional)
- This option indicates whether or not to find translation for multiple components (up to 3 components, if present) of a TCAP message.
- gttsetmeasrqd (optional)
- GTTSET Measurement required. This parameter specifies whether to perform per GTTSET measurements.
- ndgt (optional)
- Number of digits. The number of digits required for GTAs associated with this GTT set.
- netdom (optional)
- Network domain. This command does not distinguish
between ITU national or ITU international because the Enhanced Global Title
Translation (EGTT) feature does not discriminate between the ITU-I and ITU-N
translations.
Note:
The netdom parameter refers to the incoming message network domain.
Example
chg-gttset:gttsn=lidb:netdom=cross
chg-gttset:gttsn=setxyz:netdom=cross:ndgt=10
chg-gttset:gttsn=acdgta:ngttsn=acdgta1
chg-gttset:gttsn=imsi1:npsn=imsi
chg-gttset:gttsn=setopcode:checkmulcomp=on
chg-gttset:gttsn=setabc:gttsetmeasrqd=pertrans
chg-gttset:gttsn=opcode1:sxudt=no
Dependencies
The (n)gttsn=none parameter cannot be specified.
The specified netdom parameter value must be cross. This command cannot be used to change the netdom setting from cross to ansi or itu.
If the settype parameter has a value of cdssn, cgpc, cgssn, opc, opcode, or dpc, then the ndgt parameter cannot be specified.
The EGTT feature must be turned on prior to using this command.
The value specified for the gttsn parameter must match the name of an existing GTT Set.
If the VGTT feature is turned on, the ndgt parameter cannot be specified.
The ANSI/ITU SCCP Conversion feature must be enabled before the netdom parameter can be specified.
If GTAs are assigned to the GTT set, the ndgt parameter cannot be specified.
The netdom=cross parameter can be specified if the settype=cdgta/imei/imsi/msisdn/vlrnb/smrpoa/smrpda parameter is specified.
The GTTSET table must be accessible.
The GTT DBMM table must be accessible.
The NPSN parameter will be specified with IMEI/IMSI/MSISDN/VLRNB/SMRPOA/SMRPDA GTT set types.
The NPSN parameter can be of MBR set type only.
The value specified for the npsn parameter must match the name of an existing GTT Set of IMEI/IMSI/MSISDN/VLRNB/SMRPOA/SMRPDA types.
The GTT set type of GTT set entry referred by the NPSN parameter should be different from the GTT set type referred by the GTTSN parameter.
The GTT set specified by the gttsn parameter must not be associated with the GTT set referred by the NPSN parameter.
The GTTSET domain and the associated NPSN set domain must match, when the SCCP conversion feature is not ON.
CHECKMULCOMP parameter can be specified with OPCODE GTT set types only.
The SXUDT parameter must be specified with the OPCODE GTT set type only.
Output
chg-gttset:gttsn=acdgta:ngttsn=acdgta1
tekelecstp 10-04-28 17:58:38 EST Eagle 42.0.0
GTT-SET table is (1 of 2000) 1% full.
CHG-GTTSET: MASP A - COMPLTD
;
chg-gttset:gttsn=msisdn:npsn=smrpoa1
tekelecstp 15-05-28 17:58:38 EST Eagle 46.3.0
GTT-SET table is (1 of 2000) 1% full.
CHG-GTTSET: MASP A - COMPLTD
;
chg-gttset:gttsn=setopcode:checkmulcomp=on
tekelecstp 16-10-10 13:54:11 MST EAGLE 46.5.0.0.0-70.5.0
CHG-GTTSET: MASP A - COMPLTD
;
chg-gttset:gttsn=imei12:gttsetmeasrqd=yes
tekelecstp 17-05-11 15:30:38 EST Eagle 46.6.0
GTT-SET table is (1 of 10000) 1% full.
CHG-GTTSET: MASP A - COMPLTD
;
chg-gttset:gttsn=opcode1:sxudt=yes
tekelecstp 17-07-15 14:28:38 EST Eagle 46.6.0
GTT-SET table is (3 of 10000) 1% full.
CHG-GTTSET: MASP A - COMPLTD
;
Related Topics