4.308 ent-gttsel
Use this command to assign applicable global title
selectors to a GTT set for enhanced global title translations. If the EGTT
feature is turned on, then the GTT Selector (ent/chg/dlt/rtrv-gttsel
), GTT Set (ent/dlt/rtrv-gttset
), and GTA (ent/chg/dlt/rtrv-gta
) commands replace the Translation
Type (ent/dlt/rtrv-tt
) and Global Title
Translation (ent/chg/dlt/rtrv-gtt
) commands.
However, the Translation Type and Global Title Translation commands continue to
work according to their original functionality when the EGTT feature is on.
Parameters
Note:
The nature of address indicator parameters (naiv or nai) and the numbering plan parameters (npv or np) can be specified using a mnemonic or an explicit value. Either the mnemonic or the explicit value can be specified: however, both values cannot be specified at the same time for the same parameter. NAIV/NAI Mapping shows the mapping between the naiv and nai values. NPV/NP Mapping shows the mapping between the npv and np values.- gti/gtia/gtii/gtin/gtin24/gtiis/gtins/gtin16 (mandatory)
- Global title indicator.
For all EGTT selector commands, the domain is defined as GTI and GTIA (ANSI), GTII (ITU international), GTIN (ITU national), GTIN24 (24-bit ITU national), GTIIS (ITU international spare), GTINS (ITU national spare) and GTIN16 (16-bit ITU National).
For the selector commands, gti and gtia are equivalent. GTT selectors can be provisioned for the same translation type (TT) with different ITU domains. GTT selectors are provisioned independently for each domain. For example, if an entry with gtii=2 and tt=4 already exists, an entry with gtin=2 and tt=4 can be specified.
- eaglegen (optional)
- This parameter specifies whether the selector is used by EAGLE generated messages.
- gttsn (optional)
- GTT set name. A GTT set is an entity to which global title addresses and selectors are assigned.
Example
ent-gttsel:gti=0:cdgttsn=acdgta
ent-gttsel:gtia=2:tt=10:gttsn=t800
ent-gttsel:gtia=2:tt=253:gttsn=setans253
ent-gttsel:gtii=4:tt=0:np=e164:nai=intl:gttsn=setint000
ent-gttsel:gtii=2:tt=0:gttsn=setint000
ent-gttsel:gtin=4:tt=9:np=e214:nai=natl:gttsn=imsi
ent-gttsel:gtii=4:tt=0:np=e164:nai=sub:gttsn=setint000
ent-gttsel:gtia=2:tt=20:cdgtasn=setcdgta:
cggtasn=setcggta:cgssn=10:selid=0
ent-gttsel:gtia=2:tt=21:cggttsn=setcgpc:cdgttsn=setcdgta:
cgssn=20:selid=1:lsn=ls10
ent-gttsel:gtii=2:tt=40:cdgtasn=setcdgta:cgpcsn=setcgpc:cgssn=12
ent-gttsel:gtii=2:tt=41:cgpcsn=setcgpc:cgssn=255:selid=65534
ent-gttsel:gtin=4:tt=60:npv=5:naiv=5:cdgtasn=setcdgta
ent-gttsel:gtin=4:tt=60:npv=5:naiv=6:cgpcsn=setcgpc:cgssn=112
ent-gttsel:gtia=2:tt=9:cdgttsn=lidb:eaglegen=yes
ent-gttsel:gti=0:cdgttsn=acdgta:selid=1
ent-gttsel:gtin16=0:cgpcsn=abc
ent-gttsel:gtin16=2:cgpcsn=abc:tt=10
ent-gttsel:gtin16=4:cgpcsn=abc:tt=10:np=x121:nai=natl
ent-gttsel:msgtype=u:gtin16=4:cgpcsn=abc:tt=10:np=x121:nai=natl
ent-gttsel:msgtype=u,us,x:gtii=4:cdgtasn=abc:tt=10:np=x121:nai=natl
Dependencies
The EGTT feature must be turned on before this command can be entered.
The np and npv parameters cannot be specified in the same command.
The nai and naiv parameters cannot be specified in the same command.
The gti, gtia=4, gti(x)=1, and gti(x)=3 parameters cannot be specified.
If the gti/gtia/gtii/gtin/gtin24/gtiis/gtins/gtin16=2 parameter is specified, then the np/npv and nai/naiv parameters cannot be specified.
If the gtii/gtin/gtin24/gtiis/gtins/gtin16=4 parameter is specified, the np(v) and nai(v) parameters must be specified. These parameters can be specified in any combination: np/naiv, npv/nai, np/nai, or npv/naiv.
A value of none cannot be specified for the gttsn, cdgtasn, cggtasn, cgpcsn, cdgttsn, and cggttsn parameters.
The GTT Selector table must be accessible.
The GTT Set table must be accessible.
At least one GTT set name parameter must be specified. These parameters include:
- cdgtasn, cggtasn, or cgpcsn if the OBSR feature is enabled
- cdgttsn or cggttsn if the FLOBR feature is turned on
- gttsn if the OBSR feature is not enabled and the FLOBR feature is not turned on
The OBSR feature must be enabled before the cggtasn, cgpcsn, cgssn, or cdgtasn parameters can be specified.
The SSNSELID Table cannot contain more than 100,000 entries.
The SSNSELID table must be accessible.
The linkset specified by the lsn parameter must already exist.
The Linkset table is corrupt or cannot be found.
The FLOBR feature must be turned on before the lsn, eaglegen, cdgttsn, and cggttsn parameters can be specified.
If the FLOBR feature is turned on, then the cdgtasn, cggtasn, and cgpcsn parameters cannot be specified.
The value specified for the cdgtasn or gttsn parameter must match the name of an existing GTT set.
The GTT set specified by the
cdgtasn or
gttsn parameter must have a set type
of
cdgta (see the
ent-gttset
command).
An entry cannot already exist that matches the
eaglegen, gti, tt, and np(v), and
nai(v) parameter combination for the
specified CdPA and/or CgPA selector. If a GTT Selector entry is already
provisioned for the given
gti, tt, np(v) and nai(v) combination with
msgtype=all
, another entry for the same combination
but different msgtype
(u/us/x/xs) is not allowed.
The GTT set specified by the gttsn, cdgtasn, or cdgttsn parameter must already exist in the GTT Set table.
The network domain of the specified GTT selector must match the domain of the GTT set that is specified by the gttsn, cdgtasn, or cdgttsn parameter, unless the domain of the GTT set has a value of cross.
The GTT set specified by the cgttsn, cggtasn or cgpcsn parameter must already exist in the GTT Set table.
The network domain of the GTT set that is specified by the cggttsn, cggtasn, or cgpcsn parameter must match the domain specified by the gti(x) parameter.
The set type of the GTT set specified by the cggtasn or cgpcsn parameter must match the set type of the corresponding entry in the GTT Set table.
The GTT Set specified by the cdgtasn or
gttsn parameter must have a set type
of
cdgta (see the
ent-gttset
command).
The gttsn parameter cannot be specified if the OBSR feature is enabled or the FLOBR feature is turned on.
The GTTDBMM Table cannot contain more than 42,502 entries.
The GTTDBMM table is corrupt or cannot be found.
A database error occurred while trying to access the SSNSELID table.
If the gti(x)=4 parameter is specified, then the GTT selector table cannot have more than 5 nai entries per tt/np combination.
The cggtasn, cgpcsn, and cggttsn parameters cannot be specified together in the command.
The gttsn, cdgtasn, and cdgttsn parameters cannot be specified together in the command.
If the gttsn, cdgttsn, or cdgtasn parameter is specified, then the cgssn parameter cannot be specified. If the cggtasn, cgpcsn or cggttsn parameter is specified, then the cgssn parameter must be specified.
If the cdgttsn or cggttsn parameter is specified, then the lsn parameter must be specified.
If the eaglegen=yes parameter is specified, then the msgtype, lsn, selid, gttsn, cdgtasn, cgssn, cggttsn, cggtasn, and cgpcsn parameters cannot be specified.
If the gti(x)=0 parameter is specified, then the eaglegen, tt, np/npv, and nai/naiv parameters cannot be specified.
If a value of 2 or 4 is specified for the gti(x) parameter, then the tt parameter must be specified.
For existing TTs with gtii/gtin/gtin24/gtiis/gtins/gtin16=4, the domain of the new entry must match the existing domain.
The MBR supported GTT set types (IMEI/IMSI/MSISDN/VLRNB/SMRPDA/SMRPOA) cannot be referenced by GTT selectors.
SSN configured for SFAPP cannot be used in any command for any configuration
Notes
For
gtii/gtin=4, DFLT may appear in the
rtrv-gttsel
output, but
dflt cannot be specified as value for
the
np or
nai parameters when the
ent-gttsel
command is entered. If a
new GTT selector is specified that matches an existing GTT selector’s GTI and
TT and the existing selector has
dflt as the value for the
np and/or
nai parameters, a new entry is
created with the new
np and
nai parameter values. The existing
GTT selector entry with the
dflt value is also retained. The
np/nai parameter value
dflt can be specified for the
chg/dlt/rtrv-gttsel
commands.
The Origin-based SCCP Routing feature allows two GTT sets to be assigned to a GTT selector: CDGTASN and CGGTASN or CDGTASN and CGPCSN. The CGGTASN and CGPCSN GTT sets are mutually exclusive and cannot be assigned to the same GTT selector.
There is no J7 FAK dependency on the GTIA/GTIN16/GTIN24 parameters. The command can be entered successfully whether the J7 FAK is enabled or not enabled.
GTT Selector entries configured using the GTIN24/GTIN16 parameters shall be treated as ITU-N24 entries if the J7 FAK is disabled and shall be treated as ITU-N16 entries if the J7 FAK is enabled.
In the msgtype parameter, the parameter values correspond to SCCP message types as given in the following list:
- 'u' implies SCCP UDT message
- 'us' implies SCCP UDTS message
- 'x' implies SCCP XUDT message
- 'xs' implies to SCCP XUDTS messages, and
- 'all' implies all SCCP messages
Using this parameter, a GTT Selector entry can be made to select one or more types of messages. For similar gti(x), tt, np and nai values but different msgtype values, different selector entries will be made.
The user cannot enter a selector with an existing message type again. For example, if the user is trying to add a selector with message type as "xs,u" and an existing message type is "xs,x", it cannot be added because the selector with message type "xs" already exists and the message type is a part of a key to the GTT Selector table and cannot be changed.
To enter a selector with message type xs,u either delete the existing xs,x entry and enter a selector again with "xs,x,u" as the message type, or add an another entry with the message type as "u". Please refer the output for example.
Output
ent-gttsel:gti=0:cdgttsn=acdgta
tekelecstp 10-04-05 15:41:49 EST Eagle 42.0.0
ent-gttsel:gti=0:cdgttsn=acdgta
Command entered at terminal #4.
ENT-GTTSEL: MASP A - COMPLTD
;
ent-gttsel:msgtype=u,us:gti=0:cdgttsn=acdgta
tekelecstp 17-05-11 13:09:15 EST EAGLE 46.6.0.0.0-71.2.0
ent-gttsel:msgtype=u,us:gti=0:cdgttsn=acdgta
Command entered at terminal #4.
ENT-GTTSEL: MASP A - COMPLTD
;
ent-gttsel:msgtype=x,xs:gtin=4:np=e164:nai=intl:tt=0:cggttsn=gttcggta
tekelecstp 17-12-27 06:35:47 EST EAGLE 46.6.0.0.0-71.21.0
ent-gttsel:msgtype=x,xs:gtin=4:np=e164:nai=intl:tt=0:cggttsn=gttcggta
Command entered at terminal #4.
ENT-GTTSEL: MASP A - COMPLTD
;
rtrv-gttsel
tekelecstp 17-12-27 06:35:51 EST EAGLE 46.6.0.0.0-71.21.0
rtrv-gttsel
Command entered at terminal #4.
GTI CG CDPA CGPA
MSGTYPE ANSI TT NP NAI SSN SELID LSN GTTSET GTTSET
GTI CG CDPA CGPA
MSGTYPE INT TT NP NAI SSN SELID LSN GTTSET GTTSET
GTI CG CDPA CGPA
MSGTYPE NAT TT NP NAI SSN SELID LSN GTTSET GTTSET
x,xs 4 0 e164 intl any none any ----- gttcggta
(--- ) (cggta)
GTI CG CDPA CGPA
MSGTYPE N24 TT NP NAI SSN SELID LSN GTTSET GTTSET
GTI CG CDPA CGPA
MSGTYPE INTS TT NP NAI SSN SELID LSN GTTSET GTTSET
GTI CG CDPA CGPA
MSGTYPE NATS TT NP NAI SSN SELID LSN GTTSET GTTSET
;
ent-gttsel:msgtype=xs,u:gtin=4:np=e164:nai=intl:tt=0:cggttsn=gttcggta
tekelecstp 17-12-27 06:36:27 EST EAGLE 46.6.0.0.0-71.21.0
ent-gttsel:msgtype=xs,u:gtin=4:np=e164:nai=intl:tt=0:cggttsn=gttcggta
Command entered at terminal #4.
E5121 Cmd Rej: CdPA/CgPA GTT Selector already exists
ENT-GTTSEL: MASP A - Command Aborted
ent-gttsel:msgtype=xs,u:gtin=4:np=e164:nai=intl:tt=0:cdgttsn=gttcdgta
tekelecstp 17-12-27 06:39:10 EST EAGLE 46.6.0.0.0-71.21.0
ent-gttsel:msgtype=xs,u:gtin=4:np=e164:nai=intl:tt=0:cdgttsn=gttcdgta
Command entered at terminal #4.
ENT-GTTSEL: MASP A - COMPLTD
;
rtrv-gttsel
tekelecstp 17-12-27 06:39:17 EST EAGLE 46.6.0.0.0-71.21.0
rtrv-gttsel
Command entered at terminal #4.
GTI CG CDPA CGPA
MSGTYPE ANSI TT NP NAI SSN SELID LSN GTTSET GTTSET
GTI CG CDPA CGPA
MSGTYPE INT TT NP NAI SSN SELID LSN GTTSET GTTSET
GTI CG CDPA CGPA
MSGTYPE NAT TT NP NAI SSN SELID LSN GTTSET GTTSET
x,xs 4 0 e164 intl any none any gttcdgta gttcggta
(cdgta) (cggta)
GTI CG CDPA CGPA
MSGTYPE N24 TT NP NAI SSN SELID LSN GTTSET GTTSET
GTI CG CDPA CGPA
MSGTYPE INTS TT NP NAI SSN SELID LSN GTTSET GTTSET
GTI CG CDPA CGPA
MSGTYPE NATS TT NP NAI SSN SELID LSN GTTSET GTTSET
;
Related Topics