4.170 copy-gpl

Use this command to copy all approved GPLs from one drive to another. The GPLs can be copied only from the fixed disk on the active TDM to the removable drive, or from the removable drive to the fixed disk on the standby TDM.

Parameters

ddrv (optional)
Destination drive. The identification of the disk to which the GPL is copied.
Range:
fixed
The fixed disk
remove
The removable drive
usb
The flush-mounted (not-latched) USB port on the MASP card.
dloc (optional)
The destination location of the GPLs to be copied.
Range:
1114
The TDM
1116
The TDM
1113
The latched USB port
1115
The latched USB port
Default:
none
sdrv (optional)
Source drive. The identification of the disk from which the GPL is copied.
Range:
fixed
The fixed disk
remove
The removable media drive
usb
The flush-mounted (not-latched) USB port on the MASP card.
sloc (optional)
The source location of the GPLs to be copied.
Range:
1114
The TDM
1116
The TDM
1113
The latched USB port
1115
The latched USB port
Default:
The location of the active TDM

Example

copy-gpl

copy-gpl:sloc=1115:dloc=1116

copy-gpl:sloc=1116

Dependencies

While this command is executing, the act/chg-gpl commands cannot be entered.

The standby fixed disk could not be accessed. There could be a hardware problem.

The active fixed disk could not be accessed. There could be a hardware problem.

The source and destination disks are not compatible. There could be a hardware problem

The system cannot determine the capacity of the disk that is being formatted.

The removable disk must be accessible.

The GPLs can be copied only from the fixed disk on the active TDM (sloc=1114 or sloc=1116) to the removable drive (dloc=1113 or dloc=1115), or from the removable drive (sloc=1113 or sloc=1115) to the fixed disk on the standby TDM (dloc=1114 or dloc=1116).

The source drive must be coherent when the command is executed.

The 1113 and 1115 locations are used by E5-MCAP cards. The 1114 and 1116 locations are used by E5-TDM cards.

The plug-in flash drive must be accessible in the Active OAM's flush-mounted USB port.

The specified disk type must match the specified location.

This command cannot be entered when CAT2 IPSM to OAM syncing is in progress.

Notes

This command has no effect on the GPLs stored on other cards (for example, SCCP).

Output

Copying the GPLs from the fixed disk on the active TDM (card location 1114) to the removable drive (card location 1113).

copy-gpl:sloc=1114:dloc=1113

    rlghncxa03w 09-01-07 00:57:31 EST  EAGLE 40.1.0
    COPY GPL:  MASP A - COPY STARTS ON ACTIVE MASP
    COPY GPL:  MASP A - COPY TO REMOVABLE MEDIA COMPLETE 
;

Copying the GPLs from the removable drive (card location 1115) to the fixed disk on the standby TDM (card location 1116).

copy-gpl:sloc=1115:dloc=1116

    rlghncxa03w 09-01-07 00:57:31 EST  EAGLE 40.1.0
    COPY GPL:  MASP B - COPY STARTS ON REMOVABLE DRIVE 
;

    rlghncxa03w 09-01-07 01:01:27 EST  EAGLE 40.1.0
    COPY GPL:  MASP B - COPY TO STANDBY MASP COMPLETE 
;

Copying the GPLs from the fixed disk on the active USB drive.

copy-gpl:sloc=1114:ddrv=usb

    e5oam 09-01-09 05:14:23 MST  EAGLE 40.1.0
    COPY GPL: MASP A - COPY STARTS ON ACTIVE MASP 
;

    e5oam 09-01-09 05:22:30 MST  EAGLE 40.1.0
    COPY GPL: MASP A - COPY TO USB DRIVE COMPLETE