4.309 ent-gttset
Use this command to specify the attributes of a new GTT set (a set of global title translations). A GTT set consists of a GTT set name, the number of digits allocated for the GTA (global title address), the domain of the point codes used in the translation, and a pointer to a GTA tree. After the GTT set is provisioned, you can enter subsequent GTT Selector commands and GTA commands.
Parameters
- gttsn (mandatory)
- GTT set name. A GTT set is an entity to which global title addresses and selectors are assigned.
- netdom (mandatory)
- Network domain. This command does not distinguish
between ITU national or ITU international because the Enhanced Global Title
Translation (EGTT) feature does not discriminate between the ITU-I and ITU-N
translations.
This parameter refers to the incoming message network domain.
- checkmulcomp (optional)
- This option indicates whether or not to find translation for multiple components (up to 3 components, if present) of a TCAP message.
- gttsetmeasrqd (optional)
- GTTSET Measurement required. This parameter specifies whether to perform per GTTSET measurements.
- ndgt (optional)
- Number of digits. This parameter specifies the number of digits required for GTAs associated with the GTT set.
- npsn (optional)
- GTT set name (Not Present Set Name). This parameter can have IMEI/IMSI/MSISDN/VLRNB/SMRPOA/SMRPDA GTT set types.
Example
ent-gttset:gttsn=lidb:ndgt=10:netdom=ansient-gttset:gttsn=t800:netdom=ansi
ent-gttset:gttsn=setint000:netdom=itu:ndgt=15
ent-gttset:gttsn=setcdgt:netdom=cross:ndgt=10:settype=cdgta
ent-gttset:gttsn=setcggt:netdom=ansi:ndgt=11:settype=cggta
ent-gttset:gttsn=setxyz:netdom=ansi:ndgt=11:settype=cggta
ent-gttset:gttsn=setopc:netdom=itu:settype=opc
ent-gttset:gttsn=setcgpc:netdom=ansi:settype=cgpc
ent-gttset:gttsn=setssn:netdom=ansi:settype=cgssn
ent-gttset:gttsn=setopcode:settype=opcode
ent-gttset:gttsn=setcdssn:netdom=ansi:settype=cdssn
ent-gttset:gttsn=setdpc:netdom=ansi:settype=dpc
ent-gttset:gttsn=imsi1:settype=imsi:netdom=itu
ent-gttset:gttsn=msisdn1:settype=msisdn:npsn=imsi1:netdom=itu
ent-gttset:gttsn=setopcode:settype=opcode:netdom=itu:checkmulcomp=on
ent-gttset:gttsn=imei1:settype=imei:netdom=itu
ent-gttset:gttsn=imsi1:settype=imsi:netdom=itu:gttsetmeasrqd=pertrans
ent-gttset:gttsn=op1:settype=opcode:netdom=itu:sxudt=yes
Dependencies
The EGTT feature must be turned on before this command can be entered.
The GTT Set table cannot contain more than 2000 entries.
The gttsn=none parameter cannot be specified.
If the VGTT (Variable Length GTT) feature is turned on, the ndgt parameter cannot be specified.
The gttsn parameter must be specified and must not match an existing gttsn.
The GTT Set table must be accessible.
The GTT DBMM table must be accessible.
If the settype parameter has a value of cgssn, opc, cgpc, cdssn, opcode, or dpc, then the ndgt parameter cannot be specified.
The netdom=cross parameter can be specified if the settype=cdgta/imei/imsi/msisdn/vlrnb/smrpoa/smrpda parameter is specified.
The Origin-based SCCP Routing feature must be turned on if the value of the settype parameter is cggta, cgssn, opc, or cgpc.
If the OBSR feature is enabled or the FLOBR feature is turned on, then the settype parameter must be specified.
The ANSI/ITU SCCP Conversion feature must be enabled before the netdom=cross parameter can be specified.
The TOBR feature must be turned on before the settype=opcode/imei/imsi/msisdn/vlrnb/smrpoa/smrpda parameter can be specified.
The OBSR feature must be enabled or the FLOBR feature must be turned on before the settype parameter can be specified and before more than 950 GTT set entries can be provisioned.
The FLOBR feature must be turned on before a value of cdssn or dpc can be specified for the settype parameter.
The NPSN parameter must be specified with the IMEI/IMSI/MSISDN/VLRNB/SMRPOA/SMRPDA GTT set types.
NPSN must be of MBR set type only.
The GTT set type of the GTT set entry referred to by the NPSN parameter should be different from the GTT set type referred to by the GTTSN parameter.
The value specified for the NPSN parameter must match the name of an existing GTT set of IMEI/IMSI/MSISDN/VLRNB/SMRPOA/SMRPDA set types.
The GTTSET domain and associated NPSN set domain must match when the SCCP conversion feature is not ON.
CHECKMULCOMP parameter can be specified with OPCODE GTT set types only.
The SXUDT parameter must be specified with the OPCODE GTT set type only.
Notes
When the Origin-based SCCP Routing feature is turned on, VGTT is supported only for CdPA GTA and CgPA GTA. The cross network domain is supported for CdPA GTA and IMEI/IMSI/MSISDN/VLRNB/SMRPOA/SMRPDA GTT set type entries.
Output
ent-gttset:gttsn=setcdssn:netdom=ansi:settype=cdssn
tekelecstp 10-03-12 18:28:54 EST EAGLE 42.0.0
ENT-GTTSET: MASP A - COMPLTD
GTT-SET table is (3 of 2000) 1% full.
;
ent-gttset:gttsn=setimsi:netdom=itu:settype=imsi:npsn=msisdn
tekelecstp 15-06-12 18:28:54 EST EAGLE 46.3.0
ENT-GTTSET: MASP A - COMPLTD
GTT-SET table is (3 of 2000) 1% full.
;
ent-gttset:gttsn=setopcode:settype=opcode:netdom=itu:checkmulcomp=on
tekelecstp 16-10-10 13:54:11 MST EAGLE 46.5.0.0.0-70.5.0
ENT-GTTSET: MASP A - COMPLTD
;
ent-gttset:gttsn=imei1:netdom=itu:settype=imei:gttsetmeasrqd=yes
tekelecstp 17-05-11 15:30:34 EST EAGLE 46.6.0
ENT-GTTSET: MASP A - COMPLTD
GTT-SET table is (3 of 10000) 1% full.
;
ent-gttset:gttsn=opcode1:netdom=itu:settype=opcode:sxudt=yes
tekelecstp 17-07-15 15:22:17 EST EAGLE 46.6.0
ENT-GTTSET: MASP A - COMPLTD
GTT-SET table is (5 of 10000) 1% full.
;
Related Topics